Search the Community

after installing wireguard (kernel upgrade + headers) the pi would no longer boot and fail with crc error. Looking at the boot partition the uinitrd file was linked to the old version. Changed the uinitrd link to the newest one and it booted again.

Hi everyone, Very green here. Basically I setup 1 of my orange pi a few months back with "Armbian_23.02.3_Orangepizero2_jammy_legacy_4.9.318". I recently bought another pi and wanted to set it up with a newer version. I see bookworm is now the latest. I have tried both CLI and Minimal but whenever I flash those into my micro SD the orange pi never boots up. My router doesnt see the connection, so it cant hand off an IP. I thought maybe it was a bad mini SD or a bad pi. But when I flashed the old jammy image into the same SD, the pi immediately picked up the connection, my router gave it an IP and I was able to log in as a root to the pi. I read the documentation, and even saw the beginner videos to see that I wasnt doing something wrong. I had the SD connected before I powered on the PI, ensured I was the usb c for power. And that the SD has enough memory (8gb). Does anyone have an idea of what could be happening here with the bookworm armbian?

Hi, I use an OrangePi Zero as a race timer for a car. It is powered from the car. So when the car starts the OrangePi gets power and boots and when the car is turned off the OrangePi loses power and "turns off". This isn't ideal but I don't have a lot of options. I feel like this is a fairly common use case for electronics in cars especially ones like race timers etc. Unless I have a battery as well. I was wondering what are the best things to do to protect against the sudden power loss so that I don't corrupt anything? Is it possible to make parts of the file system read only maybe? All I do with the OrangePi is run a C++ application, it uses two serial ports and runs a server on port 80. The application does read and write its own configuration files and log files. But these are not OS files, only files that the application created itself. I have noticed that after writing or appending to a file from C++, if the power is pulled and then plugged back in the change to the file does not persist. I can ssh on before the power is pulled and `cat` the file and see that it is updated. Seems that the file data is held in RAM for a little while before actually writing. Is there anyway to force file writes to actually be flushed and written straight away?

Hi, I have a board Orange Pi Zero with modified PAs for power of WiFi module from PA20 to PA02, by soldering a connection on board. This is done to allow connection of I2C DAC. I see that board definition in 'u-boot/configs/orangepi_zero_defconfig' It uses dts definition of: 'arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts' I need to modify one section of this dts file from: reg_vcc_wifi: reg_vcc_wifi { compatible = "regulator-fixed"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-name = "vcc-wifi"; enable-active-high; gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>; to: reg_vcc_wifi: reg_vcc_wifi { compatible = "regulator-fixed"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-name = "vcc-wifi"; enable-active-high; gpio = <&pio 0 2 GPIO_ACTIVE_HIGH>; How can I do this and use armbian build script: compile.sh Thanks, Michal

Bookworm 6.1.30 - wi-fi don't work.

Running the command below I have the issue below: I work with armbian-build git repo, tag 23.02.0-trunk.0256 and I run this command to build a armbian .img for my orangepi zero lts. It used to work well in february but now maybe the armbian repositories do not work anymore with this tag version ? ./armbian-build/compile.sh docker USE_MAINLINE_GOOGLE_MIRROR=yes BOARD=orangepizero BRANCH=current BUILD_KSRC=no RELEASE=bullseye BUILD_DESKTOP=no BUILD_MINIMAL=yes KERNEL_ONLY=no KERNEL_CONFIGURE=no ROOTFS_TYPE=ext4 BOOTFS_TYPE=fat COMPRESS_OUTPUTIMAGE=sha,img ' Processing triggers for resolvconf (1.87) ... [ o.k. ] Checking MD5 sum of installed packages [ debsums ] debsums: changed file /usr/share/doc/base-files/changelog.gz (from base-files package) debsums: changed file /etc/os-release (from base-files package) debsums: changed file /etc/issue.net (from base-files package) debsums: changed file /etc/issue (from base-files package) [ error ] ERROR in function create_rootfs_cache [ functions/cli/cli-entrypoint.sh:109 -> functions/main/build-tasks.sh:302 -> functions/main/build-tasks.sh:225 -> functions/main/rootfs-image.sh:66 -> functions/rootfs/create-cache.sh:229 -> functions/logging/traps.sh:0 ] [ error ] MD5 sums check of installed packages failed [ o.k. ] Process terminated [ error ] unmount_on_exit() called! [ functions/cli/cli-entrypoint.sh:109 -> functions/main/build-tasks.sh:302 -> functions/main/build-tasks.sh:225 -> functions/main/rootfs-image.sh:66 -> functions/rootfs/create-cache.sh:229 -> functions/logging/traps.sh:1 -> functions/main/rootfs-image.sh:0 ] [ o.k. ] Unmounting [ /root/armbian/.tmp/rootfs-329b560e-4e99-40c7-bad2-3ddabd8752c8/ ] [ error ] ERROR in function unmount_on_exit [ functions/cli/cli-entrypoint.sh:109 -> functions/main/build-tasks.sh:302 -> functions/main/build-tasks.sh:225 -> functions/main/rootfs-image.sh:66 -> functions/rootfs/create-cache.sh:229 -> functions/logging/traps.sh:1 -> functions/main/rootfs-image.sh:27 -> functions/logging/traps.sh:0 ] [ error ] debootstrap-ng was interrupted [ o.k. ] Process terminated Thank you for your help

First, I have installed latest Armbian 23.8 Bookworm CLI, boot works fine, I can login Then, I have installed wireguard. As a dependency, wireguard install linux-image-6.1.0-12-rt-armmp After reboot device is unavailable in network (orange LAN LED blinking while green does not, I assume ethternet broken with this kernel)

Now that xradio has been enabled on kernel 6.x, I'm ready to upgrade my Orange Pi Zero that I've been keeping on 23.02 with kernel 5.x. With armbian-config I've unfrozen kernel/firmware updates and after apt upgrade and reboot I am on kernel 6.1.53 and wifi is working! But boot message says I'm still on 23.02, and apt says that armbian-bsp-cli-orangepizero is being kept back. Now trying: $ sudo apt install armbian-bsp-cli-orangepizero [...] Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: armbian-bsp-cli-orangepizero-current : Depends: base-files (>= 23.8.3) but 23.8.1-bullseye is to be installed E: Unable to correct problems, you have held broken packages. Do I just need to wait for something to be updated in the repositories so that armbian-bsp-cli-orangepizero will be made available, or have I messed up something on my system that I need to fix?

Should it be possible to take a working SD card out of one OrangePi Zero and put it in a new one? Same board and amount of RAM and everything.

I'm on Armbian 22.11.1 Jammy / 22.04.1 LTS, kernel 5.15.80-sunxi. Orange Pi Zero LTS. I have the issue that using all available audio players, the first half a second or so of mp3s are cut off randomly. Meaning that sometimes the beginning plays correctly, sometimes part of the beginning is cut off. Repeadetly running the player sometimes works sometimes cuts off the audio. I have tried play, ffplay, both have this issue. The speaker is a small amlfier module, the LINEOUTL output is connected to it, but the right is the same. Any ideas where to look? This is driving me insane. Thanks! I have attached a test mp3, which is hungarian, sorry. The output is from the Google Cloud Text to Speech python package, saved as a file: with open(file_name, "wb") as out: out.write(response.audio_content) tts_output.mp3

Help me, my orangepizero wont work. Every time i try to start ssh it say connection refused. Only sometimes it works. I recently installed Armbian 22.5 bullseye and after that it stopped working. Pls help

I am trying to figure out how to compile and load the Xradio drivers onto an orange pi zero LTS. I am having some troubles with the xradio drivers that came with my image and am hoping that https://github.com/fifteenhex/xradio will add some improvements. There does seem to be some code change so I am remaining optimistic. I am able to compile the drivers with the kernel from https://github.com/orangepi-xunlong/orangepi-build but it crashes network manager and a few other modules when I try to modprobe it, I am guessing it is because this kernel is not an armbian kernel. I am trying to get the kernel https://github.com/armbian/build to work, but it doesn't look like that's what I need to do. I am lost as to how to get this compiled and any help would be appreciated.

