Same situation here. Updated to jammy => Orange Pi zero 1 does not boot anymore.
The serial port definitely gives an echo (local echo is deactivated) and runs at 115200 - but
nothing else happens.
U-Boot SPL 2017.11-armbian (Jan 25 2018 - 08:04:30)
DRAM: 512 MiB
Trying to boot from MMC1
U-Boot 2017.11-armbian (Jan 25 2018 - 08:04:30 +0100) Allwinner Technology
CPU: Allwinner H3 (SUN8I 1680)
Model: Xunlong Orange Pi Zero
DRAM: 512 MiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface0
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Autoboot in 1 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3708 bytes read in 197 ms (17.6 KiB/s)
## Executing script at 43100000
U-boot loaded from SD
Boot script loaded from mmc
278 bytes read in 149 ms (1000 Bytes/s)
9290667 bytes read in 1014 ms (8.7 MiB/s)
6972808 bytes read in 788 ms (8.4 MiB/s)
Found mainline kernel configuration
31935 bytes read in 787 ms (39.1 KiB/s)
339 bytes read in 862 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-analog-codec.dtbo
382 bytes read in 286 ms (1000 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-cir.dtbo
374 bytes read in 620 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-i2c0.dtbo
374 bytes read in 869 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-i2c1.dtbo
374 bytes read in 720 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-i2c2.dtbo
780 bytes read in 784 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-spi-spidev.dtbo
506 bytes read in 745 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-uart1.dtbo
506 bytes read in 427 ms (1000 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-uart2.dtbo
506 bytes read in 277 ms (1000 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-uart3.dtbo
504 bytes read in 389 ms (1000 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-usbhost0.dtbo
504 bytes read in 496 ms (1000 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-usbhost1.dtbo
504 bytes read in 703 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-usbhost2.dtbo
504 bytes read in 796 ms (0 Bytes/s)
Applying kernel provided DT overlay sun8i-h3-usbhost3.dtbo
799 bytes read in 325 ms (2 KiB/s)
Applying kernel provided DT overlay sun8i-h3-w1-gpio.dtbo
4179 bytes read in 810 ms (4.9 KiB/s)
Applying kernel provided DT fixup script (sun8i-h3-fixup.scr)
## Executing script at 44000000
## Loading init Ramdisk from Legacy Image at 43300000 ...
Image Name: uInitrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9290603 Bytes = 8.9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Loading Ramdisk to 49723000, end 49fff36b ... OK
reserving fdt memory region: addr=43000000 size=6e000
Loading Device Tree to 496b2000, end 49722fff ... OK
Starting kernel ...
