Rockpi4B reboot loop - seems homeassistant and Zigbee2mqtt and USB related

[Mossieur Oeuf]

Hi, I used to run a full docker environment using the Radxa Debian buster image upgraded to bullseye. Lately as the backport repo has been archived I decided to move onto Armbian as upgrading bullseye to bookworm did not boot (or seemed so...).

After flashing the latest Rockpi4 image to the Rockpi4, I copied the docker configuration and files backups.

I now have a akward behavior:

- starting all the stacks (or containers) works fine, all seems ok

- rebooting via 

sudo reboot

provokes an endless reboot cycle which is only ended if I unplug the USB Zigbee coordinator key. Once the loop is stopped, the RockPi does not have any IPv4 address (only IPv6) and is unreacheable by SSH.

- power cycling with the USB key unplugged fixes the boot loop and everything is back to "normal", except the following dmseg errors:

rock@rockpi4b:~$ sudo dmesg -l 0,1,2,3
[    3.099273] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[    3.099333] rockchip-pcie f8000000.pcie: probe with driver rockchip-pcie failed with error -110
[   11.200510] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43456-sdio for chip BCM4345/9
[   11.731680] brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
[   11.732234] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/9 wl0: Jun 16 2017 12:38:26 version 7.45.96.2 (66c4e21@sh-git) (r) FWID 01-1813af84
[   99.980012] cpu cpu4: _set_opp_voltage: failed to set voltage (825000 825000 1250000 mV): -6
[   99.980072] cpu cpu4: Failed to set regulator voltages: -6
[   99.980097] cpufreq: __target_index: Failed to change cpu frequency: -6
[  246.811985] cpu cpu4: _set_opp_voltage: failed to set voltage (825000 825000 1250000 mV): -6
[  246.812046] cpu cpu4: Failed to set regulator voltages: -6
[  246.812070] cpufreq: __target_index: Failed to change cpu frequency: -6
[  400.087329] cpu cpu4: _set_opp_voltage: failed to set voltage (825000 825000 1250000 mV): -6
[  400.087387] cpu cpu4: Failed to set regulator voltages: -6
[  400.087410] cpufreq: __target_index: Failed to change cpu frequency: -6

Now this is where it gets strange: if I prevent zigbee2mqtt container to automatically start at boot (which cannot be a permanent solution obviously) it doesn't matter if the USB key is plugged in or not (whichever usb port), Armbian boots ok and all other containers start ok.

 

I already checked the /dev/ttyusb0 access rights, tried to change the docker container user, activate the rockchipdw3 overlay, changing the USB port for the Zigbee key, switching from rolling to stable and vice versa, to no avail.

No need to say that the same config worked under bullseye.

 

Does someone have any lead or clue about what's happening ? Where can I look as logs don't show anything special...

Any help would be greatly appreciated, thanks in advance!

 

My config:

Rockpi4B, Armbian_community_25.11.0-trunk.70_Rockpi-4b_bookworm_current_6.12.43_minimal.img, usb-ITead_Sonoff_Zigbee_3.0_USB_Dongle_Plus