HELLO! BOOT0 is starting! boot0 version : 3.1.0 reg_addr 0x01f00100 =0x00000000 reg_addr 0x01f00104 =0x00000000 reg_addr 0x01f00108 =0x00000000 reg_addr 0x01f0010c =0x00000000 reg_addr 0x01f00110 =0x00000000 reg_addr 0x01f00114 =0x00000000 DRAM DRIVE INFO: V1.4 DRAM CLK =480 MHZ DRAM simple test OK. dram size =512 sum=0xb382bd99 src_sum=0xb382bd99 Ready to disable icache. Jump to secend Boot. [ 0.213] U-Boot 2011.09-rc1-00000-g8a29683-dirty (Jan 20 2015 - 21:18:48) Allwinner Technology [ 0.222]version: 1.1.0 [ 0.297]pmbus: ready [ 0.299]PMU: AXP221 [ 0.302]PMU: AXP22x found [ 0.305]PMU: dcdc3 1200 [ 0.308]PMU: pll1 1008 Mhz,PLL6=600 Mhz AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz set power on vol to default dcdc1_vol = 3000 dcdc2_vol = 1100 dcdc3_vol = 1200 dcdc4_vol = 0 dcdc5_vol = 1500 aldo2_vol = 2500 aldo3_vol = 3000 find power_sply to end vbus pc exist, limit to pc fel key old mode run key detect no key found no key input dram_para_set start dram_para_set end [ 0.433]DRAM: 512 MiB relocation Offset is: 15b11000 smcl's set manager is NULL workmode = 0 [ 0.633]NAND: NAND_UbootInit NAND_UbootInit start NB1 : enter NAND_LogicInit uboot:physical version: 2 1b 20140616 1640 nand : get id_number_ctl fail, 1 uboot:nand info: a714dead ffff4a42 318c 40704 5 nand : get CapacityLevel fail, 5fb9c793 not burn nand partition table! NB1 : nftl num: 2 init nftl: 0 NB1 : NAND_LogicInit ok, result = 0x0 [ 1.223]sunxi flash init ok In: serial Out: serial Err: serial --------fastboot partitions-------- -total partitions:13- -name- -start- -size- bootloader : 1000000 2000000 env : 3000000 1000000 boot : 4000000 1000000 system : 5000000 30000000 data : 35000000 40000000 misc : 75000000 1000000 recovery : 76000000 2000000 cache : 78000000 8000000 metadata : 80000000 1000000 private : 81000000 1000000 klog : 82000000 1000000 alog : 83000000 4000000 UDISK : 87000000 0 ----------------------------------- base bootcmd=run setargs_nand boot_normal bootcmd set setargs_nand key 0 recovery key high 8, low 2 cant find fstbt value misc partition found Fastboot detected, will boot fastboot to be run cmd=run setargs_nand boot_fastboot mount part name bootloader cant open script.bin, maybe it is not exist WORK_MODE_BOOT board_status_probe [ 1.335]pre sys mode sunxi_bmp_logo_display screen_id =0, screen_width =1024, screen_height =600 [ 1.351]Hit any key to stop autoboot: 0 run usb fastboot sunxi_fastboot_init recv addr 0x41000000 send addr 0x54aa4090 delay time 0 usb init ok set address 0x18 [ 11.704]SUNXI_USB_FASTBOOT_SETUP [ 11.708]fastboot command = download:00b3a800 [ 11.712]download Starting download of 11773952 BYTES Starting download of 11 MB download response: DATA00b3a800 [ 12.105]fastboot transfer finish [ 12.109]SUNXI_USB_FASTBOOT_SETUP [ 12.112]fastboot command = boot [ 12.115]boot start addr 0x41000800 Booting kernel.. Image has cmdline:console=ttyS0,115200 ## Booting kernel from Legacy Image at 41000800 ... Image Name: Linux kernel Image Type: ARM Linux Multi-File Image (uncompressed) Data Size: 11770359 Bytes = 11.2 MiB Load Address: 80008000 Entry Point: 80008000 Contents: Image 0: 6790944 Bytes = 6.5 MiB Image 1: 4946629 Bytes = 4.7 MiB Image 2: 32767 Bytes = 32 KiB Verifying Checksum ... OK ## Loading init Ramdisk from multi component Legacy Image at 41000800 ... Loading Multi-File Image ... OK OK para err in disp_ioctl, cmd = 0xa,screen id = 1 [ 13.331][mmc]: MMC Device 2 not found [ 13.335][mmc]: mmc not find,so not exit NAND_UbootExit NB1 : NAND_LogicExit nand release dma:0 [ 13.339] Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00001029). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Allwinner sun9i Family ffffffff Allwinner sun8i Family ffffffff Allwinner sun7i (A20) Family ffffffff Allwinner sun6i (A31) Family ffffffff Allwinner sun4i/sun5i Families Please check your kernel config and/or bootloader.