hkkok Posted November 3, 2022 Posted November 3, 2022 Recently i've download and installed Armbian_22.08.7_Bananapim5_bullseye_edge_5.19.16_minimal.img into Banana Pi M5 board. Initial setup run smoothly. After run the reboot command the system stop halfway. Can I know how to solve this problem? I have copy the error message below. Thanks. U-Boot 2022.07-armbian (Oct 18 2022 - 07:30:35 +0000)bpi-m5 Model: Banana Pi BPI-M5 SoC: Amlogic Meson SM1 (S905X3) Revision 2b:c (10:2) DRAM: 3.8 GiB Core: 385 devices, 27 uclasses, devicetree: separate MMC: sd@ffe05000: 0, mmc@ffe07000: 1 Loading Environment from nowhere... OK In: serial Out: serial Err: serial Net: eth0: ethernet@ff3f0000 Autoboot in 2 seconds switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 8147 bytes read in 3 ms (2.6 MiB/s) ## Executing script at 08000000 U-boot default fdtfile: amlogic/meson-sm1-bananapi-m5.dtb Current variant: 161 bytes read in 2 ms (78.1 KiB/s) Current fdtfile after armbianEnv: amlogic/meson-sm1-bananapi-m5.dtb Mainline bootargs: root=UUID=d0c122f6-b8a9-4650-94c2-77c85521b2d8 rootwait rootfstype=ext4 splash=verbose console=ttyAML0,115200 console=tty1 consoleblank=0 coherent_pool=2M loglevel=1 ubootpart=79a75e49-01 libata.force=noncq usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u cgroup_enable=memory swapaccount=1 19116246 bytes read in 838 ms (21.8 MiB/s) mmc fail to send stop cmd ** fs_devread read error - block Failed to load '/boot/Image' ** fs_devread read error - block Failed to mount ext2 filesystem... Can't set block device libfdt fdt_check_header(): FDT_ERR_BADMAGIC No FDT memory address configured. Please configure the FDT address via "fdt addr <address>" command. Aborting! ** fs_devread read error - block Failed to mount ext2 filesystem... Can't set block device ** fs_devread read error - block Failed to mount ext2 filesystem... ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 19116182 Bytes = 18.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree SCRIPT FAILED: continuing... ** No partition table - mmc 0 ** Couldn't find partition mmc 0:1 ** No partition table - mmc 0 ** Couldn't find partition mmc 0:1 ** No partition table - mmc 0 ** Couldn't find partition mmc 0:1 No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image ** No partition table - mmc 0 ** Couldn't find partition mmc 0:1 switch to partitions #0, OK mmc1(part 0) is current device ** No partition table - mmc 1 ** Couldn't find partition mmc 1:1 MMC Device 2 not found no mmc device at slot 2 starting USB... Bus usb@ff500000: Register 3000140 NbrPorts 3 Starting the controller USB XHCI 1.10 scanning bus usb@ff500000 for devices... 3 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Device 0: unknown device Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.0.156 (12 ms) *** ERROR: `serverip' not set Cannot autoload with TFTPGET missing environment variable: pxeuuid Retrieving file: pxelinux.cfg/01-ba-df-83-51-8d-a0 Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C0A8009C Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C0A8009 Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C0A800 Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C0A80 Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C0A8 Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C0A Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C0 Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/C Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/default-arm-meson-u200 Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/default-arm-meson Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/default-arm Speed: 100, full duplex *** ERROR: `serverip' not set Retrieving file: pxelinux.cfg/default Speed: 100, full duplex *** ERROR: `serverip' not set Config file not found Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.0.156 (2 ms) *** ERROR: `serverip' not set Cannot autoload with TFTPGET Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.0.156 (2 ms) *** ERROR: `serverip' not set Cannot autoload with TFTPGET 0 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.