[BPP stucks during boot]

No, I didn't build or compile anything myself. I also did not touch sources.list ...

Just took the image file Armbian_5.25_Bananapipro_Ubuntu_xenial_next_4.9.7 from https://dl.armbian.com/bananapipro/

[BPP stucks during boot]

This problem is still not solved, so I started over with a fresh clean Ubuntu Xenial (next) image. Even with a new installation I get the same error messages for brcmfmac, but this time it started as expected...
But after apt-get upgrade / dist-upgrade and installing some software (apache2, zsh, logwatch, fail2ban, ...) it brings me back to the same problem during the boot process:
It just boots to the emergency mode after 100 seconds.

I already checked the file system of my MultiMediaCard but fsck -pvcf /dev/sdc1 and dumpe2fs -b /dev/sdc1 did not show any bad blocks and did not solve the problem.

 

:-( Any advice?

[BPP stucks during boot]

Hello,

I run Armbian (Ubuntu) on my Banana Pi Pro.

-> uname -a
Linux bananapipro 4.10.12-sunxi #7 SMP Wed Apr 26 02:44:12 CEST 2017 armv7l armv7l armv7l GNU/Linux

Since the last days the boot process stops. The BPP shows the followings lines on screen:

[   10.943882] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
[   11.233049] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30)
[   13.348258] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30)
[  100.212252] rc_core: Can't enable IR protocol cec

After second 100 I'm asked for the root password to "investigate" the situation. I think some timeout is reached here. The boot process will not complete then.

dmesg log tells me the same:

...
[   10.516930] Registered IR keymap rc-empty
[   10.517393] input: sunxi-ir as /devices/platform/soc@01c00000/1c21800.ir/rc/rc0/input3
[   10.517421] rc rc0: sunxi-ir as /devices/platform/soc@01c00000/1c21800.ir/rc/rc0
[   10.568886] sunxi-ir 1c21800.ir: initialized sunXi IR driver
[   10.620132] lirc_dev: IR Remote Control driver registered, major 244
[   10.652900] systemd-journald[295]: Received request to flush runtime journal from PID 1
[   10.657929] rc rc0: lirc_dev: driver ir-lirc-codec (sunxi-ir) registered at minor = 0
[   10.657945] IR LIRC bridge handler initialized
[   10.691597] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[   10.943882] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
[   11.233049] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30)
[   13.348258] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30)
[   14.600129] random: crng init done
[   98.517809] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
[   98.517840] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
[   98.517858] sun7i-dwmac 1c50000.ethernet eth0: fail to init PTP.
[   98.518389] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   99.692560] IR RC5(x/sz) protocol handler initialized
[   99.753070] IR NEC protocol handler initialized
[   99.814714] IR RC6 protocol handler initialized
[   99.872026] IR JVC protocol handler initialized
[   99.930764] IR Sony protocol handler initialized
[   99.992782] IR SANYO protocol handler initialized
[  100.049599] IR Sharp protocol handler initialized
[  100.110790] input: MCE IR Keyboard/Mouse (sunxi-ir) as /devices/virtual/input/input4
[  100.113104] IR MCE Keyboard/mouse protocol handler initialized
[  100.169823] IR XMP protocol handler initialized
[  100.212252] rc_core: Can't enable IR protocol cec
[ 1003.301594] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1003.301665] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1021.887164] IPv6: ADDRCONF(NETDEV_UP): bond0: link is not ready

First, I thought brcmfmac and the WiFi interface stop the boot process. So, I blocked the module brcmfmac as an experiment, but it makes no difference.

 

How to go on here?

Thank you for your help!