Jump to content

cubietruck: USB devices not found after updating


xinul

Recommended Posts

As a newbie here I'd first like to send greetings to all members and to send a big THANK YOU to the support team.

 

My problem is: After booting cubietruck and installing the updates the USB devices aren't recognized anymore.

  •  I'm using standard devices: wired Logitech mouse, wired Cherry keyboard.
  • Updating went smoothly and finished normally.
  • Immediately after it, at the console prompt the keyboard was already dead.
  • I rebooted repeatedly via HW switch because I couldn't log in and keyboard LEDs were also off.

 

My questions: What could I try to fix this?
 Is any important info missing?

 

Here is an extraction from `/var/log/messages`:

Jul  6 13:17:17 cubie kernel: [   16.343264] hub 5-0:1.0: USB hub found
Jul  6 13:17:17 cubie kernel: [   16.343339] hub 5-0:1.0: 1 port detected
Jul  6 13:17:17 cubie kernel: [   16.351875] Adding 1027124k swap on /dev/zram0.  Priority:5 extents:1 across:1027124k SSFS
Jul  6 13:17:17 cubie kernel: [   16.611900] cfg80211: Loading compiled-in X.509 certificates for regulatory database
Jul  6 13:17:17 cubie kernel: [   16.612550] Bluetooth: Core ver 2.22
Jul  6 13:17:17 cubie kernel: [   16.612745] NET: Registered protocol family 31
Jul  6 13:17:17 cubie kernel: [   16.612754] Bluetooth: HCI device and connection manager initialized
Jul  6 13:17:17 cubie kernel: [   16.612783] Bluetooth: HCI socket layer initialized
Jul  6 13:17:17 cubie kernel: [   16.612797] Bluetooth: L2CAP socket layer initialized
Jul  6 13:17:17 cubie kernel: [   16.612836] Bluetooth: SCO socket layer initialized
Jul  6 13:17:17 cubie kernel: [   16.630461] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
Jul  6 13:17:17 cubie kernel: [   16.635846] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
Jul  6 13:17:17 cubie kernel: [   16.635874] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
Jul  6 13:17:17 cubie kernel: [   16.694365] usb 4-1: new low-speed USB device number 2 using ohci-platform
Jul  6 13:17:17 cubie kernel: [   16.803666] usb 5-1: new low-speed USB device number 2 using ohci-platform
Jul  6 13:17:17 cubie kernel: [   16.886295] Bluetooth: HCI UART driver ver 2.3
Jul  6 13:17:17 cubie kernel: [   16.886316] Bluetooth: HCI UART protocol H4 registered
Jul  6 13:17:17 cubie kernel: [   16.886323] Bluetooth: HCI UART protocol BCSP registered
Jul  6 13:17:17 cubie kernel: [   16.886541] Bluetooth: HCI UART protocol LL registered
Jul  6 13:17:17 cubie kernel: [   16.886551] Bluetooth: HCI UART protocol ATH3K registered
Jul  6 13:17:17 cubie kernel: [   16.886622] Bluetooth: HCI UART protocol Three-wire (H5) registered
Jul  6 13:17:17 cubie kernel: [   16.886879] Bluetooth: HCI UART protocol Broadcom registered
Jul  6 13:17:17 cubie kernel: [   16.887224] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
Jul  6 13:17:17 cubie kernel: [   16.887538] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
Jul  6 13:17:17 cubie kernel: [   16.929566] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip BCM43362/1
Jul  6 13:17:17 cubie kernel: [   16.931485] usb 4-1: New USB device found, idVendor=046d, idProduct=c069, bcdDevice=56.01
Jul  6 13:17:17 cubie kernel: [   16.931507] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Jul  6 13:17:17 cubie kernel: [   16.931517] usb 4-1: Product: USB Laser Mouse
Jul  6 13:17:17 cubie kernel: [   16.931524] usb 4-1: Manufacturer: Logitech
Jul  6 13:17:17 cubie kernel: [   16.944758] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43362-sdio.cubietech,cubietruck.txt failed with error -2
Jul  6 13:17:17 cubie kernel: [   16.944780] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43362-sdio.cubietech,cubietruck.txt
Jul  6 13:17:17 cubie kernel: [   16.948566] input: Logitech USB Laser Mouse as /devices/platform/soc/1c14400.usb/usb4/4-1/4-1:1.0/0003:046D:C069.0001/input/input2
Jul  6 13:17:17 cubie kernel: [   16.949337] hid-generic 0003:046D:C069.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB Laser Mouse] on usb-1c14400.usb-1/input0
Jul  6 13:17:17 cubie kernel: [   17.052416] usb 5-1: New USB device found, idVendor=046a, idProduct=0023, bcdDevice= 2.20
Jul  6 13:17:17 cubie kernel: [   17.052440] usb 5-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Jul  6 13:17:17 cubie kernel: [   17.323547] Bluetooth: hci0: BCM: chip id 63
Jul  6 13:17:17 cubie kernel: [   17.326305] Bluetooth: hci0: BCM: features 0x07
Jul  6 13:17:17 cubie kernel: [   17.350489] Bluetooth: hci0: BCM20702A
Jul  6 13:17:17 cubie kernel: [   17.350521] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
Jul  6 13:17:17 cubie kernel: [   17.817602] zram1: detected capacity change from 0 to 52428800
Jul  6 13:17:17 cubie kernel: [   17.817791] cfg80211: failed to load regulatory.db
Jul  6 13:17:17 cubie kernel: [   18.159187] input: HID 046a:0023 as /devices/platform/soc/1c1c400.usb/usb5/5-1/5-1:1.0/0003:046A:0023.0002/input/input3
Jul  6 13:17:17 cubie kernel: [   18.219736] cherry 0003:046A:0023.0002: input,hidraw1: USB HID v1.11 Keyboard [HID 046a:0023] on usb-1c1c400.usb-1/input0
Jul  6 13:17:17 cubie kernel: [   18.221955] input: HID 046a:0023 as /devices/platform/soc/1c1c400.usb/usb5/5-1/5-1:1.1/0003:046A:0023.0003/input/input4
Jul  6 13:17:17 cubie kernel: [   18.234840] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip BCM43362/1
Jul  6 13:17:17 cubie kernel: [   18.238871] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-11), device may have limited channels available
Jul  6 13:17:17 cubie kernel: [   18.242440] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
Jul  6 13:17:17 cubie kernel: [   18.279402] cherry 0003:046A:0023.0003: input,hidraw2: USB HID v1.11 Device [HID 046a:0023] on usb-1c1c400.usb-1/input1
Jul  6 13:17:17 cubie kernel: [   19.395382] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard

 

At shutdown:

Jul  6 14:49:07 cubie kernel: [ 3071.800161] usb 4-1: USB disconnect, device number 2
Jul  6 14:49:07 cubie kernel: [ 3071.804241] usb 5-1: USB disconnect, device number 2


And here is the same extraction from the boot messages after updating:
 

Jul  6 15:04:45 cubie kernel: [   12.539805] hub 5-0:1.0: USB hub found
Jul  6 15:04:45 cubie kernel: [   12.539882] hub 5-0:1.0: 1 port detected
Jul  6 15:04:45 cubie kernel: [   12.788317] Bluetooth: hci0: BCM: chip id 63
Jul  6 15:04:45 cubie kernel: [   12.791099] Bluetooth: hci0: BCM: features 0x07
Jul  6 15:04:45 cubie kernel: [   12.814669] Bluetooth: hci0: BCM20702A
Jul  6 15:04:45 cubie kernel: [   12.814705] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000
Jul  6 15:04:45 cubie kernel: [   13.221320] zram1: detected capacity change from 0 to 52428800
Jul  6 15:04:45 cubie kernel: [   13.227066] cfg80211: failed to load regulatory.db
Jul  6 15:04:45 cubie kernel: [   13.242253] random: crng init done
Jul  6 15:04:45 cubie kernel: [   13.242275] random: 7 urandom warning(s) missed due to ratelimiting
Jul  6 15:04:45 cubie kernel: [   13.776907] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip BCM43362/1
Jul  6 15:04:45 cubie kernel: [   13.782054] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-11), device may have limited channels available
Jul  6 15:04:45 cubie kernel: [   13.783075] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
Jul  6 15:04:45 cubie kernel: [   14.244615] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard


My install image, the current state

user@host:$ cat armbian-image-release
# PLEASE DO NOT EDIT THIS FILE
BOARD=cubietruck
BOARD_NAME="Cubietruck"
BOARDFAMILY=sun7i
BUILD_REPOSITORY_URL=https://github.com/armbian/build
BUILD_REPOSITORY_COMMIT=79b790cf-dirty
DISTRIBUTION_CODENAME=buster
DISTRIBUTION_STATUS=supported
VERSION=20.11.6
LINUXFAMILY=sunxi
BRANCH=current
ARCH=arm
IMAGE_TYPE=stable
BOARD_TYPE=conf
INITRD_ARCH=arm
KERNEL_IMAGE_TYPE=Image
IMAGE_UUID=cce0e008-f223-41de-84a4-8a4f505cb5bc
user@host:$ cat armbian-release
# PLEASE DO NOT EDIT THIS FILE
BOARD=cubietruck
BOARD_NAME="Cubietruck"
BOARDFAMILY=sun7i
BUILD_REPOSITORY_URL=https://github.com/armbian/build
BUILD_REPOSITORY_COMMIT=428a20876-dirty
DISTRIBUTION_CODENAME=buster
DISTRIBUTION_STATUS=supported
VERSION=21.05.6
LINUXFAMILY=sunxi
ARCH=arm
IMAGE_TYPE=stable
BOARD_TYPE=conf
INITRD_ARCH=arm
KERNEL_IMAGE_TYPE=Image
BRANCH=current

 

B.t.w.: I tried it as an A20 bug report first but questions couldn't match my situation:

Does the system boot: Yes, but I can't provide the requested info nevertheless,
It's not a bug of a certain image but in the update process/of a certain package/of a certain post trigger.
So please give me a hint which category I could have chosen better.

Edited by xinul
typo
Link to comment
Share on other sites

  • xinul changed the title to cubietruck: USB devices not found after updating
This thread is quite old. Please consider starting a new thread rather than reviving this one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines