[ 0.33]HELLO! BOOT0 is starting! [ 0.37]boot0 commit : 2320b4e28f694a40302a75531ea057ca7fcc0074 [ 0.44]boot0 version : 4.0 [ 0.47]set pll start [ 0.51]set pll end [ 0.87]rtc[0] value = 0x00000000 [ 0.90]rtc[1] value = 0x00000000 [ 0.93]rtc[2] value = 0x00000000 [ 0.97]rtc[3] value = 0x00000000 [ 0.100]rtc[4] value = 0x00000000 [ 0.103]rtc[5] value = 0x00000000 [ 0.107]DRAMC IS FOUR [ 0.109]DRAM BOOT DRIVE INFO: V1.1 [ 0.113]the chip id is 0x00000001 [ 0.116]the chip id is 0x00000001 [ 0.120]the chip id is 0x00000001 [ 0.123]the chip id is 0x00000001 [ 0.127]the chip id is 0x00000001 [ 0.134]PMU: [ 0.135]AXP221 [ 0.137]ddr voltage = 1250 mv [ 0.144]PMU: [ 0.145]AXP221 [ 0.147]ddr voltage = 1250 mv [ 0.158]PMU: [ 0.159]AXP221 [ 0.161]ddr voltage = 1500 mv [ 0.172]DRAM CLK =576 MHZ [ 0.174]DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) [ 0.180]DRAM zq value: 0x003b3bfb [ 0.186]DRAM SIZE =2048 M [ 0.189]DRAM simple test OK. [ 0.192]dram size =2048 [ 0.194]rtc standby flag is 0x00000000, super standby flag is 0x00000000 [ 0.203]card no is 0 [ 0.205]sdcard 0 line count 4 [ 0.208][mmc]: mmc driver ver 2016-07-01 15:30 [ 0.212][mmc]: sdc0 spd mode error, 2 [ 0.225][mmc]: Wrong media type 0x00000000 [ 0.229][mmc]: ***Try SD card 0*** [ 0.238][mmc]: HSSDR52/SDR25 4 bit [ 0.242][mmc]: 50000000 Hz [ 0.245][mmc]: 64000 MB [ 0.247][mmc]: ***SD/MMC 0 init OK!!!*** [ 0.369]Loading boot-pkg Succeed(index=0). [ 0.373]Entry_name = u-boot [ 0.392]Ready to disable icache. [ 0.395]Jump to secend Boot. U-Boot 2014.07 (May 10 2019 - 10:11:11) Allwinner Technology uboot commit : 8 i2c_init ok [ 0.461]pmbus: ready [ 0.480]PMU: AXP221 [ 0.480]PMU: AXP22x found [ 0.481]PMU: dcdc2 1160 [ 0.483]PMU: cpux 1008 Mhz,AXI=336 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz MBus=400Mhz set power on vol to default dcdc1_vol = 3300, onoff=1 dcdc2_vol = 1160, onoff=1 dcdc3_vol = 1100, onoff=1 dcdc4_vol = 1100, onoff=0 aldo1_vol = 2800, onoff=0 aldo2_vol = 1500, onoff=1 aldo3_vol = 3000, onoff=1 dc1sw_vol = 3000, onoff=0 dc5ldo_vol = 1100, onoff=0 dldo1_vol = 3300, onoff=0 dldo2_vol = 3300, onoff=0 dldo3_vol = 3300, onoff=0 dldo4_vol = 2500, onoff=0 eldo1_vol = 2800, onoff=0 eldo2_vol = 1500, onoff=0 eldo3_vol = 1200, onoff=0 gpio0_vol = 3300, onoff=0 gpio1_vol = 1800, onoff=0 find power_sply to end vbus exist BPI: bpi_boot_init_gpio ... set pin for gpio_pin_1 set pin for gpio_pin_2 set pin for gpio_pin_3 set pin for gpio_pin_4 run key detect BPI: BPI-M2 Ultra bpi_board_version: [40] no key found no uart input DRAM: 2 GiB fdt addr: 0xb6e81c78 Relocation Offset is: 75ed8000 In: serial Out: serial Err: serial gic: normal mode [ 0.711]start drv_disp_init init_clocks: finish init_clocks. pwm_request: reg = 0x1c23400. pwm = 0. request pwm success, pwm = 0. tv_init: tv_init: drv_disp_init finish boot_disp.output_disp=0 boot_disp.output_type=3 boot_disp.output_mode=5 boot_disp.auto_hpd=1 disp0 device type(4) enable attched ok, mgr0<-->device0, type=4, mode=5 [ 1.395]end workmode = 0,storage type = 1 [ 1.395]MMC: 0 [mmc]: mmc driver ver 2016-07-01 15:50:00 [mmc]: boot_card_no error 1 SUNXI SD/MMC: 0 [mmc]: 50 MHz... [mmc]: sample: 51 - 196(ps) [mmc]: 100 MHz... [mmc]: sample: 26 - 192(ps) [mmc]: 200 MHz... [mmc]: sample: 13 - 192(ps) [mmc]: BPI: 0 CARD_TYPE_SD [mmc]: media type 0x8000001 [mmc]: ************Try SD card 0************ [mmc]: host caps: 0x27 [mmc]: MID 00 PSN 00003c32 [mmc]: PNM -- 0x00-00-00-00-00 [mmc]: PRV 0.0 [mmc]: MDT m-9 y-2014 [mmc]: speed mode : HSSDR52/SDR25 [mmc]: clock : 50000000 Hz [mmc]: bus_width : 4 bit [mmc]: user capacity : 64000 MB [mmc]: ************SD/MMC 0 init OK!!!************ [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte [mmc]: secure_feature : 0x0 [mmc]: secure_removal_type : 0x0 [ 1.570]sunxi flash init ok sunxi secure storage is not supported [ 1.577]usb burn from boot delay time 0 [ 1.668]usb prepare ok [ 2.467]timer occur [ 2.468]overtime [ 2.501]do_burn_from_boot usb : no usb exist --------fastboot partitions-------- -total partitions:7- -name- -start- -size- boot-res : 1000000 1000000 env : 2000000 100000 boot : 2100000 800000 private : 2900000 100000 misc : 2a00000 100000 rootfs : 2b00000 a000000 UDISK : cb00000 0 ----------------------------------- base bootcmd=run setargs_nand boot_normal bootcmd set setargs_mmc key 0 cant find rcvy value cant find fstbt value misc partition found to be run cmd=run setargs_mmc boot_normal update dtb dram start update dtb dram end sunxi_serial: serial_feature is not exist serial is: 141050370310581c0b8e BPI: axp_probe_battery_exist(0) BPI: BatExist(0) pmu_bat_unused(0) PowerBus = 3( 2:vBus 3:acBus other: not exist) no battery, limit to dc no battery exist sunxi_bmp_logo_display reading bootlogo.bmp 3686538 bytes read in 210 ms (16.7 MiB/s) bmp file buffer: 0x40000000, bmp_info.buffer: 46400000 screen_id =0, screen_width =1280, screen_height =720 frame buffer address 46400036 Net: No ethernet found. [ 2.970]inter uboot shell Hit any key to stop autoboot: 0 [mmc]: MMC Device 2 not found ** Bad device mmc 2 ** reading bananapi/bpi-m2u/linux/720p/bpiEnv.txt [mmc]: blkcnt should not be 0 17 bytes read in 6 ms (2 KiB/s) Loaded environment from bpiEnv.txt reading bananapi/bpi-m2u/linux/720p/uEnv.txt 1883 bytes read in 6 ms (305.7 KiB/s) Loaded environment from uEnv.txt Running uenvcmd ... Banana Pi bpi-m2u chip: r40 Service: linux bpiuser: 720p reading bananapi/bpi-m2u/linux/uImage 6833112 bytes read in 374 ms (17.4 MiB/s) reading bananapi/bpi-m2u/linux/uInitrd 5161212 bytes read in 281 ms (17.5 MiB/s) ## Booting kernel from Legacy Image at 47000000 ... Image Name: Linux-3.10.108-BPI-M2U-Kernel Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6833048 Bytes = 6.5 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 49000000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5161148 Bytes = 4.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK reserving fdt memory region: addr=43000000 size=800 Loading Ramdisk to 5fb13000, end 5ffff0bc ... OK Using Device Tree in place at 45000000, end 450191ff prepare for kernel [mmc]: MMC Device 2 not found [mmc]: mmc 2 not find, so not exit Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.108-BPI-M2U-Kernel (root@bpi) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #5 SMP Fri May 10 10:12:10 CST 2019 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: sun8iw11p1, model: sun8iw11p1 [ 0.000000] cma: CMA: reserved 256 MiB at 4f800000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] On node 0 totalpages: 524288 [ 0.000000] free_area_init_node: node 0, pgdat c0d98480, node_mem_map c0e06000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2576 pages used for memmap [ 0.000000] HighMem zone: 329728 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c1e30000 s9664 r8192 d14912 u32768 [ 0.000000] pcpu-alloc: s9664 r8192 d14912 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522768 [ 0.000000] Kernel command line: board=bpi-m2u console=earlyprintk=sunxi-uart,0x01c28000 console=tty1 console=ttyS0,115200n8 no_console_suspend consoleblank=0 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait bootmenutimeout=10 datadev=mmcblk0p2 service=linux bpiuser=720p mac_addr= enforcing=1 initcall_debug=0 loglevel=8 init=/init cma=256M panic=10 fsck.mode=force fsck.repair=yes disp.screen0_output_type=3 disp.screen0_output_mode=5 disp.screen1_output_type=3 disp.screen1_output_mode=5 androidboot.serialno=141050370310581c0b8e [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 4194304 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 2048MB = 2048MB total [ 0.000000] Memory: 1793428k/1793428k available, 303724k reserved, 1318912K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0c2fb20 (12447 kB) [ 0.000000] .init : 0xc0c30000 - 0xc0c7a5c0 ( 298 kB) [ 0.000000] .data : 0xc0c7c000 - 0xc0d99a10 (1143 kB) [ 0.000000] .bss : 0xc0d99a10 - 0xc0e05168 ( 430 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] of_sunxi_clocks_init : sunxi_clk_base[0xf1c20000] [ 0.000000] pll_audio-set_default_rate=24576000 success! [ 0.000000] pll_periph0-set_default_rate=600000000 success! [ 0.000000] pll_de-set_default_rate=297000000 success! [ 0.000000] ahb1-set_default_rate=200000000 success! [ 0.000000] apb1-set_default_rate=100000000 success! [ 0.000000] apb2-set_default_rate=24000000 success! [ 0.000000] de-set_default_rate=297000000 success! [ 0.000000] de_mp-set_default_rate=297000000 success! [ 0.000000] mbus-set_default_rate=400000000 success! [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] Switching to timer-based delay loop [ 0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty1] enabled [ 0.010000] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.010000] pid_max: default: 32768 minimum: 301 [ 0.010000] Security Framework initialized [ 0.010000] AppArmor: AppArmor initialized [ 0.010000] Mount-cache hash table entries: 512 [ 0.018223] Initializing cgroup subsys memory [ 0.018296] Initializing cgroup subsys devices [ 0.018315] Initializing cgroup subsys freezer [ 0.018330] Initializing cgroup subsys blkio [ 0.018344] Initializing cgroup subsys perf_event [ 0.018411] CPU: Testing write buffer coherency: ok [ 0.018880] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.018923] Setting up static identity map for 0xc08c5050 - 0xc08c50a8 [ 0.020448] CPU1: Booted secondary processor [ 0.020448] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.020569] CPU2: Booted secondary processor [ 0.020569] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.020569] CPU3: Booted secondary processor [ 0.020569] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.020569] Brought up 4 CPUs [ 0.020569] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.020608] devtmpfs: initialized [ 0.025137] xor: measuring software checksum speed [ 0.120011] arm4regs : 1280.000 MB/sec [ 0.220009] 8regs : 757.200 MB/sec [ 0.320010] 32regs : 860.000 MB/sec [ 0.320024] xor: using function: arm4regs (1280.000 MB/sec) [ 0.320053] atomic64 test passed [ 0.320065] pinctrl core: initialized pinctrl subsystem [ 0.333244] NET: Registered protocol family 16 [ 0.333244] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.333244] dump_class_init,844, success [ 0.340862] sun8iw11p1-pinctrl pio: initialized sunXi PIO driver [ 0.350308] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.350308] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.400191] bio: create slab at 0 [ 0.568715] raid6: int32x1 173 MB/s [ 0.738410] raid6: int32x2 155 MB/s [ 0.908379] raid6: int32x4 166 MB/s [ 1.078564] raid6: int32x8 150 MB/s [ 1.078582] raid6: using algorithm int32x1 (173 MB/s) [ 1.078595] raid6: using intx1 recovery algorithm [ 1.080091] pwm module init! [ 1.080369] platform pwm0: there is no bind_pwm, set bind_pwm 255! [ 1.080369] platform pwm0: there is no dead time, set bind_pwm 255! [ 1.080436] SCSI subsystem initialized [ 1.080436] libata version 3.00 loaded. [ 1.080436] usbcore: registered new interface driver usbfs [ 1.080436] usbcore: registered new interface driver hub [ 1.080436] usbcore: registered new device driver usb [ 1.090799] Linux video capture interface: v2.00 [ 1.090857] [axp221s] chip id detect 0x6 ! [ 1.090857] [axp221s] enable dcdc2 dvm. [ 1.110205] Advanced Linux Sound Architecture Driver Initialized. [ 1.110317] Bluetooth: Core ver 2.16 [ 1.110317] NET: Registered protocol family 31 [ 1.110317] Bluetooth: HCI device and connection manager initialized [ 1.110317] Bluetooth: HCI socket layer initialized [ 1.110317] Bluetooth: L2CAP socket layer initialized [ 1.110317] Bluetooth: SCO socket layer initialized [ 1.110317] cfg80211: Calling CRDA to update world regulatory domain [ 1.110648] NetLabel: Initializing [ 1.110665] NetLabel: domain hash size = 128 [ 1.110677] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.110758] NetLabel: unlabeled traffic allowed by default [ 1.110814] [pm]aw_pm_init! [ 1.110814] np name = /soc@01c00000/rtc@01c20400. [ 1.110814] base = f1c20500, len = 4. [ 1.110814] pmu1 does not exist. [ 1.110814] add_sys_pwr_dm: get ldo name for id: vdd-cpus failed [ 1.110814] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed [ 1.120583] add_sys_pwr_dm: get ldo name for id: vcc-pl failed [ 1.120765] add_sys_pwr_dm: axp22_dcdc1 ldo already alwayson. [ 1.120765] after inited: sys_mask config = 0x84815. [ 1.120765] Warning: can not find np for dynamic_standby_para. [ 1.120765] [pm]valid [ 1.120765] [pm]valid [ 1.120815] sunxi budget cooling probe start ! [ 1.120815] CPU freq cooling register Success [ 1.120815] CPU hotplug cooling register Success [ 1.120815] CPU budget cooling register Success [ 1.120815] input: sunxi-ths as /devices/virtual/input/input0 [ 1.120815] thermal thermal_zone0: failed to read out thermal zone 0 [ 1.120815] Switching to clocksource arch_sys_counter [ 1.121162] FS-Cache: Loaded [ 1.121231] CacheFiles: Loaded [ 1.121231] AppArmor: AppArmor Filesystem Enabled [ 1.141901] NET: Registered protocol family 2 [ 1.142884] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.143025] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.143146] TCP: Hash tables configured (established 8192 bind 8192) [ 1.143225] TCP: reno registered [ 1.143246] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.143309] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.143656] NET: Registered protocol family 1 [ 1.144107] RPC: Registered named UNIX socket transport module. [ 1.144130] RPC: Registered udp transport module. [ 1.144142] RPC: Registered tcp transport module. [ 1.144155] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.164683] Trying to unpack rootfs image as initramfs... [ 1.499376] Freeing initrd memory: 5040K [ 1.501213] lock super standby defaultly! [ 1.501244] lookup_scene_lock_name: new scene lock super_standby [ 1.501258] scene_lock_init name=super_standby [ 1.501272] scene_lock: super_standby, type 5, count 1 [ 1.502236] audit: initializing netlink socket (disabled) [ 1.502301] type=2000 audit(1.500:1): initialized [ 1.503492] bounce pool size: 64 pages [ 1.503837] VFS: Disk quotas dquot_6.5.2 [ 1.503989] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.504866] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.505715] NFS: Registering the id_resolver key type [ 1.505788] Key type id_resolver registered [ 1.505803] Key type id_legacy registered [ 1.505825] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.506454] Key type cifs.spnego registered [ 1.506500] Key type cifs.idmap registered [ 1.506518] NTFS driver 2.1.30 [Flags: R/W]. [ 1.507005] fuse init (API version 7.22) [ 1.507682] Registering sdcardfs 3.1.0 [ 1.507896] JFS: nTxBlock = 8192, nTxLock = 65536 [ 1.517403] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.518774] bio: create slab at 1 [ 1.519558] Btrfs loaded [ 1.519724] ceph: loaded (mds proto 32) [ 1.520102] aufs 3.10-20141215 [ 1.520131] msgmni has been set to 1448 [ 1.521969] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.522125] io scheduler noop registered [ 1.522142] io scheduler deadline registered [ 1.522236] io scheduler cfq registered (default) [ 1.523151] OF: no ranges; cannot translate [ 1.523179] OF: no ranges; cannot translate [ 1.523455] OF: no ranges; cannot translate [ 1.523476] OF: no ranges; cannot translate [ 1.524336] [DISP]disp_module_init [ 1.525131] [DISP]parser_disp_init_para: screen0_output_type(3) [ 1.525158] [DISP]parser_disp_init_para: screen0_output_mode(5) value(5) [ 1.525173] [DISP]parser_disp_init_para: screen1_output_type(3) [ 1.525189] [DISP]parser_disp_init_para: screen1_output_mode(5) value(5) [ 1.525214] [DISP] boot_disp:0x405 [ 1.553636] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.554161] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.554550] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.554933] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.555316] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.555698] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.556080] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.556463] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.556846] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.557228] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 1.557253] [DISP] fb_base:0x46400000 [ 1.636826] Console: switching to colour frame buffer device 160x45 [ 1.652597] [DISP]disp_module_init finish [ 1.660545] uart0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a SUNXI [ 1.660718] sw_uart_pm()959 - uart0 clk is already enable [ 1.660860] sw_console_setup()1270 - console setup baud 115200 parity n bits 8, flow n [ 2.965873] console [ttyS0] enabled [ 2.970565] uart2: ttyS2 at MMIO 0x1c28800 (irq = 35) is a SUNXI [ 2.978103] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 36) is a SUNXI [ 2.986390] misc dump reg init [ 2.990652] [drm] Initialized drm 1.1.0 20060810 [ 3.007016] brd: module loaded [ 3.020875] loop: module loaded [ 3.029837] [NAND]Failed to insmod nand!!! [ 3.039558] sunxi-bt bt: bt_power_name (vcc-wifi-2) [ 3.049898] sunxi-bt bt: io_regulator_name (vcc-io-wifi) [ 3.049924] sunxi-bt bt: bt_rst gpio=236 mul-sel=1 pull=1 drv_level=1 data=0 [ 3.049964] sunxi-bt bt: clk_name (outa) [ 3.070209] sunxi-bt bt: block state already is 1 [ 3.093954] sunxi-wlan wlan: wlan_busnum (1) [ 3.103659] sunxi-wlan wlan: wlan_power_name (vcc-wifi) [ 3.114331] sunxi-wlan wlan: io_regulator_name (vcc-io-wifi) [ 3.125830] sunxi-wlan wlan: request pincrtl handle for device [wlan] failed [ 3.138475] sunxi-wlan wlan: wlan_regon gpio=202 mul-sel=1 pull=1 drv_level=1 data=0 [ 3.152297] /soc@01c00000/wlan: could not find phandle [ 3.162699] sunxi-wlan wlan: get gpio wlan_hostwake failed [ 3.173444] sunxi-wlan wlan: clk_name (outa) [ 3.182969] Loading iSCSI transport class v2.0-870. [ 3.193993] iscsi: registered transport (tcp) [ 3.204122] sunxi-ahci sata: sata_regulator0 "vdd-sata-25"! [ 3.214788] sunxi-ahci sata: sata_regulator1 "vdd-sata-12"! [ 3.226244] sunxi-ahci sata: regulator "vdd-sata-25" voltage set: 2500000 to 2500000! [ 3.240171] sunxi-ahci sata: regulator "vdd-sata-12" voltage set: 1200000 to 1200000! [ 3.255217] sunxi-ahci sata: frequncy of module clk for AHCI: 100000000 [ 3.266643] sunxi-ahci sata: frequncy of pll clk for AHCI: 100000000 [ 3.340027] sunxi-ahci sata: SATA power enable do not exist!! [ 3.350315] sunxi-ahci sata: controller can't do PMP, turning off CAP_PMP [ 3.361705] sunxi-ahci sata: forcing PORTS_IMPL to 0x1 [ 3.371205] sunxi-ahci sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.384189] sunxi-ahci sata: flags: ncq sntf pm led clo only pio slum part ccc [ 3.396474] dma_alloc_coherent mem = 0xcf840000, size = 0x16500, mem_dma=0x4f840000 [ 3.409878] scsi0 : sunxi-ahci [ 3.417698] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c181ff] port 0x100 irq 88 [ 3.431803] spi spi0: master is unqueued, this is deprecated [ 3.445724] WARNING: Get ephy clock is failed [ 3.455953] PPP generic driver version 2.4.2 [ 3.464940] NET: Registered protocol family 24 [ 3.473700] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.485064] get ehci0-controller, regulator_io is no nocare [ 3.495212] [sunxi-ehci0]: probe, pdev->name: 1c14000.ehci0-controller, sunxi_ehci: 0xc0df5678, 0x:f1c14000, irq_no:47 [ 3.511313] sunxi-ehci 1c14000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.525627] sunxi-ehci 1c14000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 3.539878] sunxi-ehci 1c14000.ehci0-controller: irq 71, io mem 0xc0df4efc [ 3.570033] sunxi-ehci 1c14000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 3.582112] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.593960] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.606281] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.618920] usb usb1: Manufacturer: Linux 3.10.108-BPI-M2U-Kernel ehci_hcd [ 3.630933] usb usb1: SerialNumber: sunxi-ehci [ 3.641122] hub 1-0:1.0: USB hub found [ 3.649534] hub 1-0:1.0: 1 port detected [ 3.658691] [ehci0-controller]: sunxi_usb_disable_ehci [ 3.668769] [sunxi-ehci0]: remove, pdev->name: 1c14000.ehci0-controller, sunxi_ehci: 0xc0df5678 [ 3.682928] sunxi-ehci 1c14000.ehci0-controller: remove, state 1 [ 3.694056] usb usb1: USB disconnect, device number 1 [ 3.705846] sunxi-ehci 1c14000.ehci0-controller: USB bus 1 deregistered [ 3.718412] get drv_vbus is fail, 84 [ 3.726894] get ehci1-controller, regulator_io is no nocare [ 3.737676] [sunxi-ehci1]: probe, pdev->name: 1c19000.ehci1-controller, sunxi_ehci: 0xc0df581c, 0x:f1c19000, irq_no:6c [ 3.754375] sunxi-ehci 1c19000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.769367] sunxi-ehci 1c19000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 3.780042] ata1: SATA link down (SStatus 0 SControl 300) [ 3.795133] sunxi-ehci 1c19000.ehci1-controller: irq 108, io mem 0xc0df4efc [ 3.820038] sunxi-ehci 1c19000.ehci1-controller: USB 0.0 started, EHCI 1.00 [ 3.832865] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.845462] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.858549] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.871961] usb usb1: Manufacturer: Linux 3.10.108-BPI-M2U-Kernel ehci_hcd [ 3.884687] usb usb1: SerialNumber: sunxi-ehci [ 3.895466] hub 1-0:1.0: USB hub found [ 3.904588] hub 1-0:1.0: 1 port detected [ 3.914178] get drv_vbus is fail, 84 [ 3.922906] get ehci2-controller, regulator_io is no nocare [ 3.933860] [sunxi-ehci2]: probe, pdev->name: 1c1c000.ehci2-controller, sunxi_ehci: 0xc0df59c0, 0x:f1c1c000, irq_no:6e [ 3.950757] sunxi-ehci 1c1c000.ehci2-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.965881] sunxi-ehci 1c1c000.ehci2-controller: new USB bus registered, assigned bus number 2 [ 3.980840] sunxi-ehci 1c1c000.ehci2-controller: irq 110, io mem 0xc0df4efc [ 4.010046] sunxi-ehci 1c1c000.ehci2-controller: USB 0.0 started, EHCI 1.00 [ 4.022818] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.035239] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.048017] usb usb2: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.061107] usb usb2: Manufacturer: Linux 3.10.108-BPI-M2U-Kernel ehci_hcd [ 4.073532] usb usb2: SerialNumber: sunxi-ehci [ 4.084123] hub 2-0:1.0: USB hub found [ 4.093021] hub 2-0:1.0: 1 port detected [ 4.102740] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.114539] get ohci0-controller, regulator_io is no nocare [ 4.125495] [sunxi-ohci0]: probe, pdev->name: 1c14000.ohci0-controller, sunxi_ohci: 0xc0df4fe8 [ 4.139923] sunxi-ohci 1c14000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.154527] sunxi-ohci 1c14000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 4.169088] sunxi-ohci 1c14000.ohci0-controller: irq 72, io mem 0xc0df0a88 [ 4.244031] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.256529] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.269365] usb usb3: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.282111] usb usb3: Manufacturer: Linux 3.10.108-BPI-M2U-Kernel ohci_hcd [ 4.294553] usb usb3: SerialNumber: sunxi-ohci [ 4.305065] hub 3-0:1.0: USB hub found [ 4.313962] hub 3-0:1.0: 1 port detected [ 4.323147] [ohci0-controller]: sunxi_usb_disable_ohci [ 4.333315] [sunxi-ohci0]: remove, pdev->name: 1c14000.ohci0-controller, sunxi_ohci: 0xc0df4fe8 [ 4.347569] sunxi-ohci 1c14000.ohci0-controller: remove, state 1 [ 4.358786] usb usb3: USB disconnect, device number 1 [ 4.369706] sunxi-ohci 1c14000.ohci0-controller: USB bus 3 deregistered [ 4.382309] get drv_vbus is fail, 84 [ 4.390824] get ohci1-controller, regulator_io is no nocare [ 4.401669] [sunxi-ohci1]: probe, pdev->name: 1c19000.ohci1-controller, sunxi_ohci: 0xc0df518c [ 4.415960] sunxi-ohci 1c19000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.430365] sunxi-ohci 1c19000.ohci1-controller: new USB bus registered, assigned bus number 3 [ 4.444672] sunxi-ohci 1c19000.ohci1-controller: irq 96, io mem 0xc0df0a88 [ 4.514035] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.526423] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.539258] usb usb3: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.552021] usb usb3: Manufacturer: Linux 3.10.108-BPI-M2U-Kernel ohci_hcd [ 4.564397] usb usb3: SerialNumber: sunxi-ohci [ 4.574730] hub 3-0:1.0: USB hub found [ 4.583451] hub 3-0:1.0: 1 port detected [ 4.592655] get drv_vbus is fail, 84 [ 4.601114] get ohci2-controller, regulator_io is no nocare [ 4.611852] [sunxi-ohci2]: probe, pdev->name: 1c1c000.ohci2-controller, sunxi_ohci: 0xc0df5330 [ 4.626083] sunxi-ohci 1c1c000.ohci2-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.640441] sunxi-ohci 1c1c000.ohci2-controller: new USB bus registered, assigned bus number 4 [ 4.654698] sunxi-ohci 1c1c000.ohci2-controller: irq 97, io mem 0xc0df0a88 [ 4.724023] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.736291] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.749024] usb usb4: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.761663] usb usb4: Manufacturer: Linux 3.10.108-BPI-M2U-Kernel ohci_hcd [ 4.774013] usb usb4: SerialNumber: sunxi-ohci [ 4.784293] hub 4-0:1.0: USB hub found [ 4.792970] hub 4-0:1.0: 1 port detected [ 4.802640] usbcore: registered new interface driver usb-storage [ 4.813988] usbcore: registered new interface driver ums-alauda [ 4.825105] usbcore: registered new interface driver ums-cypress [ 4.836248] usbcore: registered new interface driver ums-datafab [ 4.847303] usbcore: registered new interface driver ums_eneub6250 [ 4.858464] usbcore: registered new interface driver ums-freecom [ 4.869357] usbcore: registered new interface driver ums-isd200 [ 4.880117] usbcore: registered new interface driver ums-jumpshot [ 4.891042] usbcore: registered new interface driver ums-karma [ 4.901676] usbcore: registered new interface driver ums-onetouch [ 4.912432] usbcore: registered new interface driver ums-realtek [ 4.922928] usbcore: registered new interface driver ums-sddr09 [ 4.933230] usbcore: registered new interface driver ums-sddr55 [ 4.943425] usbcore: registered new interface driver ums-usbat [ 4.953635] usbcore: registered new interface driver usbserial [ 4.963600] usbcore: registered new interface driver usbserial_generic [ 4.974184] usbserial: USB Serial support registered for generic [ 4.984808] mousedev: PS/2 mouse device common for all mice [ 4.995125] sunxi_keyboard_startup: keyboard has no clk. [ 5.004569] input: sunxi-keyboard as /devices/virtual/input/input1 [ 5.015861] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0 [ 5.025843] sunxi-rtc rtc: RTC enabled [ 5.033642] i2c /dev entries driver [ 5.041827] IR NEC protocol handler initialized [ 5.050232] Registered IR keymap rc_map_sunxi [ 5.058615] input: sunxi_ir_recv as /devices/soc/ir0/rc/rc0/input2 [ 5.068907] rc0: sunxi_ir_recv as /devices/soc/ir0/rc/rc0 [ 5.080379] axp22_dcdc1: unsupportable voltage range: 858992688-3400000uV [ 5.091961] sunxi cedar version 0.1 [ 5.099044] [cedar]: install start!!! [ 5.106330] cedar_ve: cedar-ve the get irq is 85 [ 5.114999] [cedar]: install end!!! [ 5.122777] input: axp22-powerkey as /devices/soc/twi0/i2c-0/0-0034/axp22-powerkey/input/input3 [ 5.149637] sunxi gpu cooling probe start ! [ 5.157457] CPU gpu cooling register Success [ 5.166367] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 5.178621] device-mapper: uevent: version 1.0.3 [ 5.187363] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com [ 5.200362] Bluetooth: Virtual HCI driver ver 1.3 [ 5.212402] cpuidle: using governor ladder [ 5.219599] cpuidle: using governor menu [ 5.227875] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v0.59 2016-08-17 15:15) Compiled in Mar 13 2019 at 15:47:55 [ 5.243217] sunxi-mmc sdc0: ***ctl-spec-caps*** 8 [ 5.251504] sunxi-mmc sdc0: regulator prop vmmc,str vcc-sdcv [ 5.260880] sunxi-mmc sdc0: regulator prop vqmmc,str vcc-sdcvq33 [ 5.270662] sunxi-mmc sdc0: regulator prop vdmmc,str vcc-sdcvd [ 5.281334] sunxi-mmc sdc0: Got CD GPIO #237. [ 5.289956] sunxi-mmc sdc0: base:0xf1c0f000 irq:64 [ 5.299067] sunxi-mmc sdc2: SD/MMC/SDIO Host Controller Driver(v0.59 2016-08-17 15:15) Compiled in Mar 13 2019 at 15:47:55 [ 5.314767] sunxi-mmc sdc2: regulator prop vmmc,str vcc-emmcv [ 5.324573] sunxi-mmc sdc2: regulator prop vqmmc,str vcc-emmcv [ 5.334500] sunxi-mmc sdc2: regulator prop vdmmc,str none [ 5.344014] axp22_dcdc1: Failed to create debugfs directory [ 5.353741] sunxi-mmc sdc2: No vdmmc regulator found [ 5.364435] sunxi-mmc sdc2: sdc set ios: clk 0Hz bm PP pm UP vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.380204] *mmc0 detect cd change* [ 5.387698] *mmc0 lock* [ 5.390112] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.408752] sunxi-mmc sdc0: sdc set ios: clk 0Hz bm PP pm UP vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.410167] sunxi-mmc sdc2: base:0xf1c11000 irq:66 [ 5.410627] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v0.59 2016-08-17 15:15) Compiled in Mar 13 2019 at 15:47:55 [ 5.410655] sunxi-mmc sdc1: Can't get vmmc regulator string [ 5.410660] sunxi-mmc sdc1: Can't get vqmmc regulator string [ 5.410664] sunxi-mmc sdc1: Can't get vdmmc regulator string [ 5.410667] get() with no identifier [ 5.410668] get() with no identifier [ 5.410669] get() with no identifier [ 5.410673] sunxi-mmc sdc1: No vmmc regulator found [ 5.410677] sunxi-mmc sdc1: No vqmmc regulator found [ 5.410681] sunxi-mmc sdc1: No vdmmc regulator found [ 5.529571] sunxi-mmc sdc1: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 5.540028] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.557900] sunxi-mmc sdc1: no vqmmc,Check if there is regulator [ 5.560843] sunxi-mmc sdc0: smc 0 p0 err, cmd 52, RTO !! [ 5.561675] sunxi-mmc sdc0: smc 0 p0 err, cmd 52, RTO !! [ 5.561694] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.564097] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.566280] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !! [ 5.567107] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !! [ 5.567933] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !! [ 5.568757] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !! [ 5.569401] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B [ 5.569446] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B [ 5.571845] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B [ 5.596860] mmc0: host does not support reading read-only switch. assuming write-enable. [ 5.598540] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing SD-HS(SDR25) dt B [ 5.598585] sunxi-mmc sdc0: sdc set ios: clk 50000000Hz bm PP pm ON vdd 15 width 1 timing SD-HS(SDR25) dt B [ 5.598700] sunxi-mmc sdc0: sdc set ios: clk 50000000Hz bm PP pm ON vdd 15 width 4 timing SD-HS(SDR25) dt B [ 5.598729] mmc0: new high speed SDXC card at address 0001 [ 5.755804] mmcblk0: mmc0:0001 62.5 GiB [ 5.764887] mmcblk0: p1 p2 [ 5.772737] sunxi-mmc sdc2: smc 1 p2 err, cmd 52, RTO !! [ 5.780035] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 5.796664] sunxi-mmc sdc2: smc 1 p2 err, cmd 52, RTO !! [ 5.805771] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.805883] sunxi-mmc sdc1: base:0xf1c10000 irq:65 [ 5.806892] gpio_led_probe start [ 5.806930] led1 gpio number is 244 [ 5.806934] led1_trigger led trigger name is default-on [ 5.806940] led2 gpio number is 245 [ 5.806942] led2_trigger led trigger name is heartbeat [ 5.806948] led3 gpio number is 246 [ 5.806950] led3_trigger led trigger name is mmc0 [ 5.808350] hidraw: raw HID events driver (C) Jiri Kosina [ 5.815335] usbcore: registered new interface driver usbhid [ 5.815339] usbhid: USB HID core driver [ 5.909321] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.910866] usbcore: registered new interface driver snd-usb-audio [ 5.912078] headphonevol:59, spkervol:27, maingain:4, pa_sleep_time:350 [ 5.946306] sunxi-mmc sdc2: smc 1 p2 err, cmd 8, RTO !! [ 5.947016] sunxi-codec-machine sndcodec: sun8iw11codec <-> 1c22c00.cpudai0-controller mapping ok [ 5.969837] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !! [ 5.979916] input: audiocodec Headphone Jack as /devices/soc/sndcodec/sound/card0/input4 [ 5.979922] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !! [ 5.980752] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !! [ 5.981579] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !! [ 5.982411] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !! [ 5.983239] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !! [ 5.984066] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !! [ 5.984893] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !! [ 5.984915] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 5.985323] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B [ 5.985369] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B [ 5.985415] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B [ 5.987818] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B [ 6.011182] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B [ 6.022740] mmc1: BKOPS_EN bit is not set [ 6.023703] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 7 width 1 timing MMC-HS(SDR20) dt B [ 6.023746] mmc1: Check switch ready sunxi_mmc_check_timing_switch_done [ 6.024075] sunxi-mmc sdc2: sdc set ios: clk 50000000Hz bm PP pm ON vdd 7 width 1 timing MMC-HS(SDR20) dt B [ 6.024190] sunxi-mmc sdc2: sdc set ios: clk 50000000Hz bm PP pm ON vdd 7 width 8 timing MMC-HS(SDR20) dt B [ 6.024326] mmc1: new high speed MMC card at address 0001 [ 6.024861] mmcblk1: mmc1:0001 8WPD3R 7.28 GiB [ 6.025015] mmcblk1boot0: mmc1:0001 8WPD3R partition 1 4.00 MiB [ 6.025163] mmcblk1boot1: mmc1:0001 8WPD3R partition 2 4.00 MiB [ 6.026356] mmcblk1: p1 [ 6.028481] mmcblk1boot1: unknown partition table [ 6.030047] mmcblk1boot0: unknown partition table [ 6.031187] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !! [ 6.032013] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !! [ 6.032034] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 6.034470] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 6.036342] sunxi-mmc sdc1: smc 2 p1 err, cmd 8, RTO !! [ 6.037165] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !! [ 6.037988] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !! [ 6.038808] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !! [ 6.039630] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !! [ 6.040454] sunxi-mmc sdc1: smc 2 p1 err, cmd 55, RTO !! [ 6.041278] sunxi-mmc sdc1: smc 2 p1 err, cmd 55, RTO !! [ 6.042101] sunxi-mmc sdc1: smc 2 p1 err, cmd 55, RTO !! [ 6.042923] sunxi-mmc sdc1: smc 2 p1 err, cmd 55, RTO !! [ 6.042941] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 6.043796] sunxi-mmc sdc1: smc 2 p1 err, cmd 1, RTO !! [ 6.043815] sunxi-mmc sdc1: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 6.420788] sndhdmi sndhdmi: sndhdmi <-> audiohdmi mapping ok [ 6.432513] ipip: IPv4 over IPv4 tunneling driver [ 6.441220] TCP: cubic registered [ 6.447387] Initializing XFRM netlink socket [ 6.455135] NET: Registered protocol family 10 [ 6.463893] mip6: Mobile IPv6 [ 6.469728] sit: IPv6 over IPv4 tunneling driver [ 6.478513] NET: Registered protocol family 17 [ 6.486217] NET: Registered protocol family 15 [ 6.493975] Bluetooth: RFCOMM TTY layer initialized [ 6.502206] Bluetooth: RFCOMM socket layer initialized [ 6.510824] Bluetooth: RFCOMM ver 1.11 [ 6.517577] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 6.526215] Bluetooth: BNEP filters: protocol multicast [ 6.534689] Bluetooth: BNEP socket layer initialized [ 6.542683] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 6.551884] Bluetooth: HIDP socket layer initialized [ 6.559704] 8021q: 802.1Q VLAN Support v1.8 [ 6.567551] Key type dns_resolver registered [ 6.574810] Key type ceph registered [ 6.582195] libceph: loaded (mon/osd proto 15/24) [ 6.590604] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 6.619261] Key type encrypted registered [ 6.627082] [DISP] boot_disp:0x405 [ 6.635148] [HDMI] cec support = 0 [ 6.641626] [DISP] disp_device_attached,line:101:attched ok, mgr0<-->device0, type=4 [ 6.655924] get usb_serial_number success from boot command line [ 6.663137] file system registered [ 6.674844] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 6.685331] android_usb gadget: Number of LUNs=3 [ 6.693295] lun0: LUN: removable file: (no medium) [ 6.701615] lun1: LUN: removable file: (no medium) [ 6.709785] lun2: LUN: removable file: (no medium) [ 6.718962] android_usb gadget: android_usb ready [ 6.727301] sunxi-rtc rtc: setting system clock to 2010-01-01 00:00:11 UTC (1262304011) [ 6.743248] ALSA device list: [ 6.749653] #0: audiocodec [ 6.756093] #1: sndhdmi [ 6.762844] Freeing unused kernel memory: 296K Loading, please wait... starting version 229 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.27.1 [/sbin/fsck.ext4 (1) -- /dev/mmcblk0p2] fsck.ext4 -f -y -C0 /dev/mmcblk0p2 e2fsck 1.42.13 (17-May-2015) Pass 1: Checking inodes, blocks, and sizes [01]BPI-ROOT: |= | 1.3% [01]BPI-ROOT: |= / 2.5% [02][01]BPI-ROOT: |== - 3.8% [02][01]BPI-ROOT: |=== \ 5.1% [02][01]BPI-ROOT: |==== | 6.4% [02][01]BPI-ROOT: |==== / 7.6% [02][01]BPI-ROOT: |===== - 8.9% [02][01]BPI-ROOT: |====== \ 10.2% [02][01]BPI-ROOT: |====== | 11.5% [02][01]BPI-ROOT: |======= / 12.7% [02][01]BPI-ROOT: |========= - 15.3% [02][01]BPI-ROOT: |========= \ 16.5% [02][01]BPI-ROOT: |========== | 17.8% [02][01]BPI-ROOT: |=========== / 19.1% [02][01]BPI-ROOT: |=========== - 20.4% [02][01]BPI-ROOT: |============ \ 21.6% [02][01]BPI-ROOT: |============= | 22.9% [02][01]BPI-ROOT: |============== / 24.2% [02][01]BPI-ROOT: |============== - 25.5% [02][01]BPI-ROOT: |=============== \ 26.7% [01]BPI-ROOT: |================ | 29.3% [02][01]BPI-ROOT: |================= / 30.5% [02][01]BPI-ROOT: |================== - 31.8% [02][01]BPI-ROOT: |=================== \ 33.1% [02][01]BPI-ROOT: |=================== | 34.4% [02][01]BPI-ROOT: |==================== / 35.6% [01]BPI-ROOT: |===================== - 36.9% [02][01]BPI-ROOT: |===================== \ 38.2% [02][01]BPI-ROOT: |====================== | 39.5% [02][01]BPI-ROOT: |======================= / 40.7% [02][01]BPI-ROOT: |======================== - 42.0% [02][01]BPI-ROOT: |======================== \ 43.3% [02][01]BPI-ROOT: |========================= | 44.5% [02][01]BPI-ROOT: |========================== / 45.8% [02][01]BPI-ROOT: |========================== - 47.1% [02][01]BPI-ROOT: |=========================== \ 48.4% [02][01]BPI-ROOT: |============================ | 49.6% [02][01]BPI-ROOT: |============================= / 50.9% [02][01]BPI-ROOT: |============================= - 52.2% [02][01]BPI-ROOT: |============================== \ 53.5% [02][01]BPI-ROOT: |=============================== | 54.7% [02][01]BPI-ROOT: |=============================== / 56.0% [01]BPI-ROOT: |================================ - 57.3% [02][01]BPI-ROOT: |================================= \ 58.5% [02][01]BPI-ROOT: |================================= | 59.8% [02][01]BPI-ROOT: |================================== / 61.1% [02][01]BPI-ROOT: |=================================== - 62.4% [01]BPI-ROOT: |==================================== \ 63.6% [02][01]BPI-ROOT: |==================================== | 64.9% [02][01]BPI-ROOT: |===================================== / 66.2% [02][01]BPI-ROOT: |====================================== - 67.5% [02][01]BPI-ROOT: |======================================= \ 70.0% [02][01] [02]Pass 2: Checking directory structure [01]BPI-ROOT: |======================================= | 70.1% [02][01]BPI-ROOT: |======================================== / 70.7% [02][01]BPI-ROOT: |======================================== - 71.2% [02][01]BPI-ROOT: |======================================== \ 71.9% [02][01]BPI-ROOT: |========================================= | 72.6% [02][01]BPI-ROOT: |========================================= / 73.2% [02][01]BPI-ROOT: |========================================= - 73.9% [02][01]BPI-ROOT: |========================================== \ 74.6% [02][01]BPI-ROOT: |========================================== | 75.2% [01]BPI-ROOT: |========================================== / 75.9% [02][01]BPI-ROOT: |=========================================== - 76.4% [02][01]BPI-ROOT: |=========================================== \ 77.0% [01]BPI-ROOT: |=========================================== | 77.6% [02][01]BPI-ROOT: |============================================ / 78.2% [02][01]BPI-ROOT: |============================================ - 78.8% [02][01]BPI-ROOT: |============================================ \ 79.5% [02][01]BPI-ROOT: |============================================= | 80.2% [02][01]BPI-ROOT: |============================================= / 80.9% [02][01]BPI-ROOT: |============================================== - 81.5% [02][01]BPI-ROOT: |============================================== \ 82.2% [02][01]BPI-ROOT: |============================================== | 82.8% [02][01]BPI-ROOT: |=============================================== / 83.5% [02][01]BPI-ROOT: |=============================================== - 84.1% [02][01]BPI-ROOT: |=============================================== \ 84.6% [02][01]BPI-ROOT: |================================================ | 85.2% [02][01]BPI-ROOT: |================================================ / 85.7% [02][01]BPI-ROOT: |================================================ - 86.4% [02][01]BPI-ROOT: |================================================= \ 87.0% [02][01]BPI-ROOT: |================================================= | 87.7% [02][01]BPI-ROOT: |================================================= / 88.3% [02][01]BPI-ROOT: |================================================== - 89.0% [02][01]BPI-ROOT: |================================================== \ 89.6% [02][01]BPI-ROOT: |================================================== | 89.9% [01]BPI-ROOT: |================================================== / 90.0% [02][01] [02]Pass 3: Checking directory connectivity Pass 4: Checking reference counts [01]BPI-ROOT: |==================================================== - 92.2% [02][01]BPI-ROOT: |===================================================== \ 93.9% [02][01] [02]Pass 5: Checking group summary information [01]BPI-ROOT: |===================================================== | 95.1% [02][01]BPI-ROOT: |======================================================= / 98.7% [02][01]BPI-ROOT: |========================================================| 100.0% [02][01] [02]BPI-ROOT: 91541/444400 files (0.2% non-contiguous), 487064/1776384 blocks fsck exited with status code 1 done. [ 20.028055] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. run-init: /init: No such file or directory Target filesystem doesn't have requested /init. [ 20.693891] systemd[1]: System time before build time, advancing clock. [ 20.761799] ip_tables: (C) 2000-2006 Netfilter Core Team [ 20.812257] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 20.847200] systemd[1]: Detected architecture arm. Welcome to [1B][1mDebian GNU/Linux 9 (stretch)[1B][0m! [ 20.881849] systemd[1]: Set hostname to . [ 21.495479] systemd[1]: Listening on Journal Socket (/dev/log). [[1B][0;32m OK [1B][0m] Listening on Journal Socket (/dev/log). [ 21.531049] systemd[1]: Listening on udev Control Socket. [[1B][0;32m OK [1B][0m] Listening on udev Control Socket. [ 21.561452] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [[1B][0;32m OK [1B][0m] Set up automount Arbitrary Executab…rmats File System Automount Point. [ 21.600693] systemd[1]: Listening on Syslog Socket. [[1B][0;32m OK [1B][0m] Listening on Syslog Socket. [ 21.631019] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [[1B][0;32m OK [1B][0m] Listening on /dev/initctl Compatibility Named Pipe. [ 21.661119] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[1B][0;32m OK [1B][0m] Started Dispatch Password Requests to Console Directory Watch. [ 21.701412] systemd[1]: Created slice System Slice. [[1B][0;32m OK [1B][0m] Created slice System Slice. [ 21.733945] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 21.761442] systemd[1]: Created slice system-getty.slice. [[1B][0;32m OK [1B][0m] Created slice system-getty.slice. [ 21.790629] systemd[1]: dev-hugepages.mount: Couldn't determine result for ConditionVirtualization=!private-users, assuming failed: No such file or directory [ 21.814261] systemd[1]: Created slice User and Session Slice. [[1B][0;32m OK [1B][0m] Created slice User and Session Slice. [ 21.850910] systemd[1]: Listening on Journal Socket. [[1B][0;32m OK [1B][0m] Listening on Journal Socket. [ 21.884111] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st…ce nodes for the current kernel... [ 21.923896] systemd[1]: Starting Journal Service... Starting Journal Service... [ 21.958071] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 21.996194] systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... [ 22.030679] systemd[1]: Listening on fsck to fsckd communication Socket. [[1B][0;32m OK [1B][0m] Listening on fsck to fsckd communication Socket. [ 22.070743] systemd[1]: Listening on udev Kernel Socket. [[1B][0;32m OK [1B][0m] Listening on udev Kernel Socket. [ 22.100460] systemd[1]: Reached target Remote File Systems. [[1B][0;32m OK [1B][0m] Reached target Remote File Systems. [ 22.134288] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 22.176958] systemd[1]: Starting Set the console keyboard layout... Starting Set the console keyboard layout... [ 22.211536] systemd[1]: Created slice system-serial\x2dgetty.slice. [[1B][0;32m OK [1B][0m] Created slice system-serial\x2dgetty.slice. [ 22.250601] systemd[1]: Reached target Slices. [[1B][0;32m OK [1B][0m] Reached target Slices. [ 22.284072] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 22.321023] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[1B][0;32m OK [1B][0m] Started Forward Password Requests to Wall Directory Watch. [ 22.360492] systemd[1]: Reached target Paths. [[1B][0;32m OK [1B][0m] Reached target Paths. [ 22.390479] systemd[1]: Reached target Encrypted Volumes. [[1B][0;32m OK [1B][0m] Reached target Encrypted Volumes. [ 22.428985] systemd[1]: Mounted Debug File System. [[1B][0;32m OK [1B][0m] Mounted Debug File System. [ 22.460639] systemd[1]: Mounted POSIX Message Queue File System. [[1B][0;32m OK [1B][0m] Mounted POSIX Message Queue File System. [ 22.491102] systemd[1]: Started Journal Service. [[1B][0;32m OK [1B][0m] Started Journal Service. [[1B][0;32m OK [1B][0m] Started Create list of required sta…vice nodes for the current kernel. [[1B][0;32m OK [1B][0m] Started Load Kernel Modules. [[1B][0;32m OK [1B][0m] Started Restore / save the current clock. [ 22.593005] EXT4-fs (mmcblk0p2): re-mounted. Opts: commit=600,errors=remount-ro Mounting Configuration File System... Mounting FUSE Control File System... Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev... [[1B][0;32m OK [1B][0m] Mounted FUSE Control File System. [[1B][0;32m OK [1B][0m] Mounted Configuration File System. [[1B][0;32m OK [1B][0m] Started Set the console keyboard layout. [[1B][0;32m OK [1B][0m] Started Remount Root and Kernel File Systems. [[1B][0;32m OK [1B][0m] Started Apply Kernel Variables. [[1B][0;32m OK [1B][0m] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... Activating swap /var/swap... Starting udev Coldplug all Devices... [[1B][0;32m OK [1B][0m] Reached target Local File Systems (Pre). Mounting /tmp... [[1B][0;32m OK [1B][0m] Mounted /tmp. [ 23.024987] Adding 131068k swap on /var/swap. Priority:-1 extents:2 across:229372k SS [[1B][0;32m OK [1B][0m] Started Load/Save Random Seed. [[1B][0;32m OK [1B][0m] Activated swap /var/swap. [[1B][0;32m OK [1B][0m] Started udev Kernel Device Manager. [[1B][0;32m OK [1B][0m] Reached target Swap. [[1B][0;32m OK [1B][0m] Started Entropy daemon using the HAVEGE algorithm. [[1B][0;32m OK [1B][0m] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... [[1B][0;32m OK [1B][0m] Started Set console font and keymap. [ 23.358122] systemd-journald[1300]: Received request to flush runtime journal from PID 1 [[1B][0;32m OK [1B][0m] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [[1B][0;32m OK [1B][0m] Started Create Volatile Files and Directories. [[1B][0;32m OK [1B][0m] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [[1B][0;32m OK [1B][0m] Started Update UTMP about System Boot/Shutdown. [[1B][0;32m OK [1B][0m] Started udev Coldplug all Devices. [[1B][0;32m OK [1B][0m] Reached target System Initialization. [[1B][0;32m OK [1B][0m] Listening on lircd.socket. [[1B][0;32m OK [1B][0m] Listening on D-Bus System Message Bus Socket. [[1B][0;32m OK [1B][0m] Reached target Sockets. [[1B][0;32m OK [1B][0m] Started Daily Cleanup of Temporary Directories. [[1B][0;32m OK [1B][0m] Reached target Basic System. Starting Login Service... [[1B][0;32m OK [1B][0m] Started Regular background program processing daemon. [ 24.440017] sunxi_ss_alg_register()879 - crypto_register_ahash(md5) failed! return -22 [ 24.459867] sunxi_ss_probe()992 - sunxi_ss_alg_register() failed! return -22 [ 24.481336] ss: probe of ce failed with error -22 Starting LSB: Banana Pi init script... Starting lircd(8) initialization helper tool... [ 24.542990] [VFE]cci_init end Starting LSB: Load kernel modules needed to enable cpufreq scaling... Starting Save/Restore Sound Card State... [[1B][0;32m OK [1B][0m] Started Convert IR remotes button p…ses to mouse movements and clicks. [[1B][0;32m OK [1B][0m] Started D-Bus System Message Bus. [ 24.691390] [VFE]Welcome to Video Front End driver [ 24.733962] [VFE]csi0 probe end! [ 24.748667] [VFE]csi1 probe end! [ 24.762361] [VFE]csi_init end [ 24.775856] [VFE]sunxi_isp_platform_register end [ 24.793146] [VFE]mipi_init end [ 24.805928] [VFE]flash_init end [ 24.821098] [VFE]pdev->id = 0 [ 24.833444] [VFE]dev->cci_sel = 0 [ 24.845780] [VFE]dev->csi_sel = 0 [ 24.858128] [VFE]dev->mipi_sel = 0 [ 24.870580] [VFE]dev->isp_sel = 0 [ 24.882583] [VFE_WARN]fetch csi0_dev0_power_en from device_tree failed [ 24.898105] [VFE_WARN]fetch csi0_dev0_flash_en from device_tree failed [ 24.913132] [VFE_WARN]fetch csi0_dev0_flash_mode from device_tree failed [ 24.928148] [VFE_WARN]fetch csi0_dev0_flvdd from device_tree failed [ 24.942600] [VFE_WARN]fetch csi0_dev0_flvdd_vol from device_tree failed [ 24.957426] [VFE_WARN]fetch csi0_dev0_af_pwdn from device_tree failed [ 24.977391] [VFE]vfe_init end [ 24.988479] [VFE]probe_work_handle start! [ 25.010615] [VFE]vfe_runtime_resume [ 25.035779] [VFE]..........................vfe clk open!....................... [ 25.051858] [VFE]v4l2 subdev register input_num = 0 [ 25.064803] [VFE]vfe sensor detect start! input_num = 0 [ 25.073772] [VFE]Find sensor name is "ov5640", i2c address is 78, type is "YUV" ! [ 25.085262] [VFE]Sub device register "ov5640" i2c_addr = 0x78 start! [ 25.135286] [OV5640@lex]init_sensor - frame_rate: 0, max_win_size: 11 [ 25.146926] [OV5640@lex]sensor_probe - frame_rate: 0 [ 25.147137] usbcore: registered new interface driver option [ 25.147198] usbserial: USB Serial support registered for GSM modem (1-port) [ 25.175922] [VFE]registered sensor subdev is OK! [ 25.184261] [VFE]Check sensor! [ 25.209833] [OV5640@lex]CSI_SUBDEV_PWR_ON! [ 25.220103] [VFE]mclk on [ 25.300078] [OV5640@lex]sensor_init: 0x0 [ 25.310108] sunxi_i2c_do_xfer()902 - [i2c4] incomplete xfer (status: 0x20, dev addr: 0x3c) [ 25.322362] [VFE_DEV_I2C_ERR]cci_read_a16_d8 error! slave = 0x3c, addr = 0x300a, value = 0x 0 [ 25.335328] sunxi_i2c_do_xfer()902 - [i2c4] incomplete xfer (status: 0x20, dev addr: 0x3c) [ 25.350942] [VFE_DEV_I2C_ERR]cci_read_a16_d8 error! slave = 0x3c, addr = 0x300a, value = 0x 0 [ 25.364245] sunxi_i2c_do_xfer()902 - [i2c4] incomplete xfer (status: 0x20, dev addr: 0x3c) [ 25.380399] [VFE_DEV_I2C_ERR]cci_read_a16_d8 error! slave = 0x3c, addr = 0x300a, value = 0x 0 ov5640 sensor read retry=2 [ 25.399816] [OV5640@lex]error at sensor_detect [ 25.408617] [OV5640@lex]chip found is not an target chip. [ 25.418457] [OV5640@lex]CSI_SUBDEV_PWR_OFF! [ 25.427087] [VFE]mclk off [ 25.473376] [VFE]vfe sensor subdev unregister! [ 25.482419] [OV5640@lex]sensor_remove ov5640 sd = dfa27dc0! [ 25.496324] [VFE]Sub device register "ov5640" failed! [ 25.506101] [VFE_ERR]vfe sensor register check error at input_num = 0 [ 25.517294] [VFE]V4L2 device registered as (null) [ 25.526900] [VFE]vfe_runtime_suspend [ 25.534892] [VFE]..........................vfe clk close!....................... [ 25.553736] [VFE]probe_work_handle end! Starting System Logging Service... [[1B][0;32m OK [1B][0m] Started Handle events from IR remotes decoded by lircd(8). [[1B][0;32m OK [1B][0m] Started Save/Restore Sound Card [ 25.771828] libphy: gmac0: probed State. [ 25.810245] sunxi-gmac gmac0 eth0: eth0: Type(6) PHY ID 001cc915 at 1 IRQ poll (gmac0-0:01) [ 25.835116] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [[1B][0;32m OK [1B][0m] Found device /dev/ttyS0. [[1B][0;32m OK [1B][0m] Started System Logging Service. [[1B][0;32m OK [1B][0m] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [[1B][0;32m OK [1B][0m] Reached target Sound Card. [[1B][0;32m OK [1B][0m] Started LSB: Load kernel modules needed to enable cpufreq scaling. [[1B][0;32m OK [1B][0m] Started Login Service. Starting Load/Save RF Kill Switch Status... Starting LSB: set CPUFreq kernel parameters... [ 27.793493] sunxi-bt bt: set block: 0 [ 27.804091] sunxi-bt bt: check bluetooth bt_power voltage: 3300000 [ 27.820655] sunxi-bt bt: check bluetooth io_regulator voltage: 3300000 [[1B][0;32m OK [1B][0m] Started LSB: set CPUFreq kernel parameters. [[1B][0;32m OK [1B][0m] Started Load/Save RF Kill Switch Status. Starting LSB: Set sysfs variables from /etc/sysfs.conf... [[1B][0;32m OK [1B][0m] Started LSB: Set sysfs variables from /etc/sysfs.conf. [[1B][0;32m OK [1B][0m] Started lircd(8) initialization helper tool. [ 30.534911] ctp_fetch_sysconfig_para: ctp_power_io is invalid. [ 30.546135] axp22_dcdc1: Failed to create debugfs directory [ 30.610279] i2c-core: driver [ft5x_ts] using legacy suspend method [ 30.621745] i2c-core: driver [ft5x_ts] using legacy resume method [ 30.633327] sunxi_i2c_do_xfer()902 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x38) [ 30.660249] sunxi_i2c_do_xfer()902 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x38) [ 30.673929] ctp_detect:I2C connection might be something wrong ! [ 