1voud

Members
  • Content Count

    3
  • Joined

  • Last visited

About 1voud

  • Rank
    Newbie

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Sorry for wasting your time, it is really that simple. Now running happily on kernel 5.4.20. Thank you for your help!
  2. Thank you for the reply. root@bananapi:/# dmesg |grep tty [ 0.000000] Kernel command line: root=UUID=2a591b9c-5c95-34af-9d1a-a591d0134ad8 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 h1 [ 0.001175] printk: console [tty1] enabled [ 2.868060] printk: console [ttyS0] disabled [ 2.888269] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 49, base_baud = 1500000) is a U6_16550A [ 2.888344] printk: console [ttyS0] enabled [ 2.911471] 1c28c00.serial: ttyS1 at MMIO 0x1c28c00 (irq = 50, base_baud = 1500000) is a U6_16550A [ 2.934678] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 51, base_baud = 1500000) is a U6_16550A [ 11.321905] systemd[1]: Created slice system-getty.slice. root@bananapi:/# cat /proc/device-tree/soc/serial@1c28c00/status okayroot@bananapi:/# I'm using the PG6/PG7 pins.
  3. Hi, I'm using a cubietruck and bananapi board (both A20 devices) for a long time (They run very stable for many years). I'm using uart3 for interfacing with arduino boards using the kernel overlay. When I upgrade the kernel to a version 5+ the overlay does not work anymore and ttyS3 is not working and missing in dmesg. The behaviour is the same on both boards. Autoboot in 1 seconds, press <Space> to stop switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 3708 bytes read in 34 ms (106.4 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 217 bytes read in 26 ms (7.8 KiB/s) 7343156 bytes read in 451 ms (15.5 MiB/s) 7744344 bytes read in 473 ms (15.6 MiB/s) Found mainline kernel configuration 42183 bytes read in 70 ms (587.9 KiB/s) 1078 bytes read in 96 ms (10.7 KiB/s) Applying kernel provided DT overlay sun7i-a20-uart3.dtbo 5845 bytes read in 82 ms (69.3 KiB/s) Applying kernel provided DT fixup script (sun7i-a20-fixup.scr) ## Executing script at 44000000 ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7343092 Bytes = 7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Ramdisk to 498ff000, end 49fffbf4 ... OK reserving fdt memory region: addr=43000000 size=70000 Loading Device Tree to 4988c000, end 498fefff ... OK Starting kernel ... root@bananapi:~# cat /proc/version Linux version 5.4.20-sunxi (root@builder) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #20.02.1 SMP Mon Feb 17 02:09:41 CET 2020 root@bananapi:~# cat /boot/armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=2a591b9c-5c95-34af-9d1a-a591d0134ad8 rootfstype=ext4 overlays=uart3 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u It looks like the overlay is loaded correct. Is there anything wrong in my setup, can I try something to make it work (4.19.104-sunxi is still working fine :) Thank you!