I have orange pi zero board ..i searched a lot for changing boot splash screen ( currently "armbian universal operating system" which is enabled by adding bootlogo=true in armbianEnv.txt ) I have tried Plymouth it is not working After searching lot i knew about if we can replace bootsplash.armbian , it can help because then neither we need to change uboot packages nor we have to add quiet splash like words etc in armbianEnv.txt. https://github.com/armbian/build/tree/master/packages/blobs/splash. With help of this bootsplash-packer Can anyone list me some steps ( in short ) How to run this script and create bootsplash.armbian and replace it

My OrangePi Zero is on 23.02 and I intend to stay with it (unless/until xradio wifi works on kernel 6.x). Just ran apt update and it shows these available packages: armbian-config/bullseye,bullseye 23.08.0-trunk--1-SA9048-Baeda all [upgradable from: 23.02.2] armbian-firmware/bullseye,bullseye 23.08.0-trunk--1-SA1251-B226d all [upgradable from: 23.02.2] armbian-zsh/bullseye,bullseye 23.08.0-trunk--1-SAbfee-Baf88 all [upgradable from: 23.02.2] I'm surprised to see anything related to 23.08 seeing as that version hasn't been released yet, so obviously I don't really understand what it means to be seeing this. Should I go ahead and install these even though I don't intend to upgrade to 23.08? Maybe this should be in the "beginners" area; mods please feel free to move if appropriate.

Hello, I would like to know how they reduce the size of the images and then, when the microSD cards are inserted into a card, they expand to fill the entire space. In other words, the same thing that Armbian images do when we use them for the first time: they are small, and then they occupy all the storage space.

Hello all, I'm trying to revive my old OPIZ + cheap expansion board. I've tried all recent images available but I couldn't get it to work. Is there any old version (with repository still alive) available with which I can install sox + alsa. I don't need recent kernel or software (but wifi) Any idea? Thanks for help Pascal

ARMBIAN 5.41 user-built Debian GNU/Linux 9 (stretch) 4.14.34-sunxi, Orange Pi Zero board. Very limited Debian installed, wifi doesn't work. I found lines install xradio_wlan /bin/false install 8189es /bin/false in /etc/modprobe.d/blacklist.conf and removed it. In /etc/modules-load.d/modules.conf I added the lines 8189es xradio_wlan. No help, wi-fi didn't work, nothing about xradio or wifi in dmesg. I figured out that there was no drivers (modules) for wifi. Found this article https://linux-sunxi.org/Wifi I execute the commands from the article, section RTL8189ES / RTL8189ETV The driver has its own repository: git clone https://github.com/jwrdegoede/rtl8189ES_linux.git cd rtl8189ES_linux make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux This is what it says root@its-02-o:~# git clone https://github.com/jwrdegoede/rtl8189ES_linux.git Cloning into 'rtl8189ES_linux'... remote: Enumerating objects: 2565, done. remote: Counting objects: 100% (807/807), done. remote: Compressing objects: 100% (413/413), done. remote: Total 2565 (delta 432), reused 670 (delta 385), pack-reused 1758. Receiving objects: 100% (2565/2565), 7.29 MiB | 2.32 MiB/s, done. Resolving deltas: 100% (1476/1476), done. root@its-02-o:~# cd rtl8189ES_linux root@its-02-o:~/rtl8189ES_linux# make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux make ARCH=arm CROSS_COMPILE=arm-linux-gnu- -C ../linux M=/root/rtl8189ES_linux modules make[1]: *** ../linux: No such file or directory. Stop. Makefile:2292: recipe for target 'modules' failed make: *** [modules] Error 2 root@its-02-o:~/rtl8189ES_linux# What am I doing wrong? How do I install WiFi modules (drivers)? And the following is in the dmesg vcc-wifi: disabling What is this wifi power disabling? How do I turn it on? Googling didn't help, I couldn't find anything clear about vcc-wifi: disabling Don't suggest installing a new/other Debian. Important software works on it (everything works over LAN), you just need to enable wi-fi. Translated with www.DeepL.com/Translator (free version) ARMBIAN 5.41 user-built Debian GNU/Linux 9 (stretch) 4.14.34-sunxi, плата Orange Pi Zero. Очень какой-то урезаный Debian установлен, не работает Wi-Fi. Нашел в файле /etc/modprobe.d/blacklist.conf строки install xradio_wlan /bin/false install 8189es /bin/false, удалил. В файле /etc/modules-load.d/modules.conf добавил строки 8189es xradio_wlan. Не помогло, wi-fi не заработал, в dmesg ничего про xradio или wifi нет. Понял что нет драйверов (модулей) Wi-Fi. Нашел такую статью https://linux-sunxi.org/Wifi Выполняю комманды из статьи, раздел RTL8189ES / RTL8189ETV Driver has its own repository: git clone https://github.com/jwrdegoede/rtl8189ES_linux.git cd rtl8189ES_linux make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux Вот что пишет root@its-02-o:~# git clone https://github.com/jwrdegoede/rtl8189ES_linux.git Cloning into 'rtl8189ES_linux'... remote: Enumerating objects: 2565, done. remote: Counting objects: 100% (807/807), done. remote: Compressing objects: 100% (413/413), done. remote: Total 2565 (delta 432), reused 670 (delta 385), pack-reused 1758 Receiving objects: 100% (2565/2565), 7.29 MiB | 2.32 MiB/s, done. Resolving deltas: 100% (1476/1476), done. root@its-02-o:~# cd rtl8189ES_linux root@its-02-o:~/rtl8189ES_linux# make -j4 ARCH=arm CROSS_COMPILE=arm-linux-gnu- KSRC=../linux make ARCH=arm CROSS_COMPILE=arm-linux-gnu- -C ../linux M=/root/rtl8189ES_linux modules make[1]: *** ../linux: No such file or directory. Stop. Makefile:2292: recipe for target 'modules' failed make: *** [modules] Error 2 root@its-02-o:~/rtl8189ES_linux# Что не так делаю? Как установить модули (драйвера) WiFi? А вот такое в dmesg есть vcc-wifi: disabling Что это питание wifi отключено? Как включить? Гугление не помогло, не нашел ничего внятного про vcc-wifi: disabling Не предлагайте установить новый/другой Debian. На нем работает работает важный софт (по LAN все работает), нужно просто включить wi-fi. Если можно на русском. Английский только с переводчиком :-(

I've change OpiZero's cpu from H2+ to H5, and made linux5.4.65 image with the option of "Orangepiplus (H5)" of the Build-Package which described in the Orangepi manual. After the linux startup, the output of command DMESG shows "sunxi-mmc 1c10000.mmc: Cannot do DMA to address 0x00008000514a3870", and TRACE as follows: [ 212.402793] xradio_wlan: version magic '5.15.27-station SMP preempt mod_unload aarch64' should be '5.4.65-sunxi64 SMP mod_unload aarch64' [ 248.019893] xradio_wlan: loading out-of-tree module taints kernel. [ 248.024327] xradio_wlan: module verification failed: signature and/or required key missing - tainting kernel [ 248.027506] xradio: XR819 device discovered [ 248.030479] sunxi-mmc 1c10000.mmc: Cannot do DMA to address 0x0000800051e83870 [ 248.030507] sunxi-mmc 1c10000.mmc: overflow 0x0000800051e83870+8 of DMA mask ffffffff bus mask 0 [ 248.030538] ------------[ cut here ]------------ [ 248.030572] WARNING: CPU: 2 PID: 1513 at kernel/dma/direct.c:35 report_addr+0x38/0xa0 [ 248.030578] Modules linked in: xradio_wlan(OE+) zstd rtl8xxxu rtl8192cu rtl_usb rtl8192c_common rtlwifi mac80211 cfg80211 libarc4 snd_soc_simple_card snd_soc_simple_card_utils sun8i_codec_analog sun8i_adda_pr_regmap sun4i_i2s sun4i_gpadc_iio sun4i_tcon sun8i_tcon_top sun8i_mixer cpufreq_dt zram sch_fq_codel usb_f_acm u_serial g_serial libcomposite ip_tables x_tables autofs4 fixed gpio_regulator [ 248.030691] CPU: 2 PID: 1513 Comm: insmod Tainted: G OE 5.4.65-sunxi64 #2.2.2 [ 248.030697] Hardware name: Xunlong Orange Pi Zero Plus (2pw5, Linux-Kernel Device Tree) (DT) [ 248.030707] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 248.030720] pc : report_addr+0x38/0xa0 [ 248.030731] lr : report_addr+0x98/0xa0 [ 248.030736] sp : ffff800011e833c0 [ 248.030741] x29: ffff800011e833c0 x28: ffff800011e83dd0 [ 248.030752] x27: 0000000000000000 x26: ffff800011e836e8 [ 248.030763] x25: ffff800011e83600 x24: 0000000000000000 [ 248.030773] x23: 0000000000000002 x22: ffff000036706810 [ 248.030782] x21: 0000000000000008 x20: ffff000035ccf000 [ 248.030793] x19: ffff000036706810 x18: 0000000000000020 [ 248.030802] x17: 00000000000012b0 x16: 00000000000012a0 [ 248.030812] x15: ffff800011085000 x14: 6b73616d20414d44 [ 248.030822] x13: 20666f20382b3037 x12: 3833386531353030 [ 248.030832] x11: 3038303030307830 x10: 0000000000000000 [ 248.030842] x9 : 0000000000000003 x8 : 00000000000001b4 [ 248.030851] x7 : 0000000000000001 x6 : 0000000000000001 [ 248.030861] x5 : 0000000000000000 x4 : 0000000000000001 [ 248.030870] x3 : 0000000000000006 x2 : 6eac74d7450f9a00 [ 248.030879] x1 : 6eac74d7450f9a00 x0 : 0000000000000000 [ 248.030889] Call trace: [ 248.030903] report_addr+0x38/0xa0 [ 248.030914] dma_direct_map_page+0x110/0x130 [ 248.030924] dma_direct_map_sg+0x78/0xe0 [ 248.030939] sunxi_mmc_request+0x70/0x4f0 [ 248.030952] __mmc_start_request+0x64/0x130 [ 248.030962] mmc_start_request+0x90/0xb8 [ 248.030973] mmc_wait_for_req+0x6c/0x100 [ 248.030985] mmc_io_rw_extended+0x250/0x2a8 [ 248.030996] sdio_io_rw_ext_helper+0x18c/0x230 [ 248.031007] sdio_memcpy_fromio+0x1c/0x28 [ 248.031072] sdio_data_read+0x1c/0x28 [xradio_wlan] [ 248.031118] __xradio_read+0x28/0x40 [xradio_wlan] [ 248.031166] xradio_reg_read+0x3c/0x60 [xradio_wlan] [ 248.031214] xradio_load_firmware+0x34/0xe18 [xradio_wlan] [ 248.031261] xradio_core_init+0x130/0x460 [xradio_wlan] [ 248.031308] sdio_probe+0x130/0x164 [xradio_wlan] [ 248.031321] sdio_bus_probe+0x12c/0x198 [ 248.031337] really_probe+0xdc/0x430 [ 248.031348] driver_probe_device+0xdc/0x130 [ 248.031358] device_driver_attach+0x6c/0x78 [ 248.031367] __driver_attach+0x9c/0x168 [ 248.031376] bus_for_each_dev+0x6c/0xc0 [ 248.031385] driver_attach+0x20/0x28 [ 248.031394] bus_add_driver+0x138/0x218 [ 248.031404] driver_register+0x60/0x110 [ 248.031414] sdio_register_driver+0x24/0x30 [ 248.031463] xradio_sdio_register+0x14/0x20 [xradio_wlan] [ 248.031510] xradio_core_entry+0xc/0x1000 [xradio_wlan] [ 248.031523] do_one_initcall+0x50/0x1a8 [ 248.031537] do_init_module+0x50/0x1f0 [ 248.031547] load_module+0x1f68/0x2510 [ 248.031558] __do_sys_finit_module+0xac/0x110 [ 248.031568] __arm64_sys_finit_module+0x1c/0x28 [ 248.031583] el0_svc_common.constprop.0+0x68/0x160 [ 248.031594] el0_svc_handler+0x20/0x80 [ 248.031603] el0_svc+0x8/0x1fc [ 248.031610] ---[ end trace d07a211fb8606773 ]--- [ 248.031628] sunxi-mmc 1c10000.mmc: dma_map_sg failed [ 248.031637] sunxi-mmc 1c10000.mmc: map DMA failed [ 248.031662] xradio WRN: FWIO: can't read config register, err=-12. [ 248.043881] xradio PM-DEV: xradio_pm_release root@orangepizeroplus:/home/orangepi# rmmod xradio_wlan.ko rmmod: ERROR: Module xradio_wlan is in use root@orangepizeroplus:/home/orangepi# can give me some hints of clues to solve the problem ? thx.

