MacBreaker

Yes, that was the information what I was missing..
 
I was thinking about that, but I didn't find that information.
 
Thanks for sharing your DTB, but i'm on 5.10.60.
I froze the kernel and changed my DTB, all is fine now!
 
@guidol
 
Liebe Grüsse aus Bishkek/Kirgistan wo ich zeitweise außer in Haiger/Hessen lebe..

As I read
http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=3399
it seems to be possible.
At the URL is a information how to change the .DTB for the OPi Zero to use the USB-OTG as USB-HOST
 
You have to find the right usb-port (usb@1c19000) in the .DTB/.DTS for the OPi One
 
DTB to DTS decompile
dtc -I dtb -O dts /boot/dtb/sun8i-h3-orangepi-one.dtb -o /boot/dtb/sun8i-h3-orangepi-one.dts
 
EDIT
change in the .DTS:
change the line:
                        dr_mode = "otg";
to                     dr_mode = "host";
in the section
usb@1c19000
 
from: usb@1c19000 { compatible = "allwinner,sun8i-h3-musb"; reg = <0x1c19000 0x400>; clocks = <0x03 0x20>; resets = <0x03 0x11>; interrupts = <0x00 0x47 0x04>; interrupt-names = "mc"; phys = <0x10 0x00>; phy-names = "usb"; extcon = <0x10 0x00>; dr_mode = "otg"; status = "okay"; phandle = <0x48>; }; to: usb@1c19000 { compatible = "allwinner,sun8i-h3-musb"; reg = <0x1c19000 0x400>; clocks = <0x03 0x20>; resets = <0x03 0x11>; interrupts = <0x00 0x47 0x04>; interrupt-names = "mc"; phys = <0x10 0x00>; phy-names = "usb"; extcon = <0x10 0x00>; dr_mode = "host"; status = "okay"; phandle = <0x48>; };  
 
DTS to DTB compile
dtc -I dts -O dtb /boot/dtb/sun8i-h3-orangepi-one.dts -o /boot/dtb/sun8i-h3-orangepi-one.dtb
 
then REBOOT
 
As attachment the new compiled version (when you have the same kernel as I 5.15.4
 
@MacBreaker
PS: Liebe Gruesse nach Hessen - vor 6 Jahren habe ich in Babenhausen bei Frankfurt/Darmstadt gewohnt - nun in der Tuerkei....
sun8i-h3-orangepi-one.dtb

@orangepie14
 

..about power outages..
 
I had this problem years argo also.
I run a server (Orange Pi PC) 24/7 in a area with a lot of "power outages".

I prevent this with a board like this: Double 18650 Lithium-Batterie Schild V8 Mobile Power bank
 
 
 
You have only to connect it between your power source and you Pi.
 
That's all..
 
Markus

@jslav
 
about video*
 
take a look here:
 
check the active modules and blacklist them...
 

Hello Igor,
since years i seed Armbian torrents but i noticed that i'm running out of space.
My hdd was 248GB till now...
 
Looking for further information and saw in the first post is written 512GB.
Maybe you can add a big ">NOTE!< since Version 20.05.xx you need 512GB free space".
 
Also after you installed transmission by ->Software ->Softy ->Transmission you get asked to seed Armbian torrents.
Here a screen:
 

 
You have to change the number from 80GB to 512GB.
 
Just my thinking about this..
 
Markus

To enable I2S is easy. See this thread:
 
 
Have you tried the search function up on the right side?
 
You can do it on your Orange Pi PC Plus the same way Guido did it on Nanopi Neo.
 

Hi Tido,
 
thanks for clarification of root or root privileges.
i didn't know this, sorry.
 
I will read the README.md and start over again on the weekend.
 
 
Ich hoffe...

Hey, this will not work..
 
Have you seen the data sheet of the Rock64?
 
There is no I2S on the Pi-2 Bus (pinheader) where you connected the HiFiBerry DAC from your RPi.
You can use jumper wire to connect it with P5 but you need a overlay to activate I2S.
 
 

OK, i'm prepaired with my 500GB HDD on a Cubietruck right now...

OK, i'm prepaired with my 500GB HDD on a Cubietruck right now...

First you have to enable analog audio...
 
sudo armbian-config ->System ->Hardware -> mark analog-codec ... sudo reboot If you need /etc/asound.conf , you have to create by you own...

Hello Igor,
since years i seed Armbian torrents but i noticed that i'm running out of space.
My hdd was 248GB till now...
 
Looking for further information and saw in the first post is written 512GB.
Maybe you can add a big ">NOTE!< since Version 20.05.xx you need 512GB free space".
 
Also after you installed transmission by ->Software ->Softy ->Transmission you get asked to seed Armbian torrents.
Here a screen:
 

 
You have to change the number from 80GB to 512GB.
 
Just my thinking about this..
 
Markus

Yes, and you all can be proud of this...

@gounthar
 
how i did it with my OPZero:
 
Enable w1-gpio
 
add param_w1_pin=PA10 to armbianEnv.txt and connect your DS18B20 like these.. +------------------------------------------------+ | OPi Zero GPIO Pin | 18B20 | Widerstand | |------------------------|---------|-------------| |Pin 17 3.3V | braun | VCC |-|4,7kOhm|-¬ | |Pin 26 1-wire | blau | Data |------------ | |Pin 9 GND | schwarz | GND | | +------------------------------------------------+ Its working fine :-)
 
 

I had also had a lot power outages.
 
I bougt a "Bms 18650 Batterie Schild V3 Expansion Board"
(https://de.aliexpress.com/item/32996504176.html?spm=a2g0s.9042311.0.0.1ec64c4da6MXpj) with a 18650 Batterie, and the problen was solved.
 

 
 

I would suggest the orange pi zero plus with extension board.
 
H5 Prozessor
512 MB RAM
3x USB 2.0
Gigabit Ethernet
Onboard WiFi
SPI Flash

Runs for me very reliable for over 2 years under Debian Stretch.
No thermal problems... running without exclosure on myside...
 
I use it for: websites/webservice, pihole, openvpn, oscam server ... below 50 degrees Celsius.
 
It's around 19,45€ including delivery to Europe (where i'm living).
 
https://de.aliexpress.com/item/32851197198.html?spm=a2g0x.12010612.8148356.9.1be67144SgjLnC
 

Ok, i've canged back to 4.14.69, all work how expected...
 
 
...armbian-config is a great tool.
 
Thanks Igor