[Orangepi 3 h6 allwiner chip]

15.07.2021 в 00:50, maigonis сказал:

Я прочитал руководство пользователя и снова открыл его. Я нигде не нашел то, что вы упомянули, только то, что он может питаться обоими способами. Но я считаю, что OTG может быть не лучшим вариантом для его питания. Я не электрик, поэтому, если он не загружается при питании от входа бочкообразного джека, то я, скорее всего, избавлюсь от него.

Hello! I must apologize for misleading you. Again looked at the manual, there really is no warning about the limitations of OTG. In my old head something was confused. I read this information somewhere else.
Sincerely, Viktor Chekasin.

[Orangepi 3 h6 allwiner chip]

Hello! The OPI3 manufacturer in the manual directly warns not to be supplied through OTG. Too thin conductors! Alternatively, check these electrical chains and restore. If it does not help, then the AXP805 is destroyed. You can, of course, replace it if there are skills. OS is not exactly here.
Sincerely, Viktor Chekasin.
P.S. Sorry, this is a machine forever from Russian into English.

[Orangepi 3 h6 allwiner chip]

Hello everyone! I did a simple test of the USB3 ports. USB2 flash drives work great. USB3 flash drives are not detected. Although DBT has indications for USB3.
However, my knowledge is limited, I do not know how to edit it.
Best regards, Viktor Vasilievich.

[Orangepi 3 h6 allwiner chip]

Hey! In my opinion, Opi3 is not a very good motherboard for use as a personal computer. There are inconsistencies with Linux (Video, PCIe).
I have not been able to find a good Android image for this board so far.
Good luck with your development!

[Orangepi 3 h6 allwiner chip]

6 hours ago, Francisco said:

Hi!

 

Not sure if this is the right place to post this, but...

 

I just bought 10 Orange Pi 3 and none has a regular functioning ethernet. The LEDs go on as expected, the graphic network setup tool shows a DHCP address for a second (or even less) then it goes away, along with the LEDs. After a few seconds, the cycle comes on again and again.

 

Do I have a bad lot?  I've tried almost all available images, including the android that came in the ESSD memory, they all had the same behaviour.

 

Thanks!

Francisco

Hi, Francisco!

The situation is strange .... I have OPi 3 Opi and Win +. There were no problems with the network. WiFi, Ethernet, BT - everything works like a clock.
I can assume that the problem is outside, say, a ban on access to the network.
Sincerely, Victor.

[Orange Pi One Plus H6 no sound HDMI]

Hello everyone! I have Orange Pi 3 and Armbian 5.4.28. Having repeatedly experimented on different displays, I found out that, most likely, with each boot of HDMI, the Orange Pi driver polls the display. If the answer comes and it is correct, then there is HDMI sound, otherwise - no. Some older displays are not detected in this way. But you can try to reload the old display while running Orange Pi. Most likely, a sound will appear. When using the HDMI-VGA adapter, I did not receive sound on the adapter’s audio connector. This also speaks in favor of the fact that the HDMI driver is "looking" for the correct device in order to direct the sound there. To this, I can only add that on my Orange Pi 3 Android board ALWAYS outputs audio to HDMI, including through the HDMI-VGA adapter.
which unfortunately, my qualifications do not allow me to fix this yet. But it is also fixable, what my years! (I am 70 years old)

[Orangepi 3 h6 allwiner chip]

On 24.05.2020 at 15:30, maxpyeha said:

Пожалуйста, объясните, как я могу выводить видео через RCA (аудио выход и AV на плате)?

Видимо, для Armbian (и Ubuntu) RCA не включен, я пробовал специальный "родной" кабель с 4-х контактным джеком.  Это прекрасно работает для Android. Поэтому причина неисправности точно в Armbian. Буду искать...

[Orangepi 3 h6 allwiner chip]

On 30.03.2019 at 23:45, NicoD said:

Может кто-нибудь еще проверить напряжение на USB, пожалуйста? Я вижу очень низкое напряжение от 4,5 В до 4 В максимально.
Я использую кабель OPi и блок питания 4A от моего NanoPi M4. Я хотел бы знать, если это моя установка. Спасибо.
PS
При более высоком входном напряжении 5,3 В (против 5,1 В) у меня 4,75 В на холостом ходу и 4,5 В на максимуме.

Orange Pi developers do not recommend using USB-OTG to power the board, too thin conductors. Moreover, there are current limits from the USB host. This is all in the documentation.

[Orange Pi One Plus H6 no sound HDMI]

Hello!
I am Russian. I use machine translation. Sorry if not very clear.
Regarding Orange Pi 3 and audio output via HDMI, I found the following:
For Armbian. If you start the board not by a button, but by applying voltage, then there is HDMI sound, otherwise - there is no sound through HDMI. How to treat it, I do not know.