I'm using an Orange Pi 5 Plus 16GB SBC, with Armbian image (https://dl.armbian.com/orangepi5-plus/Bookworm_current_cinnamon-backported-mesa) which uses Kernel 6.12. I am trying to get a BME280 I2C sensor attached to the following pins of the 40 pins; 1 (3.3v), 3 (GPIO0C0), 5 (GPIO0B7), and 6 (GND). The BME280 sensor has the VIN wired to 3.3v (pin 1), SDA wired to SDA (pin 3), SCL wired to SCL (pin 5), and GND to GND (pin 6). The device should use address 0x76, but isn't listed under the four I2C buses found in /dev. This configuration worked fine when using the stock OrangePi 5 Plus Debian Bookworm image, but does not have I2C2 listed as a device under /dev under Armbian image listed above. My armbianEnv.txt is: verbosity=1 bootlogo=true console=both overlay_prefix=rockchip-rk3588 fdtfile=rockchip/rk3588-orangepi-5-plus.dtb rootdev=UUID=3cbd3c35-190b-4cc5-8db3-4334fa84ccbd rootfstype=ext4 overlays=rockchip-rk3588-i2c8-m2 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u I have attached 4 images (screenshots) with the following captions i2c.png - List of I2C buses and addresses (Armbian Image) i2c_2.png - List of DTBs (Armbian Image) i2c_3.png - List of DTBOs aka overlays (Armbian Image) i2c_opi2.png - List of I2C buses and addresses of I2C2 (Orange Pi Debian 12 Image) Why isn't I2C2 found in /dev of Armbian image?

Thanks for the feedback. Here are the logs: 4gb machine | https://paste.armbian.de/seciliriqi 2gb machine | https://paste.armbian.de/tikazukifo

Hello, I'm new to Armbian and SoC/ARM devices but I've installed Armbian on the device before, however after tinkering around with RKDevTool and installing FriendlyELEC images on it through USB I'm now unable to boot from SD Card. I've done the "EraseAll" procedure under unbricking method https://wiki.friendlyelec.com/wiki/index.php/CM3588#Windows_Users however it didn't help. I've tried two SD Cards and I have no idea what else I can do. Unfortunately I wasn't able to find anything useful on google. The error is: "Gave up waiting for root file system device." "ALERT! UUID=602525b7-ed9f-43f7-91b0-1dc4e67b44bf does not exist. Dropping to a shell!" When in the initramfs shell I checked blkid and it seems like the SD card is /dev/mmcblk1 PTUUID="8cdc55ae-c576-6f4c-a793-0397a48dccf0". I'm guessing it should work if I change the armbian UUID or is that assumption incorrect? If so how should I go about it? Also it looks like the UUID Armbian is looking for is static which surprised me... I thought it's something randomly generated by the system. I fixed it edit: I booted into debian I got from FriendlyELEC and wrote the Armbian image directly with DD to the SD card and now it works. Before I was writing with Balena Etcher and USB Writer on Windows, tried multiple times, formatted the sd card with diskpart etc., no idea why it didn't work with those but worked with DD, especially since I did it with etcher before and it was ok. I was on a different windows version but I doubt that's the issue?

Hey, sorry for late response Here are the images https://alist.genshin.gay/rk3229 Also, I did solder an sd slot but it seems to be boot looping (the flash drive flickering). That's just my guess

Hello! Few days I try to config small printserver with rk3239 box. It use "v24.11.1 for rk322x-box running Armbian Linux 6.6.63-current-rockchip" image (tested with older images too). Looks everething works fine. But one problem with printing app. I try to use hplip-printer-app as snap pkg. https://github.com/OpenPrinting/hplip-printer-app App start, but if try to connect to http://IP:8000 it crash with "Segmentation fault" I thought maybe some app bug, but I had make some tests with amlogic S905X, S905X3 boxes and raspi 4b. There apps works fine. I not understand why rk box crashes?