

beretas
-
Posts
6 -
Joined
-
Last visited
Content Type
Forums
Store
Crowdfunding
Applications
Events
Raffles
Community Map
Posts posted by beretas
-
-
Sorry for late reply.
For the record: MXQ PRO 4K 5G, announced on sitck as 4GB Ram, 32GB ROM, Rk3229. Inside it was Rk3228A, 1GB DDR3L Ram and 8GB NAND ROM of unknown chinesse manufacturer.
@jock definitely, Nand is not detected with multitool, only armbian can be loaded from SD Card after erasing Nand.
for the record or anyone with same system:
1.- Rom detection with rkdeveloptool:
rkdeveloptool rfi
Flash Info:
Manufacturer: SAMSUNG, value=00
Flash Size: 7301 MB
Flash Size: 14952960 Sectors
Block Size: 16384 KB
Page Size: 16 KB
ECC Bits: 40
Access Time: 32
Flash CS: Flash<0>2.- Flash cant be erased directly, on new system, if you do "rkdeveloptool ef" it writes: "Starting to erase flash..." and got stuck there, blocked, forever (i waited 24h, think its enough). So working method to get flash erased, its:
rkdeveloptool wl 0x4000 u-boot-main.img (you can download and check command on first post)
Write LBA from file (100%)after it, disconnect and reconnect again with the toothpick and Male-Male usb again. I tried to do "rkdeveloptool rd 3" which is supposed to reset device on MaskRoom mode, it responds: "Reset Device OK." but things cant be done, with errors like: "Getting flash info from device failed!". So after writing u-boot, disconnect and reconnect.
rkdeveloptool ef
Erasing flash complete.after it, plug SD card with Armbian and it boots ok. NAND is not useable from it, as it recognizes but can be accessed.
if it helps someone, loading system with thoothpick method and Male-Male usb gives this result also:
rkdeveloptool ld
DevNo=1 Vid=0x2207,Pid=0x320b,LocationID=301 LoaderHope this helps someone.
Best Regards,
Beretas
-
@jock rk322x-config already done selecting NAND. If its helpfull to you, i can connect machine to some PPTP or OpenVPN so you can log in to do any test you want.
Armbian-hardware-monitor.log:
### Activated 1 lzo zram swap devices with 481 MB each### Activated Armbian ramlog partition with lz4 compression
Sun 23 May 2021 07:17:07 AM CDT | rk322x-box | 21.05.2 | armhf | armv7l | 4.4.194-rk322x
### dmesg:
[ 0.000000] Booting Linux on physical CPU 0xf00
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.194-rk322x (root@hirsute) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) ) #3 SMP Thu May 6 22:00:38 UTC 2021
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Generic RK322x TV Box board
[ 0.000000] cma: Reserved 16 MiB at 0x9f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 253952
[ 0.000000] free_area_init_node: node 0, pgdat b1253b40, node_mem_map ee6f1000
[ 0.000000] Normal zone: 2304 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 253952 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] PERCPU: Embedded 14 pages/cpu @ee68f000 s24856 r8192 d24296 u57344
[ 0.000000] pcpu-alloc: s24856 r8192 d24296 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251648
[ 0.000000] Kernel command line: earlyprintk root=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db console=ttyS2,115200n8 console=tty1 rootwait rootfstype=ext4 consoleblank=0 loglevel=1 ubootpart=73c5b759-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u coherent_pool=2M cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 962664K/1015808K available (12862K kernel code, 919K rwdata, 3240K rodata, 808K init, 1219K bss, 36760K reserved, 16384K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
lowmem : 0xb0000000 - 0xf0000000 (1024 MB)
pkmap : 0xafe00000 - 0xb0000000 ( 2 MB)
modules : 0xaf000000 - 0xafe00000 ( 14 MB)
.text : 0xb0008000 - 0xb0c97c6c (12864 kB)
.init : 0xb10b0000 - 0xb117a000 ( 808 kB)
.data : 0xb117a000 - 0xb125fe94 ( 920 kB)
.bss : 0xb1261000 - 0xb1391f14 (1220 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000022] Switching to timer-based delay loop, resolution 41ns
[ 0.001795] Console: colour dummy device 80x30
[ 0.001978] console [tty1] enabled
[ 0.002004] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.002022] pid_max: default: 32768 minimum: 301
[ 0.002153] Security Framework initialized
[ 0.002167] Yama: becoming mindful.
[ 0.002242] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002258] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.003142] Initializing cgroup subsys io
[ 0.003175] Initializing cgroup subsys memory
[ 0.003217] Initializing cgroup subsys devices
[ 0.003236] Initializing cgroup subsys freezer
[ 0.003254] Initializing cgroup subsys net_cls
[ 0.003270] Initializing cgroup subsys perf_event
[ 0.003287] Initializing cgroup subsys net_prio
[ 0.003317] Initializing cgroup subsys pids
[ 0.003387] CPU: Testing write buffer coherency: ok
[ 0.003434] ftrace: allocating 41892 entries in 123 pages
[ 0.082721] /cpus/cpu@f00 missing clock-frequency property
[ 0.082753] /cpus/cpu@f01 missing clock-frequency property
[ 0.082772] /cpus/cpu@f02 missing clock-frequency property
[ 0.082791] /cpus/cpu@f03 missing clock-frequency property
[ 0.082803] CPU0: update cpu_capacity 430
[ 0.082814] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[ 0.082899] Setting up static identity map for 0x60008280 - 0x600082d8
[ 0.094091] CPU1: update cpu_capacity 430
[ 0.094100] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[ 0.103588] CPU2: update cpu_capacity 430
[ 0.103597] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[ 0.113036] CPU3: update cpu_capacity 430
[ 0.113044] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[ 0.113180] Brought up 4 CPUs
[ 0.113220] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.113228] CPU: All CPU(s) started in SVC mode.
