Jump to content

Proddik

Members
  • Posts

    3
  • Joined

  • Last visited

Everything posted by Proddik

  1. I have banana pi m2+ with ampak AP6212. Install Armbian 5.75 with Linux kernel 4.19.20 Driver on wi-fi brcmfmac. Wi-Fi access point actived via armbian-config. ifconfig: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.20 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::81:fcff:fe71:785b prefixlen 64 scopeid 0x20<link> ether 02:81:fc:71:78:5b txqueuelen 1000 (Ethernet) RX packets 76186 bytes 46503714 (46.5 MB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 12755 bytes 2691167 (2.6 MB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 38 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 1954 bytes 587743 (587.7 KB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 1954 bytes 587743 (587.7 KB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 172.24.1.1 netmask 255.255.255.0 broadcast 172.24.1.255 inet6 fe80::12d0:7aff:fe79:194f prefixlen 64 scopeid 0x20<link> ether 10:d0:7a:79:19:4f txqueuelen 1000 (Ethernet) RX packets 12676 bytes 2511391 (2.5 MB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 37290 bytes 44389268 (44.3 MB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 iwconfig wlan0: wlan0 IEEE 802.11 Mode:Master Tx-Power=31 dBm Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Working good, but on smartphone disabled Internet working after 2-5 minutes(sometime 20-30 minites). Wi-fi Connection working on smartphone andnot disconnected, but Internet was gone and ping failed smartphone. From BPI arping working...ping failed. Try set skip_inactivity_poll=1 in hostapd.conf - still Internet disconnecting. What's problem...maybe in driver brcmfmac not stable?!
  2. I have orange pi one zero. I buy extended Nas card for orange pi zero. After install extended board, i can't logging in system. Root or user password not accept system) Try logging with UART and SSH. Try copy new password in shadow on my PC. But system not accept any password. Maybe system himself change password after changing system or some problem with bash? p.s. I have Bpi M2p too and last month was the same situation. But console not accepted any login and after enter "root"....again asked to enter login. I rewrite new Armbian and return to work.
  3. I got Sunvell R69 form China yesterday with 1+8Gb configuration and blue PCB version is 2.0. After disassmbling I interesting whats interface(not soldering) on back side with SD card slot and USB.If I understand it's not soldering CSI connector for camera? Right?
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines