Jump to content

Armbian_User

Members
  • Posts

    5
  • Joined

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. I have this issue on 2 out of 3 cubox-i4x4-300-D models All 3 have WiFi working successfully Here is the output from the working (5.9.14) system: find /sys -name phy_id /sys/devices/platform/soc/2100000.bus/2188000.ethernet/mdio_bus/2188000.ethernet-1/2188000.ethernet-1:00/phy_id find: ‘/sys/module/at803x/drivers’: Input/output error Here is the output from one of the broken (working on 5.7.15) system: find /sys -name phy_id /sys/devices/soc0/soc/2100000.bus/2188000.ethernet/mdio_bus/2188000.ethernet-1/2188000.ethernet-1:04/phy_id find: ‘/sys/module/at803x/drivers’: Input/output error
  2. Hello Igor, Thanks for your response. I've had a chance to try your suggestions. None worked for me. Here is a link to the armbianmonitor from a new, clean install using a fresh download of Armbian_20.08.1_Cubox-i_buster_current_5.8.5.img.xz http://ix.io/2AvJ and another after apt-get update && apt-get upgrade -y http://ix.io/2AvL Just to clarify, all my cubox-i's are the cubox-14x4 variant and all exhibit this issue. Do you have any further suggestions I could try? Thanks
  3. Upgrading cubox-i Armbian Buster from kernel 5.7.x to Kernel 5.8.y breaks ethernet and I'm unable to get it connected again. Works fine again downgrading back to 5.7.y. This occurs on multiple cubox-i devices. System diagnosis information will now be uploaded to http://ix.io/2zH6 dmesg | grep eth0 [ 4.667327] fec 2188000.ethernet eth0: registered PHC device 0 [ 22.369472] fec 2188000.ethernet eth0: Unable to connect to phy nlcli wlan0: connected to sketch-wlan "Broadcom BCM4330" wifi (brcmfmac), 6C:AD:F8:1D:36:25, hw, mtu 1500 ip4 default inet4 10.1.0.41/22 route4 0.0.0.0/0 route4 10.1.0.0/22 route4 169.254.0.0/16 ... eth0: unavailable "eth0" ethernet (fec), D0:63:B4:00:87:DD, hw, mtu 1500 ... nmcli con NAME UUID TYPE DEVICE br-4ba53c1beb78 580cd8d0-4b87-432d-b072-7b2191fc3dc8 bridge br-4ba53c1beb78 br-667404d55215 21ae2dad-0462-4880-98f2-8b56ae09dafa bridge br-667404d55215 br-7d46b681eda0 3dc1b651-2795-45fe-9821-7b33111d038c bridge br-7d46b681eda0 my-wlan 5d87696c-418b-404b-a6be-a85fd10c89cf wifi wlan0 Armbian ethernet 0a5bb1f6-799d-476f-9fe4-2ecc7f4fe055 ethernet -- nmcli con up 'Armbian ethernet' Error: Connection activation failed: No suitable device found for this connection (device eth0 not available because device has no carrier). sudo ip a ... 2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether d0:63:b4:00:87:dd brd ff:ff:ff:ff:ff:ff 3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 6c:ad:f8:1d:36:25 brd ff:ff:ff:ff:ff:ff inet 10.1.0.41/22 brd 10.1.3.255 scope global dynamic noprefixroute wlan0 valid_lft 85910sec preferred_lft 85910sec ... sudo ip link set eth0 up RTNETLINK answers: No such device EDIT: this is link to armbianmonitor after downgrading back to 5.7.15 and ethernet (eth0) working once again http://ix.io/2zHa
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines