Ryanfab

still can't install to emmc but run well on micro SD

how to do that ? i install using install-aml.sh is failed it's 1gb ram and 8 gb emmc. should I change the dtb ? here is my armbian log http://ix.io/3JvI my trial on Armbian_20.10_Arm-64_focal_current_5.9.0_desktop.xz from https://disk.yandex.ru/d/_rQgn_FosYuW0g/20.10/20201014

root@arm-64:~# fdisk -l /dev/mmcblk1 Disk /dev/mmcblk1: 7.3 GiB, 7818182656 bytes, 15269888 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x8b04b650 Device Boot Start End Sectors Size Id Type /dev/mmcblk1p1 1953792 2953215 999424 488M c W95 FAT32 (LBA) /dev/mmcblk1p2 2955264 15269887 12314624 5.9G 83 Linux root@arm-64:~# fdisk -l /dev/mmcblk0 Disk /dev/mmcblk0: 14.9 GiB, 15931539456 bytes, 31116288 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x7272c9e5 Device Boot Start End Sectors Size Id Type /dev/mmcblk0p1 32768 1081343 1048576 512M e W95 FAT16 (LBA) /dev/mmcblk0p2 1081344 30805119 29723776 14.2G 83 Linux

my board S902x I have download Armbian_20.10_Arm-64_bionic_current_5.9.0.xz from https://disk.yandex.ru/d/_rQgn_FosYuW0g/20.10/20201014 I extract xz -d Armbian_20.10_Arm-64_bionic_current_5.9.0.xz then burn using balena some changes are extlinux/extlinux.conf LABEL Armbian LINUX /zImage INITRD /uInitrd FDT /dtb/amlogic/meson-gxl-s905x-p212.dtb APPEND root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 boot.ini become ODROIDN2-UBOOT-CONFIG if test "${devtype}" = ""; then setenv devtype "/dtb/amlogic/meson-gxl-s905x-p212.dtb"; fi if fatload ${devtype} ${devnum} 0x1000000 u-boot.ext; then go 0x1000000; fi; rename u-boot-s905x-s912 to u-boot.ext when I put on reboot_mode=cold_boot InUsbBurn [MSG]sof Set Addr 6 Get DT cfg Get DT cfg Get DT cfg set CFG then I send command from windows cli updater c:\update bulkcmd "run start_mmc_autoscript;" I can running linux I need advice to install to emmc, appreciate your response. thank you

I am using the one from instruction link https://disk.yandex.ru/d/_rQgn_FosYuW0g/20.10/20201014 Armbian_20.10_Arm-64_focal_current_5.9.0

success to execute and running into armbian but from InUsbBurn mode. with this command update bulkcmd "run start_mmc_autoscript;" any suggestion to make run on bootmode=NORM and install to mmc ?

my image is Armbian_5.88_Aml-s905_Ubuntu_bionic_default_5.1.0_desktop_20190530.img I guess the load address need to revise setenv env_addr "0x10400000" setenv kernel_addr "0x11000000" setenv initrd_addr "0x13000000" need suggestion

I try to execute start_mmc_autoscript BULKcmd[run start_mmc_autoscript] card in [mmc_init] mmc init success reading s905_autoscript 1765 bytes read in 5 ms (344.7 KiB/s) ## Executing script at 01020000 ** Bad device usb 0 ** ** Bad device usb 1 ** ** Bad device usb 2 ** ** Bad device usb 3 ** reading zImage 20537352 bytes read in 1141 ms (17.2 MiB/s) reading uInitrd 9426258 bytes read in 522 ms (17.2 MiB/s) reading uEnv.ini 209 bytes read in 7 ms (28.3 KiB/s) reading /dtb/meson-gxl-s905x-p212.dtb 25911 bytes read in 9 ms (2.7 MiB/s) ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 9426194 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK use dts in boot.img/recovery.img instead of dts partition. "Synchronous Abort" handler, esr 0x96000210 ELR: 3fec18b4 LR: 3febcd24 x0 : 0000000000000000 x1 : 0000000000000000 x2 : 000000003fed3c20 x3 : 0000000000000001 x4 : 000000003be9c950 x5 : 0000000000000000 x6 : 00000000ffffffc8 x7 : 0000000000000044 x8 : 0000000000000031 x9 : 0000000000000000 x10: 000000000000000f x11: 000000003ff38e40 x12: 0000000000000000 x13: 0000000000000000 x14: 0000000000000000 x15: 0000000000000000 x16: 0000000000000000 x17: 0000000000000000 x18: 000000003be9ee28 x19: 000000003ff6f4c8 x20: 0000000000000000 x21: 0000000000000003 x22: 000000003beba388 x23: 0000000000000000 x24: 0000000000000000 x25: 000000003ff3f000 x26: 0000000000000000 x27: 000000003beba3b0 x28: 0000000000000000 x29: 000000003be9cbe0 Resetting CPU ... resetting ... ~~~~....................................................................set vcck to 1070 mv set vddee to 1070 mv U-Boot 2015.01-ge1b7b3f-dirty (Aug 24 2017 - 23:11:22) DRAM: 1 GiB Relocation Offset is: 3eeaf000 not working

just now I burn image on sdcard and change some file boot.ini changed into this ODROIDN2-UBOOT-CONFIG if test "${devtype}" = ""; then setenv devtype "/dtb/amlogic/meson-gxl-s905x-p212.dtb"; fi if fatload ${devtype} ${devnum} 0x1000000 u-boot.ext; then go 0x1000000; fi; extlinux/extlinux.conf changed into this LABEL Armbian LINUX /zImage INITRD /uInitrd FDT /dtb/amlogic/meson-gxl-s905x-p212.dtb APPEND root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 rename u-boot-s905x2-s912 to u-boot.ext then I push the button to reset then i found it search on reading aml_autoscript finally got this ## Error: "bootfromsd" not defined need advice about this

here my printenv

@SteeMan, thanks for your response. I found tool updater from windows command line that I can set uboot param like this update bulkcmd “setenv -f EnableSelinux permissive” update bulkcmd “saveenv” I press switch button on upper right corner and put power switch and usb togather I got this response what u-boot command to make it multiboot? then I put sdcard with armbian image with modified extlinux, boot.ini, rename u-boot.ext I still cann't boot to sdcard. need your guidance.

appriciate your response @SteeMan. now, I have fresh reinstall firmware and my android box is running and rooted, but, my box doesn't boot from sdcard, because I think it doesn't support multi boot, my question is how to make my box start from sdcard ? do I need to change /dev/block/bootloader on my android ? soo I can follow installation instruction. FYI, my board doesn't have reset button.

my device is using amlogic s905 U-Boot 2015.01-ge1b7b3f-dirty (Jul 22 2017 - 16:51:56) Linux version 3.14.29-g9b417e7-dirty (wulinkui@A23131934) here is the detail, device has been rooted https://pastebin.com/H7NskL64 I have make bootable my sdcard with Armbian_5.89_Aml-s905_Debian_buster_default_5.1.0_desktop_20190617, but maybe original firmware doesn't support multi boot, which one that compatible with my amlogic and how to do that. I have read there is 2 method to make multi boot, toothpick and and update mode of the standard firmware I have try to dd if=u-boot.bin of=/dev/block/bootloader it won't run and my box become blank and I check from UART there is no boot log just set vddee to 1000 mv ~~~~.......................................................................................set vcck to 1120 mv I jumper C125 while put power cable + put USB + power button then refirmware with original firmware to run android. what I want to do is change android to armbian through make first to multiboot, CMIIW thank you and appreciate to response my question.

I am running Armbian on SD card on Amlogic Meson GXL (S905X) P212. I want to install to Emmc using /root/install-aml-s905-emmc.sh but failed since different script I thinks. here is my armbianmonitor -u http://ix.io/2He7 any script do I need to change inside /root/install-aml-s905-emmc.sh thank you