Search the Community

Hello everyone, I've got an orange pi pite 2, I install in my sd card armbian, it start but when I login and create a new account and reboot, I see termianl and not the desktop of armbian, If i reboot it ask me again to login, but I can'f see the terminal.... PLEASE HELP....... THANKS

The problem I have an USB endoscope camera that works fine with my Orange Pi lite's normal USB port. However I need both USB port for other devices, so I want to connect this same USB camera, which was orginally marketed as USB otg camera for android phones, using Opi lite's micro usb otg connector. What have I tried - In armbian-config menu, I have enabled usbhost0. I believe this overlay is for the usb otg port, but just to be sure I also enabled usbhost1, usbhost2 and usbhost3. - Using dtc I decompiled sun8i-h3-orangepi-lite.dtb into sun8i-h3-orangepi-lite.dtc. - In this dtc file, I looked up musb, and changed status = "disabled" to "okay", and added dr_mode = "host", like this usb@01c19000 { compatible = "allwinner,sun8i-h3-musb"; reg = <0x1c19000 0x400>; clocks = <0x6 0x20>; resets = <0x6 0x11>; interrupts = <0x0 0x47 0x4>; interrupt-names = "mc"; phys = <0x18 0x0>; phy-names = "usb"; extcon = <0x18 0x0>; status = "okay"; linux,phandle = <0x47>; phandle = <0x47>; dr_mode = "host" }; - Again with dtc, I compiled the dts to dtb file which replaced the old one (I've made backup). - After reboot, this seemed to have done something root@orangepilite:~$ dmesg |grep musb [ 4.086014] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 4.086025] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 9 [ 4.086290] usb usb9: Manufacturer: Linux 4.14.78-sunxi musb-hcd [ 4.086295] usb usb9: SerialNumber: musb-hdrc.1.auto However, when I connect the camera to the usb otg port, it doesn't work. The LED's on the camera doesn't turn on (so there is probably no power coming from the port, also there are no video devices on /dev/. How do I connect my camera to the micro usb port on Orange pi lite?

Hi i have a problem trying to load the drivers of this camera, could you help me? Issue: mobprobe: FATAL: Module ov5647 not found in directory /lib/modules/4.14.84-sunix Board: Orange Pi Lite Camera sensor: OV5647 fisheye OS: Ubuntu - Armbian 5.65

I would like to add the Orange Pi Lite 2 into the discussion of boards to support. Info from Orange Pi site - http://www.orangepi.org/Orange Pi Lite 2/ Hardware specification CPU H6 Quad-core 64-bit ARM Cortex™-A53 GPU • High-performance multi-core GPU Mali T720 • OpenGL ES3.1/3.0/2.0/1.1 • Microsoft DirectX 11 FL9_3 • ASTC(Adaptive Scalable Texture Compression) • Floating point operation greater than 70 GFLOPS Memory (SDRAM) 1GB LPDDR3 (shared with GPU) Onboard Storage TF card (Max. 32GB) /MMC card slot WIFI+BT AP6255, IEEE 802.11 AC/bb/g/n, BT4.1 Audio Input MIC Audio Output HDMI 2.0a Video Input A CSI input connector Camera: Support 8 bit digital camera interface Maximum still capture resolution for parallel interface to 5M Maximum still capture resolution for parallel interface to 5M Video Decoding H265/HEVC Main/Main10 profile@Level5.2 High-tier ;4K@60fps, up to 6Kx4K@30fps H264/AVC BP/MP/HP@level5.1, MVC, 4K@30fps VP9，Profile 0/2, 4K@30fps AVS+/AVS JIZHUN profile@level 6.0, 1080P@60fps Video Outputs HDMI 2.0a TX with HDCP 2.2 output Power Source DC input, USB OTG input can supply power PMU AXP805 USB 2.0 Ports One USB 2.0 Host, one Micro USB 2.0 USB 3.0 Ports One USB 3.0 Host Low-level peripherals 26 Pins Header GPIO(1x3) pin UART, ground. LED Power led & Status led IR Receiver Yes Key Power(K1) Supported OS Android, Ubuntu, Debian Interface definition Product size 69 mm × 48mm Weight 50g Orange Pi™ is a trademark of the Shenzhen Xunlong Software CO., Limited

Is there any other firmware for the AP6255 available, besides the one made available for Khadas VIM at https://github.com/khadas/android_hardware_amlogic_wifi/tree/Vim/bcm_ampak/config/6255/BT or the one for the Raspberry Pi 3+ available e.g. at https://github.com/OpenELEC/misc-firmware/blob/master/firmware/brcm/BCM43430A1.hcd which uses also the same chipset? I am trying to make Bluetooth working on an Orange Pi Lite2. So far I had no success loading the firmware by issuing root@orangepilite2:~# brcm_patchram_plus --patchram /lib/firmware/brcm/BCM43430A1.hcd --enable_hci --bd_addr 11:22:33:44:55:66 --no2bytes --tosleep 1000 /dev/ttyS1 root@orangepilite2:~# brcm_patchram_plus --patchram /lib/firmware/brcm/BCM4345C0.hcd --enable_hci --bd_addr 11:22:33:44:55:66 --no2bytes --tosleep 1000 /dev/ttyS1 Any suggestions?

