Search the Community

Hi, I was just wondering if anyone else out there with a Win+ has this issue .... when I install from an image file all works well, WIFI etc all good. But when I upgrade the install wlan0 etc has gone. ifconfig doesnt show it, lsmod shows the brcmfmac/cfg80211 I've tried it with a few of the recent image files systemctl status systemd-modules-load systemd-modules-load[1693]: Failed to find module 'lp' systemd-modules-load[1693]: Failed to find module 'ppdev' systemd-modules-load[1693]: Failed to find module 'parport_pc' root@zoot: lsmod Module Size Used by ipt_MASQUERADE 16384 1 nf_nat_masquerade_ipv4 16384 1 ipt_MASQUERADE iptable_nat 16384 1 nf_conntrack_ipv4 16384 2 nf_defrag_ipv4 16384 1 nf_conntrack_ipv4 nf_nat_ipv4 16384 1 iptable_nat nf_nat 28672 2 nf_nat_masquerade_ipv4,nf_nat_ipv4 nf_conntrack 118784 5 nf_conntrack_ipv4,ipt_MASQUERADE,nf_nat_masquerade_ipv4,nf_nat_ipv4,nf_nat libcrc32c 16384 2 nf_conntrack,nf_nat brcmfmac 212992 0 brcmutil 16384 1 brcmfmac cfg80211 266240 1 brcmfmac rfkill 28672 2 cfg80211 root@zoot:~# ifconfig -a eth0 Link encap:Ethernet HWaddr 02:ba:0e:f7:30:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 TX bytes:0 (0.0 eth0:avahi Link encap:Ethernet HWaddr 02:ba:0e:f7:30:ef inet addr:169.254.10.39 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1423 errors:0 dropped:0 overruns:0 frame:0 TX packets:1423 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:116295 (116.2 KB) TX bytes:116295 (116.2 KB)

Hi. I've got a Orange Pi Win Plus flashed with armbian, everything is running great, except the bluetooth module. I have everything installed, but blueman keeps telling me that no adapters are found. I've checked if the bluetooth adapters were on with the command 'armbian-config', as well as trying to stop and restart it with '/etc/init.d/bluetooth stop and start'. I start to feel like it won't work on linux, because I've already tried debian and ubuntu from the orangepi downloads page and the bluetooth didn't work too. I don't want to run Android just because of this issue. Any ideas?

Has anyone been able to successfully install rpimonitor on an Orange Pi Win Plus (A64)? I have been able to install it, but I get a lot of invalid readings. As you can see in the screenshot, it is not able to detect cpu frequency, vcore and temperature.

I was curious to see how Mainline kernel performs on GbE test against a Legacy kernel. For the Armbian side i chose the nightly dev Armbian_5.27.170602_Orangepiwin_Ubuntu_xenial_dev_4.11.1_desktop.img (Desktop) and for the Legacy i chose my own build with all "Bells and whistles" (full Desktop, hdmi, camera, bt and wifi). I did not optimized Armbian Mainline, just installed and run stock. For the Legacy i optimized as usual. If there is some optimization to do on Mainline side, i missed. I have some observations about the board and results: * Board is without Heat-sink, * Legacy subsequent test got lower values, i suspect it runs hotter than Mainline, maybe due to HDMI, camera and BT enabled, drops about 30~50 MBits/sec, * After Mainline installation, the next boot came without HDMI output, so i had to guess which IP was assigned without looking at router (OK, we know it is a development Image), * Board act as a Server (iperf3 -s) and my ultra fast Duo core Intel box as a client. * Both Image are build with gcc 6.3 Armbian Mainline kernel 4.11.1 results: Legacy kernel 3.10.105 results: