All Activity

This stream auto-updates     

  1. Today
  2. query

    OPi Zero and DS18B20 1-Wire Problem

    Thank you. I think I've added those lines in the modules.conf after having this problem in the beginning, but I'll remove them and let you know how it goes.
  3. martinayotte

    OPi Zero and DS18B20 1-Wire Problem

    Yes, remove them from modules.conf, but don't add them in armbianEnv.txt since you've already have things properly set there : overlays=usbhost2 usbhost3 i2c0 i2c1 w1-gpio param_w1_pin=PA10 param_w1_pin_int_pullup=0 This will make the module loading properly with the proper pin PA10.
  4. query

    OPi Zero and DS18B20 1-Wire Problem

    Thanks for the reply @martinayotte So, I should remove everything in /etc/modules-load.d/modules.conf and place them accordingly into /boot/armbianEnv.txt ? I need the i2c-dev for another sensor I have. How do I do this exactly? Thanks in advance.
  5. martinayotte

    OPi Zero and DS18B20 1-Wire Problem

    You should not placed i2c-dev, w1-gpio and w1-therm inside /etc/modules-load.d/modules.conf, you should leave the DeviceTree doing the load of modules itself, otherwise it won't take in account the pins definitions you've provided in /boot/armbianEnv.txt
  6. Mabrafs

    Read/Write to SPI flash?

    Is it possible to connect that with VeePN service? Now I am using VeePN just in order to receive access to blocked content like websites, games, media, music, some streaming TV apps like Netflix, etc. But, of course, if you need VPN for serious tasks you have to use more serious approach with SD cards.
  7. guidol

    armbianmonitor error

    I did test a fresh compiled armbian-stretch mainline without any problems - much cooler and mine does show 4.94V-4.97V not 4.76V login as: root root@192.168.6.120's password: ____ ____ _ | __ ) __ _ _ __ __ _ _ __ __ _ | _ \(_) | _ \ / _` | '_ \ / _` | '_ \ / _` | | |_) | | | |_) | (_| | | | | (_| | | | | (_| | | __/| | |____/ \__,_|_| |_|\__,_|_| |_|\__,_| |_| |_| Welcome to ARMBIAN 5.83 user-built Debian GNU/Linux 9 (stretch) 4.19.36-sunxi package bsp-kernel[5.83] u-boot[5.83] dtb[5.83] firmware[5.83] config[5.83] System load: 1.64 0.44 0.15 Up time: 0 min Memory usage: 5 % of 997MB IP: 192.168.6.120 CPU temp: 35°C Usage of /: 13% of 7.2G [ General system configuration (beta): armbian-config ] Last login: Thu Apr 25 22:05:22 2019 from 192.168.6.17 root@bpi-m1(192.168.6.120):~# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU PMIC DC-IN C.St. 22:25:11: 960MHz 1.53 50% 24% 23% 0% 2% 0% 33.8°C 37.5°C 4.97V 0/6 22:25:16: 960MHz 1.49 7% 6% 0% 0% 0% 0% 33.7°C 37.2°C 4.96V 0/6 22:25:22: 960MHz 1.33 11% 10% 0% 0% 0% 0% 33.8°C 37.1°C 4.97V 0/6 22:25:28: 528MHz 1.31 6% 6% 0% 0% 0% 0% 33.7°C 37.0°C 4.97V 0/6 22:25:33: 960MHz 1.20 10% 10% 0% 0% 0% 0% 33.4°C 37.1°C 4.94V 0/6 22:25:39: 528MHz 1.10 7% 6% 0% 0% 0% 0% 33.7°C 36.7°C 4.97V 0/6 22:25:44: 528MHz 1.02 11% 10% 0% 0% 0% 0% 33.8°C 36.9°C 4.97V 0/6 22:25:50: 960MHz 0.93 8% 7% 0% 0% 0% 0% 33.7°C 36.8°C 4.97V 0/6 22:25:55: 960MHz 1.02 11% 11% 0% 0% 0% 0% 33.6°C 36.7°C 4.97V 0/6 22:26:01: 960MHz 0.94 23% 15% 8% 0% 0% 0% 34.1°C 36.9°C 4.96V 0/6 22:26:06: 528MHz 0.86 14% 13% 0% 0% 0% 0% 33.7°C 36.8°C 4.97V 0/6 22:26:12: 960MHz 0.88 7% 6% 0% 0% 0% 0% 33.6°C 36.8°C 4.96V 0/6 22:26:17: 960MHz 0.81 14% 13% 0% 0% 0% 0% 33.5°C 36.6°C 4.97V 0/6 22:26:23: 528MHz 0.74 10% 9% 0% 0% 0% 0% 33.7°C 36.8°C 4.97V 0/6 and with conservative-governor: Time CPU load %cpu %sys %usr %nice %io %irq CPU PMIC DC-IN C.St. 22:58:46: 528MHz 0.43 13% 8% 4% 0% 0% 0% 31.8°C 33.6°C 4.98V 0/6 22:58:51: 528MHz 0.39 7% 7% 0% 0% 0% 0% 31.5°C 33.5°C 4.98V 0/6 22:58:57: 528MHz 0.44 11% 11% 0% 0% 0% 0% 31.4°C 33.5°C 4.98V 0/6 22:59:02: 528MHz 0.49 7% 7% 0% 0% 0% 0% 31.4°C 33.3°C 4.97V 0/6 22:59:08: 528MHz 0.45 12% 11% 0% 0% 0% 0% 31.7°C 33.7°C 4.98V 0/6 22:59:14: 528MHz 0.49 7% 7% 0% 0% 0% 0% 31.5°C 33.6°C 4.98V 0/6 22:59:19: 528MHz 0.57 12% 11% 0% 0% 0% 0% 31.2°C 33.3°C 4.98V 0/6 22:59:25: 528MHz 0.52 7% 7% 0% 0% 0% 0% 31.4°C 33.7°C 4.98V 0/6 22:59:31: 528MHz 0.48 11% 11% 0% 0% 0% 0% 31.5°C 33.4°C 4.98V 0/6 22:59:36: 528MHz 0.44 7% 7% 0% 0% 0% 0% 31.3°C 33.5°C 4.98V 0/6 22:59:43: 528MHz 0.40 9% 8% 0% 0% 0% 0% 31.4°C 33.4°C 4.98V 0/6 22:59:48: 528MHz 0.37 12% 11% 0% 0% 0% 0% 31.5°C 33.7°C 4.97V 0/6 22:59:54: 528MHz 0.47 7% 7% 0% 0% 0% 0% 31.2°C 33.4°C 4.97V 0/6 22:59:59: 528MHz 0.43 12% 11% 0% 0% 0% 0% 31.3°C 33.6°C 4.98V 0/6 So maybe the bugs are alread fixed in the newer versions?
  8. Hi everyone, What I want to do is to use a DS18B20 through 1-Wire to read temperature on an OPi Zero. The sensor seems to be detected by the board (I see the file under /sys/bus/w1/devices/28-something), and then it disappears randomly after a reboot or a power cycle. (file goes away and obviously I can't get any readings). Then it starts working randomly again after an indefinite amount of reboots. I'm having this problem for a while now, and it's driving me absolutely crazy. This one here on the picture is the sensor I'm using. I have attached a 4.7K Ohm resistor between the VCC and Digital cables, and attached to OPi Zero as follows: VCC -> BCM pin 2 (5V, I've also tried with 3.3V) Digital -> BCM pin 26 (PA10) Ground -> BCM pin 25 After that, I've edited my /boot/armbianEnv.txt and it looks like this now: verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 i2c0 i2c1 w1-gpio param_w1_pin=PA10 param_w1_pin_int_pullup=0 rootdev=UUID=374d182b-7b9e-4570-b7c5-519a1eb837a7 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u0x2537:0x1066:u,0x2537:0x1068:u0x2537:0x1066:u,0x2537:0x1068:u Also adapted the /etc/default/cpufrequtils file as follows: # WARNING: this file will be replaced on board support package (linux-root-...) upgrade ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive And the /etc/modules-load.d/modules.conf: g_serial i2c-dev w1-gpio w1-therm So, after all these modifications, I do a reboot and I can see the w1_gpio and w1_therm modules loaded in the output from lsmod, and I can see the device in /sys/bus/w1/devices/28-something I can get my readings and everything works properly. Then, I do a reboot. Here is where I get super confused, because it seems like there's no systematic error in the wiring or the kernel modules being loaded as far as I can see. But, the device disappears after the reboot. Sometimes it will get detected again, without me doing any changes in the configuration. I've already tried two of the same sensor, but it doesn't seem to make any difference, same problem still. I've also put the armbianmonitor output to the post. Looking desparately for some ideas to help me debug this problem. Thanks!
  9. Igor

    armbianmonitor error

    Hmm, from some strange reason, your temperature is not read ... I can't reproduce this error on none of my A20 boards, which are on my desk. None of them is M1, but they are very similar. All work fine. Thanks and welcome to join.
  10. vivekpk

    Couldn't start AP(host) mode in Banana Pi M2+

    ok, i will check with this image
  11. Tested right now and it works as expected. Logs: http://ix.io/1Hc0 1. Debian Stretch CLI image https://dl.armbian.com/bananapim2plus/Debian_stretch_next.7z 2. Creating user, running update (apt update and apt upgrade) 3. armbian-config -> network -> Hotspot 4. Connect with a mobile, no problem, running speedtest, speed as expected 5. Reboot 5. Connect with a mobile, no problem, running speedtest, speed as expected
  12. I give up. I thank everyone for help.I have too little knowledge to solve this.
  13. lzb

    armbianmonitor error

    Sorry for grave digging, but I have the same error messages in BananaPi M1: root@bananapi:~# armbianmonitor -m >> armmon.log /usr/bin/armbianmonitor: line 385: read: read error: 0: Connection timed out /usr/bin/armbianmonitor: line 386: [: 43.5: integer expression expected /usr/bin/armbianmonitor: line 385: read: read error: 0: Connection timed out /usr/bin/armbianmonitor: line 386: [: 43.3: integer expression expected /usr/bin/armbianmonitor: line 385: read: read error: 0: Connection timed out /usr/bin/armbianmonitor: line 386: [: 43.2: integer expression expected /usr/bin/armbianmonitor: line 385: read: read error: 0: Connection timed out /usr/bin/armbianmonitor: line 386: [: 43.2: integer expression expected /usr/bin/armbianmonitor: line 385: read: read error: 0: Connection timed out /usr/bin/armbianmonitor: line 386: [: 43.4: integer expression expected /usr/bin/armbianmonitor: line 385: read: read error: 0: Connection timed out /usr/bin/armbianmonitor: line 386: [: 43.4: integer expression expected *snip* root@bananapi:~# dmesg | tail [74843.472544] thermal thermal_zone0: failed to read out thermal zone (-110) [74961.592838] thermal thermal_zone0: failed to read out thermal zone (-110) [80058.430841] thermal thermal_zone0: failed to read out thermal zone (-110) [81036.963935] thermal thermal_zone0: failed to read out thermal zone (-110) [83488.688937] thermal thermal_zone0: failed to read out thermal zone (-110) [84273.576483] thermal thermal_zone0: failed to read out thermal zone (-110) [85252.109538] thermal thermal_zone0: failed to read out thermal zone (-110) [85553.122760] thermal thermal_zone0: failed to read out thermal zone (-110) [85660.618355] thermal thermal_zone0: failed to read out thermal zone (-110) [86133.835726] thermal thermal_zone0: failed to read out thermal zone (-110) root@bananapi:~# armbianmonitor -u System diagnosis information will now be uploaded to http://ix.io/1HbP Please post the URL in the forum where you've been asked for. Not that I care about those errors, but maybe it can be pushed to fix some bug. I'm running armbianmonitor >> file because my BananaPi setup has small uptime (like, it freezes and I need to restart it - that's another story). PS Keep up the good work on Armbian!
  14. vivekpk

    Couldn't start AP(host) mode in Banana Pi M2+

    no its not working from armbian-config
  15. langerma

    Ethernet not working on SOPINE module

    okay...as i wanted to reinstall the boards i am going to test it this weekend
  16. Haha - SE's worries. I get paid if she waists my time or not.
  17. I followed all the help I could find in the forum as well as on the net. None however was specific to the Nanopi Neo Plus 2, so I thought I'd ask.
  18. Is it working when you use armbian-config way? network -> armbian-config?
  19. Igor

    Ethernet not working on SOPINE module

    When someone will confirm that its working, I will push update to the repository. Then, apt upgrade will make a difference. And manual u-boot update (from nand-sata-install menu) when important change is there.
  20. Because its a mess with those wireless chips. There are different versions of them and each needs different firmware settings ... Which one you have in mind?
  21. ilchenko Evgeny

    Orangepi 3 h6 allwiner chip

    Hi, friends. I noticed such an interesting feature. I have a 100 megabit Internet connection and on windows PC with uTorrent have a rate of about 10mb/sec download but if run download on Transmittion-deamon i have a maximum of 5mb/sec i.e. only half speed. Why?
  22. Hi i am trying to create a hotspot using Network Manager in my banana pi nmcli con add type wifi ifname wlan0 con-name Hostspot autoconnect yes ssid pducontroller nmcli con modify Hostspot 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared nmcli con modify Hostspot wifi-sec.key-mgmt wpa-psk nmcli con modify Hostspot wifi-sec.psk "verylongpassword" nmcli con up Hostspot But when I type nmcli con up Hostspot gives me an output Error: Connection activation failed. here is my system diagnosis information link
  23. just use the searchbox, right hand, top corner and look for: AP6212
  24. Petee

    Armbian for Amlogic S9xxx kernel 4.1x (>= ver 5.55)

    Did a nightly build update to the second TV Box here (TX9 Pro - Octocore, 3Gb, 1Gb NIC) and it is working well. Only thing though when logging in to the computer see the following stuff relating to RockPro64 changing from S912 standard release logo when logging in. ____ _ ____ __ _ _ | _ \ ___ ___| | _| _ \ _ __ ___ / /_ | || | | |_) / _ \ / __| |/ / |_) | '__/ _ \ | '_ \| || |_ | _ < (_) | (__| <| __/| | | (_) | | (_) |__ _| |_| \_\___/ \___|_|\_\_| |_| \___/ \___/ |_| Welcome to ARMBIAN 5.82.190423 nightly Ubuntu 18.04.2 LTS 5.1.0-rc1-aml-s912 System load: 0.00 0.00 0.00 Up time: 8:33 hours Memory usage: 10 % of 2840MB Zram usage: 1 % of 1023Mb IP: 192.168.244.150 CPU temp: 44°C Usage of /: 14% of 29G Last login: Thu Apr 25 00:25:58 2019 from 192.168.244.232 Running a couple of automation pieces of software, docker and mono (CPU sucker)..it is hardly working...headless Found the configuration file for the MOTD here: /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=rockpro64 BOARD_NAME="RockPro 64" BOARDFAMILY=rockchip64 VERSION=5.82.190423 LINUXFAMILY=rockchip64 BRANCH=default ARCH=arm64 IMAGE_TYPE=nightly BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image /etc/update-motd.d/10-armbian-header printf '\nWelcome to \e[0;91mARMBIAN\x1B[0m %s %s %s %s\n' "$VERSION $IMAGE_TYPE $PRETTY_NAME $KERNELID"
  25. mrsufgi

    RockPi 4b 'board bring up'

    Don't, it doesn't work (tried it myself). I also tried all available images (5.79 with 5.0.0 kernel), non of them works.
  26. I've escalated my problem - I guess the SE will select another board. For curiosity sake, does anybody have any idea(s) about why the WIFI firmware is not working in linux kernel 4.19.36 (but in 4.19.20)?
  1. Load more activity