-
Posts
7 -
Joined
-
Last visited
Content Type
Forums
Store
Crowdfunding
Applications
Events
Raffles
Community Map
Posts posted by Gabriel Zanetti
-
-
@armbianorange2hero i some tests and with img in download page can works fine, but hdmi and wifi not, i try to compile my own img too, but haven't knowledge with linux. I tested img from orange pi (debian with new kernel) and all functions works fine
-
Hi, i have try but still HDMI not work, and i discovery the wifi doesn't work too, i put this board the side for while, i'm going to study more about this topic and try again later, very thx for you time and help
-
4 minutes ago, schwar3kat said:
Hi Gabriel,
I just checked the config for your legacy kernel. CAN is not available, nor is the driver. I suspect that you will need to use current kernel for this driver.
You can search these forums to see if there are issues with the current kernel and if there are perhaps ways to get it working.
It may be that issues with the new kernel have not been resolved for your board, or you may find that someone has got it working.
the Armbian build system is an ideal platform for you to develop solutions, providing an easy way to apply patches and stream improvements into the build via Github pull requests.
I don't have your board, so won't be of much help.very thx for the help, i try the new kernel and i can bring up can0 interface, but, my board doesn't have hdmi output, and green led on board don't turn on, only red light is on, but by serial-usb i can configure every thing, i'm going study more about whats causes this, again, very thx for your help
-
1 minute ago, schwar3kat said:
You appear to be using a legacy kernel and a custom build. Where did you get it?
It is unlikely that legacy kernels support gs_usb otb.
I don't know of a way to add this after compile.
I suggest that you try https://www.armbian.com/orange-pi-zero-2/Armbian 22.05 Jammy Kernel 5.15.y
i download in archive, i tried to use the new version, but the boards stuck in armbian boot img, i try again but use usb-serial to see any msg error on boot sequence
-
1 hour ago, schwar3kat said:
Hi Gabriel,
You haven't given much information....
I don't own the same board as you and I know nothing about your CAN module.
The current Armbian builds include the kernel gs_usb driver module which is apparently required for your CAN module.
If you are using a current build then it is probable that you can activate the kernel driver module with "sudo modprobe gs_usb". This should enable the module, unless it needs some options configured (Google it).To confirm that the driver is loaded "sudo modprobe gs_usb --first-time" should return "modprobe: ERROR: could not insert 'gs_usb': Module already in kernel"
After this you should be able to use the driver.
Not required, but using the Armbian build system, it is possible to include the driver module permanently into the kernel if you compile it after modifying CONFIG_CAN_GS_USB=m to CONFIG_CAN_GS_USB=y in your board's kernel config file. If you did this then it wouldn't need modprobe to activate it.
Good luck
KatHi Kat, sorry, i have a orangepi zero 2 running Armbian 22.02.0-trunk.0046 with kernel Linux 4.9.255-sun50iw9, usb to can board https://github.com/bigtreetech/U2C , i tried run modprobe comand and this is the return modprobe: FATAL: Module gs_usb not found in directory /lib/modules/4.9.255-sun50iw9 . I'm can install gs_usb without compile new build? i very new with linux. Thx for your help
-
i've try to use a board usb to can, but every topic i see about can and armbian is with spi to can. I very beginner with sbc and armbian. This is the firmware it's runningin board usb-can https://github.com/candle-usb/candleLight_fw
USB to CAN adaptor
in Orange Pi Zero 2
Posted
i was imagine that, but i don't know how to implement dfs in custom kernel, for now i using official debian provided by orange pi, with new kernel and all functions works fine, thanks for all help you guys.