Jump to content

Helios64 - Feature Support Status


aprayoga

Recommended Posts

CURRENT branch (Linux Kernel 5.10)
Feature Support Status Remarks
Shutdown OK  
Reboot OK  
Suspend to RAM Not Supported USB host controller refuses to enter suspend mode
2.5G Ethernet
(2.5G speed)
OK

TX offload disabled by default, can be enabled for better performance

2.5G Ethernet
(1G speed)
Performance issue

Requires hardware fix.

Main Power/UPS status OK

Status can be read from sysfs

Battery Charging OK Status can be read from sysfs

UPS configuration

OK Auto shutdown after 10 min of power loss.
USB Type C - Host OK use dwc3-0-host overlay. Enable P13 jumper to be able to use USB 2.0 device.
USB Type C - Gadget OK use overlay to enable USB device mode. refer to this link
USB Type C - DisplayPort OK  
eMMC Boot OK  
SPI Boot Not Supported  
Recovery Button OK To use maskrom, jumper P13 must be enabled.
USB LED Not Supported usbport led trigger does not support activity and only works with USB 2.0 device
LAN LED OK

 default to eth0 activity

Wake On LAN Not Supported Suspend still have issue

 

Armbian 21.02

Edited by aprayoga
Update to Armbian 21.02
Link to comment
Share on other sites

LEGACY branch (Linux Kernel 4.4)
Feature Support Status Remarks
Shutdown Partial Fails to shutdown PMIC and triggers crash, HDD already parked
Reboot Partial

Similar like shutdown but Watchdog triggers the reboot so it appears successful

Suspend to RAM Not Supported Fails to resume operation after wake up
2.5G Ethernet
(2.5G speed)
OK  
2.5G Ethernet
(1G speed)
Performance issue Requires hardware fix.
Main Power/UPS Status OK Status can be read from sysfs
Battery Charging Status Not Supported  
UPS configuration OK

Auto shutdown after 10 min of power loss.

USB Type C - Host OK  
USB Type C - Gadget OK Use g_mass_storage kernel module
USB Type C - DisplayPort OK  
eMMC Boot OK  
SPI Boot Not Supported  
Recovery Button OK

To use maskrom, jumper P13 must be enabled.

USB LED Not Supported  
LAN LED Not Supported  
Wake On LAN Not Supported

Suspend still have issue

     

 

Armbian 21.02

Edited by aprayoga
Update to Armbian 21.02
Link to comment
Share on other sites

CURRENT branch (Linux Kernel 5.10)
Feature Support Status Remarks
Shutdown OK  
Reboot OK  
Suspend to RAM Not Supported USB host controller refuses to enter suspend mode
2.5G Ethernet
(2.5G speed)
OK

TX offload disabled by default, can be enabled for better performance

2.5G Ethernet
(1G speed)
Performance issue

Requires hardware fix.

Main Power/UPS status OK

Status can be read from sysfs

Battery Charging OK Status can be read from sysfs

UPS configuration

OK Auto shutdown after 10 min of power loss.
USB Type C - Host OK use dwc3-0-host overlay. Enable P13 jumper to be able to use USB 2.0 device.
USB Type C - Gadget OK use overlay to enable USB device mode. refer to this link
USB Type C - DisplayPort OK  
eMMC Boot OK  
SPI Boot Not Supported  
Recovery Button OK To use maskrom, jumper P13 must be enabled.
USB LED Not Supported usbport led trigger does not support activity and only works with USB 2.0 device
LAN LED Supported  default to eth0 activity
Wake On LAN Not Supported Suspend still have issue

 

Armbian 21.02

 

Note:

- UPS action will be changed into based on battery voltage threshold rather than countdown timer. (PR 2259)

- To change LAN LED network device, change eth0 on /etc/systemd/system/helios64-heartbeat-led.service at line 9 into eth1

 

Link to comment
Share on other sites

  • Igor unpinned this topic
Guest
This topic is now closed to further replies.
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines