Search the Community
Showing results for tags 'nanopi-r6c'.
-
My audio volume was very very low, and very annoyingly I had to boost to 200% 300% which had the problem that the volume buttons were not working properly. You just cant see anything above 100% unless you go into the control panel. Now when it comes to audio I'm the village idiot, but I found a proper solution I think. After some experimentation I found that the module "module-cli-protocol-unix" ( #20 in my case) can be amplified with pactl set-sink-input-volume 20 10db Now YMMV depending on your attached hardware, so change the 10db to whatever suits your situation. After that I made it permanent by adding it to the /etc/pulse/default.pa like this: # Default volume amplification set-sink-input-volume 20 10db Yay!
-
I am unable to play files over SMB, but I can't seem to figure out what the problem is exactly. From what I can tell it *seems* ffmpeg is compiled without networking support, at least this is what smplayer was complaining about: [ffmpeg] Protocol not found. Make sure ffmpeg/Libav is compiled with networking support. Failed to open smb://192.168.1.1/transmission/myfile.mkv. Exiting... (Errors when loading file) But when I look at the ffmpeg switches it was compiled with: --enable-libsmbclient and seems to be present. Now I'm a complete linux n00b, does anyone have an idea ? -
It seems a package is missing from the Armbian 23.8 Bookworm CLI that results in this error. I encountered an add-apt-repository: traceback error. To fix it just run: sudo apt install python3-launchpadlib
-
What Works: - USB2 and USB3 - PCIe2 - GMAC - eMMC on HS200 mode - Cpufreq - User and maskrom buttons Dmesg Output: https://paste.armbian.com/onelomofit You can download them from Rolling releases section on https://www.armbian.com/nanopi-r6s/ page. Images include devicetrees for R6S and R6C. If you have R6C, you must change the devicetree from armbianEnv.txt.
-
As you can see the WAN-port/NIC registers fine with a label from the nanopi-r6c device tree $ grep fe1c0000 /boot/dtb/rockchip/rk3588s-nanopi-r6c.dtb grep: /boot/dtb/rockchip/rk3588s-nanopi-r6c.dtb: binary file matches dmesg: dmesg | grep fe1c0000 [ 7.287277] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID [ 7.287373] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 7.287377] rk_gmac-dwmac fe1c0000.ethernet: DWMAC4/5 [ 7.287381] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported [ 7.287385] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported [ 7.287388] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported [ 7.287391] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported [ 7.287423] rk_gmac-dwmac fe1c0000.ethernet: TSO supported [ 7.287426] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 7.287430] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2) [ 7.287433] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled [ 7.287437] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width However the LAN-port does not have such a label in dmesg output. [ 7.932846] pci 0003:31:00.0: [10ec:8125] type 00 class 0x020000 [ 7.932902] pci 0003:31:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 7.932905] pci 0003:31:00.0: reg 0x10: [io size 0x0100] [ 7.932958] pci 0003:31:00.0: reg 0x18: [mem 0x00000000-0x0000ffff 64bit] [ 7.932993] pci 0003:31:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit] [ 7.933301] pci 0003:31:00.0: supports D1 D2 [ 7.933303] pci 0003:31:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 7.948845] pci 0003:31:00.0: BAR 2: assigned [mem 0xf3200000-0xf320ffff 64bit] [ 7.948873] pci 0003:31:00.0: BAR 4: assigned [mem 0xf3210000-0xf3213fff 64bit] [ 7.948899] pci 0003:31:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 7.950294] r8125 0003:31:00.0: enabling device (0000 -> 0003) [ 7.967108] r8125 0003:31:00.0 (unnamed net_device) (uninitialized): Invalid ether addr 00:00:00:00:00:00 [ 7.967112] r8125 0003:31:00.0 (unnamed net_device) (uninitialized): Random ether addr a2:83:9c:9c:cc:e8
-
I have the newest Armbian 28.08.0-trunk image running on a NanoPi R6C with a 4TB NVMe SSD. The NanoPi is only connected to power and 1G ethernet via the 1G WAN port. When using the machine as NAS with Samba and a Windows client connected there is a strange problem when receiving large files. The files are stored on the NVMe SSD with ~450MB/s read/write via PCIe 2.1x1. When transmitting files from the NanoPi to a SMB client the 1G ethernet is maxed out but when receiving files the connection drops down to ~60 MB/s every few seconds. This instantly gets fixed when using the 2.5G LAN port instead of the 1G WAN port. On that port the RX looks exactly the same as the TX. Both with 112MB/s maxed out speed. I noticed that the 1G WAN port is a combination of GMAC in RK3588s SoC and a Realtek RTL8211F Transceiver while the 2.5G LAN port is a dedicated Realtek RTL8125BG. So i suspect there is something wrong with that combination of GMAC and Realtek Transceiver on the 1G WAN port. I already tried changing the rgmii rx settings with an overlay, but that didn't have any effect. Driver problem?!
-
I did a lot of power consumption tests with my NanoPi R6C and noticed something strange when switching from kernel 5.10.110 to kernel 5.10.160. Hardware NanoPi R6C 4GB 32GB Sandisk High Endurance microSD Card Ugreen 18W USB Power Supply Software Armbian 23.5.1 Nanopi-r6s bookworm Default settings (only changing fdtfile=rockchip/rk3588s-nanopi-r6s.dtb to fdtfile=rockchip/rk3588s-nanopi-r6c.dtb in /boot/armbianEnv.txt) Switching between legacy 5.10.160 and legacy 5.10.110 kernels with armbian-config With just 1Gbit Ethernet and the power supply connected in idle (measured at wall): kernel 5.10.110: 0,92W kernel 5.10.160: 1,21W I also tested different M.2 SSD, with ASPM L1 enabled/disabled, HDMI and USB devices connected/not connected. I even tried different usb power supply. In every case the power consumption with kernel 5.10.160 is higher with no apparent benefit. You could argue that it is not a big difference but when running the system from a battery it is! What is causing this increased power consumption? I tried to run a lot of commands to find the difference between the 2 kernels but could not find a significant one. WinDiff between the 2 kernels:
-
Download: https://www.armbian.com/nanopi-r6s/ (unofficial WIP support)