Tried both Debian and Ubuntu based 23.5 releases on my v1.4 board Boot process stops at "Starting kernel..." Also tried the "minimal CLI" debian release with same results. The previous versions 23.02 are fine. ▒ U-Boot SPL 2022.07-armbian (May 27 2023 - 19:26:49 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (May 27 2023 - 19:26:49 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB Core: 65 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: serial Net: phy interface1 eth0: ethernet@1c30000 starting USB... Bus usb@1c1a000: USB EHCI 1.00 Bus usb@1c1a400: USB OHCI 1.0 Bus usb@1c1b000: USB EHCI 1.00 Bus usb@1c1b400: USB OHCI 1.0 Bus usb@1c1c000: USB EHCI 1.00 Bus usb@1c1c400: USB OHCI 1.0 scanning bus usb@1c1a000 for devices... 1 USB Device(s) found scanning bus usb@1c1a400 for devices... 1 USB Device(s) found scanning bus usb@1c1b000 for devices... 1 USB Device(s) found scanning bus usb@1c1b400 for devices... 1 USB Device(s) found scanning bus usb@1c1c000 for devices... 1 USB Device(s) found scanning bus usb@1c1c400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Autoboot in 1 seconds, press <Space> to stop switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 4121 bytes read in 3 ms (1.3 MiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 184 bytes read in 3 ms (59.6 KiB/s) 15848831 bytes read in 658 ms (23 MiB/s) 8477464 bytes read in 355 ms (22.8 MiB/s) Found mainline kernel configuration 35377 bytes read in 7 ms (4.8 MiB/s) 504 bytes read in 6 ms (82 KiB/s) Applying kernel provided DT overlay sun8i-h3-usbhost2.dtbo 504 bytes read in 6 ms (82 KiB/s) Applying kernel provided DT overlay sun8i-h3-usbhost3.dtbo 617 bytes read in 6 ms (99.6 KiB/s) Applying kernel provided DT overlay sun8i-h3-tve.dtbo 4185 bytes read in 6 ms (680.7 KiB/s) Applying kernel provided DT fixup script (sun8i-h3-fixup.scr) ## Executing script at 45000000 Kernel image @ 0x42000000 [ 0x000000 - 0x815b18 ] ## Loading init Ramdisk from Legacy Image at 43400000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 15848767 Bytes = 15.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 EHCI failed to shut down host controller. Loading Ramdisk to 490e2000, end 49fff53f ... OK Loading Device Tree to 49071000, end 490e1fff ... OK Starting kernel ...

Thought this might be useful: FROM: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=2236 01 3.3V 02 5V 03 TWI0-SDA PA12 04 5V 05 TWI0-SCK PA11 06 GND 07 PWM1 PA06 08 UART1_TX PG06 09 GND 10 UART1_RX PG07 11 UART2_RX PA01 12 SIM_CLK/PA_EINT7 PA07 13 UART2_TX PA00 14 GND 15 UART2_CTS PA03 16 TWI1-SDA PA19 17 3.3V 18 TWI1-SCK PA18 19 SPI1_MOSI PA15 20 GND 21 SPI1_MISO PA16 22 UART2_RTS PA02 23 SPI1_CLK PA14 24 SPI1_CS PA13 25 GND 26 SIM_DET/PA_EINT10 PA10 FROM OFFICIAL USER MANUAL: https://drive.google.com/drive/folders/1lrtE6lbpXqxXTMmq7IxROOaZbOQ0U8uP P01 VCC-3V3 P02 VCC-5V P03 TWI0-SDA PA12 P04 VCC-5V P05 TWI0-SCK PA11 P06 GND P07 PWM1 PA6 P08 UART2_TX PA0 P09 GND P10 UART2_RX PA1 P11 S-TWI-SCK PL0 P12 PD11 P13 S-TWI-SDA PL1 P14 GND P15 UART2_CTS PA3 P16 TWI1-SDA PA19 P17 VCC3V3-EXT P18 TWI1-SCK PA18 P19 SPI1_MOSI PA15 P20 GND P21 SPI1_MISO PA16 P22 UART2_RTS PA2 P23 SPI1_CLK PA14 P24 SPI1_CS PA13 P25 GND P26 PD14 So you can make ~/bin/pinout-orange-pi-zero, and ~/bin/pinout containing: #!/bin/bash cat ~/bin/pinout-orange-pi-zero ... or just "~/bin/pinout": #!/bin/bash echo "text text text" ...so you'll have a pinout command like a Raspberry Pi. I have confirmed that pin 10 should be PG07, pin 12 should be PA07 and pin 26 should be PA10 for a DS18B20 temperature sensor with armbianEnv.txt like: $ cat /boot/armbianEnv.txt --- param_w1_pin=PA07 So it looks like the picture from Orange Pi forums is more accurate. Can anyone comment on the differences between the two pinouts eg pin 10, 12, 26, and others? Thanks, and thanks for making Armbian, and firstpost. Also warning, for other noobs (could have saved me several hours): "Armbian 23.5 Jammy" is broken! Click "Archived versions for reference and troubleshooting" on the download page and download "Armbian_23.02.2_Orangepizero_jammy_current_5.15.93.img.xz" instead

ls /sys/class/udc > UDC ls:write error: Device or resource busy I'm trying to get an armbian device (banana pi m2 zero and/or the orange pi zero LTS) to function as a USB client, but I can't seem to get the above step working. Any suggestions? lsof UDC returns nothing. On the RaspberryPI 4 this worked without issue

on orange pizero ,i installed pm-utils and with the pm-suspend command i put it in suspend . If I try to wake it up , with etherwake or other WOL programs (which send magic packets in LAN to the pizero's macadress) the pizero will not wake up . Do you know any tricks?

Hello, I'm trying to enable I2C access in U-Boot, for orange PI zero. I've downloaded the Armbian build, and tried to compile with CREATE_PATCHES, exactly like the tutorial here: https://zuckerbude.org/armbian-using-create-patches/ However, the build never stops and waits for me to make changes. I've attached the build log. I *think* I just need to add the following lines to orangepi_zero_defconfig: CONFIG_I2C0_ENABLE=y CONFIG_I2C1_ENABLE=y I guess that would be my next question- is this the proper way to change this config is via CREATE_PATCHES? I tried just changing the defconfig file and re-running compile.sh, but that didn't seem to help. Thanks in advance! build.log

Hi, This will be my first time using Armbian and OrangePi, sorry if theres stupid questions. I want to write a C++ application that uses LVGL to display information on a USB screen and have a few questions. 1) Will I be able to this screen in this setup. It uses the frame buffer (/dev/fb0). There are instructions for RaspberryPi, where its just plugged in and the frame buffer is available to use. 2) If I just use the latest Armbian Ubuntu version for this board what is the newest version of C++ I can use? (C++11/14/17 etc) 3) Is there a tool chain available to be able to cross compile my application (specifically from MacOS) then put the binary on the OrangePi? Or will I have to use something like docker and build for ARM? Thanks!

Hi , I am trying to install headers on my orang pi using command #apt install linux-headers-$(uname -r) getting the following message Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-headers-5.4.27-sunxi E: Couldn't find any package by glob 'linux-headers-5.4.27-sunxi' E: Couldn't find any package by regex 'linux-headers-5.4.27-sunxi' could someone help me in how do I install headers ?, I am trying to comiple a kernel module. thanks