1 1
Gabriel

Clearfog Pro-A1 revision-2.1 + Marvel 88SE9215

Recommended Posts

Armbianmonitor:

 

Hi everyone,

 

My name is Gabriel and I am a new person in the community.

 

After installing ARMBIAN (Armbian_5.91_Clearfogbase_Debian_stretch_default_4.14.135) with the Mini PCI Express Marvel 88SE9215, I got a problem with my Clearfog Pro-A1 revision-2.1. It did not work properly like 88SE9215 did not show me my disks. My Idea is to deploy my NAS server with OMV.

I tried to compile the kernel so many times with different modules like SATA, PATA, and AHCI but it did not work also. I guess that my u-boot is not setup properly because I was reading a couple post about it and it’s working to everyone.

 

Someone can give me a favor pls and tell me your ideas to try to solve that problem

 

Thanks.

 

Logs:

 

Armbianmonitor:  http://ix.io/201C

 

root@clearfogbase:~# lspci

00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6828 (rev 0a)

00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6828 (rev 0a)

02:00.0 SATA controller: Marvell Technology Group Ltd. Device 9215 (rev 11)

 

root@clearfogbase:~# lspci -nv

00:02.0 0604: 11ab:6828 (rev 0a) (prog-if 00 [Normal decode])

        Flags: fast devsel

        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0

        Prefetchable memory behind bridge: 00000000-000fffff

        Capabilities: [40] Express Root Port (Slot+), MSI 00

        Capabilities: [100] Advanced Error Reporting

00:03.0 0604: 11ab:6828 (rev 0a) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0

        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0

        I/O behind bridge: 00010000-00010fff

        Memory behind bridge: e0000000-e00fffff

        Prefetchable memory behind bridge: 00000000-000fffff

        Capabilities: [40] Express Root Port (Slot+), MSI 00

        Capabilities: [100] Advanced Error Reporting

02:00.0 0106: 1b4b:9215 (rev 11) (prog-if 01 [AHCI 1.0])

        Subsystem: 1b4b:9215

        Flags: bus master, fast devsel, latency 0, IRQ 53

        I/O ports at 10020

  I/O ports at 10030

        I/O ports at 10028

        I/O ports at 10034

        I/O ports at 10000

        Memory at e0040000 (32-bit, non-prefetchable)

        Expansion ROM at e0000000

        Capabilities: [40] Power Management version 3

        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-

        Capabilities: [70] Express Legacy Endpoint, MSI 00

        Capabilities: [e0] SATA HBA v0.0

        Capabilities: [100] Advanced Error Reporting

        Kernel driver in use: ahci

 

Booting from Clearfog 

       

U-Boot SPL 2018.01-02337-gdc4398fdb8 (May 14 2018 - 19:03:16)

High speed PHY - Version: 2.0

Detected Device ID 6828

board SerDes lanes topology details:

 | Lane #  | Speed |  Type       |

 --------------------------------

 |   0    |  3   |  SATA0       |

 |   1    |  0   |  SGMII1      |

 |   2    |  5   |  PCIe1       |

 |   3    |  5   |  USB3 HOST1  |

 |   4    |  5   |  PCIe2       |

 |   5    |  0   |  SGMII2      |

 --------------------------------

PCIe, Idx 1: detected no link

PCIe, Idx 2: detected no link

High speed PHY - Ended Successfully

DDR3 Training Sequence - Ver TIP-1.29.0

DDR3 Training Sequence - Switching XBAR Window to FastPath Window

DDR3 Training Sequence - Ended Successfully

Trying to boot from SPI

 

U-Boot 2018.01-02337-gdc4398fdb8 (May 14 2018 - 19:03:16 +0200), Build: jenkins-u-boot-clearfog-model=pro,variant=spi-10

SoC:   MV88F6828-?? (a) at 1600 MHz

DRAM:  1 GiB (800 MHz, 32-bit, ECC not enabled)

MMC:   mv_sdh: 0

SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB

Model: SolidRun Clearfog

Board: SolidRun ClearFog Pro

SCSI:  SATA link 0 timeout.

AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode

Net:   eth1: ethernet@70000, eth2: ethernet@30000, eth3: ethernet@34000

Hit any key to stop autoboot:  0

switch to partitions #0, OK

mmc0(part 0) is current device

** No partition table - mmc 0 **

starting USB...

USB0:   Register 2000120 NbrPorts 2

Starting the controller

USB XHCI 1.00

scanning bus 0 for devices... 1 USB Device(s) found

       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: device type unknown

... is now current device

** Bad device usb 0 **

** Bad device usb 0 **

scanning bus for devices...

Found 0 device(s).

 

 

Share this post


Link to post
Share on other sites

Hey 

 

there are multiple things you need to check. 

 

Are you using Clearfog Pro or Base? In the title you write Pro but from the Logs it looks like you are using a Base image. This might cause problems.

 

Apart from that check the position of the mPCIe card vs. the kernel and uboot you are using. Use this table as a guide: https://docs.google.com/spreadsheets/d/1VggzrfFibH0cmpSGW2FyoJW-d936Y2amwwKutUwX4-8/edit#gid=0

 

 

 

Greetings,

count-doku

Share this post


Link to post
Share on other sites
22 hours ago, Gabriel said:

U-Boot 2018.01-02337-gdc4398fdb8 (May 14 2018 - 19:03:16 +0200), Build: jenkins-u-boot-clearfog-model=pro,variant=spi-10


This is not our boot loader. You need updated one and did you try with kernel 4.19.y? 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
1 1