Learnincurve Posted June 13, 2017 Share Posted June 13, 2017 Hi, On my Clearfog base, I have one bootable SDHC card that I made some time ago, using Title: Armbian 5.25 Clearfogbase Debian Jessie next Kernel: Linux 4.9.7 Build date: 02.02.2017 I can't remember, but think that I flashed the card from Linux using dd bs=1M What I do remember was having some trouble back then, flashing a card that would boot and remember several attempts, using several different images. I also remember that the board dip switches were in the wrong positions as delivered from the factory and that my first attempts failed because of that. Having sorted that out and using the image described above, the system now boots (mostly) using this card, but I did want to try using a stable image now, so have been trying to flash an identical sd card using one of the current, stable images. I have now been forced over to using a Windows 10 machine, so am trying the recommended, 7zip, then Etcher approach. I clean format the card, then point Etcher at the image and card. I have tried this approach with: Armbian_5.27_Clearfogbase_Ubuntu_xenial_default_4.4.70.img Armbian_5.27_Clearfogbase_Debian_jessie_next_4.11.3.img Armbian_5.27_Clearfogbase_Debian_jessie_default_4.4.70.img All of them are giving the same boot problem: __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01 (Apr 07 2017 - 21:42:19) Marvell version: 2015_T1.0p11 Board: A38x-Customer-Board-1 SoC: MV88F6828 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1600 [MHz] L2 @ 800 [MHz] TClock @ 250 [MHz] DDR3 @ 800 [MHz] DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB MMC: mv_sdh: 0 *** Warning - bad CRC, using default environment PCI-e 0: Detected No Link. PCI-e 1: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x3fed4000:0x3ff9831c BSS: 0x3ffefd5c Stack: 0x3f9c3f20 Heap: 0x3f9c4000:0x3fed4000 U-Boot Environment: 0x000f0000:0x00100000 (MMC) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | SGMII | In-Band | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 Hit any key to stop autoboot: 0 Trying to boot from MMC 1565 bytes read in 68 ms (22.5 KiB/s) ## Executing script at 03000000 Boot script loaded from mmc Unknown command 'load' - try 'help' Unknown command 'load' - try 'help' Unknown command 'load' - try 'help' Unknown command 'load' - try 'help' Bad Linux ARM zImage magic! Trying to boot from USB (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** ## Executing script at 03000000 Boot script loaded from usb Unknown command 'load' - try 'help' Unknown command 'load' - try 'help' Unknown command 'load' - try 'help' Unknown command 'load' - try 'help' Bad Linux ARM zImage magic! Default boot sequence failed - falling back to TFTP Using egiga0 device TFTP from server 10.4.50.38; our IP address is 10.4.50.170 Filename 'uImage'. Load address: 0x2000000 Loading: T T T T T T T T T T Retry count exceeded; starting again Using egiga0 device TFTP from server 10.4.50.38; our IP address is 10.4.50.170 Filename 'armada-388-clearfog.dtb'. Load address: 0x2000000 Loading: T T T T T T T T T T Retry count exceeded; starting again Bad Linux ARM zImage magic! Marvell>> Please can someone suggest what I am doing wrong? Best regards Marius Link to comment Share on other sites More sharing options...
zador.blood.stained Posted June 13, 2017 Share Posted June 13, 2017 Please use 5.25 images from https://dl.armbian.com/clearfogbase/archive/ or wait for the 5.30 release. I'm not sure why we have 5.27 images for some boards, they shouldn't be there. Link to comment Share on other sites More sharing options...
Learnincurve Posted June 13, 2017 Author Share Posted June 13, 2017 Perfect! That worked! Thank you for replying. BR. --Marius-- Link to comment Share on other sites More sharing options...
Recommended Posts