Gabriel

Members
  • Content Count

    1
  • Joined

  • Last visited

  1. Hi everyone, My name is Gabriel and I am a new person in the community. After installing ARMBIAN (Armbian_5.91_Clearfogbase_Debian_stretch_default_4.14.135) with the Mini PCI Express Marvel 88SE9215, I got a problem with my Clearfog Pro-A1 revision-2.1. It did not work properly like 88SE9215 did not show me my disks. My Idea is to deploy my NAS server with OMV. I tried to compile the kernel so many times with different modules like SATA, PATA, and AHCI but it did not work also. I guess that my u-boot is not setup properly because I was reading a couple post about it and it’s working to everyone. Someone can give me a favor pls and tell me your ideas to try to solve that problem Thanks. Logs: Armbianmonitor: http://ix.io/201C root@clearfogbase:~# lspci 00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6828 (rev 0a) 00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6828 (rev 0a) 02:00.0 SATA controller: Marvell Technology Group Ltd. Device 9215 (rev 11) root@clearfogbase:~# lspci -nv 00:02.0 0604: 11ab:6828 (rev 0a) (prog-if 00 [Normal decode]) Flags: fast devsel Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Prefetchable memory behind bridge: 00000000-000fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [100] Advanced Error Reporting 00:03.0 0604: 11ab:6828 (rev 0a) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00010000-00010fff Memory behind bridge: e0000000-e00fffff Prefetchable memory behind bridge: 00000000-000fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [100] Advanced Error Reporting 02:00.0 0106: 1b4b:9215 (rev 11) (prog-if 01 [AHCI 1.0]) Subsystem: 1b4b:9215 Flags: bus master, fast devsel, latency 0, IRQ 53 I/O ports at 10020 I/O ports at 10030 I/O ports at 10028 I/O ports at 10034 I/O ports at 10000 Memory at e0040000 (32-bit, non-prefetchable) Expansion ROM at e0000000 Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Express Legacy Endpoint, MSI 00 Capabilities: [e0] SATA HBA v0.0 Capabilities: [100] Advanced Error Reporting Kernel driver in use: ahci Booting from Clearfog U-Boot SPL 2018.01-02337-gdc4398fdb8 (May 14 2018 - 19:03:16) High speed PHY - Version: 2.0 Detected Device ID 6828 board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 3 | SATA0 | | 1 | 0 | SGMII1 | | 2 | 5 | PCIe1 | | 3 | 5 | USB3 HOST1 | | 4 | 5 | PCIe2 | | 5 | 0 | SGMII2 | -------------------------------- PCIe, Idx 1: detected no link PCIe, Idx 2: detected no link High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.29.0 DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Trying to boot from SPI U-Boot 2018.01-02337-gdc4398fdb8 (May 14 2018 - 19:03:16 +0200), Build: jenkins-u-boot-clearfog-model=pro,variant=spi-10 SoC: MV88F6828-?? (a) at 1600 MHz DRAM: 1 GiB (800 MHz, 32-bit, ECC not enabled) MMC: mv_sdh: 0 SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB Model: SolidRun Clearfog Board: SolidRun ClearFog Pro SCSI: SATA link 0 timeout. AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode Net: eth1: ethernet@70000, eth2: ethernet@30000, eth3: ethernet@34000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0(part 0) is current device ** No partition table - mmc 0 ** starting USB... USB0: Register 2000120 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Device 0: device type unknown ... is now current device ** Bad device usb 0 ** ** Bad device usb 0 ** scanning bus for devices... Found 0 device(s).