domoticity

Members
  • Content count

    13
  • Joined

  • Last visited

  1. Banana Pi M2 Berry

    Hy, Can you tell me which OS do you used in this M2 berry? Ubuntu or raspbian? Thanks
  2. Banana-pi m64 and access point

    Hy, I have found the Solution. Tested with a Banana pi m64 and the m2 Berry ( with AP6212 and driver BCMDHD). First : For HOSTAPD . If you are in Ubuntu, just do a apt-get install hostapd If you are in Debian, use the Second Method of this Link. Then, make the hostapd.conf An Example : interface=uap0 ssid=testPiAP hw_mode=g channel=11 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=badpassword wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP AP MODE : the msot important sudo nano /etc/modprobe.d/bcmdhd.conf. and write options bcmdhd op_mode=2 Reboot the Card. To see if the AP mode is ok : systool -m bcmdhd -v If you haven't the Systool sudo apt-get install sysfsutils And to launch hostapd sudo hostapd /etc/hostapd/hostapd.conf I hope i was understandable with my Bad English
  3. Bananapi M2 and Gigabit Ethernet

    Hello Someone can say me if the Transfert RAte is limited at 300mo or like the Bananapi m64 a true Gigabit. Thanks
  4. Hy When I do a Speedtest-cli with my Bananapi m1, I have 320mo for Download and 180mo for Upload. When I do with my Laptop I have 700mo for Download and 180mo for Upload. My os is Armbian. I have also a Bananapi M64 and with her I have the same results than my Laptop. Some one has an Idea? Thanks
  5. Banana-pi m64 and access point

    I understand ^^. One question please. I have looked for an 8812au chipset nano size and I have seen it Netgear a6100 Do you know it? Thank you
  6. Banana-pi m64 and access point

    Hy, i have a Notification which tell me you have aswered but i don't Manage to See your Post
  7. Banana-pi m64 and access point

    Hy me again So i have my Bananapi m1 and i have someone who give me an wifi adaptator : Edimax ew-7811un. He said me it's a 8812au. But when i do a lsmod i don't see 8812au but RTL 8192CU. I have seen in Internet that's i can complied Driver 8812au for this Adaptator,but it's for Raspberry. Can you help me for my Bananapi I know that you have given me a model of adaptator,but a nano adaptator is better for my Project If i don't have the choice,i will take it. armbian-config is very nice and helpfull.
  8. Banana-pi m64 and access point

    I wll tell you if it makes my happiness the Bananpi m1 lol. But she seems to be better than the m64, even if this last one seems to be powerfull. I will keep it for a Domotic box
  9. Banana-pi m64 and access point

    I just ordered a banana-pi m1, which can have mainline kernel. And I will take the usb wifi Adaptateur you suggest me. I have managed to do an Access Point and a lot of things with my raspberry 2 but it doesn't have Gigabit ethernet. Shame on her lol.
  10. Banana-pi m64 and access point

    Hy I haven't bought the Bananapi M64, it's my Employer. I will take another card with all your Recommendations. Thank you again
  11. Banana-pi m64 and access point

    Thanks anyway for your help what banana-pi would you advise me? The m2 or m2 +?Or another. I just need a WiFi chip and an ethernet Gigabit port and make access point.
  12. Banana-pi m64 and access point

    Hy thank you for your Answer. I have do : sudo modprobe bcmdhd op_mode=2 but always same thing : my ap wifi stays no visible.
  13. Hy Everybody. For my Work, I need an Access Point into the Bananapi M64. So I have followed this tutorial: https://www.awasu.com/weblog/bpi-gateway/wifi-access-point/ And more precisely: First, install the packages needed to compile: sudo apt-get install gcc git make sudo apt-get install libnl-3-dev libnl-genl-3-dev openssl libssl-dev pkg-config Then, get the source for hostapd: cd /tmp git clone git://w1.fi/srv/git/hostap.git Then, configure it: cd hostap/hostapd cp defconfig .config Edit .config and make sure that CONFIG_DRIVER_NL80211=y and CONFIG_LIBNL32=y are active i.e. not commented out. Then, compile and install it: make sudo cp hostapd /usr/sbin/ My /etc/hostapd/hostapd.conf: interface=wlan0 ssid=testPiAP hw_mode=g channel=11 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=badpassword wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP Copy the Code When I launch Hostapd I have : pi@bpi-iot-ros-ai:~$ sudo hostapd -B /etc/hostapd/hostapd.conf Configuration file: /etc/hostapd/hostapd.conf Using interface wlan0 with hwaddr 44:2c:05:ee:81:21 and ssid "testPiAP" wlan0: interface state UNINITIALIZED->ENABLED wlan0: AP-ENABLED But I don't see my access point wifi with my smartphone, laptop or another devices. Here my ifconfig and I can scan wifi network : [sudo] password for pi: eth0 Link encap:Ethernet HWaddr aa:c2:4f:16:ee:b8 inet addr:192.168.1.48 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:272 errors:0 dropped:0 overruns:0 frame:0 TX packets:99 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23758 (23.2 KiB) TX bytes:13132 (12.8 KiB) Interrupt:114 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:25 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2728 (2.6 KiB) TX bytes:2728 (2.6 KiB) wlan0 Link encap:Ethernet HWaddr 44:2c:05:ee:81:21 inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: fe80::462c:5ff:feee:8121/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:48 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:2232 (2.1 KiB I don't manage to see where I am wrong and it's been two Weeks I tried to find a solution. Help me please