Search the Community

Hello, I tried to setup a network bridge on the Orange Pi 5 to utilize with Qemu/KVM and some virtual machines I have. Here is my armbianmonitor output: https://paste.armbian.com/dajivikohi I edited /etc/netplan/armbian-default.yaml and modified it to setup a simple network bridge. I've done this countless times on other hardware I have. I rebooted, but the bridge fails to initialize and the screen gets an error dumped out every 5-10 seconds: rk_gmac-dumac: fe1c0000.ethernet eth0: Adding VLAN in promisc mode not supported rk_gmac-dumac: fe1c0000.ethernet eth0: failed to initialize vlan filtering on this port Is bridging really not supported on this network interface? Does anyone know if there's a workaround for this? I don't even need VLANs, but it seems like the bridge itself is trying to enable vlan filtering. Thanks.

Needed/wanted to add Bluetooth to my OPi5 and also needed WiFi at the same time. Did not want to use 2 USB ports so I tried the T2UB. Working well. Bluetooth appeared on my Armbian Ubuntu Jammy setup and I plugged in the dongle. It saw a few of my bluetooth devices. Reason I wanted bluetooth is to use a controller for some games/emulators. I'll make another post for that. My PS4 Dualshock controller is not showing up in the list of devices. My version is an older version, Armbian 23.06.420 Jammy with Linux 5.10.160-rk35xx No end-user support: built from trunk Conclusion: TPLink T2UB should work properly on Armbian Ubuntu desktop.

I had one OPi5 setup and working properly with one of my TVs. I was running Kodi and using the remote from my TV to control Kodi using HDMI-CEC. I went to setup a second one on another TV but this time the TV remote did not work properly. Through elimination I came to determine the HDMI cable was the issue. I ordered another HDMI cable that had the Ferrite at each side of the cable. Now it worked properly. Thought this might be useful for others. This is the cable I ordered: https://www.amazon.ca/dp/B003PDHJ6M Conclusion: In order to make HDMI-CEC work properly, make sure the HDMI cable is of sufficient quality. I think ones with the Ferrite may be best to remove any electrical interference.

I only have options 1,4,5,7 on my nand-sata-install utility and can only boot from a single armbian microsd card but no other. /dev/mtdblock0 shows no files. Everything has been fine till now! Would love some help. Thanks

i am taping in the dark here and in need of some help. i am running openhab on armbian 23.8.1 server and i need to get audio out on 3.5 jack for alerts. openhab has only two options system speaker and web audio. web audio plays on client like browsers using pulse audio. But if i use system speaker nothing comes out. What can i do to get sound on 3.5mm out on opi? is it even possible? i have this but this is also where my knowlege ends so help needed. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: rockchipdp0 [rockchip-dp0], device 0: rockchip-dp0 spdif-hifi-0 [rockchip-dp0 spdif-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: rockchiphdmi0 [rockchip-hdmi0], device 0: rockchip-hdmi0 i2s-hifi-0 [rockchip-hdmi0 i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 2: rockchipes8388 [rockchip-es8388], device 0: dailink-multicodecs ES8323.6-0010-0 [dailink-multicodecs ES8323.6-0010-0] Subdevices: 1/1 Subdevice #0: subdevice #0 i am assuming card 2 is 3.5 out but not sure what to do with it. thanks for help!

Hey all, New to Armbian, installed to an Orange Pi 5. Installed XRDP - works fine in root (desktop shows) but if I try to do it as a user I just get a black screen with cursor. From searching I can see posts about already being logged in as a user already, and therefore black for privacy but I've not logged in as the user prior? Cant find anything really conclusive explaining how to resolve this Also even in root if I get logged out of desktop (RDP session still active, i.e. desktop lock screen) my root password doesn't work. Password is clearly not wrong

Good day, I have Opi 5 and bought this display https://www.aliexpress.com/item/1005005641383181.html?src=google&aff_fcid=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&aff_fsk=UneMJZVf&aff_platform=aaf&sk=UneMJZVf&aff_trace_key=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&terminal_id=b834b596955b44a1bf643629f5ba5647&afSmartRedirect=y . It was a blind buy ... And now I can't get it work if its even possible. I'm its my first time trying to get display on these boards usually use them trought Monitor or TV and it works flawlessly. Cant find even config.txt . But now im lost at how to get it work .. I am new to this so I would appreciate any tips or help . Have a good day

I want to install jellyfin as a docker container on my Orange pi 5. How can I enable hardware acceleration for it? On the container page (https://hub.docker.com/r/linuxserver/jellyfin) there are instructions for various options, but orange pi 5 is not there of course. I have enabled 3D acceleration as mentioned on the armbian page for orange pi 5.

and, BTW, this will probably work on any SBC that has pwm and working port of wiringPi (wiringOP is much simpler than the dtbo method, IMO) WHY: I don't like fans that run full speed ALL the time pwm fans are a bit limited on the ground in small size, and expensive The SBC has pwm pins, so why not use them none of the examples I have found are adequate, either gpio off/full or excessive python scripts, 40 lines or more,, the bash script is ~ 10 lines Some of the wiringOP/gpio packages don't work (ubuntu-full desktop) try the commands in rc.local, if they don't work, then,,, dpkg -l |grep wiring; apt remove ..... git clone https://github.com/orangepi-xunlong/wiringOP.git,, also install lm-sensors (you may have to make link, this puts gpio in /usr/local/bin, this is branch next) in rc.local: gpio mode 0 pwm #using wPi pin #'s, from gpio readall sleep 500e-3 #pause needed gpio pwm 0 900 #starts for sure gpio pwm 0 380 #slow to MIN until cron adjusts ----- gpio pwm <pin> NNN ,,,, NNN is what I will call PWR, to get range give a PWR too large, the error will give range If the PWR is too low the the fan won't start, even 800 is only 90% start The fan turns all the time, but not at full speed, at MIN you can almost count the turns (maybe 150 rpm) You have to find the PWR number for MIN for your fan, start at 300, it should run for hours, if not add 20, retest When you get some #, then add 10%. With this number, fan should run forever the script that cron calls every minute or 2 #!/usr/bin/bash TEMP=`sensors|grep bigcore0 -A3 |grep temp1 |tr -s ' '| cut -d ' ' -f 2|cut -c 2-3` #adjust grep as suitable, fails >99 echo $TEMP #TEMP=$1 #for testing, will error if $1 is blank PWR=$(("$TEMP" * 11)) #or any other number you choose echo $PWR if [ "$PWR" -gt 999 ]; then #check to see if PWR is in 'correct' range PWR=999 elif [ "$PWR" -lt 380 ] ; then #if this number is suitable for YOUR fan PWR=380 fi gpio pwm 0 $PWR ----- obviously comment out echo lines when debugging finished And now the wiring, it is stupid simple (arrows are both connections AND current flow) (-ve) <-- E pwm --> R --> B (+ve) --> Fan --> C if R is 1k, not enough drive to turn on transistor, 330 is 'iffy', 220 is OK, I have 180, depends on transistor Oh, BTW, scope told me pulses are +, so transistor is NPN, if you couldn't follow circuit logic (TO92 OK, unless fan huge) ---- and now pwmTone,,, absolutely nothing on web gpio pwmTone <pin> <frequency> ,, sounds good, right. well range likely changes, neutral as long as you know plus: fan starts MUCH better, even 1/2 PWR minus: fan barely slows down even with very low PWR If anyone knows more, please reply..... maybe there should be 5-10k pwm --> (-ve) to ensure pwm turn-off??? ---- I guess if you don't have a scope you could feed a LED + R, see if it dims (? R=100?) as you change PWR PS I would suggest this be pinned, if it is considered suitable --------- And a better debugged script, better than off the top (of my head) paying more attention to the hw side and not forgetting anything ----- #!/usr/bin/bash TEMP=`sensors|grep bigcore0 -A3 |grep temp1 |tr -s ' '| cut -d ' ' -f 2|cut -c 2-3` #adjust grep as suitable, fails >9 echo $TEMP if [ $# -gt 0 ]; then TEMP=$1 #for testing fi PWR=$(($TEMP * 11)) #or any other number you choose if [ "$TEMP" -lt 50 ]; then PWR=$(($TEMP * 8)) elif [ "$TEMP" -lt 60 ]; then PWR=$(($TEMP * 9)) elif [ "$TEMP" -lt 70 ]; then PWR=$(($TEMP * 10)) fi echo $PWR if [ "$PWR" -gt 999 ]; then #check to see if PWR is in 'correct' range PWR=999 elif [ "$PWR" -lt 380 ]; then #if this number is suitable for YOUR fan PWR=380 fi echo $PWR gpio pwm 0 $PWR

Hello, sorry if this has been answered somewhere else. I was just wondering how i upgrade my Orange Pi 5 running Arbmian 23.11.1 Bookworm w/ Linux 5.10.160-legacy-rk35xx to the latest Kernel. I tried using `sudo armbian-config` and updating via that with kernel upgrades unfrozen but it doesn't seem to work. Is there something I'm missing? Startup splash below: ___ ____ _ ____ / _ \| _ \(_) | ___| | | | | |_) | | |___ \ | |_| | __/| | ___) | \___/|_| |_| |____/ Welcome to Armbian 23.11.1 Bookworm with Linux 5.10.160-legacy-rk35xx System load: 4% Up time: 0 min Memory usage: 8% of 3.83G IP: 192.168.1.69 10.121.215.1 CPU temp: 40°C Usage of /: 6% of 57G RX today: 38.2 MiB

This https://github.com/Joshua-Riek/ubuntu-rockchip/wiki/Orange-Pi-5 produces nearly 0 dropped frames at 4K 60fps on https://www.youtube.com/watch?v=LXb3EKWsInQ While latest Armbian_23.11.1_Orangepi5_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz and doing immediately after install, only these commands: sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia sudo apt update sudo apt dist-upgrade sudo apt install mali-g610-firmware rockchip-multimedia-config exactly like it says on https://www.armbian.com/orangepi-5/ and sudo reboot produces alot of dropped frames on same youtube 4K 60fps video! What am I missing? Shouldnt there be equal accelerated video performance?

This image works OK, and we now have both a 6.7 kernel AND graphics. Minor issues: EzCast stupid windows Wifi adapter does not plug and play. The vertical USB port does not sense plugging in a device (Wifi) Good work, Gullik

Have an incident where I tried installing a newer kernel in an nvme working setup and the device wont post. My original installation flash card is working but is giving me problems. So I got 2 others and attempted to boot new version of the image and Im getting no post. I was able to solve my original problem by installing a legacy version in flash and copying /boot over to nvme. I also attempted rebuilding the mme partitions with no success. But it seems that there is something not working right with kernel 6.7.

pi@opi5:~/AoC-2023-cplusplus$ lscpu --all --extended CPU SOCKET CORE L1d:L1i:L2:L3 ONLINE MAXMHZ MINMHZ MHZ 0 0 0 0:0:0:0 yes 1800.0000 408.0000 1800.0000 1 0 1 1:1:1:0 yes 1800.0000 408.0000 1800.0000 2 0 2 2:2:2:0 yes 1800.0000 408.0000 1800.0000 3 0 3 3:3:3:0 yes 1800.0000 408.0000 1800.0000 4 0 0 4:4:4:0 yes 2256.0000 408.0000 2256.0000 5 0 1 5:5:5:0 yes 2256.0000 408.0000 2256.0000 6 1 2 6:6:6:0 yes 2304.0000 408.0000 2304.0000 7 1 3 7:7:7:0 yes 2304.0000 408.0000 2304.0000 Why the odd cortex a76 MAXMHZ values. pi@opi5:~/AoC-2023-cplusplus$ uname -a Linux opi5 5.10.160-legacy-rk35xx #1 SMP Tue Nov 28 02:45:16 UTC 2023 aarch64 GNU/Linux

FYI. Searching some forums around the web, stumbled on a post that indicated the TU3 Nano would work on the OPi 5. I thought I would give it a try. It worked for me plugged it in reboot. Download speed topped out at 200mb on the usb3 (top plug) connected to 5Ghz wifi. Happy days. Running the Feb.27 stable version of Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110_gnome_desktop. TC

Hello people, Happily running Bookworm, because it was the mainstream download for OPI5 a few months ago, I now see that the main download for OPI is back to Jammy. Apart from hardware accceleration, Bookworm runs great for me. In fact HA is not crucial for my server usage, though it would be nice. Question: what is the reason the main OPI5 download is now back to Jammy in stead of Bookworm? And what would be the advantages of going back from Bookworm to Jammy? (Got the aluminium passively cooling case for the OPI5, so far it's been great, 10 minutes of stresstesting all 8 cores doesn't get above 70 degrees celsius. For reference my Meko 3588 box without any cooling reaches over 80 degrees. On that Mekobox I am running Portainer, Docker, HomeAssistant, MosquitoServer, very stable for months and months) Bas Hamstra

I am using Wifi/BT USB dongle to connect network for Orange Pi 5. But it does not work with Armbian. It works smoothly with Orange Pi's Ubuntu and Debian distros. I just need to insert the dongle into USB 3 to work. Is there anything I can do to use the dongle with Armbian? My dongle is "USB WiFi Bluetooth Adapter Dual Band 2.4/5.8Ghz Wireless RTL8821CU Don-ig"; https://www.ebay.com.au/itm/404244701011

Anyone tried installing Steam Link? There seems to be an image in Raspberry OS but I cannot find a deb image for aarch64. Official flatpack is x64 only...

