flippy

  • Posts

    8
  • Joined

  • Last visited

2 Followers

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

flippy's Achievements

  1. After replacing the bootloader, the iperf3 benchmark can reach gigabit. of course, the dtb provided in the attachment should also be replaced at the same time, please do not use meson-sm1-sei610.dtb or meson-sm1-sei610-ethfix.dtb. I mainly use it for openwrt firmware. As you said, Android does not support booting after replacing the bootloader.
  2. Hi, I hope you can realize these points as soon as possible. These few questions have been bothering me.
  3. No, rtl8822cs currently does not work in armbian. hk1 box has a bcm-43xx module and it works. In dts, the compatible attribute of the wifi module is "brcm,bcm4329-fmac", which supports most Broadcom sdio modules, but rtl8822cs does not provide corresponding drivers in the mainline linux kernel.
  4. I found the correct method to fix the bug that the x96-max-plus(s905x3) gigabit ethernet does not work: Up to now, only HK1Box/vontar x3 is the only s905x3 TV box that can be used perfectly in armbian. So I extracted the bootloader of hk1box and wrote it into x96-max-plus, and it worked. This method is very simple, so it is recommended to everyone in need. Step 1: upload three dtbs into /boot/dtb/amlogic : meson-sm1-x96-max-plus-100m.dtb meson-sm1-x96-max-plus.dtb meson-sm1-hk1box-vontar-x3.dtb (Similar to meson-sm1-x96-max-plus.dtb, only the modal name is changed) Step 2: modify /boot/uEnv.txt, replace dtb with meson-sm1-x96-max-plus-100m.dtb, restart the Armbian system Step 3: upload hk1box-bootloader.img to /tmp Step 4: Run these commands under the shell: dd if=/tmp/hk1box-bootloader.img of=/dev/mmcblk2 bs=1 count=442 dd if=/tmp/hk1box-bootloader.img of=/dev/mmcblk2 bs=512 skip=1 seek=1 sync reboot Step 5: modify /boot/uEnv.txt, replace dtb with meson-sm1-x96-max-plus.dtb, and restart again. meson-sm1-x96-max-plus.dtb meson-sm1-x96-max-plus.dts meson-sm1-hk1box-vontar-x3.dtb meson-sm1-hk1box-vontar-x3.dts hk1box-bootloader.img.xz meson-sm1-x96-max-plus-100m.dtb meson-sm1-x96-max-plus-100m.dts x96maxplus-orig-bootloader.img.xz
  5. I improved the dts of Phicomm N1 again. The reasons are: 1. The Ethernet card of N1 is not very compatible with some switches. When the ethernet phy is activated, the flow control sometimes cannot be turned on, so will get bad results during the speedtest.net . For this reason, I added a dts separately force_thresh_dma_mode, which is equivalent to flow control in software mode. But there are also side effects: tx performance is reduced. In addition, as auxiliary optimization items, set snps, aal; snps, txpbl = <0x8>; snps, rxpbl = <0x4>; their role is to improve the performance of the network card. 2. The phy reset-delay-us value of N1 is sometimes not enough. When running openwrt, sometimes the ethernet phy cannot be enabled, so the reset-delay-us value is increased. Provide two dts files: meson-gxl-s905d-phicomm-n1.dts: This is the default dts, used in most occasions, when the flow control can be turned on normally, this is the best choice meson-gxl-s905d-phicomm-n1-thresh.dts: This is a dts with the force_thresh_dma_mode option enabled. It is applicable when flow control cannot be turned on. You can use force_thresh_dma_mode to control flow at the cost of a small amount of performance loss. meson-gxl-s905d-phicomm-n1.dts meson-gxl-s905d-phicomm-n1-thresh.dts
  6. hi lewis: Yes, i am happy to share it。 The main body of those mirrors is from the ambien community. I just recompiled the kernel on the results of others, using the kernel source code from 150balbes, and added the dtb file for beikeyun, you can use it at will. rk3328-beikeyun-1200mhz.dts rk3328-beikeyun-1296mhz.dts rk3328-beikeyun-1392mhz.dts rk3328-l1pro-1296mhz.dts rk3328-l1pro-1392mhz.dts rk3328-l1pro-1512mhz.dts
  7. In the mainline kernel, meson-gxl-s905d-phicomm-n1.dts has been around for a long time, but there has been a problem of high CPU load. I fixed it and it has been stable for several months, so it is shared for reference . I think the cause of the problem is that the IRQ is wrong. The original value is 29 and needs to be changed to 25. // SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (c) 2018 He Yangxuan */ /dts-v1/; #include "meson-gxl-s905d-p230.dts" / { compatible = "phicomm,n1", "amlogic,s905d", "amlogic,meson-gxl"; model = "Phicomm N1"; cvbs-connector { status = "disabled"; }; leds { compatible = "gpio-leds"; status { label = "n1:white:status"; gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; default-state = "on"; }; }; }; &cvbs_vdac_port { status = "disabled"; }; &external_phy { /delete-property/ reset-gpios; interrupts = <25 IRQ_TYPE_LEVEL_LOW>; };
  8. Hello everyone, this is my first post. I extracted 6 x96-max and x96-max + dts from the Android box, but I do n’t seem to have permission to upload attachments. I do n’t know how to upload? I have one x96-max and one x96-max +, both of which have 4G memory and 64G EMMC. Both WIFI modules are 6222B-SRB, based on RTL8822BS, so they can not work in armbian. In addition, the x96-max + Ethernet uses meson-sm1-sei610.dts for minor modifications. The Ethernet card cannot work at Gigabit, but it can work at 100M. total 1056 -rw-r--r-- 1 root root 77824 Feb 28 22:44 01_dtbdump_Amlogic.dtb -rw-r--r-- 1 root root 88556 Feb 1 21:20 01.dts -rw-r--r-- 1 root root 77824 Feb 28 22:44 02_dtbdump_Amlogic.dtb -rw-r--r-- 1 root root 88838 Feb 1 21:20 02.dts -rw-r--r-- 1 root root 77824 Feb 28 22:44 03_dtbdump_Amlogic.dtb -rw-r--r-- 1 root root 88819 Feb 1 21:20 03.dts -rw-r--r-- 1 root root 88064 Feb 28 22:44 04_dtbdump_Amlogic.dtb -rw-r--r-- 1 root root 100983 Feb 1 21:20 04.dts -rw-r--r-- 1 root root 88064 Feb 28 22:44 05_dtbdump_Amlogic.dtb -rw-r--r-- 1 root root 100983 Feb 1 21:20 05.dts -rw-r--r-- 1 root root 88064 Feb 28 22:44 06_dtbdump_Amlogic.dtb -rw-r--r-- 1 root root 101194 Feb 1 21:20 06.dts lrwxrwxrwx 1 root root 6 Feb 1 21:22 g12a_u212_1g.dts -> 01.dts lrwxrwxrwx 1 root root 6 Feb 1 21:22 g12a_u212_2g.dts -> 02.dts lrwxrwxrwx 1 root root 6 Feb 1 21:22 g12a_u212_4g.dts -> 03.dts lrwxrwxrwx 1 root root 6 Feb 1 21:22 sm1_ac213_1g.dts -> 04.dts lrwxrwxrwx 1 root root 6 Feb 1 21:21 sm1_ac213_2g.dts -> 05.dts lrwxrwxrwx 1 root root 6 Feb 1 21:21 sm1_ac213_4g.dts -> 06.dts aml-s905x3-x96max_and_x96maxplus-dts.tar.gz