30.810324] libphy: gmac0-0:01 - Link is Up - 1000/Full [ 30.820755] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 32.216143] dhd_module_init: in [ 32.224309] ======== bcm_wlan_set_plat_data ======== [ 32.234274] dhd_wifi_platform_load: Enter [ 32.243080] Power-up adapter 'DHD generic adapter' [ 32.252886] wifi_platform_set_power = 1 [ 32.261525] ======== PULL WL_REG_ON HIGH! ======== [ 32.272903] sunxi-wlan wlan: check wlan wlan_power voltage: 3300000 [ 32.284805] sunxi-wlan wlan: check wlan io_regulator voltage: 3300000 [ 32.610147] wifi_platform_bus_enumerate device present 1 [ 32.627089] sunxi-wlan wlan: bus_index: 1 [ 32.642395] ======== Card detection to detect SDIO card! ======== [[1B][0m[1B][0;31m* [1B][0m] (1 of 2) A start job is running for…network interfaces (11s / 5min 2s) [1B][K[[1B][0;1;31m*[1B][0m[1B][0;31m* [1B][0m] (1 of 2) A start job is running for…network interfaces (12s / 5min 2s) [1B][K[[1B][0;31m*[1B][0;1;31m*[1B][0m[1B][0;31m* [1B][0m] (1 of 2) A start job is running for…network interfaces (13s / 5min 2s)[ 34.660134] failed to power up DHD generic adapter, 3 retry left [ 34.687338] wifi_platform_set_power = 0 [ 34.695877] ======== PULL WL_REG_ON LOW! ======== [ 34.705930] wifi_platform_bus_enumerate device present 0 [ 34.715900] sunxi-wlan wlan: bus_index: 1 [ 34.724340] ======== Card detection to remove SDIO card! ======== [ 34.735149] wifi_platform_set_power = 1 [ 34.743403] ======== PULL WL_REG_ON HIGH! ======== [ 34.754116] sunxi-wlan wlan: check wlan wlan_power voltage: 3300000 [ 34.765512] sunxi-wlan wlan: check wlan io_regulator voltage: 3300000 [ 34.780063] sunxi-mmc sdc1: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 34.794562] sunxi-mmc sdc1: no vqmmc,Check if there is regulator [ 34.820049] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 34.850840] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !! [ 34.861728] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !! [ 34.871731] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 34.889139] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 34.905902] sunxi-mmc sdc1: smc 2 p1 err, cmd 8, RTO !! [ 34.916162] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 34.940336] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) [ 34.952394] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 34.964214] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 34.977240] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) [ 35.094621] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 35.109517] sunxi-mmc sdc1: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 35.124564] wifi_platform_bus_enumerate device present 1 [ 35.124803] sunxi-mmc sdc1: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B [ 35.126502] mmc2: new high speed SDIO card at address 0001 [ 35.159989] sunxi-wlan wlan: bus_index: 1 [ 35.168634] ======== Card detection to detect SDIO card! ======== [ 35.195897] bcmsdh_register: register client driver [ 35.205900] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter [1B][K[ [1B][0;31m*[1B][0;1;31m*[1B][0m[1B][0;31m* [1B][0m] (2 of 2) A start job is [ 35.215592] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter running for…ana Pi init script[ 35.226753] bus num (host idx)=2, slot num (rca)=1 (13s / 5min 2s)[ 35.238964] found adapter info 'DHD generic adapter' [ 35.250396] dhdsdio_probe : no mutex held. set lock [ 35.260058] F1 signature read @0x18000000=0x1541a9a6 [ 35.271994] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x1 pkg:0x4 [ 35.284265] DHD: dongle ram size is set to 524288(orig 524288) at 0x0 [ 35.295779] dhd_conf_set_chiprev: chip=0xa9a6, chiprev=1 [ 35.306004] dhd_conf_set_conf_path_by_nv_path: config_path=/lib/firmware/ap6212/config.txt [1B][K[ [1B][0;31m*[1B][0;1;31m*[1B][0m[1B][0;31m* [1B][0m] (2 of 2) A start job is running for…ana Pi init script (14s / 5min 2s) [1B][K[ [1B][0;31m*[1B][0;1;31m*[1B][0m[1B][0;31m*[1B][0m] (2 of 2) A start job is running for…ana Pi init script (14s / 5min 2s) [1B][K[ [1B][0;31m*[1B][0;1;31m*[1B][0m] (1 of 2) A start job is running for…network interfaces (15s / 5min 2s) [1B][K[ [1B][0;31m*[1B][0m] (1 of 2) A start job is running for…network interfaces (16s / 5min 2s)[ 37.967584] dhd_conf_read_config: nv_by_chip_count=3 [ 37.977542] dhd_conf_read_config: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt [ 37.990088] dhd_conf_read_config: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt [ 38.002535] dhd_conf_read_config: chip=0x4345, chiprev=6, name=nvram_ap6255.txt [ 38.015986] wl_create_event_handler(): thread:wl_event_handler:6d1 started [ 38.015992] tsk Enter, tsk = 0xee6c14a0 [1B][K[ 38.036757] dhd_attach(): thread:dhd_watchdog_thread:6d2 started [ [1B][0;31m*[1B][0;1;31m*[1B][0m] (1 of 2) A start job is running for[ 38.047807] dhd_attach(): thread:dhd_dpc:6d3 started …network interfaces (16s / 5min 2s)[ 38.047818] dhd_dpc_thread: set dpc_cpucore 0 from config.txt [ 38.069648] dhd_attach(): thread:dhd_rxf:6d4 started [ 38.079479] dhd_deferred_work_init: work queue initialized [1B][K[ 38.090313] dhdsdio_probe_init: set use_rxchain 1 from config.txt Starting Load/Save RF Kill Switch Status... [ 38.109634] Dongle Host Driver, version 1.201.59.3 (r506368) [ 38.109634] Compiled in drivers/net/wireless/bcmdhd on Mar 13 2019 at 15:50:22 [ 38.133320] Register interface [wlan0] MAC: ac:83:f3:33:be:d4 [ 38.133320] [ 38.149559] dhd_prot_ioctl : bus is down. we have nothing to do [ 38.160203] dhd_txglom_enable: enable 0 [ 38.168331] dhd_bus_devreset: WLAN OFF DONE [ 38.177432] wifi_platform_set_power = 0 [ 38.185728] ======== PULL WL_REG_ON LOW! ======== [ 38.196366] dhdsdio_probe : the lock is released. [ 38.205739] dhd_module_init: Exit err=0 [ [1B][0;31m*[1B][0;1;31m*[1B][0m[1B][0;31m*[1B][0m] (1 of 3) A start job is running for…network interfaces (17s / 5min 2s) [1B][K[[1B][0;32m OK [1B][0m] Started LSB: Banana Pi init script. [[1B][0;32m OK [1B][0m] Started Load/Save RF Kill Switch Status. [[1B][0;32m OK [1B][0m] Started Raise network interfaces. [[1B][0;32m OK [1B][0m] Reached target Network. Starting OpenBSD Secure Shell server... Starting Permit User Sessions... [[1B][0;32m OK [1B][0m] Started Unattended Upgrades Shutdown. [[1B][0;32m OK [1B][0m] Started Flexible IR remote input/output application support. [[1B][0;32m OK [1B][0m] Started Forward LIRC button presses as uinput events. [[1B][0;32m OK [1B][0m] Reached target Network is Online. Starting LSB: Start NTP daemon... [ 41.706338] input: lircd-uinput as /devices/virtual/input/input5 Starting LSB: disk temperature monitoring daemon... Starting /etc/rc.local Compatibility... [[1B][0;32m OK [1B][0m] Started Daily apt download activities. [[1B][0;32m OK [1B][0m] Started Daily apt upgrade and clean activities. [[1B][0;32m OK [1B][0m] Reached target Timers. Starting LSB: Advanced IEEE 802.11 management daemon... [[1B][0;32m OK [1B][0m] Started OpenBSD Secure Shell server. [[1B][0;32m OK [1B][0m] Started Permit User Sessions. [[1B][0;32m OK [1B][0m] Started LSB: Advanced IEEE 802.11 management daemon. [[1B][0;32m OK [1B][0m] Started LSB: disk temperature monitoring daemon. [[1B][0;32m OK [1B][0m] Started LSB: Start NTP daemon. [ 42.205316] rc.local[1828]: My IP address is 10.24.1.164 [[1B][0;32m OK [1B][0m] Started /etc/rc.local Compatibility. [[1B][0;32m OK [1B][0m] Started Serial Getty on ttyS0. [[1B][0;32m OK [1B][0m] Started Getty on tty1. [[1B][0;32m OK [1B][0m] Reached target Login Prompts. [[1B][0;32m OK [1B][0m] Reached target Multi-User System. [[1B][0;32m OK [1B][0m] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [[1B][0;32m OK [1B][0m] Started Update UTMP about System Runlevel Changes. Debian GNU/Linux 9 bpi-iot-ros-ai ttyS0 bpi-iot-ros-ai login: