Jump to content

apristen

Members
  • Posts

    6
  • Joined

  • Last visited

Recent Profile Visitors

936 profile views
  1. Hi. First, thanks for Armbian! I compiled it from sources and all works fine on my Orange Pi Plus When I try Armbian with LCD monitor (HDMI) - it works well, but Youtube video playback (even 480p) very-very slow Is there any way to activate/install/etc. HW video acceleration on Armbian on Orange Pi Plus (Allwinner H3) for watch Youtube videos on LCD monitor ?
  2. [sOLVED] I compiled Armbian for wrong board: "orangepipcplus" instead of "orangepiplus". Thanks a lot for your support!
  3. Does that image support USB OTG and g_mass_storage? in this case it solves _all_ my problems a lot!
  4. UPD: Perhaps I found problem: I have Orange Pi+, not Orange Pi PC+ (looks similar) Are they different in Ethernet schematic?
  5. Many thanks for Armbian and fast reply, Igor! I just followed instructions from here: https://docs.armbian.com/Developer-Guide_Build-Preparation/ Build was fully automatic (thanks again!) and after some time I have image with: kernel 3.4.113 and Ubuntu 16.04.1 for "orangepipcplus" (selected from menu) All works fine, except Ethernet. I'll try buld from "download" section and test Ethernet on it, thanks. P.S. Actually all I need is: Ethernet at least 100 Mbit, USB OTG (device) with g_mass_storage support. Unfortunately default distribution has no g_mass_storage (usb gadget) support...
  6. Hi all. I build Armbian for "orangepipcplus" as described here: https://docs.armbian.com/Developer-Guide_Build-Preparation/ After build finished, I've got Armbian_5.24_Orangepipcplus_Ubuntu_xenial_3.4.113.img image, flash it to SD card, and my OPi starts well, thanks! All things that necessary for my work tasks - works fine: USB, USB OTG, WiFi, but... no Ethernet :-( When I plug Ethernet cable into my PC and OPi - no LED blinks at both sides (but Ethernet on PC 100% works, tested with Raspberry Pi, for example). In console kernel logs I see the following: [ **] A start job is running for Raise network interfaces (26s / 5min 6s) And OPi actually waits 5 minutes, but fails with: [FAILED] Failed to start Raise network interfaces. dmesg for gmac and eth0 is following: [ 11.323860] gmac0: probed [ 11.324213] gmac0 gmac0: eth0: eth0: PHY ID 00441400 at 0 IRQ poll (gmac0-0:00) [ 16.780250] ==> rtl8188e_iol_efuse_patch [ 17.062774] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 19.413458] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 21.640063] eth0: no IPv6 routers present [ 29.920044] wlan0: no IPv6 routers present ifconfig shows eth0, it's UP, I can set IP address manually, but I suggest problem is NOT in TCP/IP, but deeper... ethtool and mii-tool shows: root@orangepipcplus:~# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10Mb/s Duplex: Half Port: MII PHYAD: 0 Transceiver: external Auto-negotiation: on Link detected: no root@orangepipcplus:~# mii-tool eth0: no link Could you please advise - what to check next? what settings I should check in kernel config? in u-boot config? (cable works fine with another board, but with OrangePi I even see NO blinking LEDs on OPi's Ethernet socket, perhaps PHY chip Realtek 8211E is off somehow...) P.S. I need _any_ Ethernet working, (not exactly 1Gbps) Fast Ethernet 100Mbps - more than enough for my tasks. P.P.S. Did anyone test USB Ethernet adapter as a temporary solution? which model works fine?
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines