Jump to content

Zamana

Validating
  • Posts

    2
  • Joined

  • Last visited

  1. Hello martinayotte! Minutes after I posted my question, I found your first reply in another thread that lead me to the right path. I just don't replied here yesterday due to the limit of one post per day. Beyond this, one of the pins was wrong. With Orange Pi PC and that sensor, the correct is use 3.3V, and not 5V. So, for the red wire, PIN 1, and not 2. Now my temperature monitor system is alive and kicking! Thank you very much!
  2. Dear Sirs, I read every topic in this thread (what helped me a lot), but now I'm stucked and need more help. I did buy this sensor and I need to use it on my Orange Pi PC. After following the instructions from this site together with the instruction of this thread, I wired the 3 cables like this: RED -> 2 (5V) BLACK -> 6 (GND) YELLOW -> 35 (PA10) My files are like this: root@orangepipc:/sys/bus/w1# cat /etc/modules-load.d/modules.conf # /etc/modules: kernel modules to load at boot time. # # This file contains the names of kernel modules that should be loaded # at boot time, one per line. Lines beginning with "#" are ignored. w1-sunxi w1-gpio w1-therm #sunxi-cir ##xradio_wlan g_serial ##xradio_wlan root@orangepipc:/sys/bus/w1# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 w1-gpio rootdev=UUID=88adacec-2194-4cfc-abc4-67cd6ef7fdf4 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u root@orangepipc:/sys/bus/w1/devices/w1_bus_master1# cat /etc/default/cpufrequtils ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive The loaded modules are these: root@orangepipc:/sys/bus/w1# lsmod Module Size Used by rfkill 20480 1 snd_soc_hdmi_codec 20480 1 sch_fq_codel 20480 2 dw_hdmi_i2s_audio 16384 0 dw_hdmi_cec 16384 0 sunxi_cir 20480 0 lima 45056 0 sun4i_gpadc_iio 16384 0 gpu_sched 28672 1 lima industrialio 53248 1 sun4i_gpadc_iio usb_f_acm 20480 1 sun8i_thermal 16384 0 u_serial 24576 1 usb_f_acm g_serial 16384 0 sun8i_ce 24576 0 libcomposite 45056 2 g_serial,usb_f_acm sunxi_cedrus 32768 0 sun8i_di 20480 0 crypto_engine 16384 1 sun8i_ce evdev 20480 1 uio_pdrv_genirq 16384 0 display_connector 20480 0 uio 16384 1 uio_pdrv_genirq cpufreq_dt 20480 0 zram 24576 2 w1_therm 24576 0 w1_gpio 16384 0 wire 32768 2 w1_gpio,w1_therm cn 16384 1 wire ip_tables 24576 0 x_tables 24576 1 ip_tables autofs4 36864 2 sy8106a_regulator 16384 1 sunxi 20480 0 phy_generic 20480 2 sunxi gpio_keys 20480 0 dmesg: root@orangepipc:~# dmesg | grep -i wire [ 6.506017] Driver for 1-wire Dallas network protocol. [ 6.523698] gpio-110 (onewire@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file (...) [ 1232.791932] w1_master_driver w1_bus_master1: Family 0 for 00.980000000000.d3 is not registered. [ 1278.638733] w1_master_driver w1_bus_master1: Attaching one wire slave 00.580000000000 crc 19 [ 1278.650463] w1_master_driver w1_bus_master1: Family 0 for 00.580000000000.19 is not registered. [ 1326.305393] w1_master_driver w1_bus_master1: Attaching one wire slave 00.d80000000000 crc 95 [ 1326.316126] w1_master_driver w1_bus_master1: Family 0 for 00.d80000000000.95 is not registered. [ 1350.471284] w1_master_driver w1_bus_master1: Attaching one wire slave 00.380000000000 crc 7c [ 1350.481274] w1_master_driver w1_bus_master1: Family 0 for 00.380000000000.7c is not registered. [ 1396.431767] w1_master_driver w1_bus_master1: Attaching one wire slave 00.b80000000000 crc f0 [ 1396.439186] w1_master_driver w1_bus_master1: Family 0 for 00.b80000000000.f0 is not registered. It seems that I have 2 sensors: root@orangepipc:~# cat /sys/devices/w1_bus_master1/w1_master_slave_count 2 But it seems that I don't have any files where to read the data... Example: root@orangepipc:/sys/bus/w1/devices/w1_bus_master1# tree -L 10 . ├── 00-200000000000 │ ├── driver -> ../../../bus/w1/drivers/w1_slave_driver │ ├── id │ ├── name │ ├── power │ │ ├── autosuspend_delay_ms │ │ ├── control │ │ ├── runtime_active_time │ │ ├── runtime_status │ │ └── runtime_suspended_time │ ├── rw │ ├── subsystem -> ../../../bus/w1 │ └── uevent ├── 00-a00000000000 │ ├── driver -> ../../../bus/w1/drivers/w1_slave_driver │ ├── id │ ├── name │ ├── power │ │ ├── autosuspend_delay_ms │ │ ├── control │ │ ├── runtime_active_time │ │ ├── runtime_status │ │ └── runtime_suspended_time │ ├── rw │ ├── subsystem -> ../../../bus/w1 │ └── uevent ├── driver -> ../../bus/w1/drivers/w1_master_driver ├── power │ ├── autosuspend_delay_ms │ ├── control │ ├── runtime_active_time │ ├── runtime_status │ └── runtime_suspended_time ├── subsystem -> ../../bus/w1 ├── uevent ├── w1_master_add ├── w1_master_attempts ├── w1_master_max_slave_count ├── w1_master_name ├── w1_master_pointer ├── w1_master_pullup ├── w1_master_remove ├── w1_master_search ├── w1_master_slave_count ├── w1_master_slaves ├── w1_master_timeout └── w1_master_timeout_us 11 directories, 36 files That's my system: ___ ____ _ ____ ____ / _ \| _ \(_) | _ \ / ___| | | | | |_) | | | |_) | | | |_| | __/| | | __/| |___ \___/|_| |_| |_| \____| Welcome to Armbian 20.08.7 Focal with Linux 5.8.13-sunxi System load: 8% Up time: 6 min Memory usage: 8% of 998M IP: 192.168.0.69 CPU temp: 45°C Usage of /: 14% of 7.2G [ General system configuration (beta): armbian-config ] Does anybody knows what I'm doing wrong? Any help is appreciated. Thanks. Regards.
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines