My name is Gabriel and I am a new person in the community.
After installing ARMBIAN (Armbian_5.91_Clearfogbase_Debian_stretch_default_4.14.135) with the Mini PCI Express Marvel 88SE9215, I got a problem with my Clearfog Pro-A1 revision-2.1. It did not work properly like 88SE9215 did not show me my disks. My Idea is to deploy my NAS server with OMV.
I tried to compile the kernel so many times with different modules like SATA, PATA, and AHCI but it did not work also. I guess that my u-boot is not setup properly because I was reading a couple post about it and it’s working to everyone.
Someone can give me a favor pls and tell me your ideas to try to solve that problem
Clearfog Pro-A1 revision-2.1 + Marvel 88SE9215
in Marvell mvebu
Posted
Hi everyone,
My name is Gabriel and I am a new person in the community.
After installing ARMBIAN (Armbian_5.91_Clearfogbase_Debian_stretch_default_4.14.135) with the Mini PCI Express Marvel 88SE9215, I got a problem with my Clearfog Pro-A1 revision-2.1. It did not work properly like 88SE9215 did not show me my disks. My Idea is to deploy my NAS server with OMV.
I tried to compile the kernel so many times with different modules like SATA, PATA, and AHCI but it did not work also. I guess that my u-boot is not setup properly because I was reading a couple post about it and it’s working to everyone.
Someone can give me a favor pls and tell me your ideas to try to solve that problem
Thanks.
Logs:
Armbianmonitor: http://ix.io/201C
root@clearfogbase:~# lspci
00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6828 (rev 0a)
00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6828 (rev 0a)
02:00.0 SATA controller: Marvell Technology Group Ltd. Device 9215 (rev 11)
root@clearfogbase:~# lspci -nv
00:02.0 0604: 11ab:6828 (rev 0a) (prog-if 00 [Normal decode])
Flags: fast devsel
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [100] Advanced Error Reporting
00:03.0 0604: 11ab:6828 (rev 0a) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00010000-00010fff
Memory behind bridge: e0000000-e00fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [100] Advanced Error Reporting
02:00.0 0106: 1b4b:9215 (rev 11) (prog-if 01 [AHCI 1.0])
Subsystem: 1b4b:9215
Flags: bus master, fast devsel, latency 0, IRQ 53
I/O ports at 10020
I/O ports at 10030
I/O ports at 10028
I/O ports at 10034
I/O ports at 10000
Memory at e0040000 (32-bit, non-prefetchable)
Expansion ROM at e0000000
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [70] Express Legacy Endpoint, MSI 00
Capabilities: [e0] SATA HBA v0.0
Capabilities: [100] Advanced Error Reporting
Kernel driver in use: ahci
Booting from Clearfog
U-Boot SPL 2018.01-02337-gdc4398fdb8 (May 14 2018 - 19:03:16)
High speed PHY - Version: 2.0
Detected Device ID 6828
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 3 | SATA0 |
| 1 | 0 | SGMII1 |
| 2 | 5 | PCIe1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
--------------------------------
PCIe, Idx 1: detected no link
PCIe, Idx 2: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.29.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Trying to boot from SPI
U-Boot 2018.01-02337-gdc4398fdb8 (May 14 2018 - 19:03:16 +0200), Build: jenkins-u-boot-clearfog-model=pro,variant=spi-10
SoC: MV88F6828-?? (a) at 1600 MHz
DRAM: 1 GiB (800 MHz, 32-bit, ECC not enabled)
MMC: mv_sdh: 0
SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB
Model: SolidRun Clearfog
Board: SolidRun ClearFog Pro
SCSI: SATA link 0 timeout.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
Net: eth1: ethernet@70000, eth2: ethernet@30000, eth3: ethernet@34000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0(part 0) is current device
** No partition table - mmc 0 **
starting USB...
USB0: Register 2000120 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: device type unknown
... is now current device
** Bad device usb 0 **
** Bad device usb 0 **
scanning bus for devices...
Found 0 device(s).