Armbian for H313 X96-Q LPDDR3 TV-Box

[Ducdanh Nguyen]

i have a allwinner h313 mxq pro 4k 5g, kinda new ig but does anyone have a image than boot and install through microsd card /w adapter

(microsd card model : sdhc 16gb)

[ARx8]

 Hi, @Nick A .I used the repository at https://github.com/armbian/build/to compile (./compile.sh build BOARD=x96q BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=yes KERNEL_CONFIGURE=no RELEASE=bookworm) the image. Except for WiFi and Bluetooth not working properly, everything else runs fine on the SD card. When using ddbr to back up the Android system, it freezes after a few seconds. Using armbian-install also causes it to freeze, and afterward, I can't boot into the Android system anymore. Below is my device's dts.

dtb dtb.0 dtb.0.dts dtb.0.dts.yaml

Edited yesterday at 02:04 AM by ARx8

[Nick A]

@Randlin there’s a patch for hard coded 1.5 ram detection in the official armbian build. 
 

https://github.com/armbian/build/blob/main/patch/u-boot/v2025-sunxi/0009-sunxi-h616-dram-support-1.5GB-RAM-size.patch
 

 

[ARx8]

14 hours ago, ARx8 said:

Hi, @Nick A .I used the repository at https://github.com/armbian/build/to compile (./compile.sh build BOARD=x96q BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=yes KERNEL_CONFIGURE=no RELEASE=bookworm) the image. Except for WiFi and Bluetooth not working properly, everything else runs fine on the SD card. When using ddbr to back up the Android system, it freezes after a few seconds. Using armbian-install also causes it to freeze, and afterward, I can't boot into the Android system anymore. Below is my device's dts.
你好，@Nick A。我使用了 https://github.com/armbian/build 的仓库来编译（./compile.sh build BOARD=x96q BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=yes KERNEL_CONFIGURE=no RELEASE=bookworm）镜像。除了 WiFi 和蓝牙无法正常工作外，其他功能在 SD 卡上运行一切正常。使用 ddbr 备份 Android 系统时，几秒后会卡住。使用 armbian-install 也会导致卡住，之后就无法再进入 Android 系统了。以下是我的设备的 dts 文件。

dtb dtb.0 dtb.0.dts dtb.0.dts.yaml

Edited 3 hours ago by ARx8  编辑于 ARx8

@Nick A Thank you

[Nick A]

@ARx8 can you take a picture of your board so we can figure out if your wifi chip has mainline kernel drivers. 
 

You can find the gpio #’s using your dts.0.dts file. 

The wifi might already be detected but you are missing firmware. If you can post your dmesg.
 

 

Edited 18 hours ago by Nick A

[jdie]

Hello, I have x96q2 H313 2/16 board v4.0 ram k4b2g0446c hyh9 and apx305. I tried all img, and no one worked on my TV box. Mb u can help me, how I can build img for my board? I need sd card version armbian or arch Linux (not emmc installation)

Edited 1 hour ago by jdie

[ARx8]

8 hours ago, Nick A said:

@ARx8 can you take a picture of your board so we can figure out if your wifi chip has mainline kernel drivers. 
 

You can find the gpio #’s using your dts.0.dts file. 

The wifi might already be detected but you are missing firmware. If you can post your dmesg.

@rafaeldavid My device appears to have the same problem as yours. What was your fix?
@Nick AThanks!  The chips on the motherboard include H313, AXP313A, KMQN10006B-B318, and EA6521QF (Wi-Fi + BT chip).
I have the Linux driver package for this Wi-Fi chip. this Wi-Fi chip (EA6521QF) likely isn't supported by mainline Linux kernel.I’ll figure out how to integrate it later when I need to use Wi-Fi.

Using Wi-Fi is not the most important thing; the key is that I want to install it into the eMMC instead of booting from the SD card. May I ask what modifications I need to make to the original Armbian project code based on the dts I provided to ensure stable read/write operations on the eMMC without crashes?
Moreover, I've already tried using a different TF card. These same cards work fine when installing to eMMC on my other X96Q (DDR v5.1), but they keep freezing up on this device.。

dmesg.txt

Edited 9 hours ago by ARx8
add dmesg