mxq pro 4k 5g allwinner h313 can't sd card boot

[Ducdanh Nguyen]

Hello @Nick A i did everything git cloned now im in setup,

heres what i choosed:

1. Do not change kernel configuration

And after that, i don't found any compactible for my h313

also note that mine firmware is based off d9 Pro 5g so i think it could use the same dram settings and wifi chip except for the cpu. Hope this helps!

[Ducdanh Nguyen]

I have identified the ram chip and nand, but don't know where wifi is, i think thats not very important since i have alot of usb wifi and ethernet

 

[Ducdanh Nguyen]

@Nick A heres the complete info : 

🧠 DRAM

Chip 1:

Marking: MPF694C4G-P

Maker: UniIC (UnilC)

Type: DDR3/DDR3L

Density: 4 Gb (512 MB)

Date code: 2021 (week 11)

Chip 2:

Marking: SBC13H4G150

Maker: UniIC (UnilC)

Type: DDR3/DDR3L

Density: 4 Gb (512 MB)

Date code: 2020 (week 11)

✅ Total RAM = 1 GB (2 × 512 MB)

💾 Storage (eMMC)

Chip:

Marking (line 1): NCEMAM60-08G

Maker: FORESEE

Type: eMMC Flash (not raw NAND)

Capacity: 8 GB

Marking (line 2): 000

Serial/Batch: Z1S1801147073

Date code: 1802 → Year 2018, Week 02

✅ Total storage = 8 GB eMMC (manufactured early 2018)

[Nick A]

@Ducdanh Nguyen you forgot these steps 

choose "Show CSC/WIP/EOS/TVB"

choose "I understand and agree"
 

you should see a few x96q in the list.

[Ducdanh Nguyen]

@Nick A thank you.

[Ducdanh Nguyen]

hey @Nick A, i think i found the serial port

look at the yellow mark on the image

[Nick A]

@Ducdanh Nguyen on the other side of the board it has two capacitors. I don’t think that’s it.

[Ducdanh Nguyen]

@Nick A Oh..

 

[Ducdanh Nguyen]

by the way i don't see any options with allwinner h313 and 1gb ram, can i just choose the 2gb x96q?

[Ducdanh Nguyen]

@Nick A i choosed x96q-lpddr3 (csc) Allwinner H313 TVB with 2gigs of ram and emmc (my box uses emmc)

debian 11

image with desktop enviroment

Edited 2 hours ago by Ducdanh Nguyen

[Ducdanh Nguyen]

@Nick A 

full log (failed):

[💲|🌱] Starting main configuration
[💲|🌱] Using REVISION from [ main VERSION file: '25.05.0-trunk' ]
[💲|🌿] Enabling extension [ armbian-config ]
[💲|🌱] Sourcing family configuration [ /home/nguye/build/config/sources/families/sun50iw9.conf ]
[💲|🌿] Enabling extension [ sunxi-tools ]
[💲|✅] change-tracking: after sourcing family config [ KERNEL_MAJOR_MINOR='6.12' ]
[💲|✅] change-tracking: after sourcing family config [ KERNELBRANCH='tag:v6.12.11' ]
[💲|✅] change-tracking: after sourcing family config [ LINUXFAMILY='sunxi64'  # (was: 'sun50iw9') ]
[💲|✅] change-tracking: after sourcing family config [ KERNELPATCHDIR='archive/warpme-6.12' ]
[💲|✅] change-tracking: after sourcing family config [ BOOTBRANCH='tag:v2025.01' ]
[💲|✅] change-tracking: after sourcing family config [ BOOTPATCHDIR='u-boot-h616' ]
[💲|✅] change-tracking: after sourcing family config [ ATFBRANCH='tag:lts-v2.10.14' ]
[💲|✅] change-tracking: after sourcing family config [ NETWORKING_STACK='network-manager' ]
[💲|🌱] Sourcing arch configuration [ arm64.conf ]
[💲|✅] change-tracking: after sourcing arm64 arch [ ATFDIR='arm-trusted-firmware' ]
[💲|🌱] Using NETWORKING_STACK [ NETWORKING_STACK: network-manager ]
[💲|🌱] Adding networking extensions [ net-network-manager, net-chrony ]
[💲|🌿] Enabling extension [ net-network-manager ]
[💲|🌿] Enabling extension [ net-chrony ]
[💲|🌱] Extension manager [ processed 17 Extension Methods calls and 27 Extension Method implementations ]
[💲|🌱] x96q-lpddr3 [ Using allwinner/sun50i-h313-x96-q-lpddr3.dtb for edge ]
[💲|💥] Error  1 occurred in SUBSHELL [ SUBSHELL at /home/nguye/build/lib/functions/configuration/config-desktop.sh:48 ]
[💲|💥] Cleaning up [ please wait for cleanups to finish ]
[💲|🌿] ANSI log file built; inspect it by running: [ less -RS output/logs/log-build-5e1956f5-4bb3-4cdf-b026-7bcfa7d1794e.log.ans ]
[💲|🌱] Share log manually: [ use one of the commands below (or add SHARE_LOG=yes next time!) ]
[💲|🌿] Share log manually: [ curl --data-binary @output/logs/log-build-5e1956f5-4bb3-4cdf-b026-7bcfa7d1794e.log.ans https://paste.armbian.com/log ]
[💲|🌿] Share log manually: [ curl --data-binary @output/logs/log-build-5e1956f5-4bb3-4cdf-b026-7bcfa7d1794e.log.ans https://paste.armbian.de/log ]
[💲|🌿] Share log manually: [ curl --data-binary @output/logs/log-build-5e1956f5-4bb3-4cdf-b026-7bcfa7d1794e.log.ans https://paste.next.armbian.com/log ]
[💲|🌿] Share log manually: [ curl --data-binary @output/logs/log-build-5e1956f5-4bb3-4cdf-b026-7bcfa7d1794e.log.ans https://paste.armbian.eu/log ]
nguye@DESKTOP-IFEAUMD:~/build$

 

EDIT: it continued while i tried Debian 12

 

Next i choosed

xfce

config_base (onlyone)

internet

Edited 2 hours ago by Ducdanh Nguyen

[Ducdanh Nguyen]

@Nick A success build

log : https://paste.armbian.eu/simirepihe

Edited 27 minutes ago by Ducdanh Nguyen