jps

Or this one: https://www.raspberrypi-spy.co.uk/2018/11/raspberry-pi-7-segment-led-display-module-using-python/ orangepi@orangepiplus2e:~/Adafruit_Python_LED_Backpack$ sudo python3 7segment_counter.py Traceback (most recent call last): File "7segment_counter.py", line 32, in <module> display.begin() File "/home/orangepi/Adafruit_Python_LED_Backpack/Adafruit_LED_Backpack/HT16K33.py", line 53, in begin self._device.writeList(HT16K33_SYSTEM_SETUP | HT16K33_OSCILLATOR, []) File "/usr/local/lib/python3.6/dist-packages/Adafruit_GPIO-1.0.4-py3.6.egg/Adafruit_GPIO/I2C.py", line 129, in writeList File "/home/orangepi/.local/lib/python3.6/site-packages/Adafruit_PureIO/smbus.py", line 364, in write_i2c_block_data self._device.write(data) OSError: [Errno 6] No such device or address And this one based on SMBus that i installed previously: https://github.com/emcconville/HT16K33 sudo python3 clo.py !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ! Unable to load SMBus ! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ! Switching to terminal emulation ! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Traceback (most recent call last): File "clock.py", line 9, in <module> from _HT16K33 import FourDigit ImportError: cannot import name 'FourDigit' But does not work either.

I tried this one based on micropython but when i install trought pip returns many errors: sudo -H pip3 install adafruit-circuitpython-ht16k33 ... error: invalid command 'bdist_wheel' ---------------------------------------- Failed building wheel for Adafruit-Blinka Running setup.py clean for Adafruit-Blinka Running setup.py bdist_wheel for adafruit-circuitpython-busdevice ... error ... error: invalid command 'bdist_wheel' ---------------------------------------- Failed building wheel for adafruit-circuitpython-busdevice ... And many more. Also it needs busio and board but can't find it. Also i installed adafruit-blinka alone (https://pypi.org/project/Adafruit-Blinka/) what have busio and board drivers, but it doesn't work either. The instalations is success, but after that the code can't find busio or board: sudo -H pip3 install adafruit-blinka Requirement already satisfied: adafruit-blinka in /usr/local/lib/python3.6/dist-packages Requirement already satisfied: Adafruit-PlatformDetect>=2.11.1 in /usr/local/lib/python3.6/dist-packages (from adafruit-blinka) Requirement already satisfied: Adafruit-PureIO>=1.1.5 in /usr/local/lib/python3.6/dist-packages (from adafruit-blinka) Requirement already satisfied: pyftdi>=0.40.0 in /usr/local/lib/python3.6/dist-packages (from adafruit-blinka) Requirement already satisfied: sysv_ipc in /usr/local/lib/python3.6/dist-packages (from adafruit-blinka) Requirement already satisfied: pyusb>=1.0.0 in /usr/local/lib/python3.6/dist-packages (from pyftdi>=0.40.0->adafruit-blinka) Requirement already satisfied: pyserial>=3.0 in /usr/local/lib/python3.6/dist-packages (from pyftdi>=0.40.0->adafruit-blinka) orangepi@orangepiplus2e:~$python3 -m pip install -U --user pip gpiod Collecting pip Downloading https://files.pythonhosted.org/packages/43/84/23ed6a1796480a6f1a2d38f2802901d078266bda38388954d01d3f2e821d/pip-20.1.1-py2.py3-none-any.whl (1.5MB) 100% |████████████████████████████████| 1.5MB 185kB/s Collecting gpiod Downloading https://files.pythonhosted.org/packages/8e/9c/3818182fa32fd5db2a42be9c340d3d6accf8c256befc741c0a59d61d582c/gpiod-1.2.5.tar.gz Building wheels for collected packages: gpiod Running setup.py bdist_wheel for gpiod ... error Complete output from command /usr/bin/python3 -u -c "import setuptools, tokenize;__file__='/tmp/pip-build-kdvfombf/gpiod/setup.py';f=getattr(tokenize, 'open', open)(__file__);code=f.read().replace('\r\n', '\n');f.close();exec(compile(code, __file__, 'exec'))" bdist_wheel -d /tmp/tmpkfkkyv80pip-wheel- --python-tag cp36: usage: -c [global_opts] cmd1 [cmd1_opts] [cmd2 [cmd2_opts] ...] or: -c --help [cmd1 cmd2 ...] or: -c --help-commands or: -c cmd --help error: invalid command 'bdist_wheel' ---------------------------------------- Failed building wheel for gpiod Running setup.py clean for gpiod Failed to build gpiod Installing collected packages: pip, gpiod Running setup.py install for gpiod ... done Successfully installed gpiod-1.2.5 pip-20.1.1 orangepi@orangepiplus2e:~$ sudo python3 ddd.py Traceback (most recent call last): File "ddd.py", line 9, in <module> import board File "/home/orangepi/.local/lib/python3.6/site-packages/board.py", line 93, in <module> from adafruit_blinka.board.orangepi.orangepipc import * File "/home/orangepi/.local/lib/python3.6/site-packages/adafruit_blinka/board/orangepi/orangepipc.py", line 3, in <module> from adafruit_blinka.microcontroller.allwinner.h3 import pin File "/home/orangepi/.local/lib/python3.6/site-packages/adafruit_blinka/microcontroller/allwinner/h3/pin.py", line 4, in <module> PA0 = Pin(0) File "/home/orangepi/.local/lib/python3.6/site-packages/adafruit_blinka/microcontroller/generic_linux/libgpiod_pin.py", line 34, in __init__ self._chip = gpiod.Chip("gpiochip0", gpiod.Chip.OPEN_BY_NAME) AttributeError: module 'gpiod' has no attribute 'Chip' I think i tried everithing... I don't know where to go.... Thank you for your response.

Is it even possible to run the 7-segment HT16K33 module with Armbian and Orange Pi? I'm trying with I2C and SMBus2 but can not make it work. I can see the module, but it is imposible to communicate with it: sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: 70 -- -- -- -- -- -- -- Any help will be apreciated. Thank you in advance.

Hi. First at all, thank you for this. Orange Pi +2e + Armbian Debian GNU/Linux 10. When i run demo i have this error: Unrecognized board type, aborting... Problem initializing ArmbianIO library Pins connected to +5Vcc, pins 3 (SDA) y 5 (SCL). What i'm doing wrong? Thanks in advance.

Hello. I am trying to work with a 7-Segment LED Display Module (HT16K33) in a Orange Pi +2e, but I don't know how to start... Any iddea? Thank you in advance.

Maybe you need a resistor in your circuit?

wow. I just realized that the CPU temperature in armbianmonitor is the same that the one i have reading the DS18B20 sonda .... What is going on??

And, what about the strange readings in thermal_zones. My cpu give me 22.6ºC with armbianmonitor, but reading directly in any of the thermal zones with cat i have readings like '40898'. What has changed from previous versions? Than you in advance.

Yes. Thank you martinayotte. If sombody needs that, i just have to add this lines to '/boot/armbianEnv.txt' overlays=w1-gpio param_w1_pin=PA20 param_w1_pin_int_pullup=1 and works like a charm! Thank you very much.

Hi. Recently i upgraded to Armbian_5.65_Orangepilite_Debian_stretch_next_4.14.78 and i have two problems. I can not read the thermal zones properly with neither of those: cat /sys/class/thermal/thermal_zone0/temp cat /sys/devices/virtual/thermal/thermal_zone0/temp cat /etc/armbianmonitor/datasources/soctemp because i have results like "30371". But when the system starts the correct temperature is displayed: Welcome to ARMBIAN 5.73 stable Debian GNU/Linux 9 (stretch) 4.19.20-sunxi System load: 0.07 0.15 0.10 Up time: 10 min Memory usage: 29 % of 493MB IP: 192.168.1.46 CPU temp: 33°C Usage of /: 10% of 15G and with armbianmonitor too: Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 17:39:34: 1200MHz 0.06 3% 1% 1% 0% 0% 0% 34.6°C 0/15 17:39:39: 480MHz 0.06 1% 0% 0% 0% 0% 0% 31.5°C 0/15 17:39:45: 480MHz 0.13 4% 3% 0% 0% 0% 0% 31.8°C 0/15 My second problem is that my DS18B20 sonda does not work anymore. In /etc/modules-load.d/modules.conf i have: w1-sunxi w1-gpio w1-therm but there is nothing in /sys/bus/w1/devices/ is there any changes in this new version? I check the forum but i does not found anything. Any iddeas? Thanks in advance.

Thanks Ucino, i arrived till there. In my first post i wrote: so, i need to read much more about how to compile a driver in a live Armbian distribution. Thank you anyway.

But... I still have the doubt that what to do with the content of https://github.com/avafinger/gc2035........... I mean ... i don't know how to build a module. Anyway, all it's working, so thanks.

Yes, 3.X kernel have the drivers. Works fine. Thank you. But... but I still have the doubt that what to do with the content of https://github.com/avafinger/gc2035. Thank again.

Sure. Orange Pi Lite + CSI camera orange Pi native (Shenzhen Xunlong Software CO.,Limited) camera, and last Armbian for Lite Armbian_5.59_Orangepilite_Ubuntu_bionic_next_4.14.65. Thank you very much

Excuse my clumsiness, but I don't know what to do with the files in https://github.com/avafinger/gc2035 i can not find the paths related in this link.... i can not make the camera work in last Armbian. Thanks any help...