psxsnake Posted April 1, 2020 Share Posted April 1, 2020 I did update: it works with update inside menu of android tv box, but not install, it's like live distro only on SD can i make it permanent on box? sorry for my english is not my native language Link to comment Share on other sites More sharing options...
malloc32 Posted April 8, 2020 Share Posted April 8, 2020 Hello, I use my H96 Pro+ 3GB (S912) for many things, "download station", VPN, hosting .... all these work fine, but... I have the H96 connected to a televison and sometimes I like to play some games. I have installed mame, it works, but I have to reduce the resolution if I want to play at decent speed, but some games (Golden Axe) has a very very low frame rate. The H96 moves very well Golden Axe in Android, so I supose that there is a problem with mali drivers, no? Any solution? I have tried to install retropie from its git repository but not works. I have installed a MSX emulator and it works, but again I have to reduce the resolution and even with the lowest resolution not works at full speed. I have installed in sd Bionic 5.5.0-rc6-aml-s9xxx, works very well, but very very slow in mame. Note: if I disabled cores 4-7 works better, but it is not enough, still slow even at lowest resolution Thank you. Link to comment Share on other sites More sharing options...
Eduard Posted April 9, 2020 Share Posted April 9, 2020 Hi I tried to install de bionic_current_5.5.0 in my H96+ S912 Armlogic Mali 820 3G but I couldn't find the right dtb file. Can anybody help me? Thanks Link to comment Share on other sites More sharing options...
Nikeb Posted May 28, 2020 Share Posted May 28, 2020 Hi , same issue here, i tried some dtb , i can manage to make it run but the ethernet and wifi doesn't work (it's not blinking), it detects some eth0 but can't connect (even on boot is not blinkin anything). I m using a Beelink Ultimate GT1 (s912 3 gb) i m running 5.7.0-rc1-arm-64 bionic desktop Armbian_20.05.2_Arm-64_bionic_current_5.7.0-rc1_desktop_20200423 the dtb i use is gtx-200 if i recall good. It's like the eth0 it's been recognized (but not entirely) but even forcing a good IP it's not connecting/blinking. This is the sudo ethtool eth0 Settings for eth0: Supported ports: [TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: Unknown! Duplex: Unknown! (255) Port: MII PHYAD: 8 Transceiver: internal Auto-negotiation: on Supports Wake-on: ug Wake-on: d Current message level: 0x0000003f (63) dry probe link time ifdown ifup Link detected: no What should i do to make it work? Would be easier if i change the image? i try some but whenever i manage to make it run the eth0 (and wifi) doesn t work. Thanks for any suggestion. Link to comment Share on other sites More sharing options...
cedd-77 Posted July 5, 2020 Share Posted July 5, 2020 On 5/28/2020 at 10:27 AM, Nikeb said: Hi , same issue here, i tried some dtb , i can manage to make it run but the ethernet and wifi doesn't work (it's not blinking), it detects some eth0 but can't connect (even on boot is not blinkin anything). I m using a Beelink Ultimate GT1 (s912 3 gb) i m running 5.7.0-rc1-arm-64 bionic desktop Armbian_20.05.2_Arm-64_bionic_current_5.7.0-rc1_desktop_20200423 the dtb i use is gtx-200 if i recall good. It's like the eth0 it's been recognized (but not entirely) but even forcing a good IP it's not connecting/blinking. This is the sudo ethtool eth0 meson-gxm-vega-s96.dtb Settings for eth0: Supported ports: [TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: Unknown! Duplex: Unknown! (255) Port: MII PHYAD: 8 Transceiver: internal Auto-negotiation: on Supports Wake-on: ug Wake-on: d Current message level: 0x0000003f (63) dry probe link time ifdown ifup Link detected: no What should i do to make it work? Would be easier if i change the image? i try some but whenever i manage to make it run the eth0 (and wifi) doesn t work. Thanks for any suggestion. hello, I don't have the ultimate version of GT1 but I use the meson-gxm-vega-s96.dtb everything ok and ETH0 ! Just the CPU Temp at 55° but the box work great (home-asssitant). Link to comment Share on other sites More sharing options...
Recommended Posts