My docker build dev 5.0.y is not booting from sd card. U-Boot SPL 2019.01-armbian (Mar 16 2019 - 05:27:40 +0000) DRAM:This DRAM setup is currently not supported. resetting ...

Hey all, I understand these things are in active development at the moment. I was attempting to use the usb 3.0 socket on the lite 2 with stretch, except it did not respond at all - looking at dmesg shows the following error: [ 1.806055] sun4i-usb-phy 5100400.phy: Couldn't get regulator usb0_vbus... Deferring probe [ 1.806320] sun50i-usb3-phy 5210000.phy: failed to get phy clock which from my limited experience with linux kernel seems to indicate that the device tree config may be incorrect for the board - as most searching for these errors show the code added as part of updates to get the pine64 board's usb 3.0 stack working. USB 2.0 socket is working on the board. if need be i can test nightly's (i don't have a linux environment to hand to compile a kernel myself, and i do have a serial device i can connect to get raw output - just need to look up pinouts to ensure i connect it correctly). link to full dmesg if it is useful: https://pastebin.com/4vJDxk9N

When trying to upgrade, I get the following error: root@orangepilite2:~# apt upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: armbian-firmware 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/5,755 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue? [Y/n] (Reading database ... 38292 files and directories currently installed.) Preparing to unpack .../armbian-firmware_5.74.190202_all.deb ... Unpacking armbian-firmware (5.74.190202) over (5.72.190122) ... dpkg: error processing archive /var/cache/apt/archives/armbian-firmware_5.74.190202_all.deb (--unpack): trying to overwrite '/lib/firmware/regulatory.db', which is also in package wireless-regdb 2018.05.09-0ubuntu1~18.04.1 dpkg-deb: error: paste subprocess was killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/armbian-firmware_5.74.190202_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) root@orangepilite2:~# So it seems there is a duplicate regulatory.db - in the firmware as well as in wireless-regdb

I have bought 3 OPi Lite 2 (H6 based) dev boards. Just downloaded the latest Bionic image at the following link: https://www.armbian.com/orange-pi-lite-2/ I understand it's WIP. However, it seems to have issue on booting up. I connected HDMI cable and upon boot up, I could see init info on the screen, then it says, starting Kernel ... , then screen goes no signal, power LED stays RED forever. I read that the current image seems to have issue on HDMI. But it worked with HDMI upon initial bootup, then stopped working. My problem is that without HDMI, how could I edit the WIFI config to have the board connected to my network thus to SSH into the board for further dev? Can anyone provide a link to an known working image or guide me how to configure WIFI without HDMI output? Thanks!

RT, i am trying to use git and aarch64 tools to compile a lastest u-boot by my own,but ,it failed. there're the steps i was doing: 1. downloads the latest u-boot source code from offical web: git clone git://git.denx.de/u-boot.git 2.downloads the ARM Trusted Firmware from offcial web: git clone https://github.com/ARM-software/arm-trusted-firmware 3.compile the ATF for BL31 by using this cmd: sudo make CROSS_COMPILE=aarch64-linux-gnu- PLAT=sun50i_h6 all and then move the BL31 file into the u-boot root fold. 4. compile the u-boot for H6 by using this cmd: sudo make ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- orangepi_lite2_defconfig sudo make 5.burn the u-boot-sunxi-with-spl.bin file on SD card following the README.sunxi64 file dd if=u-boot-sunxi-with-spl.bin of=/dev/sdx bs=8k seek=1 6.plug in the sd card and connect the uart port and power on,i think and i am sure the default baudrate is 115200, but when i open the terminal and try to read and debug the u-boot,it displayed as blow: " 膂秜?第曤W -#1?!?!!?!%縠ey濆?y,XWm颟Y纣?搔f鞗df氭停搾MO5Z&?挺?矻歀2撡33N檍曋?攻K/]媬~{紊觙斐─蓲懗逃痔L嫣1ff瞟黍骃娉姒鍸?,XW阱℡骟?搔f袒﹔'Q摀?:ど$$M~迿麚%?驧&?LM?,XW阱?篌?e觙? 猟蓳SU?蓱s筫r潴?騠檽揙鏆SI覔搾1摔2IS撜蓅K蒕?y?W隍?篌螗K+Y篌ed疑扡觵邋歃櫈=y統経i疕H眼鲋謑碇Vm旉V龆諺-赩谥谥獀?鷞徽竖膂鲔鲋鲮+V冬鰈熘霮?鲻鲋黼?娫U蕑 : 妀T脲難_U嬁靠}''-##5縪摽痀Uc暉m隤+镾右?m?姫?岛V雡[}e嬁繚縬-{咫YY^丙U5氇胨u?曞-V雊!=7-#1縰#-!#%5#?!%縮}W＃？U踊蔜?*竖?mm?[けT谠?鶸鲻鲻Vo/V蜒丙T谠?鶸鲻鲻Vo创禧T谠?鶸鲻鲻Vo央j鬕猨艋t轸氇ti 篢鳆埚镲镫?镲稃??FDKQч?在t蚤?iR羲鹶??%9熆-?5#?5-95咫档k?氷:j胡趖詑?i译鯷[+?=-#1縐Y{＃ｅ隿!?!#!''5?!#7咫UY{??!57？_'5=5?5勘;?=笨3-ｅ?=-#1縐Y{＃ｅ隿!?!#!''5?!#7咫c!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁5-7咫%--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31煙煙煙熷隿!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31煙煙煙咫c!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31煙煙熷隿!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31煙煙咫c!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31煙熷隿!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31煙咫c!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31熷隿!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31咫c!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31?53='?%?#-咫c!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31?53='?%咫c!?/5#5?!#7ｅ?--#1?#-!#%5#?=-=;'5嬁;!!3-'5咫[5-5-#1?-'5嬁5'-#?31?53='咫c!?/5#5?!#7ｅ難!#3-1?-'5?!?!#7咫=-#1縐Y{＃ｅ隿!?!#!''5?!#7咫c!?/5#5?!#7ｅ?" (sorry for unable to paste the sreenshot.....) i can't read anything... can you help me? thx so much!!!

Latest doesn't seem to work at all, so something like 5.59 4.18.0-rc7-sunxi64 mentioned here https://github.com/armbian/testings would be ideal. Alternatively is there a way I can build old version myself? I ran ./compile docker BOARD=orangepilite2 BRANCH=dev but resulting image doesn't work also.

hello , I have Opi lite 2 I want to use it as low load server with minimal power consumption (min temp) I edited /etc/default/cpufrequtils like that min_speed=120000 max_speed=480000 governor=ondemand but it works on 888mhz constantly with load and without load (image 2) Ps: I have also OPi PC+ and edit of cpufrequtils works ok on it (image 1) what am I do wrong, or maybe armbian-config monitor doesn't work properly ? ARMBIAN 5.67.181202 nightly Ubuntu 18.04.1 LTS 4.19.4-sunxi64

# uname -a Linux H6 4.18.13-sunxi64 #3 SMP Fri Oct 12 17:43:44 CST 2018 aarch64 GNU/Linux 1, burn the image to SD card 2, use nand-sata-install command, burn emmc 3, remove the SD card 4, reboot the board, can't boot, the error message: U-Boot SPL 2018.09-rc1-armbian (Oct 12 2018 - 17:39:13 +0800) DRAM: 1024 MiB Trying to boot from MMC2 MMC Device 1 not found spl: could not find mmc device. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### root@H6:/mnt/emmc# fdisk -l Disk /dev/mmcblk0: 30 GiB, 32218546176 bytes, 62926848 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x36326db0 Device Boot Start End Sectors Size Id Type /dev/mmcblk0p1 8192 62297567 62289376 29.7G 83 Linux Disk /dev/mmcblk2: 7.3 GiB, 7818182656 bytes, 15269888 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x7b2f8591 Device Boot Start End Sectors Size Id Type /dev/mmcblk2p1 8192 15117183 15108992 7.2G 83 Linux mkdir /mnt/emmc mount /dev/mmcblk2p1 /mnt/emmc and then I try modify the /mnt/emmc/boot/boot.cmd and /mnt/emmc/boot/boot.scr files, setenv rootdev "/dev/mmcblk0p1" change mmcblk0p1 to mmcblk2p1 if test "${devtype}" = "mmc"; then part uuid mmc 0:1 partuuid; fi change "mmc 0:1" to "mmc 2:1" and I check the emmc device UUID, is correct. root@H6:/mnt/emmc/boot# cat armbianEnv.txt verbosity=1 console=both overlay_prefix=sun50iw6p1- rootdev=UUID=178e84b7-40bc-4ebc-922d-9850051c8c00 rootfstype=ext4 user_overlays=network usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u root@H6:/mnt/emmc/boot# blkid /dev/mmcblk0p1: UUID="9766d929-82b6-4c2f-90e0-6f422af64df5" TYPE="ext4" PARTUUID="36326db0-01" /dev/mmcblk2p1: UUID="178e84b7-40bc-4ebc-922d-9850051c8c00" TYPE="ext4" PARTUUID="7b2f8591-01" /dev/zram0: LABEL="log2ram" UUID="00102ace-f4c5-4d78-af23-3a8b22b9f360" TYPE="ext4" /dev/zram1: UUID="a4a7b532-e8d5-481b-a5ed-5616bf0ad9fa" TYPE="swap" /dev/zram2: UUID="62a328b0-3e44-41ff-a9dd-79a49d74d9c7" TYPE="swap" /dev/zram3: UUID="3b5ed341-f05b-4907-b965-8840f2541c82" TYPE="swap" /dev/zram4: UUID="14517095-4a69-4210-bbd8-d53c1a34d3d7" TYPE="swap" /dev/mmcblk0: PTUUID="36326db0" PTTYPE="dos" /dev/mmcblk2: PTUUID="7b2f8591" PTTYPE="dos" follow this document, can't find script.bin in system. https://forum.armbian.com/topic/1702-orange-pi-plus-2e-where-is-16ghz-and-sd/?tab=comments#comment-13163 where is the problem, any help ? thinks.

hdparm -t gives only 2-3MB/s for the internal mmc card. Any ideas? The card does over 80MB/s on my workstation.

The current image for OrangePiLite2 Armbian Bionic/Stretch not booting I tried, Armbian_5.64.181019_Orangepilite2_Ubuntu_bionic_dev_4.18.15 and Armbian_5.64.181023_Orangepilite2_Debian_stretch_dev_4.18.16. When connected to HDMI monitor, I just a red light up and nothing else. However, this version of image works, Armbian_5.59.180824_Orangepilite2_Debian_stretch_dev_4.18.0-rc7

Recently I tested armbian stretch for orange pi lite2. If there is not other task except system, there work fine. But if there are some high cpu tasks, such as unzip, the system load will go high, and not go to lower level when task done. When the system load is higher than 4, the response of the system is laggy, when go higher, the system will go no response. I use uptime to test the system load, when boot, the 1min load will be at 3.xx and go down slowly. When no task, the load will lower than 0.5.

Can someone recommend a good & cheap heatsink for the Lite2 from Aliexpress?

Hi, I recently read from github testings of orange pi lite2 testing that wireless is working. But I download from the official website of https://dl.armbian.com/orangepilite2/Debian_stretch_dev_nightly.7z(built 0824) and burn it, it starts, but the wireless is missing. I also read that the firmware added ap6255 wireless driver, so I download https://beta.armbian.com/pool/main/a/armbian-firmware-full/armbian-firmware-full_5.59.180915_all.deb and installed it. After reboot, the wireless is still missing. So the support of wireless is built-in or usb? Should I build armbian myself with the lastest code to support the built-in wireless? Thank you.

how can I force set HDMI output like 1024x768 60hz or something like that? hello I have OPI lite 2, I use Armbian_5.61.180927_Orangepilite2_Ubuntu_bionic_dev_4.18.10.img, when I boot OPI I can see preboot information then after 1-3 sec I have no signal on my monitor I tried different hdmi cables without luck uname -a Linux orangepilite2 4.18.11-sunxi64 #312 SMP Sun Sep 30 00:22:52 CEST 2018 aarch ps: monitor dell 2414h I tried different OS like android (native, zidoo h6 pro, beelink gs1) also ubuntu 16.04 without any monitor issue, at least video output worked at any cases but they have another issues

vmware 12, Ubuntu 16.04: ./compile.sh, then select WIP version, orangepi lite2, the dialog exited, and message under in terminal: Error: Expected at least 5 tokens for --menu, have 4. Use --help to list options. [ error ] ERROR in function source [ main.sh:188 ] [ error ] No kernel branch selected

LANG=en_CN.UTF-8 I have it+SD card+usb TouchScreen+HDMI Screen which work with http://www.orangepi.org/'s image. I've downloaded https://dl.armbian.com/orangepilite2/Debian_stretch_next.7z,verified the sha256 checksum,burn SD card,verified checksum of SD card... After UBoot, nothing was displayed,but `fdisk -l /dev/sdb` changed -------------------------------- Disk /dev/sdb: 30 GiB, 32220643328 bytes, 62930944 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x16977123 Device Boot Start End Sectors Size Id Type /dev/sdb1 8192 62301631 62293440 29.7G 83 Linux ------------------------------- How to make it work?

