btrfs

thx to post of successful run yesterday so i find i cant load from any 32 GB card but works on 16GB. assuming card in ur run 64GB and tha ti can run 4.9 linux from 32 gb its some driver timing error cuz not depend on file systems. i got some error data from driver error occurs on fs runtime but never on bootimg load on start in: Mounting roo[ 3.914411] dwmac-sun8i 5020000.ethernet: TX Checksum insertion supported t file system ..[ 3.922603] dwmac-sun8i 5020000.ethernet: Normal descriptors . Begin: Running[ 3.929684] dwmac-sun8i 5020000.ethernet: Chain mode enabled /scripts/local-[ 3.937249] libphy: stmmac: probed top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. [ 3.968273] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.978283] mmc0: new high speed SDHC card at address 0001 [ 3.984807] mmcblk0: mmc0:0001 SD 29.2 GiB [ 3.990677] mmcblk0: p1 p2 p3 [ 4.006865] random: fast init done [ 4.130966] sunxi-mmc 4020000.mmc: irq 23 opcode 18 error -110 blksize 512 blk_addr 61156183 flags 512 data error, sending stop command [ 5.140649] sunxi-mmc 4020000.mmc: send stop command failed [ 33.764700] usb1-vbus: disabling [ 33.767942] vcc3v3-ext: disabling [ 33.771618] vcc3v3-ext2: disabling [ 33.775338] cldo1: disabling or that Begin: Will now check root file system ... fsck from util-linux 2.34 [/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1 /dev/mmcblk0p1: [ 4.395397] sunxi-mmc 4020000.mmc: irq 23 opcode 25 error -110 blksize 512 blk_addr 1056768 flags 256 data error, sending stop command but thats all i could understand for now

. Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems [ 3.934244] sun50i-h616-pinctrl 300b000.pinctrl: supply vcc-pf not found, using dummy regulator [ 3.944448] sunxi-mmc 4020000.mmc: Got CD GPIO done. [ 3.972822] sunxi-mmc 4020000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 4.018158] mmc0: host does not support reading read-only switch, assuming write-enable [ 4.028069] mmc0: new high speed SDHC card at address 0001 [ 4.034421] mmcblk0: mmc0:0001 SD 29.2 GiB [ 4.040510] mmcblk0: p1 p2 [ 4.052644] random: fast init done [ 4.080309] sunxi-mmc 4020000.mmc: data error, sending stop command [ 4.086606] sunxi-mmc 4020000.mmc: send stop command failed [ 33.760590] usb1-vbus: disabling [ 33.763836] vcc3v3-ext: disabling [ 33.767485] vcc3v3-ext2: disabling [ 33.771202] cldo1: disabling can't run any image getting same error. image from orangepi on 4.9 linux work but i need driver for mt6701u which is not present there, and AP mode not work. please help to run image. i'm new to builds with git. tried different sd cards. spent week building images with different config and patches from this thread all same error.