Version 20230325-edge with kernel 6.2 (pancsf-midstream). With HDMI USB LAN support. https://disk.yandex.ru/d/Xt36QdVcxRdEDA

Hi, The release notes for Armbian 23.11 state, under Key Improvements in This Release, "Mainline Kernel for RK3588 with experimental HDMI support." I am currently running the default 5.10.160-legacy-rk35xx kernel If I wanted to switch to and try out the mainline kernel for RK3588 with experimental HDMI support, would I do something like this: sudo apt install linux-image-collabora-rockchip-rk3588 After testing, If I want to rollback to the default legacy kernel, what are the steps involved? Apologies if there are instructions elsewhere that cover this. Thanks in advance for any guidance.

hello , im a 0 in linux , i have orange 5 with mvme , i folowed how to for boot directly to mvme , the how to made me delete the spi flash. all was good, o5 boot on mvme succesfully but at each reboot , my hardware have new mac adress. any one can show me what to do step by step ? i used : Joshua-Riek/ubuntu-orange-pi5: Ubuntu 22.04 LTS for the Orange Pi5 ( desktop & serveur ) Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110.img.xz ubuntu serveur 23.04 ( 64 ) it's the same on all , boot one time i have mac adress , reboot = new mac adress i cant fix ip localy , so i think when i deleted spi flash , may be deleted config to get fixed mac adress ? any help / link ? , thank's

Good evening, I have got Orange pi 5 board. MAC address of this board network interface `end1` changes every time I reboot the system. I tried adding entry in /boot/armbianEnv.txt, I tried specifying hwaddress in /etc/network/interfaces. Neither of those two options worked.

On Armbian Orange Pi 5b webpage, one can download the latest image with kernel 6.7 Rrc1, not stable. Once the kernel (6.7) is stable, will there be a way to upgrade without reinstalling? Thanks.

My Orange Pi 5 appears to be completely dead. No lights turn on when the power is connected and the SD card is freshly imaged as well. This started happening when I connected a USB-C multi-port dongle with a connected PD power supply to it. Is it possible to revive this?

Hello folks, I happily run Armbian Jammy XFCE on my much beloved Meko box (with at least SOME hardware accel) and Bookworm on Orange Pi 5. Both run excellent, but Jammy/xfce is a bit more snappy. probably because of partly harware accell. On the Meko R3588 4Gb box I installed Docker, Portainer, MQTT server container, Home Assistant container. All is well. I operate my boxes via RealVNC, so that it also will work seemlessly when VPN is active. The containers are so extremely light that they hardly take a few percent CPU. Home Assistant container takes 0,5Gig or so, MQTT server takes 0.1Gig. My first encounter with docker is very positive! Next I will try to add open VPN and SABNZB containers if possible. So...these containers got me thinking...can we run QEMU on Armbian? Probably not, but I have to ask: would it be possible to: have QEMU working on RK3588 Armbian Run for example a windows VM in QEMU? Even if it would be slow? Just playing and experimenting...never used XFCE before, it grows on me, very snappy and no-nonsense...! And with dark themes these UI's look a lot cooler in the first place IMO. PS: I don't get that my plastic Meko box doesn't get hot, without ANY active cooling. I did a stresstest for 4 minutes, all 8 cores maxed, and sensor temps reach eventually over 80 degrees. Where does the heat go? The box never gets really hot and when the stresstest ends sensor temps go straight back to 60/50s almost instantly. I quite LIKE it's completely silent and without moving parts. It's got an EXCELLENT built-in wifi adapter too! So good that I don't even bother to plug the ethernet cable in, that says it all. Maybe I'll start loving my 8Gig Opi5 more when I get a passively cooled aluminium case for it. But currently it has moving parts and NO built-in wifi and an ugly transparent case 😉 Bas