Jump to content

Reboot not working properly with OMV


mortomanos

Recommended Posts

During installing Helios64 with the latest image I experienced several times that the system did not come up. Now that it is fully installed with OMV enabled, I sometimes do a reboot, and the system does not come up. Unfortunately I cannot see anything on the console level (on MacOS). After pressing the reboot button (around one or two times) the system comes up as nothing happened ever. What can I do to have the system reboot in a stable manner? Since it will sit in the basement soon, I don't want to run down every time I see that it does not reboot properly.

Link to comment
Share on other sites

  • gprovost changed the title to Reboot not working properly with OMV
On 12/8/2020 at 10:31 AM, aprayoga said:

@mortomanos Did you manage to see the problem in serial console?

 

Today is public holiday so I had a little bit of time to check some things. I today needed to reboot several times with the reboot button, before the system came up. The serial console stopped always at "Starting kernel ..."

 

The system LED stays blue, the hard disks spin up and each LED flashes a few times, then all attached disks flash together 5-6 times. Then all HDD LEDs stay blue. The LAN LED does not show up.

When pressing the reboot button the console instantly outputs some messages, and the new boot sequence starts. Then again all LEDs stay blue and nothing happens (at "Starting kernel ...").

 

In the log itself there are a few messages that I think are not relevant, but I'll attach them here:

Spoiler

 


DDR Version 1.24 20191016
In
channel 0
CS = 0
MR0=0x18
MR4=0x2
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
256B stride
channel 0
CS = 0
MR0=0x18
MR4=0x2
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x18
MR4=0x82
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
change freq to 856MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x40
ch 1 ddrconfig = 0x101, ddrsize = 0x40
pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD
ddr_set_rate to 328MHZ
ddr_set_rate to 666MHZ
ddr_set_rate to 928MHZ
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
ddr_set_rate to 416MHZ, ctl_index 0
ddr_set_rate to 856MHZ, ctl_index 1
support 416 856 328 666 928 MHz, current 856MHz
OUT
Boot1: 2019-03-14, version: 1.19
CPUId = 0x0
ChipType = 0x10, 253
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=14910MB
FwPartOffset=2000 , 100000
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
SdmmcInit=0 1
StorageInit ok = 67874
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT 0x3380ec0 signature is wrong
recovery gpt...
GPT 0x3380ec0 signature is wrong
recovery gpt fail!
LoadTrust Addr:0x4000
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xdd6b0
RunBL31 0x40000
NOTICE:  BL31: v1.3(debug):42583b6
NOTICE:  BL31: Built : 07:55:13, Oct 15 2019
NOTICE:  BL31: Rockchip release version: v1.1
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    plat_rockchip_pmu_init(1190): pd status 3e
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9
 
 
U-Boot 2020.07-armbian (Nov 27 2020 - 21:56:51 +0100)
 
SoC: Rockchip rk3399
Reset cause: POR
DRAM:  3.9 GiB
PMIC:  RK808
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
MMC:   mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
 
In:    serial
Out:   serial
Err:   serial
Model: Helios64
Revision: 1.2 - 4GB non ECC
Net:   eth0: ethernet@fe300000
scanning bus for devices...
Hit any key to stop autoboot:  0
Card did not respond to voltage select!
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3185 bytes read in 19 ms (163.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
166 bytes read in 15 ms (10.7 KiB/s)
16609681 bytes read in 1596 ms (9.9 MiB/s)
27574784 bytes read in 2640 ms (10 MiB/s)
81670 bytes read in 41 ms (1.9 MiB/s)
2698 bytes read in 32 ms (82 KiB/s)
Applying kernel provided DT fixup script (rockchip-fixup.scr)
## Executing script at 09000000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    16609617 Bytes = 15.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f4f0f000, end f5ee6151 ... OK
   Loading Device Tree to 00000000f4e92000, end 00000000f4f0efff ... OK
 
Starting kernel ...

 

Edited by aprayoga
Add spoiler
Link to comment
Share on other sites

On 12/9/2020 at 12:58 AM, aprayoga said:

@mortomanos do you have other Linux system ? edit the boot/armbianEnv.txt and add


extraargs=ignore_loglevel

 

 

That did the trick getting kernel messages.

 

The boot hangs somewhere after md0 is found:

 

Spoiler

U-Boot 2020.07-armbian (Nov 27 2020 - 21:56:51 +0100)
 
SoC: Rockchip rk3399
Reset cause: RST
DRAM:  3.9 GiB
PMIC:  RK808
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
MMC:   mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
 
In:    serial
Out:   serial
Err:   serial
Model: Helios64
Revision: 1.2 - 4GB non ECC
Net:   eth0: ethernet@fe300000
scanning bus for devices...
Hit any key to stop autoboot:  0
Card did not respond to voltage select!
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3185 bytes read in 19 ms (163.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
192 bytes read in 15 ms (11.7 KiB/s)
16609681 bytes read in 1596 ms (9.9 MiB/s)
27574784 bytes read in 2640 ms (10 MiB/s)
81670 bytes read in 40 ms (1.9 MiB/s)
2698 bytes read in 32 ms (82 KiB/s)
Applying kernel provided DT fixup script (rockchip-fixup.scr)
## Executing script at 09000000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    16609617 Bytes = 15.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f4f0f000, end f5ee6151 ... OK
   Loading Device Tree to 00000000f4e92000, end 00000000f4f0efff ... OK
 
Starting kernel ...
 
