GPIO problem using gpio-sunxi module on OrangePi ONE

[klaute]

Hello,

 

currently I am working on my Orange pi one system (Armbian Linux orangepione 3.4.113-sun8i #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 armv7l armv7l armv7l GNU/Linux)

to get my ILI9341-TFT display to work using the fb_ili9341 kernel module.

 

I have read a lot of documentation and the display works (using the fb_ili9341 module) attached to my cubeitruck (also running armbian).

I think that the problem is the GPIO- kernel module of the Orange PI one.

 

These are the output messages in the syslog file after "modprobe gpio-sunxi":

[  343.417378] gpio_pin_1(7) gpio_request
[  343.417817] gpio_pin_2(8) gpio_request
[  343.418095] gpio_pin_3(9) gpio_request
[  343.418489] gpio name is PA8, ret = 0
[  343.418885] gpio name is PA9, ret = 0
[  343.419213] get config err!
[  343.422568] gpio_sw: probe of gpio_sw.2 failed with error -12
[  343.422808] gpio_init finish with uesd 1

 

My script.fex file contain the following lines:

[gpio_para]
gpio_used = 1
gpio_num = 3
gpio_pin_0 = port:PA07<1><default><default><0>
gpio_pin_1 = port:PA08<1><default><default><0>
gpio_pin_2 = port:PA09<1><default><default><0>

 

[spi0]
spi_used = 1
spi_cs_bitmap = 1
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_cs0 = port:PC03<3><1><default><default>

And yes, the TFT display is connected to SPI0 and the DC, RST and LED lines are also correctly connected...

 

modprobe fbtft dma=1
modprobe fbtft_device custom name=fb_ili9341 buswidth=8 busnum=0 bgr=1 mode=0 speed=64000000 txbuflen=64 fps=25 gpios=reset:0,dc:1,led:2 rotate=0 debug=1

 

~# lsmod
Module                  Size  Used by
fb_ili9341              3432  0
fbtft_device           25082  0
fbtft                  24194  2 fb_ili9341,fbtft_device

And it semes to be that the fb_ili9341 driver has detected the display:

 

[  618.725172] fbtft_device:  SPI devices registered:
[  618.725209] fbtft_device:      spidev spi0.0 33000kHz 8 bits mode=0x00
[  618.725231] fbtft_device:  'fb' Platform devices registered:
[  618.725370] fbtft_device: Deleting spi0.0
[  618.726173] fbtft_device:  GPIOS used by 'fb_ili9341':
[  618.726199] fbtft_device:    'reset' = GPIO0
[  618.726216] fbtft_device:    'dc' = GPIO1
[  618.726233] fbtft_device:    'led' = GPIO2
[  618.726249] fbtft_device:  SPI devices registered:
[  618.726271] fbtft_device:      fb_ili9341 spi0.0 64000kHz 8 bits mode=0x00
[  618.747630] fb_ili9341 spi0.0: fbtft_request_gpios: 'reset' = GPIO0
[  618.747677] fb_ili9341 spi0.0: fbtft_request_gpios: 'dc' = GPIO1
[  618.747714] fb_ili9341 spi0.0: fbtft_request_gpios: 'led' = GPIO2
[  619.115261] graphics fb8: fb_ili9341 frame buffer, 240x320, 150 KiB video memory, 0 KiB DMA buffer memory, fps=25, spi0.0 at 64 MHz

 

Does anyone got an idea what the problem could be?

 

Thanks!

 

Regards

Kai