-
Posts
20 -
Joined
-
Last visited
Content Type
Forums
Store
Crowdfunding
Applications
Events
Raffles
Community Map
Posts posted by Anatolii Kraskovskiy
-
-
проблема решена (какая-то странная)
Я заменил монитор
изменил разрешение
but this is not a solution to the question
firmware of other manufacturers are working properly !!!!!!!!
-
h5@orangepizeroplus2:~$ sudo tvservice -p
[sudo] password for h5:
sudo: tvservice: command not found
-
armbian_5.58.180813
все порты работают, я проверил, написал сценарий на python, ttyS2 и ttyUSB0
установить WiringPiH5 - рабочий
после повторных обновлений появились все режимы отображения
but anyway, with an overload or when you turn on you have to pull the cable in time hdmi
рус - но всё равно , при перегрузки или при включении надо вовремя передёрнуть кабель
-
H3 has script.bin
H5 ?
-
/boot/armbianEnv.txt
verbosity = 1
console = both
overlay_prefix = sun50i-h5overlays = analog-codec uart2 usbhost2 usbhost3
rootdev = UUID = 24769c95-0527-419b-9d00-51dbb2e34929
rootfstype = ext4
usbstoragequirks = 0x2537: 0x1066: u, 0x2537: 0x1068: u
Спасибо за совет
не работал
-
I understand that these are not stable versions
I do not know how to work with the Linux kernel
on this and I ask the experts how to solve this or that problem
forums have been set up for this
but now on the merits:
if there is a chance to help - tell me
1 armbian_5.58.180813
When you start , each time you have to switch the cable hdmi
there is no sound for hdmi
can not install Gambas 3
2 Armbian_5.42_Orangepizeroplus2-h5_Debian_stretch_dev_4.16.0.img
on debian 8 end 9 , ubuntu 14 and 16 - gambas - is established
dut the mouse and keyboard do not work.
I want to apply this
-
Armbian_5.42_Orangepizeroplus2-h5_Debian_stretch_dev_4.16.0.img
keyboard input does not work
no mouse control
management only through pyttu
monitor (xdmi) works, the image is displayed
how to make the keyboard and mouse work?
-
У меня такая же проблема
armbian_5.58.180813after Запуск ядра ... Экран станет синим, нет сигнала
os на emmc
установить минимальный рабочий стол - это принципиально
- если вы установите все программное обеспечение - 1366 * 768 - нет
- если вы обновляете - 1366 * 768 - нет
если на момент запуска ядра ... отсоединить кабель HDMI и подключиться через 3-4 секунды, рабочий стол запущен, изображение
-
armbian_5.58.180813
TIME ] Timed out waiting for device dev-ttyGS0.device.
[DEPEND] Dependency failed for Serial Getty on ttyGS0.desktop installed
after Starting kernel ... The screen turns blue, there is no signal
if at the moment Starting kernel ... disconnect the cable HDMI , and connect after 3-4 seconds , the desktop is running ,image is
after reboot - image is
after shutdown - no image
-
Someone can give instructions on how to work with the firmware of Armbian.
1 connection of HDMI after loading
2 start the desktop -
Well now it's clear what's the matter - there is no support for hdmi, the first time it's turned on. The omission on the part of the developers, about this or where it is not said, is very sad
through putty went into the config, but how to enable hdmi?
-
3 minutes ago, rusatch said:
Толян, у меня такая же плата. Несколько дней назад ставил последний доступный образ, все работало и до сих пор работает.
-------------------
@Анатолий Красковский, у меня такая же доска. Несколько дней он работает с последним изображением.
put the image of the card, I'll try, it can work
-
Dietpi works, but there you need to additionally put everything, + a start script that I do not need to solve my task, on the day I need a 64-bit mini computer with EMMC
raspberry has no EMMC, and it is larger in size
firmware that was not downloaded from https://www.armbian.com/orange-pi-zero-2-h5/
-
All the firmware that I found on the Internet for Orange pi Zero plus 2, except Armbian, - work. Posted on the site Armbian for Orange pi Zero plus 2, neither the server nor the desktop - do not load, just start as in the photo and then the blue screen. Previously, the firmwares were laid out old, nightly, now this is not (or I do not know how to see them), this is bad
-
Orange Pc plas works without problems
-
I have several cards, all with a recording speed of more than 10, specially selected, tested on Orange Pc plas, as well as checked for ubuntu, debian, dietpi. power supply 5 V 5 A, we check oscilloscope, there are no dips and no noise
-
no control, waiting for up to 3 minutes
-
all firmware for Orange pi Zero plus 2 (H5) - do not start.
loading stops as b on the photo of
On 13.03.2018 at 01:32, paolobasile said:Я использовал обе версии, но никто не работает. Изображение появляется, но остается черным. Важно сказать, что если я не буду вводить какую-либо SD-карту, плата начнет Android (из памяти emmc). Как я могу полностью отформатировать эту память? Я думаю, что это проблема, я могу использовать версию ubuntu, которая работает с оранжевой страницы
after that the screen turns blue, and the download stops
debian , ubuntu , dietpi - are working
But they can not be transferred to EMMC
Going crazy with Orange Pi Zero Plus2 H5
in Allwinner sunxi
Posted
Всем спасибо за участие
После опробования нескольких сборок, можно сделать вывод - armbian как всегда на высоте
Конечно есть недостатки. Одни - сними можно смерится, другие - подробность и доступность документации - желательно устранять
Методики "борьбы" за живучесть, чёткой нет. Linux довольно сложная система, а систематизированная литература не так много (в принципе я не нашёл) (кроме выбора SD карточки и блока питания), а то что есть, не очень соответствует .. Чувствуется, что при создании системы "веселились" все кому не лень (если только хватало мозгов)
А теперь конкретно по плате и ос к ней
Orange Pi Zero Plus2 H5 очень привлекательная плата (просто то что надо для малых систем контроля и управления), даже малый объем оперативной памяти (по сравнению с смартфонами) не смущает. На ней практически есть всё что надо и самое главное emmc. Что опробовано - работа с ком портом, работа с микрофоном и опознаванием речи.
Из всех сборок на момент лета 2018 года наиболее подходящая 5.38 stabile Debian 9 и 5.38 stabile Ubuntu 14
Причина, почему я задавал вопросы (нет): Нет инструкций, что бы и как подключить, и как обращаться с программным обеспечением
Почему не было изображения - не запускался рабочий стол - не корректные установки дисплея рабочего стола - автоматическое определение, не все мониторы и телевизоры автоматически могут определятся. Почему не работала клавиатура и мышка - все завязано на идентификацию по дисплею, а так как идентификация не прошла корректно клавиатура и мыш не заработали