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.9.11-rockchip64 (root@beast) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 9.2.1 20191025, GNU ld (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 2.33.1.20191209) #20.11.1 SMP PREEMPT Fri Nov 27 21:59:08 CET 2020
[    0.000000] Machine model: Helios64
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 128 MiB at 0x00000000ecc00000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xf77d9100-0xf77dafff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000200000-0x000000003fffffff]
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000f7ffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] On node 0 totalpages: 1015296
[    0.000000]   DMA zone: 4088 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 261632 pages, LIFO batch:63
[    0.000000]   DMA32 zone: 11776 pages used for memmap
[    0.000000]   DMA32 zone: 753664 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 32 pages/cpu s93784 r8192 d29096 u131072
[    0.000000] pcpu-alloc: s93784 r8192 d29096 u131072 alloc=32*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 999432
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: root=UUID=a60f3956-17d4-4744-bc2b-021293160020 rootwait rootfstype=ext4 console=ttyS2,1500000 console=tty1 consoleblank=0 loglevel=1 ubootpart=92c32d3c-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u ignore_loglevel  cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x3bfff000-0x3ffff000] (64MB)
[    0.000000] Memory: 3739552K/4061184K available (14528K kernel code, 2096K rwdata, 5992K rodata, 4224K init, 575K bss, 190560K reserved, 131072K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[    0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @f6d00000 (flat, esz 8, psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GICv3: using LPI property table @0x00000000f6cb0000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000000f6cc0000
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] random: get_random_bytes called from start_kernel+0x690/0x848 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001426] Console: colour dummy device 80x25
[    0.002540] printk: console [tty1] enabled
[    0.002681] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002721] pid_max: default: 32768 minimum: 301
[    0.002887] LSM: Security Framework initializing
[    0.002947] Yama: becoming mindful.
[    0.003107] AppArmor: AppArmor initialized
[    0.003212] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.003264] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.006509] rcu: Hierarchical SRCU implementation.
[    0.007714] Platform MSI: interrupt-controller@fee20000 domain created
[    0.008281] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.010643] EFI services will not be available.
[    0.011356] smp: Bringing up secondary CPUs ...
[    0.012492] Detected VIPT I-cache on CPU1
[    0.012540] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.012559] GICv3: CPU1: using allocated LPI pending table @0x00000000f6cd0000
[    0.012621] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.013985] Detected VIPT I-cache on CPU2
[    0.014031] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.014050] GICv3: CPU2: using allocated LPI pending table @0x00000000f6ce0000
[    0.014111] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.015456] Detected VIPT I-cache on CPU3
[    0.015502] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.015521] GICv3: CPU3: using allocated LPI pending table @0x00000000f6cf0000
[    0.015580] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.016977] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
[    0.016987] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.016995] Detected PIPT I-cache on CPU4
[    0.017028] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.017042] GICv3: CPU4: using allocated LPI pending table @0x00000000f6d80000
[    0.017080] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[    0.018273] Detected PIPT I-cache on CPU5
[    0.018309] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.018324] GICv3: CPU5: using allocated LPI pending table @0x00000000f6d90000
[    0.018362] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[    0.018529] smp: Brought up 1 node, 6 CPUs
[    0.018909] SMP: Total of 6 processors activated.
[    0.018932] CPU features: detected: 32-bit EL0 Support
[    0.018954] CPU features: detected: CRC32 instructions
[    0.018977] CPU features: detected: 32-bit EL1 Support
[    0.047176] CPU: All CPU(s) started at EL2
[    0.047270] alternatives: patching kernel code
[    0.051035] devtmpfs: initialized
[    0.067765] Registered cp15_barrier emulation handler
[    0.067803] Registered setend emulation handler
[    0.068591] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.068678] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.071809] xor: measuring software checksum speed
[    0.108099]    8reg
                      [    3.035920] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.036525] ehci-pci: EHCI PCI platform driver
[    3.036961] ehci-platform: EHCI generic platform driver
[    3.039913] ehci-platform fe380000.usb: EHCI Host Controller
[    3.040443] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
[    3.041287] ehci-platform fe380000.usb: irq 30, io mem 0xfe380000
[    3.057514] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    3.058306] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    3.059046] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.059691] usb usb1: Product: EHCI Host Controller
[    3.060129] usb usb1: Manufacturer: Linux 5.9.11-rockchip64 ehci_hcd
[    3.060696] usb usb1: SerialNumber: fe380000.usb
[    3.061734] hub 1-0:1.0: USB hub found
[    3.062120] hub 1-0:1.0: 1 port detected
[    3.063270] ohci_hcd: USB 1.1 'Open' Hassigned bus number 2
[    3.066566] ohci-platform fe3a0000.usb: irq 31, io mem 0xfe3a0000
[    3.129714] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.09
[    3.130456] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.131101] usb usb2: Product: Generic Platform OHCI controller
[    3.131631] usb usb2: Manufacturer: Linux 5.9.11-rockchip64 ohci_hcd
[    3.132199] usb usb2: SerialNumber: fe3a0000.usb
[    3.133139] hub 2-0:1.0: USB hub found
[    3.133536] hub 2-0:1.0: 1 port detected
[    3.135436] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.135950] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3
[    3.136804] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[    3.137725] xhci-hcd xhci-hcd.0.auto: irq 228, io mem 0xfe900000
[    3.138674] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    3.139413] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.140059] usb usb3: Product: xHCI Host Controller
[    3.140497] usb usb3: Manufacturer: Linux 5.9.11-rockchip64 xhci-hcd
[    3.141064] usb usb3: SerialNumber: xhci-hcd.0.auto
[    3.142090] hub 3-0:1.0: USB hub found
[    3.142466] hub 3-0:1.0: 1 port detected
[    3.143159] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.143662] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4
[    3.144362] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    3.145015] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.145908] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    3.146646] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.147291] usb usb4: Product: xHCI Host Controller
[    3.147730] usb usb4: Manufacturer: Linux 5.9.11-rockchip64 xhci-hcd
[    3.148296] usb usb4: SerialNumber: xhci-hcd.0.auto
[    3.149244] hub 4-0:1.0: USB hub found
[    3.149667] hub 4-0:1.0: 1 port detected
[    3.150509] usbcore: registered new interface driver usb-storage
[    3.153634] mousedev: PS/2 mouse device common for all mice
[    3.155538] i2c /dev entries driver
[    3.159845] pca953x 2-0020: using no AI
[    3.170401] rk808 0-001b: chip id: 0x0
[    3.174664] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    3.175246] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    3.176901] vdd_center: supplied by vcc5v0_sys
[    3.177946] vdd_cpu_l: supplied by vcc5v0_sys
[    3.178677] vcc_ddr_s3: supplied by vcc5v0_sys
[    3.179772] vcc1v8_sys_s3: supplied by vcc5v0_sys
[    3.180679] vcc1v8_dvp: supplied by vcc5v0_sys
[    3.181597] vcc3v0_touch: supplied by vcc5v0_sys
[    3.183506] vcc1v8_s3: supplied by vcc5v0_sys
[    3.184178] vcc_sdio_s0: Bringing 3300000uV into 3000000-3000000uV
[    3.185877] vcc_sdio_s0: supplied by vcc5v0_sys
[    3.186785] vcca3v0_codec: supplied by vcc5v0_sys
[    3.188405] vcc1v5_s3: supplied by vcc5v0_sys
[    3.189319] vcca1v8_codec: supplied by vcc5v0_sys
[    3.190965] vcc3v0_s3: supplied by vcc5v0_sys
[    3.191512] vcc3v3_sys_s0: failed to get the current voltage(-517)
[    3.192080] vcc3v3_sys_s0: supplied by vcc3v3_sys_s3
[    3.193056] vcc3v3_s0: supplied by vcc3v3_sys_s3
[    3.197157] rk808-rtc rk808-rtc: registered as rtc0
[    3.198180] rk808-rtc rk808-rtc: setting system clock to 2020-12-20T15:49:14 UTC (1608479354)
[    3.202075] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    3.203782] vcc1v8_sys_s0: supplied by vcc1v8_sys_s3
[    3.204316] avdd_0v9_s0: supplied by vcc1v8_sys_s3
[    3.204854] vdd_cpu_b: supplied by vcc5v0_sys
[    3.208291] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    3.210050] vdd_gpu: supplied by vcc5v0_sys
[    3.219862] dw_wdt ff848000.watchdog: No valid TOPs array specified
[    3.222416] sdhci: Secure Digital Host Controller Interface driver
[    3.222974] sdhci: Copyright(c) Pierre Ossman
[    3.223388] Synopsys Designware Multimedia Card Interface Driver
[    3.225717] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
[    3.226383] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
[    3.226981] dwmmc_rockchip fe320000.mmc: Version ID is 270a
[    3.227541] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
[    3.228860] dwmmc_rockchip fe320000.mmc: Got CD GPIO
[    3.242216] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    3.254634] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.256913] mmc1: CQHCI version 5.10
[    3.282143] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    3.287136] ledtrig-cpu: registered to indicate activity on CPUs
[    3.288959] hid: raw HID events driver (C) Jiri Kosina
[    3.289652] usbcore: registered new interface driver usbhid
[    3.289755] random: fast init done
[    3.290159] usbhid: USB HID core driver
[    3.296745] drop_monitor: Initializing network drop monitor service
[    3.298188] NET: Registered protocol family 10
[    3.351947] mmc1: mmc_select_hs200 failed, error -110
[    3.352420] mmc1: error -110 whilst initialising MMC card
[    3.354399] Segment Routing with IPv6
[    3.354835] NET: Registered protocol family 17
[    3.355413] 8021q: 802.1Q VLAN Support v1.8
[    3.355848] Key type dns_resolver registered
[    3.356808] registered taskstats version 1
[    3.357189] Loading compiled-in X.509 certificates
[    3.361094] Loaded X.509 cert 'Build time autogenerated kernel key: cf582b85d37ac5e7e16062bd2222df75b99b261f'
[    3.362214] zswap: loaded using pool lzo/zbud
[    3.362962] Key type ._fscrypt registered
[    3.363329] Key type .fscrypt registered
[    3.363682] Key type fscrypt-provisioning registered
[    3.367191] Btrfs loaded, crc32c=crc32c-generic
[    3.393840] Key type encrypted registered
[    3.394222] AppArmor: AppArmor sha1 policy hashing enabled
[    3.443841] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges:
[    3.444518] rockchip-pcie f8000000.pcie:      MEM 0x00fa000000..0x00fbdfffff -> 0x00fa000000
[    3.445285] rockchip-pcie f8000000.pcie:       IO 0x00fbe00000..0x00fbefffff -> 0x00fbe00000
[    3.451319] mmc1: mmc_select_hs200 failed, error -110
[    3.451787] mmc1: error -110 whilst initialising MMC card
[    3.481516] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    3.502804] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
[    3.503403] pci_bus 0000:00: root bus resource [bus 00-1f]
[    3.503897] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff]
[    3.504514] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfbe00000-0xfbefffff])
[    3.505411] pci 0000:00:00.0: [1d87:0100] type 01 class 0x060400
[    3.506116] pci 0000:00:00.0: supports D1
[    3.506483] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    3.512449] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    3.513420] pci 0000:01:00.0: [197b:0585] type 00 class 0x010601
[    3.514040] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    3.514671] pci 0000:01:00.0: reg 0x10: [io  size 0x0080]
[    3.515184] pci 0000:01:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[    3.515813] pci 0000:01:00.0: reg 0x14: [io  size 0x0080]
[    3.516324] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[    3.516952] pci 0000:01:00.0: reg 0x18: [io  size 0x0080]
[    3.517463] pci 0000:01:00.0: reg 0x1c: initial BAR value 0x00000000 invalid
[    3.518100] pci 0000:01:00.0: reg 0x1c: [io  size 0x0080]
[    3.518611] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[    3.519238] pci 0000:01:00.0: reg 0x20: [io  size 0x0080]
[    3.519750] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x00001fff]
[    3.520337] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    3.520966] pci 0000:01:00.0: Max Payload Size set to 256 (was 128, max 512)
[    3.521920] pci 0000:01:00.0: PME# supported from D3hot
[    3.522632] pci 0000:01:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x2 link at 0000:00:00.0 (capable of 15.752 Gb/s with 8.0 GT/s PCIe x2 link)
[    3.529251] pci_bus 0000:01: busn_res: [bus 01-1f] end is updated to 01
[    3.529880] pci 0000:00:00.0: BAR 14: assigned [mem 0xfa000000-0xfa0fffff]
[    3.530503] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa00ffff pref]
[    3.531151] pci 0000:01:00.0: BAR 5: assigned [mem 0xfa010000-0xfa011fff]
[    3.531770] pci 0000:01:00.0: BAR 0: no space for [io  size 0x0080]
[    3.532330] pci 0000:01:00.0: BAR 0: failed to assign [io  size 0x0080]
[    3.532921] pci 0000:01:00.0: BAR 1: no space for [io  size 0x0080]
[    3.533495] pci 0000:01:00.0: BAR 1: failed to assign [io  size 0x0080]
[    3.534087] pci 0000:01:00.0: BAR 2: no space for [io  size 0x0080]
[    3.534646] pci 0000:01:00.0: BAR 2: failed to assign [io  size 0x0080]
[    3.535236] pci 0000:01:00.0: BAR 3: no space for [io  size 0x0080]
[    3.535795] pci 0000:01:00.0: BAR 3: failed to assign [io  size 0x0080]
[    3.536384] pci 0000:01:00.0: BAR 4: no space for [io  size 0x0080]
[    3.536943] pci 0000:01:00.0: BAR 4: failed to assign [io  size 0x0080]
[    3.537547] pci 0000:00:00.0: PCI bridge to [bus 01]
[    3.537999] pci 0000:00:00.0:   bridge window [mem 0xfa000000-0xfa0fffff]
[    3.538844] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    3.539710] pcieport 0000:00:00.0: PME: Signaling with IRQ 239
[    3.540568] pcieport 0000:00:00.0: AER: enabled with IRQ 239
[    3.541416] ahci 0000:01:00.0: version 3.0
[    3.541834] ahci 0000:01:00.0: enabling device (0000 -> 0002)
[    3.542904] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[    3.543590] ahci 0000:01:00.0: AHCI 0001.0301 32 slots 5 ports 6 Gbps 0x1f impl SATA mode
[    3.544322] ahci 0000:01:00.0: flags: 64bit ncq sntf stag pm led clo pmp fbs pio slum part ccc apst boh
[    3.550555] scsi host0: ahci
[    3.551507] scsi host1: ahci
[    3.552320] scsi host2: ahci
[    3.553139] scsi host3: ahci
[    3.553965] scsi host4: ahci
[    3.554464] ata1: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010100 irq 240
[    3.555136] ata2: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010180 irq 241
[    3.555805] ata3: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010200 irq 242
[    3.556472] ata4: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010280 irq 243
[    3.557140] ata5: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010300 irq 244
[    3.564253] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    3.567862] of_cfs_init
[    3.568124] of_cfs_init: OK
[    3.571221] mmc1: mmc_select_hs200 failed, error -110
[    3.571687] mmc1: error -110 whilst initialising MMC card
[    3.631572] usb 3-1: New USB device found, idVendor=2109, idProduct=2815, bcdDevice= 7.04
[    3.632307] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.632944] usb 3-1: Product: USB2.0 Hub
[    3.633397] usb 3-1: Manufacturer: VIA Labs, Inc.
[    3.689407] hub 3-1:1.0: USB hub found
[    3.689996] hub 3-1:1.0: 4 ports detected
[    3.734244] mmc1: mmc_select_hs200 failed, error -110
[    3.734706] mmc1: error -110 whilst initialising MMC card
[    3.784117] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[    3.902376] usb 4-1: New USB device found, idVendor=2109, idProduct=0815, bcdDevice= 7.04
[    3.903114] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.903751] usb 4-1: Product: USB3.0 Hub
[    3.904205] usb 4-1: Manufacturer: VIA Labs, Inc.
[    3.929276] hub 4-1:1.0: USB hub found
[    3.929774] hub 4-1:1.0: 4 ports detected
[    4.033551] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    4.036307] ata1.00: ATA-8: TOSHIBA HDWQ140, FJ1M, max UDMA/100
[    4.036850] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    4.039716] ata1.00: configured for UDMA/100
[    4.040832] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA HDWQ140  FJ1M PQ: 0 ANSI: 5
[    4.043246] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    4.044022] sd 0:0:0:0: [sda] Write Protect is off
[    4.044468] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.045042] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.060561] sd 0:0:0:0: [sda] Attached SCSI disk
[    4.489518] usb 3-1.4: new high-speed USB device number 3 using xhci-hcd
[    4.517529] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    4.639735] ata2.00: ATA-8: TOSHIBA HDWQ140, FJ1M, max UDMA/100
[    4.640291] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    4.643146] ata2.00: configured for UDMA/100
[    4.644149] scsi 1:0:0:0: Direct-Access     ATA      TOSHIBA HDWQ140  FJ1M PQ: 0 ANSI: 5
[    4.646323] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    4.647095] sd 1:0:0:0: [sdb] Write Protect is off
[    4.647543] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    4.648114] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.858420] sd 1:0:0:0: [sdb] Attached SCSI disk
[    5.121525] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    5.248706] ata3.00: ATA-8: TOSHIBA HDWQ140, FJ1M, max UDMA/100
[    5.249261] ata3.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    5.252139] ata3.00: configured for UDMA/100
[    5.253145] scsi 2:0:0:0: Direct-Access     ATA      TOSHIBA HDWQ140  FJ1M PQ: 0 ANSI: 5
[    5.255307] sd 2:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    5.256077] sd 2:0:0:0: [sdc] Write Protect is off
[    5.256524] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    5.257098] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.301654] usb 4-1.4: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[    5.322804] usb 4-1.4: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[    5.323565] usb 4-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    5.324230] usb 4-1.4: Product: USB 10/100/1G/2.5G LAN
[    5.324700] usb 4-1.4: Manufacturer: Realtek
[    5.325095] usb 4-1.4: SerialNumber: 000000001
[    5.469019] sd 2:0:0:0: [sdc] Attached SCSI disk
[    5.567956] ata4: SATA link down (SStatus 0 SControl 300)
[    6.045527] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    6.047961] ata5.00: ATA-9: SanDisk SSD PLUS 120GB, UE4500RL, max UDMA/133
[    6.048579] ata5.00: 234455040 sectors, multi 1: LBA48 NCQ (depth 32)
[    6.054445] ata5.00: configured for UDMA/133
[    6.055287] scsi 4:0:0:0: Direct-Access     ATA      SanDisk SSD PLUS 00RL PQ: 0 ANSI: 5
[    6.057599] sd 4:0:0:0: [sdd] 234455040 512-byte logical blocks: (120 GB/112 GiB)
[    6.058349] sd 4:0:0:0: [sdd] Write Protect is off
[    6.058797] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[    6.059370] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.065033] sd 4:0:0:0: [sdd] Attached SCSI disk
[    6.068478] Freeing unused kernel memory: 4224K
[    6.085635] Run /init as init process
[    6.085970]   with arguments:
[    6.086242]     /init
[    6.086452]   with environment:
[    6.086738]     HOME=/
[    6.086954]     TERM=linux
[    6.087202]     ubootpart=92c32d3c-01
[    6.087533]     cgroup_enable=memory
[    6.087856]     cgroup_memory=1
[    7.014772] input: adc-keys as /devices/platform/adc-keys/input/input1
[    7.097723] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
[    7.098334] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
[    7.099049] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[    7.099867] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    7.100504] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    7.101015] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
[    7.101562] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    7.102190] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    7.102812] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    7.108372] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    7.111912] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[    7.112620] rk_gmac-dwmac fe300000.ethernet:         DWMAC1000
[    7.113094] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
[    7.113781] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
[    7.114448] rk_gmac-dwmac fe300000.ethernet: COE Type 2
[    7.114916] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
[    7.115543] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[    7.116245] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[    7.116780] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[    7.117303] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    7.253679] libphy: stmmac: probed
[    7.254035] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    7.255170] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[    7.274696] async_tx: api initialized (async)
[    7.310723] md/raid:md0: device sda operational as raid disk 0
[    7.311278] md/raid:md0: device sdc operational as raid disk 2
[    7.311809] md/raid:md0: device sdb operational as raid disk 1
[    7.318041] md/raid:md0: raid level 5 active with 3 out of 3 devices, algorithm 2
[    7.481250] md0: detected capacity change from 0 to 8001302822912
[    9.123210] random: crng init done
[   33.761578] vcc3v0_sd: disabling
[   33.761886] vcc5v0_typec: disabling

After that - nothing is happening.

Edited by Werner
Add spoiler
Link to comment
Share on other sites

And a proper boot shows the following:

 

Spoiler

 
Starting kernel ...
 
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.9.11-rockchip64 (root@beast) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 9.2.1 20191025, GNU ld (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 2.33.1.20191209) #20.11.1 SMP PREEMPT Fri Nov 27 21:59:08 CET 2020
[    0.000000] Machine model: Helios64
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 128 MiB at 0x00000000ecc00000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xf77d9100-0xf77dafff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000200000-0x000000003fffffff]
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000f7ffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] On node 0 totalpages: 1015296
[    0.000000]   DMA zone: 4088 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 261632 pages, LIFO batch:63
[    0.000000]   DMA32 zone: 11776 pages used for memmap
[    0.000000]   DMA32 zone: 753664 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 32 pages/cpu s93784 r8192 d29096 u131072
[    0.000000] pcpu-alloc: s93784 r8192 d29096 u131072 alloc=32*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 999432
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: root=UUID=a60f3956-17d4-4744-bc2b-021293160020 rootwait rootfstype=ext4 console=ttyS2,1500000 console=tty1 consoleblank=0 loglevel=1 ubootpart=92c32d3c-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u ignore_loglevel  cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x3bfff000-0x3ffff000] (64MB)
[    0.000000] Memory: 3739552K/4061184K available (14528K kernel code, 2096K rwdata, 5992K rodata, 4224K init, 575K bss, 190560K reserved, 131072K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[    0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @f6d00000 (flat, esz 8, psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GICv3: using LPI property table @0x00000000f6cb0000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000000f6cc0000
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] random: get_random_bytes called from start_kernel+0x690/0x848 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001437] Console: colour dummy device 80x25
[    0.002553] printk: console [tty1] enabled
[    0.002694] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002734] pid_max: default: 32768 minimum: 301
[    0.002899] LSM: Security Framework initializing
[    0.002959] Yama: becoming mindful.
[    0.003121] AppArmor: AppArmor initialized
[    0.003225] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.003277] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.006538] rcu: Hierarchical SRCU implementation.
[    0.007719] Platform MSI: interrupt-controller@fee20000 domain created
[    0.008305] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.010661] EFI services will not be available.
[    0.011379] smp: Bringing up secondary CPUs ...
[    0.012519] Detected VIPT I-cache on CPU1
[    0.012566] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.012585] GICv3: CPU1: using allocated LPI pending table @0x00000000f6cd0000
[    0.012646] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.014007] Detected VIPT I-cache on CPU2
[    0.014053] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.014072] GICv3: CPU2: using allocated LPI pending table @0x00000000f6ce0000
[    0.014131] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.015467] Detected VIPT I-cache on CPU3
[    0.015511] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.015530] GICv3: CPU3: using allocated LPI pending table @0x00000000f6cf0000
[    0.015591] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.017047] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
[    0.017057] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.017065] Detected PIPT I-cache on CPU4
[    0.017098] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.017112] GICv3: CPU4: using allocated LPI pending table @0x00000000f6d80000
[    0.017151] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[    0.018340] Detected PIPT I-cache on CPU5
[    0.018376] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.018390] GICv3: CPU5: using allocated LPI pending table @0x00000000f6d90000
[    0.018430] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[    0.018597] smp: Brought up 1 node, 6 CPUs
[    0.018977] SMP: Total of 6 processors activated.
[    0.019001] CPU features: detected: 32-bit EL0 Support
[    0.019023] CPU features: detected: CRC32 instructions
[    0.019046] CPU features: detected: 32-bit EL1 Support
[    0.047234] CPU: All CPU(s) started at EL2
[    0.047328] alternatives: patching kernel code
[    0.051083] devtmpfs: initialized
[    0.067819] Registered cp15_barrier emulation handler
[    0.067857] Registered setend emulation handler
[    0.068690] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.068777] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.071901] xor: measuring software checksum speed
[    0.108155]    8reg
                      [    3.034047] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.034654] ehci-pci: EHCI PCI platform driver
[    3.035089] ehci-platform: EHCI generic platform driver
[    3.037731] ehci-platform fe380000.usb: EHCI Host Controller
[    3.038261] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
[    3.039106] ehci-platform fe380000.usb: irq 30, io mem 0xfe380000
[    3.053691] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    3.054506] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    3.055248] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.055894] usb usb1: Product: EHCI Host Controller
[    3.056332] usb usb1: Manufacturer: Linux 5.9.11-rockchip64 ehci_hcd
[    3.056900] usb usb1: SerialNumber: fe380000.usb
[    3.057893] hub 1-0:1.0: USB hub found
[    3.058269] hub 1-0:1.0: 1 port detected
[    3.059415] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.059984] ohci-pci: OHCI PCI platform driver
[    3.060434] ohci-platform: OHCI generic platform driver
[    3.061251] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    3.061893] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 2
[    3.062722] ohci-platform fe3a0000.usb: irq 31, io mem 0xfe3a0000
[    3.125900] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.09
[    3.126641] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.127287] usb usb2: Product: Generic Platform OHCI controller
[    3.127817] usb usb2: Manufacturer: Linux 5.9.11-rockchip64 ohci_hcd
[    3.128383] usb usb2: SerialNumber: fe3a0000.usb
[    3.129295] hub 2-0:1.0: USB hub found
[    3.129693] hub 2-0:1.0: 1 port detected
[    3.131587] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.132098] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3
[    3.132954] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[    3.133873] xhci-hcd xhci-hcd.0.auto: irq 228, io mem 0xfe900000
[    3.134825] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[    3.135567] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.136212] usb usb3: Product: xHCI Host Controller
[    3.136652] usb usb3: Manufacturer: Linux 5.9.11-rockchip64 xhci-hcd
[    3.137219] usb usb3: SerialNumber: xhci-hcd.0.auto
[    3.138211] hub 3-0:1.0: USB hub found
[    3.138587] hub 3-0:1.0: 1 port detected
[    3.139280] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.139783] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4
[    3.140476] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    3.141137] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.142033] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[    3.142771] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.143417] usb usb4: Product: xHCI Host Controller
[    3.143856] usb usb4: Manufacturer: Linux 5.9.11-rockchip64 xhci-hcd
[    3.144423] usb usb4: SerialNumber: xhci-hcd.0.auto
[    3.145339] hub 4-0:1.0: USB hub found
[    3.145762] hub 4-0:1.0: 1 port detected
[    3.146614] usbcore: registered new interface driver usb-storage
[    3.149741] mousedev: PS/2 mouse device common for all mice
[    3.151665] i2c /dev entries driver
[    3.155975] pca953x 2-0020: using no AI
[    3.167045] rk808 0-001b: chip id: 0x0
[    3.171240] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    3.171821] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    3.173456] vdd_center: supplied by vcc5v0_sys
[    3.174568] vdd_cpu_l: supplied by vcc5v0_sys
[    3.175293] vcc_ddr_s3: supplied by vcc5v0_sys
[    3.176343] vcc1v8_sys_s3: supplied by vcc5v0_sys
[    3.177260] vcc1v8_dvp: supplied by vcc5v0_sys
[    3.178192] vcc3v0_touch: supplied by vcc5v0_sys
[    3.180080] vcc1v8_s3: supplied by vcc5v0_sys
[    3.180770] vcc_sdio_s0: Bringing 3300000uV into 3000000-3000000uV
[    3.182479] vcc_sdio_s0: supplied by vcc5v0_sys
[    3.183378] vcca3v0_codec: supplied by vcc5v0_sys
[    3.184997] vcc1v5_s3: supplied by vcc5v0_sys
[    3.185913] vcca1v8_codec: supplied by vcc5v0_sys
[    3.187519] vcc3v0_s3: supplied by vcc5v0_sys
[    3.188054] vcc3v3_sys_s0: failed to get the current voltage(-517)
[    3.188621] vcc3v3_sys_s0: supplied by vcc3v3_sys_s3
[    3.189619] vcc3v3_s0: supplied by vcc3v3_sys_s3
[    3.193724] rk808-rtc rk808-rtc: registered as rtc0
[    3.194727] rk808-rtc rk808-rtc: setting system clock to 2020-12-20T15:59:01 UTC (1608479941)
[    3.198596] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    3.200310] vcc1v8_sys_s0: supplied by vcc1v8_sys_s3
[    3.200865] avdd_0v9_s0: supplied by vcc1v8_sys_s3
[    3.201397] vdd_cpu_b: supplied by vcc5v0_sys
[    3.204871] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    3.206609] vdd_gpu: supplied by vcc5v0_sys
[    3.216307] dw_wdt ff848000.watchdog: No valid TOPs array specified
[    3.219023] sdhci: Secure Digital Host Controller Interface driver
[    3.219583] sdhci: Copyright(c) Pierre Ossman
[    3.219997] Synopsys Designware Multimedia Card Interface Driver
[    3.222252] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
[    3.222910] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
[    3.223511] dwmmc_rockchip fe320000.mmc: Version ID is 270a
[    3.224064] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
[    3.225390] dwmmc_rockchip fe320000.mmc: Got CD GPIO
[    3.238788] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    3.250797] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.253109] mmc1: CQHCI version 5.10
[    3.278321] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    3.283378] ledtrig-cpu: registered to indicate activity on CPUs
[    3.285225] hid: raw HID events driver (C) Jiri Kosina
[    3.285918] usbcore: registered new interface driver usbhid
[    3.286063] random: fast init done
[    3.286425] usbhid: USB HID core driver
[    3.293058] drop_monitor: Initializing network drop monitor service
[    3.294508] NET: Registered protocol family 10
[    3.348187] mmc1: mmc_select_hs200 failed, error -110
[    3.348659] mmc1: error -110 whilst initialising MMC card
[    3.350747] Segment Routing with IPv6
[    3.351182] NET: Registered protocol family 17
[    3.351737] 8021q: 802.1Q VLAN Support v1.8
[    3.352166] Key type dns_resolver registered
[    3.353110] registered taskstats version 1
[    3.353491] Loading compiled-in X.509 certificates
[    3.357753] Loaded X.509 cert 'Build time autogenerated kernel key: cf582b85d37ac5e7e16062bd2222df75b99b261f'
[    3.358839] zswap: loaded using pool lzo/zbud
[    3.359592] Key type ._fscrypt registered
[    3.359958] Key type .fscrypt registered
[    3.360311] Key type fscrypt-provisioning registered
[    3.363898] Btrfs loaded, crc32c=crc32c-generic
[    3.391616] Key type encrypted registered
[    3.392045] AppArmor: AppArmor sha1 policy hashing enabled
[    3.450209] mmc1: mmc_select_hs200 failed, error -110
[    3.450688] mmc1: error -110 whilst initialising MMC card
[    3.452991] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges:
[    3.453701] rockchip-pcie f8000000.pcie:      MEM 0x00fa000000..0x00fbdfffff -> 0x00fa000000
[    3.454469] rockchip-pcie f8000000.pcie:       IO 0x00fbe00000..0x00fbefffff -> 0x00fbe00000
[    3.481707] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    3.510957] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
[    3.511556] pci_bus 0000:00: root bus resource [bus 00-1f]
[    3.512052] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff]
[    3.512675] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfbe00000-0xfbefffff])
[    3.513572] pci 0000:00:00.0: [1d87:0100] type 01 class 0x060400
[    3.514274] pci 0000:00:00.0: supports D1
[    3.514641] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    3.520653] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    3.521733] pci 0000:01:00.0: [197b:0585] type 00 class 0x010601
[    3.522337] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    3.522999] pci 0000:01:00.0: reg 0x10: [io  size 0x0080]
[    3.523534] pci 0000:01:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[    3.524164] pci 0000:01:00.0: reg 0x14: [io  size 0x0080]
[    3.524676] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[    3.525361] pci 0000:01:00.0: reg 0x18: [io  size 0x0080]
[    3.525888] pci 0000:01:00.0: reg 0x1c: initial BAR value 0x00000000 invalid
[    3.526517] pci 0000:01:00.0: reg 0x1c: [io  size 0x0080]
[    3.527057] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[    3.527705] pci 0000:01:00.0: reg 0x20: [io  size 0x0080]
[    3.528219] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x00001fff]
[    3.528807] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    3.529436] pci 0000:01:00.0: Max Payload Size set to 256 (was 128, max 512)
[    3.530393] pci 0000:01:00.0: PME# supported from D3hot
[    3.531103] pci 0000:01:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x2 link at 0000:00:00.0 (capable of 15.752 Gb/s with 8.0 GT/s PCIe x2 link)
[    3.537765] pci_bus 0000:01: busn_res: [bus 01-1f] end is updated to 01
[    3.538406] pci 0000:00:00.0: BAR 14: assigned [mem 0xfa000000-0xfa0fffff]
[    3.539031] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa00ffff pref]
[    3.539707] pci 0000:01:00.0: BAR 5: assigned [mem 0xfa010000-0xfa011fff]
[    3.540385] pci 0000:01:00.0: BAR 0: no space for [io  size 0x0080]
[    3.540948] pci 0000:01:00.0: BAR 0: failed to assign [io  size 0x0080]
[    3.541563] pci 0000:01:00.0: BAR 1: no space for [io  size 0x0080]
[    3.542174] pci 0000:01:00.0: BAR 1: failed to assign [io  size 0x0080]
[    3.542768] pci 0000:01:00.0: BAR 2: no space for [io  size 0x0080]
[    3.543328] pci 0000:01:00.0: BAR 2: failed to assign [io  size 0x0080]
[    3.543917] pci 0000:01:00.0: BAR 3: no space for [io  size 0x0080]
[    3.544477] pci 0000:01:00.0: BAR 3: failed to assign [io  size 0x0080]
[    3.545066] pci 0000:01:00.0: BAR 4: no space for [io  size 0x0080]
[    3.545625] pci 0000:01:00.0: BAR 4: failed to assign [io  size 0x0080]
[    3.546234] pci 0000:00:00.0: PCI bridge to [bus 01]
[    3.546688] pci 0000:00:00.0:   bridge window [mem 0xfa000000-0xfa0fffff]
[    3.547535] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    3.548391] pcieport 0000:00:00.0: PME: Signaling with IRQ 239
[    3.549233] pcieport 0000:00:00.0: AER: enabled with IRQ 239
