Wu Min

Members
  • Content Count

    2
  • Joined

  • Last visited

 Content Type 

Forums

Member Map

Store

Crowdfunding

Applications

Calendar

Everything posted by Wu Min

  1. Thank‘s for your reply. My version is V5, which confirms that EMMC has been installed on the backplane.
  2. when I used the command "nand-sata-install" ,then i select The first one, install Armbian from the SD card to the Built in emmc, After step-by-step execution, I will prompt poweroff. Then I remove the SD card and prepare to start from EMMC. However, the following error prompt appears. I cannot enter the system from EMMC normally,Please help me, thank you TIM-1.0 WTMI-devel-18.12.1-e6bb176 WTMI: system early-init CPU VDD voltage default value: 1.155V NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2) NOTICE: BL1: Built : 16:23:10, May 21 2019 NOTICE: BL1: Booting BL2 NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2) NOTICE: BL2: Built : 16:23:11, May 21 2019 NOTICE: BL1: Booting BL31 NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2) NOTICE: BL31: Built : 16:2 U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100) Model: Marvell Armada 3720 Community Board ESPRESSOBin CPU 1000 [MHz] L2 800 [MHz] TClock 200 [MHz] DDR 800 [MHz] DRAM: 1 GiB Comphy chip #0: Comphy-0: USB3 5 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: ncq led only pmp fbss pio slum part sxs PCIE-0: Link down MMC: sdhci@d0000: 0, sdhci@d8000: 1 Loading Environment from SPI Flash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB OK Model: Marvell Armada 3720 Community Board ESPRESSOBin Net: eth0: neta@30000 [PRIME] Hit any key to stop autoboot: 0 starting USB... USB0: Register 2000104 NbrPorts 2 Starting the controller USB XHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found / ** Bad device usb 0 ** ## Executing script at 06d00000 Wrong image format for "source" command /boot/ ** Bad device usb 0 ** ## Executing script at 06d00000 Wrong image format for "source" command scanning bus for devices... Device 0: unknown device / ** Bad device scsi 0 ** ## Executing script at 06d00000 Wrong image format for "source" command /boot/ ** Bad device scsi 0 ** ## Executing script at 06d00000 Wrong image format for "source" command / ** File not found /boot.scr ** ## Executing script at 06d00000 Wrong image format for "source" command /boot/ 1119 bytes read in 15 ms (72.3 KiB/s) ## Executing script at 06d00000 240 bytes read in 4 ms (58.6 KiB/s) Card did not respond to voltage select! ** Bad device mmc 0 ** Card did not respond to voltage select! ** Bad device mmc 0 ** Card did not respond to voltage select! ** Bad device mmc 0 ** Card did not respond to voltage select! ** Bad device mmc 0 ** Bad Linux ARM64 Image magic! / Card did not respond to voltage select! ** Bad device mmc 0 ** ## Executing script at 06d00000 Wrong image format for "source" command /boot/ Card did not respond to voltage select! ** Bad device mmc 0 ** ## Executing script at 06d00000 Wrong image format for "source" command Marvell>>