Hi, I have flashed Armbian_5.35_Orangepilite_Ubuntu_xenial_default_3.4.113_desktop.img - and it works fine with my Orange Pi Lite v.1.1 But if I flash Armbian_5.38_Orangepilite_Debian_stretch_next_4.14.14.img which is aslo supported, the device does not boot. At least I get no output on HDMI, and no serial console over OTG. So I cannot check if it does not boot at all, or dies somewhere in the middle How can I check why it does not boot?

I am building armbian with mainline kernel (4.14.19) on jessie for OrangePi Lite... Sometimes on booting my Pi Lite, the wifi does not work. I cannot create hotspot and connecting to existing networks will not work. A short time after booting I see the following messages in the dmesg log [ 102.077151] sunxi-mmc 1c10000.mmc: send stop command failed [ 102.077184] sunxi-mmc 1c10000.mmc: data error, sending stop command If I remove and reload the 8189fs module I will see the following error in the dmesg log [ 572.371452] rtl8189fs: probe of mmc1:0001:1 failed with error -110 If I don't see the mmc errors after startup (say 5 minutes) the wifi works fine. I can also remove and reload the kernel module as I please and create a hotspot or connect to an existing network. Has anyone else seen this problem or have any workarounds?

Hi, I thought instead of waiting for mainline kernel support for these boards, if it would be possible to use Allwinner H6 BSP 4.9.56 kernel? Found at https://github.com/Allwinner-Homlet/H6-BSP4.9-linux I am able to compile it on Sunxi's Ubuntu 16.04 Beta image, however from the serial output it seems to at least have trouble with the sd card initializing. I tried to copy over the sd card information in sdmmc@04020000 from Sunix's own /boot/orangepi/OrangePiH6.dtb into Allwinners sun50iw6p1.dtsi but the boot only went a little further ending in a similar kernel panic to when I used the the BSP4.9 with Sunxi's original OrangePiH6.dtb. I am not very skilled at this and do not think I can finish it off, if it's possible at all. I copy the dtb to the same folder with the same filename in my testing. Apparently most of the drivers work, including the cpufreq which is what is notably missing in the current Armbian WPI images. The old BSP 3.10.65 kernel is next to impossible to use any usb wifi dongles for the One Plus. I have attached the output of my experiments. Cheers, Rauli BSP3.10.65-Sunxi-dmesg-normal-boot.txt BSP4.9-AllwinnerH6.txt BSP4.9-AllwinnerH6-using-stock-BSP3.10.65-dtb-kernel-panic.txt

No nameserver in these files too /etc/resolvconf/run/resolv.conf /run/resolvconf/resolv.conf The nameserver is set in this file only /run/NetworkManager/resolv.conf This is the content of /etc/NetworkManager/NetworkManager.conf [main] dns=none plugins=ifupdown,keyfile [ifupdown] managed=true [keyfile] unmanaged-devices=interface-name:p2p0 These are relevant lines from systemd journal: Oct 29 21:47:24 orangepilite NetworkManager[507]: <info> [1509306444.9814] dhcp-init: Using DHCP client 'dhclient' Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.2421] dhcp4 (wlan0): activation: beginning transaction (timeout in 45 seconds) Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.2570] dhcp4 (wlan0): dhclient started with pid 771 Oct 29 21:47:29 orangepilite dhclient[771]: DHCPREQUEST of 192.168.143.42 on wlan0 to 255.255.255.255 port 67 Oct 29 21:47:29 orangepilite dhclient[771]: DHCPACK of 192.168.143.42 from 192.168.143.10 Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4358] dhcp4 (wlan0): address 192.168.143.42 Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4360] dhcp4 (wlan0): plen 24 (255.255.255.0) Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4361] dhcp4 (wlan0): gateway 192.168.143.10 Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4361] dhcp4 (wlan0): server identifier 192.168.143.10 Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4362] dhcp4 (wlan0): lease time 14400 Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4363] dhcp4 (wlan0): hostname 'orangepilite' Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4364] dhcp4 (wlan0): nameserver '192.168.143.10' Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4365] dhcp4 (wlan0): domain name 'lan' Oct 29 21:47:29 orangepilite NetworkManager[507]: <info> [1509306449.4366] dhcp4 (wlan0): state changed unknown -> bound IP address, netmask and default gateway are set as expected. Regards