[    3.550187] ahci 0000:01:00.0: version 3.0
[    3.550578] ahci 0000:01:00.0: enabling device (0000 -> 0002)
[    3.551645] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[    3.552331] ahci 0000:01:00.0: AHCI 0001.0301 32 slots 5 ports 6 Gbps 0x1f impl SATA mode
[    3.553065] ahci 0000:01:00.0: flags: 64bit ncq sntf stag pm led clo pmp fbs pio slum part ccc apst boh
[    3.559511] scsi host0: ahci
[    3.560510] scsi host1: ahci
[    3.561386] scsi host2: ahci
[    3.562292] scsi host3: ahci
[    3.563180] scsi host4: ahci
[    3.563724] ata1: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010100 irq 240
[    3.564429] ata2: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010180 irq 241
[    3.565125] ata3: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010200 irq 242
[    3.565838] ata4: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010280 irq 243
[    3.566532] ata5: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010300 irq 244
[    3.573576] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    3.577160] mmc1: mmc_select_hs200 failed, error -110
[    3.577624] mmc1: error -110 whilst initialising MMC card
[    3.577761] of_cfs_init
[    3.578449] of_cfs_init: OK
[    3.631765] usb 3-1: New USB device found, idVendor=2109, idProduct=2815, bcdDevice= 7.04
[    3.632503] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.633140] usb 3-1: Product: USB2.0 Hub
[    3.633594] usb 3-1: Manufacturer: VIA Labs, Inc.
[    3.685522] hub 3-1:1.0: USB hub found
[    3.686115] hub 3-1:1.0: 4 ports detected
[    3.739853] mmc1: Command Queue Engine enabled
[    3.740269] mmc1: new HS200 MMC card at address 0001
[    3.741441] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB
[    3.742111] mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB
[    3.742891] mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB
[    3.743579] mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB, chardev (243:0)
[    3.745394]  mmcblk1: p1
[    3.780208] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[    3.900257] usb 4-1: New USB device found, idVendor=2109, idProduct=0815, bcdDevice= 7.04
[    3.900994] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.901630] usb 4-1: Product: USB3.0 Hub
[    3.902109] usb 4-1: Manufacturer: VIA Labs, Inc.
[    3.925362] hub 4-1:1.0: USB hub found
[    3.925866] hub 4-1:1.0: 4 ports detected
[    4.041760] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    4.161931] ata1.00: ATA-8: TOSHIBA HDWQ140, FJ1M, max UDMA/100
[    4.162475] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    4.165321] ata1.00: configured for UDMA/100
[    4.166411] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA HDWQ140  FJ1M PQ: 0 ANSI: 5
[    4.168865] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    4.169644] sd 0:0:0:0: [sda] Write Protect is off
[    4.170134] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.170752] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.383857] sd 0:0:0:0: [sda] Attached SCSI disk
[    4.489693] usb 3-1.4: new high-speed USB device number 3 using xhci-hcd
[    4.645730] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    4.763879] ata2.00: ATA-8: TOSHIBA HDWQ140, FJ1M, max UDMA/100
[    4.764424] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    4.767274] ata2.00: configured for UDMA/100
[    4.768335] scsi 1:0:0:0: Direct-Access     ATA      TOSHIBA HDWQ140  FJ1M PQ: 0 ANSI: 5
[    4.770403] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    4.771174] sd 1:0:0:0: [sdb] Write Protect is off
[    4.771622] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    4.772194] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.982559] sd 1:0:0:0: [sdb] Attached SCSI disk
[    5.245708] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    5.301804] usb 4-1.4: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[    5.322919] usb 4-1.4: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[    5.323681] usb 4-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    5.324345] usb 4-1.4: Product: USB 10/100/1G/2.5G LAN
[    5.324815] usb 4-1.4: Manufacturer: Realtek
[    5.325210] usb 4-1.4: SerialNumber: 000000001
[    5.374117] ata3.00: ATA-8: TOSHIBA HDWQ140, FJ1M, max UDMA/100
[    5.374669] ata3.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    5.377521] ata3.00: configured for UDMA/100
[    5.378381] scsi 2:0:0:0: Direct-Access     ATA      TOSHIBA HDWQ140  FJ1M PQ: 0 ANSI: 5
[    5.380557] sd 2:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    5.381329] sd 2:0:0:0: [sdc] Write Protect is off
[    5.381804] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    5.382380] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.594324] sd 2:0:0:0: [sdc] Attached SCSI disk
[    5.692297] ata4: SATA link down (SStatus 0 SControl 300)
[    6.169715] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    6.172193] ata5.00: ATA-9: SanDisk SSD PLUS 120GB, UE4500RL, max UDMA/133
[    6.172820] ata5.00: 234455040 sectors, multi 1: LBA48 NCQ (depth 32)
[    6.178793] ata5.00: configured for UDMA/133
[    6.179784] scsi 4:0:0:0: Direct-Access     ATA      SanDisk SSD PLUS 00RL PQ: 0 ANSI: 5
[    6.182116] sd 4:0:0:0: [sdd] 234455040 512-byte logical blocks: (120 GB/112 GiB)
[    6.182886] sd 4:0:0:0: [sdd] Write Protect is off
[    6.183336] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[    6.183927] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.189270] sd 4:0:0:0: [sdd] Attached SCSI disk
[    6.192627] Freeing unused kernel memory: 4224K
[    6.205802] Run /init as init process
[    6.206145]   with arguments:
[    6.206421]     /init
[    6.206636]   with environment:
[    6.206927]     HOME=/
[    6.207149]     TERM=linux
[    6.207402]     ubootpart=92c32d3c-01
[    6.207738]     cgroup_enable=memory
[    6.208066]     cgroup_memory=1
[    7.124689] input: adc-keys as /devices/platform/adc-keys/input/input1
[    7.216691] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
[    7.217379] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
[    7.218154] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[    7.218943] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    7.219581] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    7.220092] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
[    7.220607] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    7.221229] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    7.223029] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    7.228611] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    7.229458] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[    7.230238] rk_gmac-dwmac fe300000.ethernet:         DWMAC1000
[    7.230775] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
[    7.231464] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
[    7.232147] rk_gmac-dwmac fe300000.ethernet: COE Type 2
[    7.232629] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
[    7.233271] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[    7.234026] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[    7.234580] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[    7.235102] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    7.372074] libphy: stmmac: probed
[    7.372431] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    7.373562] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[    7.383559] async_tx: api initialized (async)
[    7.412959] md/raid:md0: device sda operational as raid disk 0
[    7.413515] md/raid:md0: device sdc operational as raid disk 2
[    7.414092] md/raid:md0: device sdb operational as raid disk 1
[    7.418768] md/raid:md0: raid level 5 active with 3 out of 3 devices, algorithm 2
[    7.581793] md0: detected capacity change from 0 to 8001302822912
[    8.234906] EXT4-fs (mmcblk1p1): mounted filesystem with writeback data mode. Opts: (null)
[    8.713233] systemd[1]: Inserted module 'autofs4'
[    8.741159] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    8.743991] systemd[1]: Detected architecture arm64.
[    8.776084] systemd[1]: Set hostname to <datadevil4>.
[    8.892101] dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
[    8.958048] random: lvmconfig: uninitialized urandom read (4 bytes read)
[    9.234036] systemd[1]: /lib/systemd/system/smbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/smbd.pid → /run/samba/smbd.pid; please update the unit file accordingly.
[    9.250353] systemd[1]: /lib/systemd/system/nmbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/nmbd.pid → /run/samba/nmbd.pid; please update the unit file accordingly.
[    9.274131] systemd[1]: /lib/systemd/system/fancontrol.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/fancontrol.pid → /run/fancontrol.pid; please update the unit file accordingly.
[    9.305592] systemd[1]: /lib/systemd/system/rpc-statd.service:13: PIDFile= references path below legacy directory /var/run/, updating /var/run/rpc.statd.pid → /run/rpc.statd.pid; please update the unit file accordingly.
[    9.380061] random: systemd: uninitialized urandom read (16 bytes read)
[    9.391644] random: systemd: uninitialized urandom read (16 bytes read)
[    9.393029] systemd[1]: Listening on LVM2 poll daemon socket.
[    9.394417] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    9.395922] systemd[1]: Listening on Syslog Socket.
[    9.514348] lm75 2-004c: hwmon2: sensor 'lm75'
[    9.559853] RPC: Registered named UNIX socket transport module.
[    9.560420] RPC: Registered udp transport module.
[    9.560860] RPC: Registered tcp transport module.
[    9.561298] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.569951] EXT4-fs (mmcblk1p1): re-mounted. Opts: commit=600,errors=remount-ro
[    9.638294] random: crng init done
[    9.638621] random: 7 urandom warning(s) missed due to ratelimiting
[    9.729095] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    9.749971] device-mapper: uevent: version 1.0.3
[    9.750918] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com
[   10.090231] systemd-journald[443]: Received request to flush runtime journal from PID 1
[   10.180460] rk_gmac-dwmac fe300000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=POLL)
[   10.201741] rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found
[   10.202447] rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW
[   10.214336] rk_gmac-dwmac fe300000.ethernet eth0: configuring for phy/rgmii link mode
[   10.583176] input: beeper as /devices/platform/beeper/input/input2
[   10.744803] rockchip-vop ff8f0000.vop: Adding to iommu group 2
[   10.795257] rockchip-vop ff900000.vop: Adding to iommu group 3
[   10.823658] mc: Linux media interface: v0.10
[   10.907076] videodev: Linux video capture interface: v2.00
[   10.954611] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   10.955347] sd 1:0:0:0: Attached scsi generic sg1 type 0
[   10.956000] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   10.956666] sd 4:0:0:0: Attached scsi generic sg3 type 0
[   10.989568] OF: graph: no port node found in /i2c@ff3d0000/typec-portc@22
[   11.012713] rockchip_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[   11.016543] rkvdec ff660000.video-codec: Adding to iommu group 1
[   11.016851] hantro_vpu: module is from the staging directory, the quality is unknown, you have been warned.
[   11.019603] hantro-vpu ff650000.video-codec: Adding to iommu group 0
[   11.024269] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-enc as /dev/video0
[   11.025246] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-dec as /dev/video1
[   11.030132] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops [rockchipdrm])
[   11.031048] [drm] unsupported AFBC format[3231564e]
[   11.033165] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops [rockchipdrm])
[   11.034488] rockchip-drm display-subsystem: bound fec00000.dp (ops cdn_dp_component_ops [rockchipdrm])
[   11.037166] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[   11.050873] rockchip-rga ff680000.rga: HW Version: 0x03.02
[   11.053401] rockchip-rga ff680000.rga: Registered rockchip-rga as /dev/video3
[   11.089845] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[   11.091020] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
[   11.097327] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/otg-port
[   11.102475] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[   11.102985] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 5
[   11.103800] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[   11.104646] xhci-hcd xhci-hcd.3.auto: irq 227, io mem 0xfe800000
[   11.105410] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.09
[   11.106163] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.106798] usb usb5: Product: xHCI Host Controller
[   11.107228] usb usb5: Manufacturer: Linux 5.9.11-rockchip64 xhci-hcd
[   11.107784] usb usb5: SerialNumber: xhci-hcd.3.auto
[   11.108557] hub 5-0:1.0: USB hub found
[   11.108923] hub 5-0:1.0: 1 port detected
[   11.109462] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[   11.110141] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 6
[   11.110831] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[   11.111462] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[   11.112242] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.09
[   11.112968] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.113601] usb usb6: Product: xHCI Host Controller
[   11.114055] usb usb6: Manufacturer: Linux 5.9.11-rockchip64 xhci-hcd
[   11.114615] usb usb6: SerialNumber: xhci-hcd.3.auto
[   11.115386] hub 6-0:1.0: USB hub found
[   11.115749] hub 6-0:1.0: 1 port detected
[   11.276433] panfrost ff9a0000.gpu: clock rate = 500000000
[   11.278555] panfrost ff9a0000.gpu: mali-t860 id 0x860 major 0x2 minor 0x0 status 0x0
[   11.279278] panfrost ff9a0000.gpu: features: 00000000,100e77bf, issues: 00000000,24040400
[   11.280011] panfrost ff9a0000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7
[   11.281057] panfrost ff9a0000.gpu: shader_present=0xf l2_present=0x1
[   11.347408] [drm] Initialized panfrost 1.1.0 20180908 for ff9a0000.gpu on minor 1
[   11.367604] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[   11.621209] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[   11.781636] usb 4-1.4: reset SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[   11.914059] r8152 4-1.4:1.0 (unnamed net_device) (uninitialized): netif_napi_add() called with weight 256
[   11.933839] r8152 4-1.4:1.0 eth1: v2.13.0 (2020/04/20)
[   11.934307] r8152 4-1.4:1.0 eth1: This product is covered by one or more of the following patents:
[   11.934307]          US6,570,884, US6,115,776, and US6,327,625.
[   11.934307]
[   11.935821] usbcore: registered new interface driver r8152
[   12.546016] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[   13.282537] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   13.283343] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   13.391749] NFSD: Using UMH upcall client tracking operations.
[   13.392294] NFSD: starting 90-second grace period (net f00000a1)
[   33.759159] vcc3v0_sd: disabling
[   33.759458] vcc5v0_typec: disabling
[  100.073800] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
[  100.074564] softdog:              soft_reboot_cmd=<not set> soft_active_on_boot=0

