Jump to content

[Solved] OPZero don't work then from first boot.


unlue

Recommended Posts

Hi all,

I beginner for OPZero, i followed steps and boot my device with Armbian 5.59 Ubuntu Bionic. It's running first boot no problem, i did login to ubuntu with serial, SSH, and some processes install armbianmonitor and connected port:8888 no problem but i did restart device, its no working. I plug TTL-usb and view serial monitor and this results: 

 

https://www.copypaste.io/detail?id=1538899137

U-Boot SPL 2018.05-armbian (Aug 21 2018 - 21:44:47 +0200)
DRAM: 512 MiB
Trying to boot from MMC1

U-Boot 2018.05-armbian (Aug 21 2018 - 21:44:47 +0200) Allwinner Technology

CPU: Allwinner H3 (SUN8I 1680)
Model: Xunlong Orange Pi Zero
DRAM: 512 MiB
MMC: SUNXI SD/MMC: 0
Loading Environment from EXT4… fs_devread read outside partition 4294967288
Failed to mount ext2 filesystem…

** Unable to use mmc 0:auto for loading the env **
Failed (-5)
In: serial
Out: serial
Err: serial
Net: phy interface0
eth0: ethernet@1c30000
fs_devread read outside partition 4294967288
Failed to mount ext2 filesystem…
** Unrecognized filesystem type **
fs_devread read outside partition 4294967288
Failed to mount ext2 filesystem…
** Unrecognized filesystem type **
starting USB…
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices… 1 USB Device(s) found
scanning usb for storage devices… 0 Storage Device(s) found
Autoboot in 1 seconds, press to stop
switch to partitions #0, OK
mmc0 is current device
fs_devread read outside partition 4294967288
Failed to mount ext2 filesystem…
** Unrecognized filesystem type **

Device 0: device type unknown
… is now current device
** Bad device usb 0 **
** Bad device usb 0 **
ethernet@1c30000 Waiting for PHY auto negotiation to complete. done
BOOTP broadcast 1
DHCP client bound to address 192.168.1.103 (22 ms)
*** Warning: no boot file name; using 'C0A80167.img'
Using ethernet@1c30000 device
TFTP from server 0.0.0.0; our IP address is 192.168.1.103; sending through gateway 192.168.1.1
Filename 'C0A80167.img'.
Load address: 0x42000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/01-02-42-43-d8-5d-93
*** ERROR: serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/C0A80167 *** ERROR:serverip' not set
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/C0A8016
*** ERROR: serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/C0A801 *** ERROR:serverip' not set
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/C0A80
*** ERROR: serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/C0A8 *** ERROR:serverip' not set
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/C0A
*** ERROR: serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/C0 *** ERROR:serverip' not set
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/C
*** ERROR: serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-sunxi *** ERROR:serverip' not set
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm
*** ERROR: serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/default *** ERROR:serverip' not set
Config file not found
BOOTP broadcast 1
DHCP client bound to address 192.168.1.103 (13 ms)
Using ethernet@1c30000 device
TFTP from server 0.0.0.0; our IP address is 192.168.1.103; sending through gateway 192.168.1.1
Filename 'boot.scr.uimg'.
Load address: 0x43100000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
=>

So how can I fix it issue?

 

Thank you for all. 

Edited by unlue
solved tag for topic
Link to comment
Share on other sites

i said, "i followed steps..." My SDCard is Class 10, 16GB and i tested with H2testw, result: 

Warning: Only 16 of 15351 MByte tested.
Test finished without errors.
Reading speed: 7.94 MByte/s
H2testw v1.4

and i did burn with Etcher... 

 

Device is working on first boot no problem. I did some process, download and install armbianmonitor, some test with apt-get... no problem. But I restart device (unplug power source ), after no working get error from first message...  

etcherdnm.jpg

Link to comment
Share on other sites

1 hour ago, unlue said:

i said, "i followed steps..."

I ask cause I could not repeat your issues:

Spoiler

freshly downloaded:


  ___                               ____  _   _____              
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |__  /___ _ __ ___  
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | |   / // _ \ '__/ _ \ 
| |_| | | | (_| | | | | (_| |  __/ |  __/| |  / /|  __/ | | (_) |
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| /____\___|_|  \___/ 
                       |___/                                     

Welcome to ARMBIAN 5.59 stable Ubuntu 18.04.1 LTS 4.14.65-sunxi   
System load:   0.37 0.22 0.08  	Up time:       1 min		
Memory usage:  10 % of 493MB  	IP:            192.168.0.22
CPU temp:      41°C           	
Usage of /:    5% of 15G  

reboot:


  ___                               ____  _   _____              
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |__  /___ _ __ ___  
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | |   / // _ \ '__/ _ \ 
| |_| | | | (_| | | | | (_| |  __/ |  __/| |  / /|  __/ | | (_) |
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| /____\___|_|  \___/ 
                       |___/                                     

Welcome to ARMBIAN 5.59 stable Ubuntu 18.04.1 LTS 4.14.65-sunxi   
System load:   0.51 0.23 0.09  	Up time:       1 min		
Memory usage:  11 % of 493MB  	IP:            192.168.0.22
CPU temp:      45°C           	
Usage of /:    6% of 15G    	

apt update && apt upgrade && reboot:


  ___                               ____  _   _____              
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |__  /___ _ __ ___  
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | |   / // _ \ '__/ _ \ 
| |_| | | | (_| | | | | (_| |  __/ |  __/| |  / /|  __/ | | (_) |
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| /____\___|_|  \___/ 
                       |___/                                     

Welcome to ARMBIAN 5.60 stable Ubuntu 18.04.1 LTS 4.14.70-sunxi   
System load:   1.83 0.45 0.15  	Up time:       0 min		
Memory usage:  11 % of 493MB  	IP:            192.168.0.22
CPU temp:      55°C           	
Usage of /:    6% of 15G    	

 

http://ix.io/1oA9

I did not power-cycle it (unplug) but as long as you didn't unplug it to early (means not properly shut-downed) this shouldn't have an impact.

 

1 hour ago, unlue said:

install armbianmonitor

is installed by default. Do you mean you installed cpuminer or RPi-Monitor from armbianmonitor?

 

1 hour ago, unlue said:

Warning: Only 16 of 15351 MByte tested.

 

 

16 out of 15351? sounds like the card wasn't properly formated prior to test. Please format your card (e.g. with SD Memory Card Formatter on windows) and then repeat H2testw.

 

 

 

Link to comment
Share on other sites

Thank you for interest @chwe, i did test SDcard again result: 

 

Quote

Warning: Only 15350 of 15351 MByte tested.
Test finished without errors.
You can now delete the test files *.h2w or verify them again.
Writing speed: 6.98 MByte/s
Reading speed: 15.0 MByte/s
H2testw v1.4
 

 

i did change OS with Debian, and try again.. but don't change result.... :(

Link to comment
Share on other sites

So you have Orange Pi Zero H2   and only connected ethernet.

 

short cable, different cable?

More than one PowerSupply to test?

Powering via GPIO pins ?

How hot is the SoC after the first boot ?

 

Or is it a  Orange Pi Zero +2 H3 ?

Edited by Tido
Which OPi Zero ?
Link to comment
Share on other sites

Hi @Tido

 

Yes i have OPZero h2... 

 

29 minutes ago, Tido said:

short cable, different cable?

Ethernet cable ~2m, PowerSupply ~75cm 

 

30 minutes ago, Tido said:

More than one PowerSupply to test?

 

i try devide powering:

 

1- USB from PC via microUSB socket.  
2- USB from PC via GPIO 
3- USB from phone charger 5v2a via microUSB socket. 

 

 

35 minutes ago, Tido said:

How hot is the SoC after the first boot ?

 

Not much 35~45 Degree C. 

Link to comment
Share on other sites

15 minutes ago, unlue said:

1- USB from PC via microUSB socket.  
2- USB from PC via GPIO 

:wacko:  I power my Ardunio from PC, but never ever would I try to power an SBC with the PC = these two option do not count.

So you have only tried with one (1) phone charger  :blink: as a conclusion.

 

Do you have another phone charger?  and try it via GPIO, you may have to re-flash the SDcard as it might be corrupted now.

 


you might want to give the   Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113.7z   a chance as well if above steps are not sucessful:

https://dl.armbian.com/orangepizero/archive/

 

Link to comment
Share on other sites

18 hours ago, unlue said:

PowerSupply ~75cm 

likely to be a powering issue.. Is a AWG number printed on your cable? E.g. looks like this one:

28AWG.jpg.504c76898cdaf9162d4ea53360b1b2fd.jpg

 

if yes and it's higher than 22 go through this one:

to get a clue why it's bad idea. If there's no number on it.. chances are high that it is a crappy cable as well.. And I would look for better microUSB cables. 

 

With good cables, powering from my notebooks USB work without issues (not that I recommend it) with crappy cable no chance. If you have a multimeter, check voltage on one of the GND and 5V pins. 

ef9fb49d0e1f67acd5f09572001179eb.jpg

 

Link to comment
Share on other sites

Today i went to university laboratory and using controllable power supply and avometer, set value 5.0-5.10V and pluged to device via GPIO / microUSB,  and measured pins its using between 4.6-5.0V... and max. 0,35A.. but problem is contiune... 

 

i dont understand.. where is problem...  I think change Sdcard maybe problem is it. 

Link to comment
Share on other sites

Hi friends, finally i fix it. So im so sorry for occupy you... Problem is powersupply with cable...

i did try diferent cables,  and finally fixed by thin usb charge cable ~20awg i using power source pc-usb and no problem it's working... 

 

Thank you all for ur interesting... 

 

:):):) 

photo_2018-10-10_12-39-06.jpg

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines