Jump to content

fbtft on 5.3.9 kernel


dittohead

Recommended Posts

Have a orange pi pc plus with 3.5inch RPi LCD (A)

I install bionic 5.3.9 and try to set up screen via this guide, but got this (dmesg |grep fbtft):

[    5.594066] fbtft: module is from the staging directory, the quality is unknown, you have been warned.
[    5.612714] fbtft_device: module is from the staging directory, the quality is unknown, you have been warned.
[    5.613364] fbtft_device: unknown parameter 'gpios' ignored
[    6.010096] Modules linked in: fb_ili9486(C+) sch_fq_codel fbtft_device(C) fbtft(C) ip_tables x_tables pwrseq_simple sy8106a_regulator
[    6.042799] LR is at fbtft_register_framebuffer+0x6f/0x1bc [fbtft]
[    6.099269] [<bf81fbe7>] (fbtft_register_framebuffer [fbtft]) from [<bf820593>] (fbtft_probe_common+0x103/0x360 [fbtft])
[    6.099291] [<bf820593>] (fbtft_probe_common [fbtft]) from [<bf813125>] (fbtft_driver_probe_spi+0x19/0x1c [fb_ili9486])
[    6.099313] [<bf813125>] (fbtft_driver_probe_spi [fb_ili9486]) from [<c06c1821>] (spi_drv_probe+0x55/0x68)
[    6.099404] [<c0660689>] (driver_register) from [<bf805017>] (fbtft_driver_module_init+0x17/0x1000 [fb_ili9486])
[    6.099420] [<bf805017>] (fbtft_driver_module_init [fb_ili9486]) from [<c0102beb>] (do_one_initcall+0x37/0x1a8)


On one of some previous build screen works after assigment as main screen. Now - I down't know what to do next

I swap screens from my RPI fligtfeeder - screen works fine

HDMI to external monitor works fine

Any ideas?

Edited by dittohead
fix topic
Link to comment
Share on other sites

install 5.83 xenial: all works

[    9.681206] fbtft_device:  SPI devices registered:
[    9.681229] fbtft_device:      spidev spi0.0 33000kHz 8 bits mode=0x00
[    9.681242] fbtft_device:  'fb' Platform devices registered:
[    9.681320] fbtft_device: Deleting spi0.0
[    9.681732] fbtft_device:  GPIOS used by 'piscreen':
[    9.681743] fbtft_device:    'reset' = GPIO2
[    9.681751] fbtft_device:    'dc' = GPIO71
[    9.681758] fbtft_device:  SPI devices registered:
[    9.681769] fbtft_device:      fb_ili9486 spi0.0 16000kHz 8 bits mode=0x00

some problem in new builds
 

Link to comment
Share on other sites

2 minutes ago, dittohead said:

and think that fbtft not support on github


Hmm, I don't know how their support is organised and if it exists at all. But usually author driver/maintainer/their GitHub is IMO the best source. 

Link to comment
Share on other sites

14 minutes ago, dittohead said:

armbianEnv.txt

 

Waveshare corporation does not support Armbian and vice versa. DT support for those display does not exists. Somebody has to make overlays. Then it becomes simple.

Link to comment
Share on other sites

4 minutes ago, Igor said:

 

Waveshare corporation does not support Armbian and vice versa. DT support for those display does not exists. Somebody has to make overlays. Then it becomes simple.

So for now no solution for 5.3 kernel and waweshare? Only roll to previous kernel?

Link to comment
Share on other sites

37 minutes ago, dittohead said:

So for now no solution for 5.3 kernel and waweshare? Only roll to previous kernel?

 

3rd party hardware was never supported because this is simply not possible to provide. It's your problem.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines