• Content Count

  • Joined

  • Last visited

Everything posted by lukaszertel

  1. Thank You Frank, I will check it at friday. At the moment I don't have access to my Orange Pi. And of couse I will write down my results. Cheers! ================= --------Edited-------- ================= It works! I only commented out humidity parameters - rest is as You suggested. Thank You once again for help FRANK333 :-) One additional question: I messed up a little bit with setting correct time on my Orange Pi Zero. I changed it and now it's correct, but not on stats graph. On browser tab with Statist
  2. Working like a charm :-) root@orangepizero:/etc/rpimonitor# cat /sys/bus/w1/devices/28-020b92459bc7/w1_slave 6a 01 55 05 7f 7e 81 66 1d : crc=1d YES 6a 01 55 05 7f 7e 81 66 1d t=22625 I've lastest available version of RPi-Monitor on my Orange Pi Zero: Version: 2.12-r0 by Xavier Berger I tested both values: t.(d+)$ and t=(d+)$ Those values are used in conf file, in my case custo.conf witch is mentioned in main config file /etc/rpimonitor/data.conf Of course, after each change I restart service with command: service rpimonitor restart ======
  3. Dear Armbian friends, I have question about add DS18B20 temp sensor at RPi-Monitor (web based interface). Can somebody paste working config of this sensor? On internet I found many tutorials but with DHT sensors. On this page (Xavier is an author of RPi-Monitor I think) is described DS18B20 but in status "Working in progress". I tried this but without luck. Cheers, Lucas
  4. I'm back :-) Well, it's working! Almost.. When I checking temperature not evey response is proper, some anwers are with "crc=c9 NO". I have checked wiring and connections on board few times, changed resistor and cables. Do you have any idea? root@orangepizero:~# cat /sys/bus/w1/devices/28-020b92459bc7/w1_slave ff ff ff ff ff ff ff ff ff : crc=c9 NO 00 00 00 00 00 00 00 00 00 t=-62 root@orangepizero:~# cat /sys/bus/w1/devices/28-020b92459bc7/w1_slave 57 01 55 05 7f 7e 81 66 9d : crc=9d YES 57 01 55 05 7f 7e 81 66 9d t=21437 root@orangepizero:~# cat /sys/bus/w1/devices/2
  5. New sensor (DS18B20) is in delivery, I expect tomorrow I should get it. Cheers!
  6. Thank you for taking your time on tests My cpufreg now looks like root@orangepizero:~# more /etc/default/cpufrequtils # WARNING: this file will be replaced on board support package (linux-root-...) upgrade ENABLE=true MIN_SPEED=480000 #MIN_SPEED=240000 MAX_SPEED=1200000 #GOVERNOR=ondemand GOVERNOR=interactive But nothing is discovered. I hope that new sensor will come soon! Stay tuned ;-)
  7. A moment ago I have ordered DS18B20. Hope it will do the job. When you mention about this model I found that this guy also used it. When DS18B20 arrive I will write if it helps. Cheers!
  8. I have three samples of DHT11, one of them is equipped with diode but it seems that this model isn't compatible. I will order DS18B20. Can someone confirm which temperature sensor is working on Orange Pi Zero (with H2+)?
  9. Checked. On 20k scale is 4.68 so it looks like 4k7. I also tried another sample of resistor to be sure that this is not the case. No changes.
  10. Thank you for answer. I have switched between kernels (installed bionic image): 4.14.70 4.14.84 4.18.8 Nothing changed. Seems that it's dead end - it's not a kernel issue. Any other ideas?
  11. Dear Armbian Friends, My temperature sensor is not detected by board. Can somebody give me some advice what should I chceck / change / test now? Cheers! Lucas I tried: - another sample of DHT11 - changed cables to different ones - changed - both tested sensors were connected with 4.7k resistor between positive and data cable - tried different system versions like bionic, stretch and now jessie - tried to load modules via /etc/modules-load.d/modules.conf g_serial w1-sunxi w1-gpio w1-therm - or with /boot/armbia