 

Edited by Werner
Add spoiler
Link to comment
Share on other sites

@mortomanos looks like something wrong with the eMMC. It works intermittently.

on your first log, there are several error like this

[    3.351947] mmc1: mmc_select_hs200 failed, error -110
[    3.352420] mmc1: error -110 whilst initialising MMC card

 

On your second log, it failed for several times but finally it initialized

[    3.577160] mmc1: mmc_select_hs200 failed, error -110
[    3.577624] mmc1: error -110 whilst initialising MMC card
[    3.577761] of_cfs_init
[    3.578449] of_cfs_init: OK
[    3.631765] usb 3-1: New USB device found, idVendor=2109, idProduct=2815, bcdDevice= 7.04
[    3.632503] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.633140] usb 3-1: Product: USB2.0 Hub
[    3.633594] usb 3-1: Manufacturer: VIA Labs, Inc.
[    3.685522] hub 3-1:1.0: USB hub found
[    3.686115] hub 3-1:1.0: 4 ports detected
[    3.739853] mmc1: Command Queue Engine enabled
[    3.740269] mmc1: new HS200 MMC card at address 0001
[    3.741441] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB
[    3.742111] mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB
[    3.742891] mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB
[    3.743579] mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB, chardev (243:0)
[    3.745394]  mmcblk1: p1

 

Could you check whether you have P10 jumper enabled?

Link to comment
Share on other sites

Am 21.12.2020 um 08:39 schrieb aprayoga:

Could you check whether you have P10 jumper enabled?

 

No, both P10 and P11 are not shortened.

 

After upgrade to kernel 5.9.14 I haven't experienced the same problem so far, but this were only a handful of reboots. Also the initialization errors were not in the kernel logs so far. I will post an update if it happens again.

Link to comment
Share on other sites

Am 22.12.2020 um 13:42 schrieb mortomanos:

After upgrade to kernel 5.9.14 I haven't experienced the same problem so far, but this were only a handful of reboots. Also the initialization errors were not in the kernel logs so far. I will post an update if it happens again.

 

Unfortunately today I had several reboots with the same problem again. MMC did not initialize, always with the same error -110. What can be the problem then?

Link to comment
Share on other sites

I have armbian focal installed in mmc, kernel 5.10.16-rockchip64.

After `reboot` command, boot never completes (no heatbeat LED, no network access), though boot process seem to go quite far:

[   10.832087] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
[   10.832732] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[   10.833507] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[   10.834059] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[   10.834594] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[   10.843920] rockchip-vop ff8f0000.vop: Adding to iommu group 2
[   10.847541] rockchip-vop ff900000.vop: Adding to iommu group 3
[   10.973820] libphy: stmmac: probed
[   10.974169] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[   10.975287] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[   11.294450] async_tx: api initialized (async)
[   11.450714] BTRFS: device label export devid 3 transid 224560 /dev/sdb1 scanned by btrfs (353)
[   11.452467] BTRFS: device label export devid 2 transid 224560 /dev/sda1 scanned by btrfs (353)
[   33.760041] vcc3v0_sd: disabling
[   33.760359] vcc5v0_typec: disabling
[   42.900266] random: crng init done

After reset button, boot sometimes completes, sometimes not. After power cycle, boot always completes.

Should I, too, contact support?

And what is "armbian overlay"?

 

Link to comment
Share on other sites

To give some feedback after more than one month of operation: The reboot problem did not happen again after using the overlay. For me, the problem is solved as for now.

I recommend every user with similar problems, just post your serial output in new threads in the forum, and contact support if the board admins advise it. Great support from Kobol, thank you.

Link to comment
Share on other sites

seeing a similar issue

 

Helios was already working for some time, aside from regular crashes, but doesnt boot up anymore.

 

It does boot but crashes within a few seconds.

 

Any idea?

 

to rule out unrelated software issues, i flashed the current Armbian_21.02.3_Helios64_buster_current_5.10.21 image on a sd card.

 

Helios doesnt boot form the existing OS on the nand, nor from the fresh one on the sd.

 

 

 

Spoiler

DDR Version 1.24 20191016
Inotdev=UUID=c559a861-be25-4b41-a161-d0c3d75c0089
channel 0e=ext4
CS = 0ragequirks=0x2537:0x1066:u,0x2537:0x1068:u
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1                      [ Wrote 9 lines ]
CS = 0 Help  ^O Write Out ^W Where Is  ^K Cut Text  ^J Justify   ^C Cur Pos
MR0=0x18     ^R Read File ^\ Replace   ^U Uncut Text^T To Spell  ^_ Go To Line
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
256B stride
channel 0
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
change freq to 856MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x40
ch 1 ddrconfig = 0x101, ddrsize = 0x40
pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD
ddr_set_rate to 328MHZ
ddr_set_rate to 666MHZ
ddr_set_rate to 928MHZ
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
ddr_set_rate to 416MHZ, ctl_index 0
ddr_set_rate to 856MHZ, ctl_index 1
support 416 856 328 666 928 MHz, current 856MHz
OUT
Boot1: 2019-03-14, version: 1.19
CPUId = 0x0
ChipType = 0x10, 254
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=14910MB
FwPartOffset=2000 , 100000
mmc0:cmd5,20
SdmmcInit=0 0
BootCapSize=0
UserCapSize=61056MB
FwPartOffset=2000 , 0
StorageInit ok = 65442
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT 0x3380ec0 signature is wrong
recovery gpt...
GPT 0x3380ec0 signature is wrong
recovery gpt fail!
LoadTrust Addr:0x4000
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xe5b60
RunBL31 0x40000
NOTICE:  BL31: v1.3(debug):42583b6
NOTICE:  BL31: Built : 07:55:13, Oct 15 2019
NOTICE:  BL31: Rockchip release version: v1.1
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    plat_rockchip_pmu_init(1190): pd status 3e
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2020.10-armbian (Mar 08 2021 - 14:54:58 +0000)

SoC: Rockchip rk3399
Reset cause: POR
DRAM:  3.9 GiB
PMIC:  RK808
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
MMC:   mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Helios64
Revision: 1.2 - 4GB non ECC
Net:   eth0: ethernet@fe300000
scanning bus for devices...
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 4!?
5 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
3185 bytes read in 5 ms (622.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 1
220 bytes read in 4 ms (53.7 KiB/s)
13851809 bytes read in 598 ms (22.1 MiB/s)
28582400 bytes read in 1214 ms (22.5 MiB/s)
81913 bytes read in 13 ms (6 MiB/s)
2698 bytes read in 7 ms (376 KiB/s)
Applying kernel provided DT fixup script (rockchip-fixup.scr)
## Executing script at 09000000
Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    13851745 Bytes = 13.2 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f51b9000, end f5eeec61 ... OK
   Loading Device Tree to 00000000f513c000, end 00000000f51b8fff ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.10.21-rockchip64 (root@hirsute) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the                                         A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #21.02.3 SMP PREEMPT Mon Mar 8 01:05:08 UTC 2021
[    0.000000] Machine model: Helios64
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 128 MiB at 0x00000000ed000000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xf77d9100-0xf77dafff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000200000-0x000000003fffffff]
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000f7ffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
[    0.000000] On node 0 totalpages: 1015296
[    0.000000]   DMA zone: 4088 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 261632 pages, LIFO batch:63
[    0.000000]   DMA32 zone: 11776 pages used for memmap
[    0.000000]   DMA32 zone: 753664 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 32 pages/cpu s94040 r8192 d28840 u131072
[    0.000000] pcpu-alloc: s94040 r8192 d28840 u131072 alloc=32*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 999432
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: root=UUID=c559a861-be25-4b41-a161-d0c3d75c0089 rootwait rootfstype=ext4 console=ttyS2,1500000  consoleblank=0 loglevel=7 ubootpart=559a8d18-01 usb-storage.quirks                                        =0x2537:0x1066:u,0x2537:0x1068:u earlyprintk ignore_loglevel  cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x000000003bfff000-0x000000003ffff000] (64MB)
[    0.000000] Memory: 3741224K/4061184K available (14848K kernel code, 2632K rwdata, 5972K rodata, 4352K init, 580K bss, 188888K reserved, 131072K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[    0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @40100000 (flat, esz 8, psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GICv3: using LPI property table @0x00000000400d0000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000000400e0000
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] random: get_random_bytes called from start_kernel+0x698/0x850 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001521] Console: colour dummy device 80x25
[    0.001666] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.001691] pid_max: default: 32768 minimum: 301
[    0.001861] LSM: Security Framework initializing
[    0.001907] Yama: becoming mindful.
[    0.002059] AppArmor: AppArmor initialized
[    0.002167] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.002203] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.005920] rcu: Hierarchical SRCU implementation.
[    0.007117] Platform MSI: interrupt-controller@fee20000 domain created
[    0.007762] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.010300] EFI services will not be available.
[    0.011024] smp: Bringing up secondary CPUs ...
[    0.012208] Detected VIPT I-cache on CPU1
[    0.012258] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.012278] GICv3: CPU1: using allocated LPI pending table @0x00000000400f0000
[    0.012356] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.013783] Detected VIPT I-cache on CPU2
[    0.013831] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.013851] GICv3: CPU2: using allocated LPI pending table @0x0000000040180000
[    0.013929] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.015386] Detected VIPT I-cache on CPU3
[    0.015436] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.015456] GICv3: CPU3: using allocated LPI pending table @0x0000000040190000
[    0.015532] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.016959] CPU features: detected: Spectre-v2
[    0.016967] CPU features: detected: Spectre-v4
[    0.016972] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.016980] Detected PIPT I-cache on CPU4
[    0.017016] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.017031] GICv3: CPU4: using allocated LPI pending table @0x00000000401a0000
[    0.017080] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[    0.018348] Detected PIPT I-cache on CPU5
[    0.018387] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.018402] GICv3: CPU5: using allocated LPI pending table @0x00000000401b0000
[    0.018451] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[    0.018635] smp: Brought up 1 node, 6 CPUs
[    0.018746] SMP: Total of 6 processors activated.
[    0.018762] CPU features: detected: 32-bit EL0 Support
[    0.018776] CPU features: detected: CRC32 instructions
[    0.018791] CPU features: detected: 32-bit EL1 Support
[    0.045622] CPU: All CPU(s) started at EL2
[    0.045704] alternatives: patching kernel code
[    0.049491] devtmpfs: initialized
[    0.066199] Registered cp15_barrier emulation handler
[    0.066229] Registered setend emulation handler
[    0.066471] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.066549] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.069578] pinctrl core: initialized pinctrl subsystem
[    0.070259] D
                [    2.821492] hub 2-0:1.0: USB hub found
[    2.821889] hub 2-0:1.0: 1 port detected
[    2.823885] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.824391] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3
[    2.825227] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000010002010010
[    2.826141] xhci-hcd xhci-hcd.0.auto: irq 76, io mem 0xfe900000
[    2.827088] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.827818] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.828455] usb usb3: Product: xHCI Host Controller
[    2.828889] usb usb3: Manufacturer: Linux 5.10.21-rockchip64 xhci-hcd
[    2.829459] usb usb3: SerialNumber: xhci-hcd.0.auto
[    2.830478] hub 3-0:1.0: USB hub found
[    2.830849] hub 3-0:1.0: 1 port detected
[    2.831551] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.832049] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4
[    2.832732] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    2.833385] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.834259] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[    2.834988] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.835625] usb usb4: Product: xHCI Host Controller
[    2.836059] usb usb4: Manufacturer: Linux 5.10.21-rockchip64 xhci-hcd
[    2.836628] usb usb4: SerialNumber: xhci-hcd.0.auto
[    2.837552] hub 4-0:1.0: USB hub found
[    2.837968] hub 4-0:1.0: 1 port detected
[    2.838809] usbcore: registered new interface driver usb-storage
[    2.842164] mousedev: PS/2 mouse device common for all mice
[    2.844166] i2c /dev entries driver
[    2.848644] pca953x 2-0020: using no AI
[    2.859307] rk808 0-001b: chip id: 0x0
[    2.863972] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    2.864545] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    2.865095] rk808-regulator rk808-regulator: max buck steps per change: 4
[    2.866819] vdd_center: supplied by vcc5v0_sys
[    2.867891] vdd_cpu_l: supplied by vcc5v0_sys
[    2.868661] vcc_ddr_s3: supplied by vcc5v0_sys
[    2.869715] vcc1v8_sys_s3: supplied by vcc5v0_sys
[    2.870801] vcc1v8_dvp: supplied by vcc5v0_sys
[    2.871711] vcc3v0_touch: supplied by vcc5v0_sys
[    2.873452] vcc1v8_s3: supplied by vcc5v0_sys
[    2.874154] vcc_sdio_s0: Bringing 3300000uV into 3000000-3000000uV
[    2.875859] vcc_sdio_s0: supplied by vcc5v0_sys
[    2.876788] vcca3v0_codec: supplied by vcc5v0_sys
[    2.878407] vcc1v5_s3: supplied by vcc5v0_sys
[    2.879312] vcca1v8_codec: supplied by vcc5v0_sys
[    2.880941] vcc3v0_s3: supplied by vcc5v0_sys
[    2.881465] vcc3v3_sys_s0: failed to get the current voltage: -EPROBE_DEFER
[    2.882119] vcc3v3_sys_s0: supplied by vcc3v3_sys_s3
[    2.883132] vcc3v3_s0: supplied by vcc3v3_sys_s3
[    2.887209] rk808-rtc rk808-rtc: registered as rtc0
[    2.888208] rk808-rtc rk808-rtc: setting system clock to 2021-03-16T10:38:47 UTC (1615891127)
[    2.892106] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    2.894095] vcc1v8_sys_s0: supplied by vcc1v8_sys_s3
[    2.894627] avdd_0v9_s0: supplied by vcc1v8_sys_s3
[    2.895163] vdd_cpu_b: supplied by vcc5v0_sys
[    2.898615] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    2.899645] random: fast init done
[    2.901008] vdd_gpu: supplied by vcc5v0_sys
[    2.909085] dw_wdt ff848000.watchdog: No valid TOPs array specified
[    2.911740] sdhci: Secure Digital Host Controller Interface driver
[    2.912289] sdhci: Copyright(c) Pierre Ossman
[    2.912698] Synopsys Designware Multimedia Card Interface Driver
[    2.914642] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.915048] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
[    2.929311] drop_monitor: Initializing network drop monitor service
[    2.930740] NET: Registered protocol family 10
[    2.931708] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.945243] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    2.988069] Segment Routing with IPv6
[    2.988499] NET: Registered protocol family 17
[    2.989048] 8021q: 802.1Q VLAN Support v1.8
[    2.989479] Key type dns_resolver registered
[    2.990446] registered taskstats version 1
[    2.990822] Loading compiled-in X.509 certificates
[    2.994954] Loaded X.509 cert 'Build time autogenerated kernel key: 98b5fbd0004968eadd44123544af94c22f57c8e4'
[    2.997820] mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[    3.000145] dwmmc_rockchip fe320000.mmc: All phases bad!
[    3.000629] mmc1: tuning execution failed: -5
[    3.001030] mmc1: error -5 whilst initialising SD card
[    3.002533] zswap: loaded using pool zstd/z3fold
[    3.003345] Key type ._fscrypt registered
[    3.003706] Key type .fscrypt registered
[    3.004058] Key type fscrypt-provisioning registered
[    3.007798] Btrfs loaded, crc32c=crc32c-generic
[    3.015413] mmc2: Command Queue Engine enabled
[    3.015827] mmc2: new HS400 Enhanced strobe MMC card at address 0001
[    3.017116] mmcblk2: mmc2:0001 AJTD4R 14.6 GiB
[    3.017756] mmcblk2boot0: mmc2:0001 AJTD4R partition 1 4.00 MiB
[    3.018567] mmcblk2boot1: mmc2:0001 AJTD4R partition 2 4.00 MiB
[    3.019265] mmcblk2rpmb: mmc2:0001 AJTD4R partition 3 4.00 MiB, chardev (243:0)
[    3.020891]  mmcblk2: p1 p2
[    3.025991] mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[    3.035918] Key type encrypted registered
[    3.036304] AppArmor: AppArmor sha1 policy hashing enabled
[    3.087925] mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[    3.088065] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges:
[    3.089456] rockchip-pcie f8000000.pcie:      MEM 0x00fa000000..0x00fbdfffff -> 0x00fa000000
[    3.090261] rockchip-pcie f8000000.pcie:       IO 0x00fbe00000..0x00fbefffff -> 0x00fbe00000
[    3.147162] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
[    3.147755] pci_bus 0000:00: root bus resource [bus 00-1f]
[    3.148244] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff]
[    3.148856] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfbe00000-0xfbefffff])
[    3.149744] pci 0000:00:00.0: [1d87:0100] type 01 class 0x060400
[    3.150449] pci 0000:00:00.0: supports D1
[    3.150810] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    3.157179] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    3.158149] pci 0000:01:00.0: [197b:0585] type 00 class 0x010601
[    3.158743] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    3.159366] pci 0000:01:00.0: reg 0x10: [io  size 0x0080]
[    3.159873] pci 0000:01:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[    3.160495] pci 0000:01:00.0: reg 0x14: [io  size 0x0080]
[    3.161001] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[    3.161622] pci 0000:01:00.0: reg 0x18: [io  size 0x0080]
[    3.162147] pci 0000:01:00.0: reg 0x1c: initial BAR value 0x00000000 invalid
[    3.162770] pci 0000:01:00.0: reg 0x1c: [io  size 0x0080]
[    3.163276] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[    3.163898] pci 0000:01:00.0: reg 0x20: [io  size 0x0080]
[    3.164406] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x00001fff]
[    3.164989] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    3.165612] pci 0000:01:00.0: Max Payload Size set to 256 (was 128, max 512)
[    3.166594] pci 0000:01:00.0: PME# supported from D3hot
[    3.167299] pci 0000:01:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x2 link at 0000:00:00.0 (capable of 15.752 Gb/s with 8.0 GT/s PCIe x2 link)
[    3.174157] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[    3.174966] pci_bus 0000:01: busn_res: [bus 01-1f] end is updated to 01
[    3.175574] pci 0000:00:00.0: BAR 14: assigned [mem 0xfa000000-0xfa0fffff]
[    3.176190] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa00ffff pref]
[    3.176831] pci 0000:01:00.0: BAR 5: assigned [mem 0xfa010000-0xfa011fff]
[    3.177443] pci 0000:01:00.0: BAR 0: no space for [io  size 0x0080]
[    3.178015] pci 0000:01:00.0: BAR 0: failed to assign [io  size 0x0080]
[    3.178600] pci 0000:01:00.0: BAR 1: no space for [io  size 0x0080]
[    3.179156] pci 0000:01:00.0: BAR 1: failed to assign [io  size 0x0080]
[    3.179741] pci 0000:01:00.0: BAR 2: no space for [io  size 0x0080]
[    3.180295] pci 0000:01:00.0: BAR 2: failed to assign [io  size 0x0080]
[    3.180880] pci 0000:01:00.0: BAR 3: no space for [io  size 0x0080]
[    3.181435] pci 0000:01:00.0: BAR 3: failed to assign [io  size 0x0080]
[    3.182037] pci 0000:01:00.0: BAR 4: no space for [io  size 0x0080]
[    3.182591] pci 0000:01:00.0: BAR 4: failed to assign [io  size 0x0080]
[    3.183179] pci 0000:00:00.0: PCI bridge to [bus 01]
[    3.183627] pci 0000:00:00.0:   bridge window [mem 0xfa000000-0xfa0fffff]
[    3.184462] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    3.185317] pcieport 0000:00:00.0: PME: Signaling with IRQ 90
[    3.186186] pcieport 0000:00:00.0: AER: enabled with IRQ 90
[    3.187032] ahci 0000:01:00.0: version 3.0
[    3.187418] ahci 0000:01:00.0: enabling device (0000 -> 0002)
[    3.188535] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[    3.189214] ahci 0000:01:00.0: AHCI 0001.0301 32 slots 5 ports 6 Gbps 0x1f impl SATA mode
[    3.189967] ahci 0000:01:00.0: flags: 64bit ncq sntf stag pm led clo pmp fbs pio slum part ccc apst boh
[    3.194412] scsi host0: ahci
[    3.195390] scsi host1: ahci
[    3.196284] scsi host2: ahci
[    3.197168] scsi host3: ahci
[    3.198088] scsi host4: ahci
[    3.198575] ata1: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010100 irq 91
[    3.199233] ata2: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010180 irq 92
[    3.199887] ata3: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010200 irq 93
[    3.200539] ata4: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010280 irq 94
[    3.201191] ata5: SATA max UDMA/133 abar m8192@0xfa010000 port 0xfa010300 irq 95
[    3.210157] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    3.211343] of_cfs_init
[    3.211600] of_cfs_init: OK
[    3.213268] dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
[    3.516447] ata1: SATA link down (SStatus 0 SControl 300)
[    3.702502] mmc_host mmc1: Timeout sending command (cmd 0x200000 arg 0x0 status 0x80200000)
[    4.203306] dwmmc_rockchip fe320000.mmc: Busy; trying anyway
[    4.205379] usb 4-1: New USB device found, idVendor=2109, idProduct=0815, bcdDevice= 7.04
[    4.206123] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.206754] usb 4-1: Product: USB3.0 Hub
[    4.207203] usb 4-1: Manufacturer: VIA Labs, Inc.
[    4.225676] hub 4-1:1.0: USB hub found
[    4.226146] hub 4-1:1.0: 4 ports detected
[    4.310292] ata2: SATA link down (SStatus 0 SControl 300)
[    4.329903] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    4.853897] mmc_host mmc1: Timeout sending command (cmd 0x200000 arg 0x0 status 0x80200000)
[    5.354700] dwmmc_rockchip fe320000.mmc: Busy; trying anyway
[    5.356530] usb 3-1: New USB device found, idVendor=2109, idProduct=2815, bcdDevice= 7.04
[    5.357256] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.357915] usb 3-1: Product: USB2.0 Hub
[    5.358366] usb 3-1: Manufacturer: VIA Labs, Inc.
[    5.393675] hub 3-1:1.0: USB hub found
[    5.394279] hub 3-1:1.0: 4 ports detected
[    5.461915] ata3: SATA link down (SStatus 0 SControl 300)
[    5.638015] dwmmc_rockchip fe320000.mmc: Successfully tuned phase to 289
[    5.638628] mmc1: new ultra high speed SDR104 SDXC card at address 0001
[    5.640431] mmcblk1: mmc1:0001 EC2QT 59.6 GiB
[    5.641993] usb 4-1.4: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[    5.643365]  mmcblk1: p1
[    5.663020] usb 4-1.4: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[    5.663761] usb 4-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    5.664405] usb 4-1.4: Product: USB 10/100/1G/2.5G LAN
[    5.664862] usb 4-1.4: Manufacturer: Realtek
[    5.665244] usb 4-1.4: SerialNumber: 000000001
[    5.776495] ata4: SATA link down (SStatus 0 SControl 300)
[    6.092566] ata5: SATA link down (SStatus 0 SControl 300)
[    6.096094] Freeing unused kernel memory: 4352K
[    6.096673] Run /init as init process
[    6.097007]   with arguments:
[    6.097277]     /init
[    6.097487]     earlyprintk
[    6.097742]   with environment:
[    6.098077]     HOME=/
[    6.098296]     TERM=linux
[    6.098545]     ubootpart=559a8d18-01
[    6.098876]     cgroup_enable=memory
[    6.099198]     cgroup_memory=1
Loading, please wait...
Starting version 241
[    6.189892] usb 3-1.1: new full-speed USB device number 3 using xhci-hcd
[    6.340122] usb 3-1.1: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[    6.340869] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    6.341516] usb 3-1.1: Product: ConBee II
[    6.341904] usb 3-1.1: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[    6.342535] usb 3-1.1: SerialNumber: DE2140506
[    6.699923] input: adc-keys as /devices/platform/adc-keys/input/input1
[    6.765078] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
[    6.765674] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
[    6.766527] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[    6.779987] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    6.780624] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    6.782775] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
[    6.783315] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    6.785504] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    6.786327] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    6.792722] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    6.801068] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[    6.801953] rk_gmac-dwmac fe300000.ethernet:         DWMAC1000
[    6.802449] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
[    6.803115] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
[    6.803779] rk_gmac-dwmac fe300000.ethernet: COE Type 2
[    6.804248] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
[    6.804874] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[    6.805602] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[    6.806395] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[    6.806928] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    6.947744] libphy: stmmac: probed
[    6.948096] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    6.949215] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
Begin: Loading essential drivers ... [    7.169416] async_tx: api initialized (async)
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext4 (1) -- /dev/mmcblk1p1] fsck.ext4 -a -C0 /dev/mmcblk1p1
/dev/mmcblk1p1: clean, 45497/4434848 files, 686832/15469936 blocks
done.
[    7.622080] EXT4-fs (mmcblk1p1): mounted filesystem with writeback data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... /scripts/local-bottom/mdadm: 2: /scripts/local-bottom/mdadm: rm: not found
done.
Begin: Running /scripts/init-bottom ... done.
[    8.277904] systemd[1]: Inserted module 'autofs4'
[    8.330973] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KM                                        OD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    8.333823] systemd[1]: Detected architecture arm64.

Welcome to Armbian 21.02.3 Buster!

[    8.363191] systemd[1]: Set hostname to <helios64>.
[    8.735827] systemd[1]: /lib/systemd/system/fancontrol.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/fancontrol.pid → /run/fancontrol.pid; please update                                         the unit file accordingly.
[    8.812113] random: systemd: uninitialized urandom read (16 bytes read)
[    8.820875] random: systemd: uninitialized urandom read (16 bytes read)
[    8.825723] systemd[1]: Created slice system-getty.slice.
[  OK  ] Created slice system-getty.slice.
[    8.827366] random: systemd: uninitialized urandom read (16 bytes read)
[    8.828724] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    8.842577] systemd[1]: Starting Set the console keyboard layout...
         Starting Set the console keyboard layout...
[    8.844472] systemd[1]: Listening on initctl Compatibility Named Pipe.
[  OK  ] Listening on initctl Compatibility Named Pipe.
[    8.858196] systemd[1]: Starting Nameserver information manager...
         Starting Nameserver information manager...
[    8.865372] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[  OK  ] Set up automount Arbitrary…s File System Automount Point.
[  OK  ] Reached target Swap.
[  OK  ] Reached target Remote File Systems.
         Starting Create list of re…odes for the current kernel...
[  OK  ] Listening on fsck to fsckd communication Socket.
[  OK  ] Reached target Local Encrypted Volumes.
[  OK  ] Listening on udev Control Socket.
         Starting Remount Root and Kernel File Systems...
[  OK  ] Reached target System Time Synchronized.
         Mounting Kernel Debug File System...
[  OK  ] Listening on Journal Audit Socket.
         Mounting Huge Pages File System...
[  OK  ] Reached target Paths.
[  OK  ] Listening on Journal Socket (/dev/log).
[    9.060804] EXT4-fs (mmcblk1p1): re-mounted. Opts: commit=600,errors=remount-ro
[  OK  ] Listening on udev Kernel Socket.
         Starting udev Coldplug all Devices...
[  OK  ] Listening on Syslog Socket.
         Starting Load Kernel Modules...
[  OK  ] Created slice User and Session Slice.
[  OK  ] Reached target Slices.
[  OK  ] Mounted POSIX Message Queue File System.
[    9.171606] lm75 2-004c: supply vs not found, using dummy regulator
[    9.173306] lm75 2-004c: hwmon2: sensor 'lm75'
[  OK  ] Started Create list of req… nodes for the current kernel.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Mounted Kernel Debug File System.
[  OK  ] Mounted Huge Pages File System.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Set the console keyboard layout.
[  OK  ] Started Nameserver information manager.
         Starting Apply Kernel Variables...
         Mounting Kernel Configuration File System...
         Mounting FUSE Control File System...
         Starting Load/Save Random Seed...
         Starting Create System Users...
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Mounted FUSE Control File System.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Create System Users.
         Starting Create Static Device Nodes in /dev...
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /tmp...
         Starting udev Kernel Device Manager...
[  OK  ] Mounted /tmp.
[  OK  ] Reached target Local File Systems.
         Starting Armbian ZRAM config...
         Starting Set console font and keymap...
[  OK  ] Started Set console font and keymap.
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started udev Coldplug all Devices.
         Starting Helper to synchronize boot up for ifupdown...
[  OK  ] Started Helper to synchronize boot up for ifupdown.
[    9.874841] zram: Added device: zram0
         Starting Raise network interfaces...
[    9.876181] zram: Added device: zram1
[    9.877685] zram: Added device: zram2
[   10.005510] zram0: detected capacity change from 0 to 1991770112
[   10.124759] input: beeper as /devices/platform/beeper/input/input2
[  OK  ] Found device /dev/ttyS2.
[   10.192872] mc: Linux media interface: v0.10
[   10.218039] videodev: Linux video capture interface: v2.00
[   10.286014] rockchip-vop ff8f0000.vop: Adding to iommu group 2
[   10.290379] rockchip_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[   10.290740] rockchip-vop ff900000.vop: Adding to iommu group 3
[  OK  ] Started Raise network interfaces.
[   10.292854] rkvdec ff660000.video-codec: Adding to iommu group 1
[   10.294283] rockchip-rga ff680000.rga: HW Version: 0x03.02
[   10.298692] hantro_vpu: module is from the staging directory, the quality is unknown, you have been warned.
[   10.301683] hantro-vpu ff650000.video-codec: Adding to iommu group 0
[   10.303036] rockchip-rga ff680000.rga: Registered rockchip-rga as /dev/video0
[   10.303105] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-enc as /dev/video1
[   10.314184] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-dec as /dev/video3
[   10.378020] panfrost ff9a0000.gpu: clock rate = 500000000
[   10.383476] panfrost ff9a0000.gpu: mali-t860 id 0x860 major 0x2 minor 0x0 status 0x0
[   10.384177] panfrost ff9a0000.gpu: features: 00000000,100e77bf, issues: 00000000,24040400
[   10.384901] panfrost ff9a0000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7
[   10.385970] panfrost ff9a0000.gpu: shader_present=0xf l2_present=0x1
[   10.390270] OF: graph: no port node found in /i2c@ff3d0000/typec-portc@22
[   10.401048] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops [rockchipdrm])
[   10.402015] [drm] unsupported AFBC format[3231564e]
[   10.404440] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops [rockchipdrm])
[   10.405573] rockchip-drm display-subsystem: bound fec00000.dp (ops cdn_dp_component_ops [rockchipdrm])
[   10.407494] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[   10.407754] [drm] Initialized panfrost 1.1.0 20180908 for ff9a0000.gpu on minor 0
[   10.411279] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 1
[   10.415878] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[   10.418918] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/otg-port
[   10.431665] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[   10.432182] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 5
[   10.433045] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000010002010010
[   10.433933] xhci-hcd xhci-hcd.3.auto: irq 75, io mem 0xfe800000
[   10.434842] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[   10.435577] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   10.436212] usb usb5: Product: xHCI Host Controller
[   10.436642] usb usb5: Manufacturer: Linux 5.10.21-rockchip64 xhci-hcd
[   10.437208] usb usb5: SerialNumber: xhci-hcd.3.auto
[   10.442264] hub 5-0:1.0: USB hub found
[   10.442637] hub 5-0:1.0: 1 port detected
[   10.443325] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[   10.443827] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 6
[   10.444518] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[   10.445183] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[   10.446049] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[   10.446781] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   10.447417] usb usb6: Product: xHCI Host Controller
[   10.447848] usb usb6: Manufacturer: Linux 5.10.21-rockchip64 xhci-hcd
[   10.448414] usb usb6: SerialNumber: xhci-hcd.3.auto
[   10.449368] hub 6-0:1.0: USB hub found
[   10.449738] hub 6-0:1.0: 1 port detected
[   10.641728] cdc_acm 3-1.1:1.0: ttyACM0: USB ACM device
[   10.642961] usbcore: registered new interface driver cdc_acm
[   10.643461] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   10.709820] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[   10.770306] usb 4-1.4: reset SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[   10.914658] r8152 4-1.4:1.0 (unnamed net_device) (uninitialized): netif_napi_add() called with weight 256
[   10.930224] r8152 4-1.4:1.0 eth1: v2.14.0 (2020/09/24)
[   10.930698] r8152 4-1.4:1.0 eth1: This product is covered by one or more of the following patents:
[   10.930698]          US6,570,884, US6,115,776, and US6,327,625.
[   10.930698]
[   10.932308] usbcore: registered new interface driver r8152
[   10.956863] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[   11.077975] Adding 1945084k swap on /dev/zram0.  Priority:5 extents:1 across:1945084k SSFS
[   11.210740] zram1: detected capacity change from 0 to 52428800
[   11.426141] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[   11.854173] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work [rockchipdrm]] Not connected. Disabling cdn
[  OK  ] Started Armbian ZRAM config.
         Starting Armbian memory supported logging...
[   13.382593] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
[   13.383270] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
[   15.502991] random: crng init done
[   15.503317] random: 7 urandom warning(s) missed due to ratelimiting
[   15.578659] systemd[1]: Started Armbian memory supported logging.
[  OK  ] Started Armbian memory supported logging.
[   15.600697] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[   15.762359] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
         Starting Flush Journal to Persistent Storage...
[   15.827750] systemd-journald[687]: Received request to flush runtime journal from PID 1
[  OK  ] Started Flush Journal to Persistent Storage.
         Starting Create Volatile Files and Directories...
[  OK  ] Started Create Volatile Files and Directories.
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Entropy daemon using the HAVEGE algorithm.
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily rotation of log files.
         Starting Armbian hardware optimization...
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Started Helios64 UPS Shutdown timer on power loss.
[  OK  ] Started Daily apt download activities.
         Starting Armbian hardware monitoring...
[  OK  ] Started Daily man-db regeneration.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Started Daily apt upgrade and clean activities.
[  OK  ] Reached target Timers.
[  OK  ] Started Armbian hardware optimization.
[  OK  ] Started Armbian hardware monitoring.
[  OK  ] Reached target Basic System.
         Starting LSB: Load kernel …d to enable cpufreq scaling...
         Starting Login Service...
[  OK  ] Started Regular background program processing daemon.
         Starting rng-tools.service...
         Starting System Logging Service...
         Starting Dispatcher daemon for systemd-networkd...
         Starting fan speed regulator...
[  OK  ] Started D-Bus System Message Bus.
         Starting Network Manager...
         Starting WPA supplicant...
         Starting Resets System Activity Data Collector...
[  OK  ] Started rng-tools.service.
[  OK  ] Started System Logging Service.
[  OK  ] Started fan speed regulator.
[  OK  ] Started Resets System Activity Data Collector.
[  OK  ] Started Login Service.
[  OK  ] Started WPA supplicant.
[  OK  ] Started LSB: Load kernel m…ded to enable cpufreq scaling.
         Starting LSB: set CPUFreq kernel parameters...
[  OK  ] Started LSB: set CPUFreq kernel parameters.
         Starting LSB: Set sysfs variables from /etc/sysfs.conf...
[  OK  ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
[  OK  ] Started Network Manager.
[  OK  ] Reached target Network.
[  OK  ] Reached target Network is Online.
         Starting LSB: Advanced IEEE 802.11 management daemon...
         Starting /etc/rc.local Compatibility...
         Starting OpenBSD Secure Shell server...
[  OK  ] Started Unattended Upgrades Shutdown.
         Starting Permit User Sessions...
[  OK  ] Started LSB: Advanced IEEE 802.11 management daemon.
[  OK  ] Started /etc/rc.local Compatibility.
[  OK  ] Started Permit User Sessions.
         Starting Hostname Service...
[  OK  ] Started Serial Getty on ttyS2.
[  OK  ] Started Getty on tty1.
[  OK  ] Reached target Login Prompts.
         Starting Enable heartbeat …rk activity led on Helios64...
[  OK  ] Started Hostname Service.
[  OK  ] Started OpenBSD Secure Shell server.
[  OK  ] Started Enable heartbeat &…work activity led on Helios64.
         Starting Network Manager Script Dispatcher Service...
[  OK  ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
[  OK  ] Started Network Manager Script Dispatcher Service.
[  OK  ] Started Dispatcher daemon for systemd-networkd.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.
[   18.383098] rk_gmac-dwmac fe300000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=POLL)
[   18.387201] rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found
[   18.387881] rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW
[   18.388828] rk_gmac-dwmac fe300000.ethernet eth0: configuring for phy/rgmii link mode

Armbian 21.02.3 Buster ttyS2

helios64 login: [   22.466685] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   22.467478] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   33.761986] vcc5v0_typec: disabling
         Stopping Hostname Service...
[  OK  ] Closed Load/Save RF Kill Switch Status /dev/rfkill Watch.
         Stopping Authorization Manager...
[  OK  ] Stopped target Timers.
[  OK  ] Stopped Daily apt upgrade and clean activities.
[  OK  ] Stopped Daily rotation of log files.
[  OK  ] Stopped Daily Cleanup of Temporary Directories.
[  OK  ] Stopped Daily apt download activities.
[  OK  ] Stopped Daily man-db regeneration.
[  OK  ] Stopped target System Time Synchronized.
[  OK  ] Stopped target Graphical Interface.
[  OK  ] Stopped target Multi-User System.
         Stopping Dispatcher daemon for systemd-networkd...
         Stopping LSB: Advanced IEEE 802.11 management daemon...
         Stopping Regular background program processing daemon...
[  OK  ] Stopped target Login Prompts.
         Stopping Getty on tty1...
         Stopping Serial Getty on ttyS2...
         Stopping OpenBSD Secure Shell server...
         Stopping rng-tools.service...
         Stopping System Logging Service...
         Stopping Unattended Upgrades Shutdown...
         Stopping fan speed regulator...
[  OK  ] Stopped Resets System Activity Data Collector.
         Stopping LSB: Set sysfs variables from /etc/sysfs.conf...
[  OK  ] Stopped Regular background program processing daemon.
[  OK  ] Stopped System Logging Service.
[  OK  ] Stopped Dispatcher daemon for systemd-networkd.
[  OK  ] Stopped fan speed regulator.
[  OK  ] Stopped Unattended Upgrades Shutdown.
[  OK  ] Stopped Hostname Service.
[  OK  ] Stopped Serial Getty on ttyS2.
[  OK  ] Stopped Getty on tty1.
[  OK  ] Stopped OpenBSD Secure Shell server.
[  OK  ] Stopped Authorization Manager.
[  OK  ] Stopped Helios64 UPS Action.
[  OK  ] Stopped LSB: Advanced IEEE 802.11 management daemon.
[  OK  ] Stopped rng-tools.service.
[  OK  ] Stopped Helios64 UPS Shutdown timer on power loss.
[  OK  ] Removed slice system-getty.slice.
[  OK  ] Removed slice system-serial\x2dgetty.slice.
         Stopping Permit User Sessions...
[  OK  ] Stopped /etc/rc.local Compatibility.
[  OK  ] Stopped target Network is Online.
         Stopping Login Service...
[  OK  ] Stopped LSB: Set sysfs variables from /etc/sysfs.conf.
[  OK  ] Stopped Permit User Sessions.
[  OK  ] Stopped target Network.
         Stopping WPA supplicant...
         Stopping Network Manager...
         Stopping Raise network interfaces...
         Stopping LSB: set CPUFreq kernel parameters...
[  OK  ] Stopped Login Service.
[  OK  ] Stopped WPA supplicant.
[  OK  ] Stopped LSB: set CPUFreq kernel parameters.
[  OK  ] Stopped Network Manager.
         Stopping D-Bus System Message Bus...
         Stopping LSB: Load kernel …d to enable cpufreq scaling...
[  OK  ] Stopped D-Bus System Message Bus.
[  OK  ] Stopped Raise network interfaces.
[  OK  ] Stopped LSB: Load kernel m…ded to enable cpufreq scaling.
[  OK  ] Stopped target Remote File Systems.
[  OK  ] Stopped target Basic System.
[  OK  ] Stopped target Paths.
[  OK  ] Stopped target Slices.
[  OK  ] Removed slice User and Session Slice.
[  OK  ] Stopped target Sockets.
[  OK  ] Closed D-Bus System Message Bus Socket.
[  OK  ] Stopped target System Initialization.
[  OK  ] Stopped Apply Kernel Variables.
[  OK  ] Stopped Load Kernel Modules.
[  OK  ] Stopped target Local Encrypted Volumes.
[  OK  ] Stopped Forward Password R…uests to Wall Directory Watch.
         Stopping Armbian memory supported logging...
         Stopping Update UTMP about System Boot/Shutdown...
         Stopping Entropy daemon using the HAVEGE algorithm...
[  OK  ] Closed Syslog Socket.
[  OK  ] Stopped Entropy daemon using the HAVEGE algorithm.
         Stopping Load/Save Random Seed...
[  OK  ] Stopped Update UTMP about System Boot/Shutdown.
[  OK  ] Stopped Create Volatile Files and Directories.
[  OK  ] Stopped Load/Save Random Seed.
[  OK  ] Unmounted /var/log.
[  OK  ] Unmounted /var/log.hdd.
[  OK  ] Stopped Armbian memory supported logging.
         Stopping Armbian ZRAM config...
[  OK  ] Stopped Armbian ZRAM config.
[  OK  ] Stopped target Local File Systems.
         Unmounting /tmp...
[  OK  ] Unmounted /tmp.
[  OK  ] Stopped target Local File Systems (Pre).
[  OK  ] Stopped Create Static Device Nodes in /dev.
[  OK  ] Stopped Create System Users.
[  OK  ] Stopped Remount Root and Kernel File Systems.
[  OK  ] Stopped target Swap.
[  OK  ] Reached target Shutdown.
         Deactivating swap /dev/zram0...
[  OK  ] Deactivated swap /dev/zram0.
[  OK  ] Reached target Unmount All Filesystems.
[  OK  ] Reached target Final Step.
[  OK  ] Started Power-Off.
[  OK  ] Reached target Power-Off.
[   39.821756] printk: systemd-shutdow: 69 output lines suppressed due to ratelimiting
[   39.866469] systemd-shutdown[1]: Syncing filesystems and block devices.
[   39.889087] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[   39.895960] systemd-journald[687]: Received SIGTERM from PID 1 (systemd-shutdow).
[   39.909073] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[   39.916548] systemd-shutdown[1]: Unmounting file systems.
[   39.918884] [2132]: Remounting '/' read-only in with options 'errors=remount-ro,commit=600'.
[   39.934750] EXT4-fs (mmcblk1p1): re-mounted. Opts: errors=remount-ro,commit=600
[   39.948675] systemd-shutdown[1]: All filesystems unmounted.
[   39.949170] systemd-shutdown[1]: Deactivating swaps.
[   39.949679] systemd-shutdown[1]: All swaps deactivated.
[   39.950150] systemd-shutdown[1]: Detaching loop devices.
[   39.952406] systemd-shutdown[1]: All loop devices detached.
[   39.952898] systemd-shutdown[1]: Detaching DM devices.
[   40.005871] kvm: exiting hardware virtualization
[   40.089909] xhci-hcd xhci-hcd.3.auto: Host halt failed, -110
[   40.127724] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   40.128178] usb usb4: USB disconnect, device number 1
[   40.128621] usb 4-1: USB disconnect, device number 2
[   40.129056] usb 4-1.4: USB disconnect, device number 3
[   40.129626] r8152 4-1.4:1.0 eth1: Stop submitting intr, status -108
[   40.182839] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered
[   40.183352] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   40.183800] usb usb3: USB disconnect, device number 1
[   40.184243] usb 3-1: USB disconnect, device number 2
[   40.184678] usb 3-1.1: USB disconnect, device number 3
[   40.186686] xhci-hcd xhci-hcd.0.auto: USB bus 3 deregistered
[   40.187531] xhci-hcd xhci-hcd.3.auto: remove, state 4
[   40.187978] usb usb6: USB disconnect, device number 1
[   40.188692] xhci-hcd xhci-hcd.3.auto: USB bus 6 deregistered
[   40.189195] xhci-hcd xhci-hcd.3.auto: remove, state 4
[   40.189640] usb usb5: USB disconnect, device number 1
[   40.206351] xhci-hcd xhci-hcd.3.auto: Host halt failed, -110
[   40.206846] xhci-hcd xhci-hcd.3.auto: Host controller not halted, aborting reset.
[   40.207679] xhci-hcd xhci-hcd.3.auto: USB bus 5 deregistered
[   40.208470] reboot: Power down
[   40▒

 

Link to comment
Share on other sites

@Vin Based on the log you provided, the system is not crashing but powering off on its own ?! Something is triggering a poweroff 10sec after you finished to start. That's strange.

You sure it's not you who triggered the poweroff ? Or maybe the poweroff button on the front panel is being press by the sticker a bit ?

Link to comment
Share on other sites

As i said, by software it shouldnt be possible since its fresh installs, i even used older images.

 

The sticker can also be ruled out, since its on for months and before it was running, also i wasnt pushing anything.

 

I really dont understand what or why, but yesterday i let it run on the battery until it was drained, reapplied the cable and restarted some more, and at some point it was even starting from my old nand image again

 

didnt do a restart so far since im worried it wont come up anymore.

Link to comment
Share on other sites

On 3/2/2021 at 6:12 AM, aprayoga said:

@crosser please modify /boot/armbianEnv.txt and add/modify following lines:

 


verbosity=7
console=serial
extraargs=earlyprintk ignore_loglevel

 

It should make the serial console more verbose.

mortomanos is referring to Armbian Device Tree Overlays

 

Whether it is a coincidence, newer kernel after one of recent updates, or changed timing due to increased verbosity, but the system comes up all right after `reboot` command last few times. Knocking on wood. And thank you in any case!

Link to comment
Share on other sites

On 1/31/2021 at 8:43 AM, mortomanos said:

Support contacted me and gave me an armbian overlay, the first reboot did work without problems. I will observe further, but for now it looks good.

@mortomanos

 

Could you post the dt overlay support gave you for the helios64 back in 2021?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines