Tantalum
-
Posts
13 -
Joined
-
Last visited
Content Type
Forums
Store
Crowdfunding
Applications
Events
Raffles
Community Map
Posts posted by Tantalum
-
-
Quote
Err:35 http://cdn-fastly.deb.debian.org/debian buster-backports/main armhf Contents (deb)
Hash Sum mismatch
Hashes of expected file:
- Filesize:2795533 [weak]
- SHA256:15f530a047e49a52284cce318630a8acb7879ebab95ecd28b8b660ba17dcbb94
Hashes of received file:
- SHA256:8c74979f1ac7600e494d33fda829dd2b5081b095f4c25889435c247247f8a549
- Filesize:2795533 [weak]
Last modification reported: Sat, 16 Nov 2019 14:01:28 +0000
Release file created at: Sat, 16 Nov 2019 14:29:08 +0000 -
I have tried with 2 different SD cards (Samsung Evo Plus), 2 different card readers and updated Etcher and Win32DiskImager.
File hash is also ok.
-
Hello
I having some issues with the Armbian Buster image for Nano Pi Neo 2.
https://www.armbian.com/nanopi-neo-2/
When I launch the command sudo apt update, I'm getting the following error:
The package cache file is corrupted, it has the wrong hash
I already downloaded the image several times, I still getting the same error.
My SD card is ok, I have tried with 2 different ones.
I can remember having the same issue with a preview version.
What's wrong???
Thank you
-
On 9/15/2018 at 11:39 AM, hjc said:
Not yet, recently I'm trying to use M4 (with mainline kernel) as a network router & gateway (connect 2-3 RTL8153, set up VLAN, routing, NAT, and site to site VPN), and still trying to resolve some USB related issues. Currently with mainline kernel the USB hub must be manually reset (USBDEVFS_RESET) after reboot, or it wouldn't be usable.
With OpenWRT, by any chance?
I'm searching for someone who would make the M4 and Neo4 compatible with OpenWRT (ideal board for LTE M.2 modems which uses USB3 or PCIe)
-
On 2/14/2019 at 6:49 PM, NicoD said:
The board started smelling burned. I'm not going to try it again. That's why you need to raise the heatsink so air can flow underneath it.
On 2/14/2019 at 7:29 PM, TonyMac32 said:Heatsink over is better than heatsink under due to basic physics.
Well, the basic physics also allows you to flip the board by 180° like this:
https://reho.st/self/dbe8a2f2236732bc929bedb89fd627a5bf0d2bac.jpg
I also replaced the original thermal sheet, by a 1.5mm copper sheett + thermal grease.
40min to reach 80° at full load. Never smelled burned.
https://reho.st/self/028b5abe980510d83950ceb82cf36153e44f91d3.png
On 2/14/2019 at 3:10 PM, balbes150 said:Do not understand the rejection of PCi (NVME) and the use of non-standard eMMC modules that have reduced speed and reliability.
The reason is simple, the Amlogic S922 doesn't support PCIe:
About the N2, the SoC seems to be very interesting, the lack of PCIe is indeed disturbing, but except for storage, there is no really need for it, USB 3 can do the job.
Personally I never liked the board design of the N- series. The boards are too big, they are huge, they are as big as an Intel NUC.
Do you think that FriendlyArm may release a board using the same SoC in the near future? Because I like the compact format of their M4 and Neo's.
-
14 hours ago, NicoD said:
You've got an undervoltage before it goes into the board.
I wonder what your USB voltage is?IDLE :
VDD_5V : 5.05V
VCC5V0_SYS : 5.03V
FULL:
VDD_5V : 4.85V
VCC5V0_SYS : 4.80V
Powered with a Meanwell GS25E-05, 16AWG wires (12.5mOhm/m).
The VDD_5V goes through the AO3415A mosfet. According to the specs it has a 42mOhm Rds(on). That mean a loss of 0.02V@idle and 0.1V@load.
I haven't measured the USB 5V voltage, but it's directly connected to VDD_5V over a RT9724GQW load switch I think (Rds(on): 100mOhm),
-
-
1 hour ago, sfx2000 said:
I wonder if they have a straight adapter - that 90 degree angle can put torque on a connector that might not be staked thru (speaking in general terms)
-
mmh
I think there are some major misunderstanding here about the USB-C power supply.
1. The problem about the under voltage at the input of the board are the thin wires of the USB cable...
Solution?
Do not use USB cable to power the M4 board, just use a descent barrel Jack DC power supply (for example: Meanwell)
2. Do we have to power the board over the pin header?
No, not necessary.
The USB-C connector is rated for 5A, physically! Not 3A. The 3A limitation is a question of wiring limitation of the standard USB-C cable, not the connector itself (and hypothetically the PCB traces of the board)
The missing support for USB-PD isn't an issue either. Don't use USB-C power supplies, it's that simple as that. Again, just use a descent barrel Jack DC power supply! And if possible a 5.1V or 5.2V one.
You only need a cheap USB-C DC jack adapter (which causes also probably a weak voltage drop):
Now, about the USB 3.0 connectors. Well indeed, at load there is a voltage drop on the board, especially on heavy load, and they are partially caused by the mosfets on the power rail on the board I think.
edit:
VDD_5V goes through the AO3415A mosfet to power the board. It has a 42mOhm Rds(on). which caused alone a 0.1V drop at full load of the M4 board (2A).
The USB 3.0 port uses a RT9724GQW load switch which has a Rds(on) of 100mOhm. That causes another 0.1V loss at 1A load.
-
Hello
Can someone explain me the purpose of the PWR_KEY on the M4/NEO board please?
Even after checking the schema and the PMIC datasheet I still don't fully understand how it works exactly.
Does it act as an reset?
Or does it act like a regular power button on a PC, in other words, it tells the OS to properly shutdown, to avoid data corruption.
Thank you
-
Hello
Any idea when the NEO4 will be available for sale?
-
On 8/24/2018 at 5:08 PM, wtarreau said:
I just checked the Wiki and it's clearly written dual-channel for the RAM regardless of the size, so we have 64 bits.
Those Ram chips have a 16bit bus each, not 32bit.
I hope they will design a 2GB Neo 4 version
, 1GB Ram is clearly not enough for such a SoC 
Quectel LTE modem support?
in Beginners
Posted · Edited by Tantalum
Hello
I'm using armbian on a Neo 2 board and I wanted to use a Quectel EM05 or EC25 LTE modem with it. Actually only need the serial port to send AT-commands.
My question is, are Quectel modems natively supported by armbian (QMI? MBMI? ), or do I need to add the driver manually and rebuild the image???
Thank you
(Yeah, it's a noob question
)
Edit:
Ok, I connected to modem to the board and realized that a wwan0 interface was created. That's fine, but I actually needed the serial port ttySx in order to sen AT-commands, but there is not one available... that's actually very strange.