newsy Posted August 24, 2016 Posted August 24, 2016 device: orange pi pcsoft: Armbian_5.14_Orangepipc_Debian_jessie_3.4.112.7z my log via serial: U-Boot SPL 2016.05-armbian (Jun 05 2016 - 09:45:23) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2016.05-armbian (Jun 05 2016 - 09:45:23 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 (SD), SUNXI SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5: USB OHCI 1.0 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 2 for devices... 1 USB Device(s) found scanning bus 4 for devices... 1 USB Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 2444 bytes read in 182 ms (12.7 KiB/s) ## Executing script at 43100000 gpio: pin PL10 (gpio 298) value is 1 gpio: pin PG11 (gpio 203) value is 1 0 bytes read in 131 ms (0 Bytes/s) ** File not found /boot/.next ** ** Unrecognized filesystem type ** ** File not found .next ** 36192 bytes read in 516 ms (68.4 KiB/s) 3113891 bytes read in 3143 ms (966.8 KiB/s) 5064616 bytes read in 5070 ms (974.6 KiB/s) Kernel image @ 0x48000000 [ 0x000000 - 0x4d47a8 ] ## Loading init Ramdisk from Legacy Image at 42000000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 3113827 Bytes = 3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Using machid 0x1029 from environment Starting kernel ... [sun8i_fixup]: From boot, get meminfo: Start: 0x40000000 Size: 1024MB ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1 ion_reserve_select: ion chipid [0x2004620! ion_reserve_common: ion reserve: [0x50000000, 0x60000000]! Debian GNU/Linux 8 orangepipc ttyS0 orangepipc login: U-Boot SPL 2016.05-armbian (Jun 05 2016 - 09:45:23) DRAM: 1024 MiB Trying to boot from MMC1 mmc_load_image_raw_sector: mmc block read error SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### but after switch off/on power this work....problem only with command reboot or shutdown -r now device after this command not started please help
tkaiser Posted August 24, 2016 Posted August 24, 2016 Just a shot in the dark: Does rebooting work without serial console connected?
newsy Posted August 24, 2016 Author Posted August 24, 2016 Just a shot in the dark: Does rebooting work without serial console connected? I do not understand how serial console may interfere with read flash, but I checked out without serial console connected does not work.
tkaiser Posted August 24, 2016 Posted August 24, 2016 I do not understand how serial console may interfere with read flash Please read the last 2 paragraphs in the UART chapter: http://linux-sunxi.org/Pine64#Serial_port_.2F_UART We also had various clock/calibration issues that might be related to stuff like that. Anyway: I would upgrade Armbian (apt-get upgrade), then try again and if that doesn't help try another SD card (recommendations and procedure to choose AND TEST prior to using a card exist)
newsy Posted August 24, 2016 Author Posted August 24, 2016 I tried to do the update did not help, there are suspicions on sd-card tomorrow to test another flash card
Teazia Posted August 26, 2016 Posted August 26, 2016 This is a bit different but similar. How to boot after shutdown on OPI PC Plus? It seems I need to unplug the device before the start button works (or maybe it doesn't work at all and resetting power reboots?).
newsy Posted August 26, 2016 Author Posted August 26, 2016 I now test other two 8G sdcard, nothing has changed the problem persists, I can not understand what exactly I need to disconnect, as I have is connected only serial and eth (photo https://yadi.sk/i/GMJEPJ_QuVyFh)
tkaiser Posted August 26, 2016 Posted August 26, 2016 This is a bit different but similar. How to boot after shutdown on OPI PC Plus? It seems I need to unplug the device before the start button works (or maybe it doesn't work at all and resetting power reboots?). The power button is only there to wake from suspend, you would need to add a reset switch (or a physical switch disconnecting DC-IN completely) I now test other two 8G sdcard, nothing has changed the problem persists, I can not understand what exactly I need to disconnect, as I have is connected only serial and eth (photo https://yadi.sk/i/GMJEPJ_QuVyFh) Another shot in the dark (since you seem to be the only one with this phenomenon and struggle with just one Orange Pi PC -- always the same SD card slot used -- and only Armbian). You could try to use a thin peace of paper to get more pressure in the SD card slot (yeah, no idea what's different on cold vs. warm boot -- still 'shot in the dark' mode) or loboris' Ubuntu Mate image for OPi PC. The one approach tries to improve hardware (contacts in SD card slot), the other tries to get a clue whether different u-boot versions make the difference (Armbian uses mainline u-boot, nearly all other Orange Pi OS images an outdated u-boot version from 2009 which boots differently). And another shot in the dark: DRAM problems, please read through http://forum.armbian.com/index.php/topic/1322-testers-wanted-testing-dram-reliability-on-bpi-m2-and-nanopi-m1/?view=getlastpost (would then be the combination of a cold vs. warm boot issue with unreliable DRAM calibration that leads to u-boot failing to read from SD card). Since this is very unlikely please give a loboris image a try before (different DRAM calibration in this old u-boot version there)
Recommended Posts