ron123456 Posted December 10, 2018 Posted December 10, 2018 Hi I trying to create an Access Point from NanoPi M1 plus device having Ubuntu_bionic_next_4.14.78.7z OS. I am able to create the AP and my devices are able to connect to it. But somehow they are not able to use the internet. I have eth0 interface as plugged in to the board which whose IP will be forwarded. via wlan0 interface. I have already set net.ipv4.ip_forward=1 in /etc/sysctl.conf and /proc/sys/net/ipv4/ip_forward to 1. I issued the following iptables commands, but it didn't work... sudo iptables -F sudo iptables -t nat -F sudo iptables -t nat -A POSTROUTING -o wlan0 -j MASQUERADE sudo iptables -A FORWARD -i wlan0 -o eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT sudo iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.55.247 netmask 255.255.255.0 broadcast 192.168.55.255 inet6 fe80::81:14ff:fea2:1b15 prefixlen 64 scopeid 0x20<link> ether 02:81:14:a2:1b:15 txqueuelen 1000 (Ethernet) RX packets 599 bytes 40641 (40.6 KB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 59 bytes 9337 (9.3 KB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 39 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 571 bytes 41372 (41.3 KB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 571 bytes 41372 (41.3 KB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 172.24.1.1 netmask 255.255.255.0 broadcast 172.24.1.255 ether b0:f1:ec:2c:dd:0c txqueuelen 1000 (Ethernet) RX packets 32 bytes 2796 (2.7 KB) RX errors 0 dropped 1 overruns 0 frame 0 TX packets 18 bytes 2316 (2.3 KB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 02:81:14:a2:1b:15 brd ff:ff:ff:ff:ff:ff inet 192.168.55.247/24 brd 192.168.55.255 scope global eth0 valid_lft forever preferred_lft forever inet6 fe80::81:14ff:fea2:1b15/64 scope link valid_lft forever preferred_lft forever 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000 link/ether b0:f1:ec:2c:dd:0c brd ff:ff:ff:ff:ff:ff inet 172.24.1.1/24 brd 172.24.1.255 scope global wlan0 valid_lft forever preferred_lft forever I dont know, where I am wrong?
Recommended Posts