Joey Pongallo Posted June 1, 2022 Share Posted June 1, 2022 It looks like the May 28th release produced issues. I tried using the images on the OrangePI Zero 2 and the led only stays red. The prior version worked with no issue. 0 Quote Link to comment Share on other sites More sharing options...
cristobalgh Posted June 2, 2022 Share Posted June 2, 2022 +1 0 Quote Link to comment Share on other sites More sharing options...
Adam E Posted June 13, 2022 Share Posted June 13, 2022 [98]HELLO! BOOT0 is starting May 13 2020 14:10:04! [103]BOOT0 commit : 593cf83 [105]set pll start [108]periph0 has been enabled [111]set pll end [113]unknow PMU [115]PMU: AXP806 [122]vaild para:1 select dram para0 [125]board init ok [127]DRAM BOOT DRIVE INFO: V0.52 [130]the chip id is 0x5000 [133]chip id check OK [135]DRAM_VCC set to 1500 mv [139]read_calibration error [143]read_calibration error [147]read_calibration error [151]read_calibration error [155]read_calibration error [159]read_calibration error [163]read_calibration error [167]read_calibration error [171]read_calibration error [175]read_calibration error [177]retraining final error [182][AUTO DEBUG]32bit,1 ranks training success! [189]DRAM CLK =720 MHZ [192]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [198]Actual DRAM SIZE =1024 M [201]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [214]DRAM simple test OK. [217]rtc standby flag is 0x0, super standby flag is 0x0 [222]dram size =1024 [224]*****dram handle ok**** [228]card no is 0 [229]sdcard 0 line count 4 [232][mmc]: mmc driver ver 2019-12-19 10:41 [236][mmc]: sdc0 spd mode error, 2 [240][mmc]: set f_max to 50M, set f_max_ddr to 25M [245][mmc]: mmc 0 bias 0 [253][mmc]: Wrong media type 0x0 [256][mmc]: ***Try SD card 0*** [266][mmc]: HSSDR52/SDR25 4 bit [269][mmc]: 50000000 Hz [271][mmc]: 29819 MB [273][mmc]: ***SD/MMC 0 init OK!!!*** [372]Loading boot-pkg Succeed(index=0). [376]Entry_name = u-boot [385]Entry_name = monitor [389]Entry_name = dtbo [392]Entry_name = dtb [396]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-armbian (May 28 2022 - 09:09:02 +0000) Xunlong Software [00.472]CPU: Allwinner H616 [00.475]Model: Orange Pi Zero 2 I2C: ready [00.479]DRAM: 1 GiB Relocation Offset is: 35ec7000 [00.520]secure enable bit: 0 [00.523]PMU: AXP806 [00.528]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.710]sunxi overlay merged okqv [00.713]drv_disp_init [00.742]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [00.748]drv_disp_init finish [00.750]gic: sec monitor mode [00.756]flash init start [00.758]workmode = 0,storage type = 1 [00.761]MMC: 0 [00.762][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.769][mmc]: get sdc_type fail and use default host:tm1. [00.779][mmc]: Using default timing para [00.783][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.801][mmc]: card_caps:0x3000000a [00.804][mmc]: host_caps:0x3000003f [00.808]sunxi flash init ok [00.811]Loading Environment from FAT... [00.815][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.821][mmc]: get sdc_type fail and use default host:tm1. [00.831][mmc]: Using default timing para [00.835][mmc]: SUNXI SDMMC Controller Version:0x40200 ** Bad device mmc 1 ** Failed (-5) [00.846]usb burn from boot delay time 0 weak:otg_phy_config [00.859]usb prepare ok [01.663]overtime [01.667]do_burn_from_boot usb : no usb exist [01.671]boot_gui_init:start 141 bytes read in 15 ms (8.8 KiB/s) Set HDMI disp_mode to 1080p60 141 bytes read in 14 ms (9.8 KiB/s) Set fb0_width to 1280 Set fb0_height to 720 [01.986]boot_gui_init:finish [01.989]bmp_name=/boot/boot.bmp 230454 bytes read in 38 ms (5.8 MiB/s) [02.041]update dts Net: [02.044]No ethernet found. Hit any key to stop autoboot: 1 0 no mmc device at slot 1 [03.071][mmc]: card_caps:0x3000000a [03.074][mmc]: host_caps:0x3000003f switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 3202 bytes read in 18 ms (172.9 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 141 bytes read in 14 ms (9.8 KiB/s) 262144 bytes read in 45 ms (5.6 MiB/s) ** File not found /boot/dtb/allwinner/overlay/-fixup.scr ** 6995211 bytes read in 610 ms (10.9 MiB/s) ** File not found /boot/Image ** Unknown command 'booti' - try 'help' SCRIPT FAILED: continuing... No ethernet found. missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-sunxi No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default No ethernet found. Config file not found No ethernet found. armbian# UART output trying to boot from 28/05/2022 images. 0 Quote Link to comment Share on other sites More sharing options...
armbianorange2hero Posted June 15, 2022 Share Posted June 15, 2022 Same here. The 22.02 image works but is also dead after apt upgrade. 0 Quote Link to comment Share on other sites More sharing options...
armbianorange2hero Posted June 16, 2022 Share Posted June 16, 2022 (edited) Workaround: Install https://armbian.systemonachip.net/archive/orangepizero2/archive/Armbian_22.02.2_Orangepizero2_bullseye_legacy_4.9.255.img.xz and put the 22.05 packages on hold before upgrade: apt list --upgradable|fgrep 22.05| awk -F "/" '{print $1}' | xargs -n1 -i{} apt-mark hold {} apt-unhold armbian-zsh apt upgrade Reading package lists... Done Building dependency tree... Done Reading state information... Done Calculating upgrade... Done The following packages have been kept back: armbian-bsp-cli-orangepizero2 armbian-config armbian-firmware linux-dtb-legacy-sun50iw9 linux-image-legacy-sun50iw9 linux-libc-dev linux-u-boot-orangepizero2-legacy ... Edited June 16, 2022 by armbianorange2hero Added URL for 22.02 image 0 Quote Link to comment Share on other sites More sharing options...
Dominik Posted August 14, 2022 Share Posted August 14, 2022 @armbianorange2hero thank you for this. Do I need to hold back packages before every apt upgrade or only once? 0 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.