[ 0.114750] devtmpfs: initialized
[ 0.134406] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.134990] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.135032] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.136369] xor: measuring software checksum speed
[ 0.174755] arm4regs : 1011.000 MB/sec
[ 0.214859] 8regs : 705.000 MB/sec
[ 0.254961] 32regs : 684.000 MB/sec
[ 0.295063] neon : 1018.000 MB/sec
[ 0.295073] xor: using function: neon (1018.000 MB/sec)
[ 0.295114] pinctrl core: initialized pinctrl subsystem
[ 0.296673] NET: Registered protocol family 16
[ 0.299203] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.311215] cpuidle: using governor ladder
[ 0.323228] cpuidle: using governor menu
[ 0.339652] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0
[ 0.339815] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1
[ 0.339974] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2
[ 0.340126] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3
[ 0.346352] console [pstore-1] enabled
[ 0.346364] pstore: Registered ramoops as persistent store backend
[ 0.346376] ramoops: attached 0xf0000@0x62e00000, ecc: 0/0
[ 0.349711] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.349731] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.349939] sip_firmware_init: set rockchip sip version v2 failed
[ 0.448068] raid6: int32x1 gen() 133 MB/s
[ 0.516187] raid6: int32x1 xor() 131 MB/s
[ 0.584413] raid6: int32x2 gen() 166 MB/s
[ 0.652668] raid6: int32x2 xor() 137 MB/s
[ 0.720820] raid6: int32x4 gen() 163 MB/s
[ 0.788995] raid6: int32x4 xor() 137 MB/s
[ 0.857223] raid6: int32x8 gen() 166 MB/s
[ 0.925487] raid6: int32x8 xor() 113 MB/s
[ 0.993617] raid6: neonx1 gen() 382 MB/s
[ 1.061752] raid6: neonx1 xor() 290 MB/s
[ 1.129937] raid6: neonx2 gen() 519 MB/s
[ 1.198091] raid6: neonx2 xor() 376 MB/s
[ 1.266282] raid6: neonx4 gen() 581 MB/s
[ 1.334493] raid6: neonx4 xor() 400 MB/s
[ 1.402787] raid6: neonx8 gen() 560 MB/s
[ 1.470934] raid6: neonx8 xor() 391 MB/s
[ 1.470947] raid6: using algorithm neonx4 gen() 581 MB/s
[ 1.470956] raid6: .... xor() 400 MB/s, rmw enabled
[ 1.470966] raid6: using intx1 recovery algorithm
[ 1.471947] rockchip-pm rockchip-suspend: not set wakeup-config
[ 1.471969] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 1.472338] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@0[0]'
[ 1.472829] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@1[0]'
[ 1.473464] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc-host-regulator[0]' - status (0)
[ 1.474068] of_get_named_gpiod_flags: parsed 'gpio' property of node '/otg-vbus-regulator[0]' - status (0)
[ 1.474560] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]'
[ 1.475464] iommu: Adding device 20020000.vpu-service to group 0
[ 1.475582] iommu: Adding device 20030000.rkvdec to group 1
[ 1.475680] iommu: Adding device 20050000.vop to group 2
[ 1.475773] iommu: Adding device 20070000.iep to group 3
[ 1.476294] rk_iommu 20020800.iommu: can't get sclk
[ 1.476864] rk_iommu 20030480.iommu: can't get sclk
[ 1.477126] rk_iommu 20053f00.iommu: can't get sclk
[ 1.477274] rk_iommu 20070800.iommu: can't get aclk
[ 1.477294] rk_iommu 20070800.iommu: can't get hclk
[ 1.477310] rk_iommu 20070800.iommu: can't get sclk
[ 1.478053] SCSI subsystem initialized
[ 1.478468] usbcore: registered new interface driver usbfs
[ 1.478568] usbcore: registered new interface driver hub
[ 1.478689] usbcore: registered new device driver usb
[ 1.478911] media: Linux media interface: v0.10
[ 1.479070] Linux video capture interface: v2.00
[ 1.479321] pps_core: LinuxPPS API ver. 1 registered
[ 1.479337] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.479379] PTP clock support registered
[ 1.481288] Advanced Linux Sound Architecture Driver Initialized.
[ 1.482281] Bluetooth: Core ver 2.21
[ 1.482347] NET: Registered protocol family 31
[ 1.482363] Bluetooth: HCI device and connection manager initialized
[ 1.482385] Bluetooth: HCI socket layer initialized
[ 1.482401] Bluetooth: L2CAP socket layer initialized
[ 1.482457] Bluetooth: SCO socket layer initialized
[ 1.483298] NetLabel: Initializing
[ 1.483320] NetLabel: domain hash size = 128
[ 1.483330] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.483403] NetLabel: unlabeled traffic allowed by default
[ 1.484727] clocksource: Switched to clocksource arch_sys_counter
[ 1.579695] NET: Registered protocol family 2
[ 1.580557] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.580672] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 1.581108] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.581211] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 1.581281] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 1.581631] NET: Registered protocol family 1
[ 1.582297] RPC: Registered named UNIX socket transport module.
[ 1.582319] RPC: Registered udp transport module.
[ 1.582330] RPC: Registered tcp transport module.
[ 1.582341] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.582662] Trying to unpack rootfs image as initramfs...
[ 1.955624] Freeing initrd memory: 5564K
[ 1.956635] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 1.959596] Initialise system trusted keyring
[ 1.973444] VFS: Disk quotas dquot_6.6.0
[ 1.973755] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.976412] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.979832] NFS: Registering the id_resolver key type
[ 1.979914] Key type id_resolver registered
[ 1.979926] Key type id_legacy registered
[ 1.979961] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.980072] ntfs: driver 2.1.32 [Flags: R/W].
[ 1.981131] JFS: nTxBlock = 7692, nTxLock = 61538
[ 1.989710] SGI XFS with security attributes, no debug enabled
[ 1.998270] NET: Registered protocol family 38
[ 1.998322] Key type asymmetric registered
[ 1.998341] Asymmetric key parser 'x509' registered
[ 1.998738] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 1.999075] io scheduler noop registered
[ 1.999102] io scheduler deadline registered
[ 1.999183] io scheduler cfq registered (default)
[ 2.002347] phy phy-11000000.syscon:usb2-phy@800.2: Failed to get VBUS supply regulator
[ 2.007337] rk-vcodec 20020000.vpu-service: no regulator for vcodec
[ 2.007800] rk-vcodec 20020000.vpu-service: probe device
[ 2.008208] rk-vcodec 20020000.vpu-service: drm allocator with mmu enabled
[ 2.009413] rk-vcodec 20020000.vpu-service: could not find power_model node
[ 2.009440] rk-vcodec 20020000.vpu-service: init success
[ 2.009761] rk-vcodec 20030000.rkvdec: vcodec regulator not ready, retry
[ 2.013982] dma-pl330 110f0000.pdma: Loaded driver for PL330 DMAC-241330
[ 2.014010] dma-pl330 110f0000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 2.015123] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 2.015587] pwm-regulator vdd-arm-regulator: GPIO lookup for consumer enable
[ 2.015606] pwm-regulator vdd-arm-regulator: using device tree for GPIO lookup
[ 2.015623] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-arm-regulator[0]'
[ 2.015638] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-arm-regulator[0]'
[ 2.015651] pwm-regulator vdd-arm-regulator: using lookup tables for GPIO lookup
[ 2.015666] pwm-regulator vdd-arm-regulator: lookup for GPIO enable failed
[ 2.016307] pwm-regulator vdd-log-regulator: GPIO lookup for consumer enable
[ 2.016328] pwm-regulator vdd-log-regulator: using device tree for GPIO lookup
[ 2.016343] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log-regulator[0]'
[ 2.016358] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log-regulator[0]'
[ 2.016371] pwm-regulator vdd-log-regulator: using lookup tables for GPIO lookup
[ 2.016386] pwm-regulator vdd-log-regulator: lookup for GPIO enable failed
[ 2.017518] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.018301] 11030000.serial: ttyS2 at MMIO 0x11030000 (irq = 30, base_baud = 1500000) is a 16550A
[ 2.019127] console [ttyS2] enabled
[ 2.020922] [drm] Initialized drm 1.1.0 20060810
[ 2.023330] [drm] Rockchip DRM driver version: v1.0.1
[ 2.023569] rockchip-drm display-subsystem: devfreq is not set
[ 2.024295] rockchip-drm display-subsystem: bound 20050000.vop (ops 0xb0d1b2b0)
[ 2.024694] i2c i2c-0: of_i2c: modalias failure on /hdmi@200a0000/ports
[ 2.024777] dwhdmi-rockchip 200a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 2.024902] dwhdmi-rockchip 200a0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (inno_dw_hdmi_phy)
[ 2.026126] rockchip-drm display-subsystem: bound 200a0000.hdmi (ops 0xb0d13808)
[ 2.026150] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.026160] [drm] No driver support for vblank timestamp query.
[ 2.026301] rockchip-drm display-subsystem: failed to parse display resources
[ 2.026364] rockchip-drm display-subsystem: No connectors reported connected with modes
[ 2.026450] [drm] Cannot find any crtc or sizes - going 1024x768
[ 2.049183] Console: switching to colour frame buffer device 128x48
[ 2.064565] rockchip-drm display-subsystem: fb0: frame buffer device
[ 2.077291] Registered IR keymap rc-cec
[ 2.077548] rc rc0: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0
[ 2.078214] input: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0/input0
[ 2.080291] brd: module loaded
[ 2.091631] loop: module loaded
[ 2.091699] lkdtm: No crash points registered, enable through debugfs
[ 2.094210] libphy: Fixed MDIO Bus: probed
[ 2.094244] tun: Universal TUN/TAP device driver, 1.6
[ 2.094256] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.094605] CAN device driver interface
[ 2.095980] rk_gmac-dwmac 30200000.ethernet: clock input or output? (output).
[ 2.096007] rk_gmac-dwmac 30200000.ethernet: TX delay(0x30).
[ 2.096023] rk_gmac-dwmac 30200000.ethernet: RX delay(0x10).
[ 2.096065] rk_gmac-dwmac 30200000.ethernet: integrated PHY? (yes).
[ 2.096235] rk_gmac-dwmac 30200000.ethernet: cannot get clock clk_mac_speed
[ 2.101313] rk_gmac-dwmac 30200000.ethernet: init for RMII
[ 2.136851] stmmac - user ID: 0x10, Synopsys ID: 0x35
[ 2.136867] Ring mode enabled
[ 2.136878] DMA HW capability register supported
[ 2.136887] Normal descriptors
[ 2.136899] RX Checksum Offload Engine supported (type 2)
[ 2.136908] TX Checksum insertion supported
[ 2.136916] Wake-Up On Lan supported
[ 2.137007] rk_gmac-dwmac 30200000.ethernet: rk_get_eth_addr: mac address: 06:5a:0e:81:f7:7c
[ 2.137020] eth%d: device MAC address 06:5a:0e:81:f7:7c
[ 2.137030] Enable RX Mitigation via HW Watchdog Timer
[ 2.137223] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@30200000[0]' - status (0)
[ 2.549100] libphy: stmmac: probed
[ 2.549129] eth%d: PHY ID 1234d400 at 0 IRQ POLL (stmmac-0:00) active
[ 2.549143] eth%d: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
[ 2.549156] eth%d: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
[ 2.549169] eth%d: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
[ 2.549181] eth%d: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
[ 2.549194] eth%d: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
[ 2.549206] eth%d: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
[ 2.549218] eth%d: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
[ 2.549230] eth%d: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
[ 2.549243] eth%d: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
[ 2.549255] eth%d: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
[ 2.549268] eth%d: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
[ 2.549280] eth%d: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
[ 2.549292] eth%d: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
[ 2.549304] eth%d: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
[ 2.549317] eth%d: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
[ 2.549329] eth%d: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
[ 2.549341] eth%d: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
[ 2.549354] eth%d: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
[ 2.549367] eth%d: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
[ 2.549379] eth%d: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
[ 2.549391] eth%d: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
[ 2.549403] eth%d: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
[ 2.549416] eth%d: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
[ 2.549428] eth%d: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
[ 2.549440] eth%d: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
[ 2.549452] eth%d: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
[ 2.549465] eth%d: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
[ 2.549477] eth%d: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
[ 2.549489] eth%d: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
[ 2.549501] eth%d: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
[ 2.549513] eth%d: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
[ 2.550936] PPP generic driver version 2.4.2
[ 2.551335] Atmel at76x USB Wireless LAN Driver 0.17 loading
[ 2.551473] usbcore: registered new interface driver at76c50x-usb
[ 2.551600] usbcore: registered new interface driver rtl8187
[ 2.551716] usbcore: registered new interface driver rndis_wlan
[ 2.551824] usbcore: registered new interface driver zd1201
[ 2.552237] usbcore: registered new interface driver rt2800usb
[ 2.552351] Rockchip WiFi SYS interface (V1.00) ...
[ 2.552421] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 2.552505] usbcore: registered new interface driver pegasus
[ 2.552591] usbcore: registered new interface driver rtl8150
[ 2.552673] usbcore: registered new interface driver r8152
[ 2.552842] usbcore: registered new interface driver asix
[ 2.552936] usbcore: registered new interface driver ax88179_178a
[ 2.553017] usbcore: registered new interface driver cdc_ether
[ 2.553111] usbcore: registered new interface driver dm9601
[ 2.553219] usbcore: registered new interface driver smsc75xx
[ 2.553324] usbcore: registered new interface driver smsc95xx
[ 2.553407] usbcore: registered new interface driver net1080
[ 2.553498] usbcore: registered new interface driver rndis_host
[ 2.553584] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 2.553724] usbcore: registered new interface driver cdc_ncm
[ 2.553816] usbcore: registered new interface driver cdc_mbim
[ 2.554298] 30040000.usb supply vusb_d not found, using dummy regulator
[ 2.554431] 30040000.usb supply vusb_a not found, using dummy regulator
[ 2.567548] dwc2 30040000.usb: DWC OTG Controller
[ 2.567599] dwc2 30040000.usb: new USB bus registered, assigned bus number 1
[ 2.567654] dwc2 30040000.usb: irq 48, io mem 0x30040000
[ 2.568007] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.568027] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.568041] usb usb1: Product: DWC OTG Controller
[ 2.568055] usb usb1: Manufacturer: Linux 4.4.194-rk322x dwc2_hsotg
[ 2.568068] usb usb1: SerialNumber: 30040000.usb
[ 2.569153] hub 1-0:1.0: USB hub found
[ 2.569230] hub 1-0:1.0: 1 port detected
[ 2.570779] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.570809] ehci-platform: EHCI generic platform driver
[ 2.573339] ehci-platform 30080000.usb: EHCI Host Controller
[ 2.573707] ehci-platform 30080000.usb: new USB bus registered, assigned bus number 2
[ 2.574000] ehci-platform 30080000.usb: irq 49, io mem 0x30080000
[ 2.584777] ehci-platform 30080000.usb: USB 2.0 started, EHCI 1.00
[ 2.585074] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.585093] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.585108] usb usb2: Product: EHCI Host Controller
[ 2.585122] usb usb2: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
[ 2.585136] usb usb2: SerialNumber: 30080000.usb
[ 2.586106] hub 2-0:1.0: USB hub found
[ 2.586181] hub 2-0:1.0: 1 port detected
[ 2.589086] ehci-platform 300c0000.usb: EHCI Host Controller
[ 2.589493] ehci-platform 300c0000.usb: new USB bus registered, assigned bus number 3
[ 2.589772] ehci-platform 300c0000.usb: irq 51, io mem 0x300c0000
[ 2.600774] ehci-platform 300c0000.usb: USB 2.0 started, EHCI 1.00
[ 2.601106] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.601127] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.601141] usb usb3: Product: EHCI Host Controller
[ 2.601155] usb usb3: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
[ 2.601169] usb usb3: SerialNumber: 300c0000.usb
[ 2.602159] hub 3-0:1.0: USB hub found
[ 2.602227] hub 3-0:1.0: 1 port detected
[ 2.605121] ehci-platform 30100000.usb: EHCI Host Controller
[ 2.605520] ehci-platform 30100000.usb: new USB bus registered, assigned bus number 4
[ 2.605826] ehci-platform 30100000.usb: irq 53, io mem 0x30100000
[ 2.616771] ehci-platform 30100000.usb: USB 2.0 started, EHCI 1.00
[ 2.617067] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.617086] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.617101] usb usb4: Product: EHCI Host Controller
[ 2.617114] usb usb4: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
[ 2.617128] usb usb4: SerialNumber: 30100000.usb
[ 2.618112] hub 4-0:1.0: USB hub found
[ 2.618179] hub 4-0:1.0: 1 port detected
[ 2.619000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.619049] ohci-platform: OHCI generic platform driver
[ 2.619438] ohci-platform 300a0000.usb: Generic Platform OHCI controller
[ 2.619829] ohci-platform 300a0000.usb: new USB bus registered, assigned bus number 5
[ 2.620092] ohci-platform 300a0000.usb: irq 50, io mem 0x300a0000
[ 2.677007] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.677030] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.677045] usb usb5: Product: Generic Platform OHCI controller
[ 2.677060] usb usb5: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
[ 2.677074] usb usb5: SerialNumber: 300a0000.usb
[ 2.678093] hub 5-0:1.0: USB hub found
[ 2.678166] hub 5-0:1.0: 1 port detected
[ 2.679021] ohci-platform 300e0000.usb: Generic Platform OHCI controller
[ 2.679437] ohci-platform 300e0000.usb: new USB bus registered, assigned bus number 6
[ 2.679682] ohci-platform 300e0000.usb: irq 52, io mem 0x300e0000
[ 2.737011] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.737034] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.737049] usb usb6: Product: Generic Platform OHCI controller
[ 2.737063] usb usb6: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
[ 2.737077] usb usb6: SerialNumber: 300e0000.usb
[ 2.738046] hub 6-0:1.0: USB hub found
[ 2.738120] hub 6-0:1.0: 1 port detected
[ 2.738924] ohci-platform 30120000.usb: Generic Platform OHCI controller
[ 2.739294] ohci-platform 30120000.usb: new USB bus registered, assigned bus number 7
[ 2.739531] ohci-platform 30120000.usb: irq 54, io mem 0x30120000
[ 2.797024] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.797047] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.797062] usb usb7: Product: Generic Platform OHCI controller
[ 2.797076] usb usb7: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
[ 2.797089] usb usb7: SerialNumber: 30120000.usb
[ 2.798076] hub 7-0:1.0: USB hub found
[ 2.798154] hub 7-0:1.0: 1 port detected
[ 2.799062] usbcore: registered new interface driver cdc_acm
[ 2.799080] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.799189] usbcore: registered new interface driver cdc_wdm
[ 2.799481] usbcore: registered new interface driver usb-storage
[ 2.799648] usbcore: registered new interface driver usbserial
[ 2.799728] usbcore: registered new interface driver usbserial_generic
[ 2.799808] usbserial: USB Serial support registered for generic
[ 2.799911] usbcore: registered new interface driver keyspan
[ 2.799970] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 2.800028] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 2.800086] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 2.800143] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 2.800258] usbcore: registered new interface driver option
[ 2.800319] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.801076] usbcore: registered new interface driver oti6858
[ 2.801149] usbserial: USB Serial support registered for oti6858
[ 2.801259] usbcore: registered new interface driver qcserial
[ 2.801334] usbserial: USB Serial support registered for Qualcomm USB modem
[ 2.801495] usbcore: registered new interface driver sierra
[ 2.801555] usbserial: USB Serial support registered for Sierra USB modem
[ 2.803043] usbcore: registered new interface driver iforce
[ 2.803203] usbcore: registered new interface driver xpad
[ 2.803500] usbcore: registered new interface driver usbtouchscreen
[ 2.804676] i2c /dev entries driver
[ 2.806671] IR NEC protocol handler initialized
[ 2.806699] IR RC5(x/sz) protocol handler initialized
[ 2.806717] IR RC6 protocol handler initialized
[ 2.806734] IR JVC protocol handler initialized
[ 2.806751] IR Sony protocol handler initialized
[ 2.806768] IR SANYO protocol handler initialized
[ 2.806785] IR Sharp protocol handler initialized
[ 2.806803] IR MCE Keyboard/mouse protocol handler initialized
[ 2.806820] IR XMP protocol handler initialized
[ 2.808505] usbcore: registered new interface driver uvcvideo
[ 2.808520] USB Video Class driver (1.1.1)
[ 2.810484] Boot mode: normal
[ 2.811673] rockchip-thermal 11150000.tsadc: tsadc is probed successfully!
[ 2.813398] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 2.813758] Bluetooth: Virtual HCI driver ver 1.5
[ 2.814042] Bluetooth: HCI UART driver ver 2.3
[ 2.814059] Bluetooth: HCI UART protocol H4 registered
[ 2.814071] Bluetooth: HCI UART protocol LL registered
[ 2.814081] Bluetooth: HCI UART protocol ATH3K registered
[ 2.814092] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.814257] Bluetooth: HCI UART protocol BCM registered
[ 2.814405] usbcore: registered new interface driver bfusb
[ 2.814544] usbcore: registered new interface driver btusb
[ 2.814566] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[ 2.815159] cpu cpu0: leakage=5
[ 2.815190] cpu cpu0: leakage-volt-sel=0
[ 2.815368] cpu cpu0: Failed to get pvtm
[ 2.816834] cpu cpu0: avs=0
[ 2.816912] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
[ 2.816937] cpu cpu0: failed to read out thermal zone (-22)
[ 2.817559] cpu cpu0: failed to find power_model node
[ 2.818203] pwrseq_simple sdio-pwrseq: GPIO lookup for consumer reset
[ 2.818220] pwrseq_simple sdio-pwrseq: using device tree for GPIO lookup
[ 2.818243] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0)
[ 2.818590] Synopsys Designware Multimedia Card Interface Driver
[ 2.819197] dwmmc_rockchip 30000000.dwmmc: IDMAC supports 32-bit address mode.
[ 2.819319] dwmmc_rockchip 30000000.dwmmc: Using internal DMA controller.
[ 2.819336] dwmmc_rockchip 30000000.dwmmc: Version ID is 270a
[ 2.819401] dwmmc_rockchip 30000000.dwmmc: DW MMC controller at irq 45,32 bit host data width,256 deep fifo
[ 2.819452] dwmmc_rockchip 30000000.dwmmc: No vmmc regulator found
[ 2.819463] dwmmc_rockchip 30000000.dwmmc: No vqmmc regulator found
[ 2.819485] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer cd
[ 2.819495] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
[ 2.819521] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/dwmmc@30000000[0]' - status (0)
[ 2.819558] gpio-49 (cd): gpiod_set_debounce: missing set() or set_debounce() operations
[ 2.819569] dwmmc_rockchip 30000000.dwmmc: Got CD GPIO
[ 2.819580] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer wp
[ 2.819589] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
[ 2.819599] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30000000[0]'
[ 2.819609] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30000000[0]'
[ 2.819618] dwmmc_rockchip 30000000.dwmmc: using lookup tables for GPIO lookup
[ 2.819628] dwmmc_rockchip 30000000.dwmmc: lookup for GPIO wp failed
[ 2.832448] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 2.845357] dwmmc_rockchip 30000000.dwmmc: 1 slots initialized
[ 2.845725] dwmmc_rockchip 30010000.dwmmc: num-slots property not found, assuming 1 slot is available
[ 2.845812] dwmmc_rockchip 30010000.dwmmc: IDMAC supports 32-bit address mode.
[ 2.845901] dwmmc_rockchip 30010000.dwmmc: Using internal DMA controller.
[ 2.845918] dwmmc_rockchip 30010000.dwmmc: Version ID is 270a
[ 2.845974] dwmmc_rockchip 30010000.dwmmc: DW MMC controller at irq 46,32 bit host data width,256 deep fifo
[ 2.846023] dwmmc_rockchip 30010000.dwmmc: No vmmc regulator found
[ 2.846034] dwmmc_rockchip 30010000.dwmmc: No vqmmc regulator found
[ 2.846053] dwmmc_rockchip 30010000.dwmmc: GPIO lookup for consumer wp
[ 2.846063] dwmmc_rockchip 30010000.dwmmc: using device tree for GPIO lookup
[ 2.846075] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30010000[0]'
[ 2.846085] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30010000[0]'
[ 2.846094] dwmmc_rockchip 30010000.dwmmc: using lookup tables for GPIO lookup
[ 2.846104] dwmmc_rockchip 30010000.dwmmc: lookup for GPIO wp failed
[ 2.846171] dwmmc_rockchip 30010000.dwmmc: allocated mmc-pwrseq
[ 2.858934] mmc_host mmc1: Bus speed (slot 0) = 976562Hz (slot req 400000Hz, actual 244140HZ div = 2)
[ 2.871581] dwmmc_rockchip 30010000.dwmmc: 1 slots initialized
[ 2.872203] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/auxiliary[0]' - status (0)
[ 2.872451] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/working[0]' - status (0)
[ 2.872893] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.873005] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.873500] usbcore: registered new interface driver usbhid
[ 2.873514] usbhid: USB HID core driver
[ 2.874533] ashmem: initialized
[ 2.877670] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 2.877781] mmc0: new high speed SDXC card at address 59b4
[ 2.879316] mmcblk0: mmc0:59b4 SD 57.8 GiB
[ 2.881016] rknandbase v1.2 2018-05-08
[ 2.881646] mmcblk0: p1
[ 2.883948] rknand 30030000.nandc: rknand_probe clk rate = 150000000
[ 2.884344] No.1 FLASH ID:ec de 94 c3 a4 ca
[ 2.884410] No.1 FLASH ID:ec de 94 c3 a4 ca
[ 2.885715] FlashLoadPhyInfo fail 800!!
[ 2.885750] ftl_init ffffffff
[ 2.885763] rk_ftl_init fail
[ 2.887487] usbcore: registered new interface driver snd-usb-audio
[ 2.887700] usbcore: registered new interface driver snd-ua101
[ 2.887982] usbcore: registered new interface driver snd-usb-caiaq
[ 2.888161] usbcore: registered new interface driver snd-usb-6fire
[ 2.888416] usbcore: registered new interface driver snd-usb-hiface
[ 2.888568] usbcore: registered new interface driver snd-bcd2000
[ 2.888782] usbcore: registered new interface driver snd_usb_pod
[ 2.889023] usbcore: registered new interface driver snd_usb_podhd
[ 2.889173] usbcore: registered new interface driver snd_usb_toneport
[ 2.889325] usbcore: registered new interface driver snd_usb_variax
[ 2.898324] u32 classifier
[ 2.898352] input device check on
[ 2.898365] Actions configured
[ 2.898395] Netfilter messages via NETLINK v0.30.
[ 2.898475] nfnl_acct: registering with nfnetlink.
[ 2.898620] nf_conntrack version 0.5.0 (15384 buckets, 61536 max)
[ 2.900090] Initializing XFRM netlink socket
[ 2.902105] NET: Registered protocol family 10
[ 2.904336] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.905151] sit: IPv6 over IPv4 tunneling driver
[ 2.906679] NET: Registered protocol family 17
[ 2.906751] NET: Registered protocol family 15
[ 2.906852] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.906931] Bridge firewalling registered
[ 2.906956] can: controller area network core (rev 20120528 abi 9)
[ 2.907078] NET: Registered protocol family 29
[ 2.907201] can: raw protocol (rev 20120528)
[ 2.907231] can: broadcast manager protocol (rev 20120528 t)
[ 2.907268] can: netlink gateway (rev 20130117) max_hops=1
[ 2.907981] Bluetooth: RFCOMM TTY layer initialized
[ 2.908030] Bluetooth: RFCOMM socket layer initialized
[ 2.908078] Bluetooth: RFCOMM ver 1.11
[ 2.908131] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.908259] Bluetooth: HIDP socket layer initialized
[ 2.908384] 8021q: 802.1Q VLAN Support v1.8
[ 2.908450] lib80211: common routines for IEEE802.11 drivers
[ 2.908469] lib80211_crypt: registered algorithm 'NULL'
[ 2.908497] lib80211_crypt: registered algorithm 'WEP'
[ 2.908525] lib80211_crypt: registered algorithm 'CCMP'
[ 2.908553] lib80211_crypt: registered algorithm 'TKIP'
[ 2.908576] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 2.909154] [BT_RFKILL]: Enter rfkill_rk_init
[ 2.909622] Key type dns_resolver registered
[ 2.910114] flash vendor_init_thread!
[ 2.910138] flash vendor storage:20170308 ret = -1
[ 2.910290] Error: Driver 'sc031gs' is already registered, aborting...
[ 2.911683] Registering SWP/SWPB emulation handler
[ 2.913690] registered taskstats version 1
[ 2.913785] Loading compiled-in X.509 certificates
[ 2.918970] Btrfs loaded
[ 2.920607] rga2: Driver loaded successfully ver:4.01
[ 2.921029] rga2: Module initialized.
[ 2.921144] pvtm list NULL
[ 2.922736] rk-vcodec 20030000.rkvdec: leakage=4
[ 2.922781] rk-vcodec 20030000.rkvdec: leakage-volt-sel=0
[ 2.922929] rk-vcodec 20030000.rkvdec: Failed to get pvtm
[ 2.923504] rk-vcodec 20030000.rkvdec: avs=0
[ 2.923907] rk-vcodec 20030000.rkvdec: probe device
[ 2.924501] rk-vcodec 20030000.rkvdec: drm allocator with mmu enabled
[ 2.924941] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 2.926103] rk-vcodec 20030000.rkvdec: init success
[ 2.926929] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/hdmi-sound[0]'
[ 2.926947] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/hdmi-sound[0]'
[ 2.927732] asoc-simple-card hdmi-sound: i2s-hifi <-> 100c0000.i2s0 mapping ok
[ 2.928518] mmc1: new high speed SDIO card at address 0001
[ 2.930132] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]'
[ 2.930154] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]'
[ 2.931002] asoc-simple-card spdif-sound: dit-hifi <-> 100d0000.spdif mapping ok
[ 2.932800] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/reset[0]' - status (0)
[ 2.932880] gpio-121 (reset): gpiod_set_debounce: missing set() or set_debounce() operations
[ 2.933197] input: gpio-keys as /devices/platform/gpio-keys/input/input1
[ 2.933611] hctosys: unable to open rtc device (rtc0)
[ 2.945002] ALSA device list:
[ 2.945028] #0: DW-I2S-HDMI
[ 2.945035] #1: SPDIF
[ 2.945920] Freeing unused kernel memory: 808K
[ 2.945931] This architecture does not have kernel memory protection.
[ 5.185830] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[ 5.932787] vendor storage:20190527 ret = -1
[ 5.949894] systemd[1]: System time before build time, advancing clock.
[ 5.974210] systemd[1]: Inserted module 'autofs4'
[ 5.980186] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.990921] cgroup: cgroup2: unknown option "nsdelegate"
[ 6.007112] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 6.008645] systemd[1]: Detected architecture arm.
[ 6.022904] systemd[1]: Set hostname to <server1>.
[ 6.195171] ttyS2 - failed to request DMA, use interrupt mode
[ 6.368891] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 6.368939] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 6.788880] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.814015] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 6.814155] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.819251] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 6.820196] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.820924] systemd[1]: Listening on udev Kernel Socket.
[ 6.821580] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.822446] systemd[1]: Listening on Journal Socket.
[ 6.823533] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.830134] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 6.831236] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.838684] systemd[1]: Starting Nameserver information manager...
[ 6.839627] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.839787] systemd[1]: Reached target Swap.
[ 6.840656] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[ 6.841172] random: systemd: uninitialized urandom read (16 bytes read, 128 bits of entropy available)
[ 6.886588] random: nonblocking pool is initialized
[ 6.890712] systemd[1]: Starting Restore / save the current clock...
[ 6.896040] systemd[1]: Created slice system-getty.slice.
[ 6.897492] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.898565] systemd[1]: Reached target Local Encrypted Volumes.
[ 6.900504] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 6.909973] systemd[1]: Mounting Kernel Debug File System...
[ 6.912124] systemd[1]: Listening on Syslog Socket.
[ 6.913455] systemd[1]: Reached target System Time Synchronized.
[ 6.951573] systemd[1]: Starting Set the console keyboard layout...
[ 6.952922] systemd[1]: Reached target Paths.
[ 6.954763] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 6.955985] systemd[1]: Reached target Remote File Systems.
[ 6.966904] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.981109] systemd[1]: Starting Load Kernel Modules...
[ 6.983598] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.985975] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 6.986939] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 6.996535] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 7.000551] systemd[1]: Listening on udev Control Socket.
[ 7.014204] systemd[1]: Starting udev Coldplug all Devices...
[ 7.016432] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 7.019717] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 7.024896] systemd[1]: Created slice User and Session Slice.
[ 7.025991] systemd[1]: Reached target Slices.
[ 7.040681] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 7.065940] systemd[1]: Started Restore / save the current clock.
[ 7.067709] systemd[1]: Mounted Kernel Debug File System.
[ 7.074679] systemd[1]: Mounted POSIX Message Queue File System.
[ 7.083776] systemd[1]: Started Load Kernel Modules.
[ 7.098922] systemd[1]: Mounting Kernel Configuration File System...
[ 7.105316] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
[ 7.112999] systemd[1]: Starting Apply Kernel Variables...
[ 7.119616] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 7.131534] systemd[1]: Started Remount Root and Kernel File Systems.
[ 7.141399] systemd[1]: Started Nameserver information manager.
[ 7.147930] systemd[1]: Mounted Kernel Configuration File System.
[ 7.162996] systemd[1]: Starting Create System Users...
[ 7.176679] systemd[1]: Starting Load/Save Random Seed...
[ 7.206853] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 7.268221] systemd[1]: Started Apply Kernel Variables.
[ 7.286591] systemd[1]: Started Load/Save Random Seed.
[ 7.329359] systemd[1]: Started Create System Users.
[ 7.342697] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 7.437431] systemd[1]: Started Create Static Device Nodes in /dev.
[ 7.448852] systemd[1]: Starting udev Kernel Device Manager...
[ 7.465697] systemd[1]: Started Set the console keyboard layout.
[ 7.471795] systemd[1]: Reached target Local File Systems (Pre).
[ 7.485281] systemd[1]: Mounting /tmp...
[ 7.502548] systemd[1]: Mounted /tmp.
[ 7.508504] systemd[1]: Reached target Local File Systems.
[ 7.513631] systemd[1]: Condition check resulted in Mark the need to relabel after reboot being skipped.
[ 7.520530] systemd[1]: Starting Armbian ZRAM config...
[ 7.533757] systemd[1]: Starting Set console font and keymap...
[ 7.539153] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[ 7.593787] systemd[1]: Started udev Kernel Device Manager.
[ 7.647820] systemd[1]: Started Set console font and keymap.
[ 7.669049] systemd[1]: Started udev Coldplug all Devices.
[ 7.713099] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
[ 7.739713] systemd[1]: Started Helper to synchronize boot up for ifupdown.
[ 7.753186] systemd[1]: Starting Raise network interfaces...
[ 7.932219] zram: Added device: zram0
[ 7.933932] zram: Added device: zram1
[ 7.935338] zram: Added device: zram2
[ 8.054316] systemd[1]: Found device /dev/ttyS2.
[ 8.131250] zram0: detected capacity change from 0 to 504537088
[ 8.214266] rk3228-codec 12010000.codec: GPIO lookup for consumer spk-en
[ 8.214295] rk3228-codec 12010000.codec: using device tree for GPIO lookup
[ 8.214310] of_get_named_gpiod_flags: can't parse 'spk-en-gpios' property of node '/codec@12010000[0]'
[ 8.214343] of_get_named_gpiod_flags: parsed 'spk-en-gpio' property of node '/codec@12010000[0]' - status (0)
[ 8.214397] rk3228-codec 12010000.codec: spk_depop_time use default value.
[ 8.215292] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound[0]'
[ 8.215316] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound[0]'
[ 8.224454] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '22:00:07', on 'May 6 2021'.
[ 8.238001] mali-utgard 20001000.gpu: mali_platform_device->num_resources = 13
[ 8.238036] mali-utgard 20001000.gpu: resource[0].start = 0x0x20001000
[ 8.238048] mali-utgard 20001000.gpu: resource[1].start = 0x0x20000000
[ 8.238070] mali-utgard 20001000.gpu: resource[2].start = 0x0x20003000
[ 8.238082] mali-utgard 20001000.gpu: resource[3].start = 0x0x20008000
[ 8.238093] mali-utgard 20001000.gpu: resource[4].start = 0x0x20004000
[ 8.238103] mali-utgard 20001000.gpu: resource[5].start = 0x0x2000a000
[ 8.238114] mali-utgard 20001000.gpu: resource[6].start = 0x0x20005000
[ 8.238129] mali-utgard 20001000.gpu: resource[7].start = 0x0x00000020
[ 8.238146] mali-utgard 20001000.gpu: resource[8].start = 0x0x00000021
[ 8.238157] mali-utgard 20001000.gpu: resource[9].start = 0x0x00000022
[ 8.238167] mali-utgard 20001000.gpu: resource[10].start = 0x0x00000021
[ 8.238184] mali-utgard 20001000.gpu: resource[11].start = 0x0x00000022
[ 8.238202] mali-utgard 20001000.gpu: resource[12].start = 0x0x00000021
[ 8.238220] D : [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 623; [Func] : mali_platform_device_init(); to add platform_specific_data to platform_device_of_mali.
[ 8.238599] mali-utgard 20001000.gpu: leakage=4
[ 8.238640] mali-utgard 20001000.gpu: leakage-volt-sel=0
[ 8.238808] mali-utgard 20001000.gpu: Failed to get pvtm
[ 8.239466] mali-utgard 20001000.gpu: avs=0
[ 8.240348] mali-utgard 20001000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
[ 8.241888] asoc-simple-card sound: rk3228-hifi <-> 100b0000.i2s1 mapping ok
[ 8.246923] Mali: Mali device driver loaded
[ 8.251076] Adding 492708k swap on /dev/zram0. Priority:5 extents:1 across:492708k SS
[ 8.336934] devfreq 20001000.gpu: Couldn't update frequency transition information.
[ 8.361630] gpio_ir_recv ir-receiver: GPIO lookup for consumer (null)
[ 8.361663] gpio_ir_recv ir-receiver: using device tree for GPIO lookup
[ 8.361709] of_get_named_gpiod_flags: parsed 'gpios' property of node '/ir-receiver[0]' - status (0)
[ 8.361872] Registered IR keymap rc-rktvbox
[ 8.362182] rc rc1: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1
[ 8.363018] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1/input2
[ 8.437702] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[ 8.438587] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 8.439764] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 8.440044] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 8.440673] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 8.441190] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[ 8.442187] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 8.442632] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 8.570828] systemd[1]: Started Raise network interfaces.
[ 8.578108] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 8.578336] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 8.579253] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 8.579587] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[ 8.580165] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 8.582028] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 8.582285] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[ 8.583278] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 8.616828] ssv6x5x: importing configuration from /lib/firmware/ssv6x5x-wifi.cfg
[ 8.637707] tu_ssv6xxx_sdio_init, probe @af0d0080
[ 8.638260] TU_SSV6XXX_SDIO mmc1:0001:1: Probing SDIO bus
[ 8.638288] ssv6xxx_set_sdio_clk: set sdio clk 25000000Hz
[ 8.638345] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
[ 8.648004] zram1: detected capacity change from 0 to 52428800
[ 8.708137] TU_SSV6XXX_SDIO mmc1:0001:1: vendor = 0x3030 device = 0x3030
[ 8.741333] TU_SSV6XXX_SDIO mmc1:0001:1: dataIOPort 0x10000 regIOPort 0x10020
[ 8.775408] systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ 8.794530] systemd[1]: Started Armbian ZRAM config.
[ 8.803147] TU_SSV6XXX_SDIO mmc1:0001:1: dataIOPort 0x10000 regIOPort 0x10020
[ 8.812960] systemd[1]: Starting Armbian memory supported logging...
[ 8.815160] TU_SSV6XXX_SDIO mmc1:0001:1: CHIP ID: SSV6006C0
[ 8.816086] Attach SSV6006 family HAL function
[ 8.834401] MAC address from e-fuse
[ 8.834433] EFUSE configuration
[ 8.834441] Read efuse chip identity[79000000]
[ 8.834449] r_calbration_result- 0
[ 8.834455] sar_result- 0
[ 8.834461] crystal_frequency_offset- 0
[ 8.834467] tx_power_index_1- 0
[ 8.834474] tx_power_index_2- 0
[ 8.834484] MAC address - 98:c9:7c:3a:d9:d2
[ 8.834490] rate_table_1- 0
[ 8.834497] rate_table_2- 0
[ 8.834582] flash_file /tmp/flash.bin not found
[ 8.834598] ssv6006_if_chk_mac2: is not need to check MAC addres 2 for this model
[ 8.834616] ssv6006_adj_config: use_wpa2_only set to 1, force it to 0
[ 8.834627] ssv6006_adj_config: clear hw beacon
[ 8.853324] RF table ver 20.00 PHY table ver 20.00, common code ver 1.15
[ 8.913932] cfg80211: World regulatory domain updated:
[ 8.913964] cfg80211: DFS Master region: unset
[ 8.913974] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.913988] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.914001] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 8.914011] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.914022] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 8.914034] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 8.914056] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 8.914075] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.914102] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 9.009905] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
[ 9.021621] ieee80211 phy0: Selected rate control algorithm 'ssv_minstrel'
[ 9.022941] ieee80211 phy0: SSV6X5X of iComm-semi
[ 9.023198] ssv6xxx_usb_init
[ 9.023328] usbcore: registered new interface driver SSV6XXX_USB
[ 9.086973] systemd[1]: Starting Load/Save RF Kill Switch Status...
[ 9.093649] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 9.094490] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 9.095052] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 9.095804] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 9.096297] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[ 9.098376] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 9.099690] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 9.100066] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[ 10.055157] systemd[1]: Started Load/Save RF Kill Switch Status.
[ 12.691996] systemd[1]: Started Armbian memory supported logging.
[ 12.704434] systemd[1]: Starting Journal Service...
[ 13.146513] systemd[1]: Started Journal Service.
[ 13.219848] systemd-journald[589]: Received request to flush runtime journal from PID 1### armbian-release:
# PLEASE DO NOT EDIT THIS FILE
BOARD=rk322x-box
BOARD_NAME="rk322x-box"
BOARDFAMILY=rk322x
BUILD_REPOSITORY_URL=git@github.com:armbian/build.git
BUILD_REPOSITORY_COMMIT=4cc754e0b-dirty
DISTRIBUTION_CODENAME=buster
DISTRIBUTION_STATUS=supported
VERSION=21.05.2
LINUXFAMILY=rk322x
ARCH=arm
IMAGE_TYPE=stable
BOARD_TYPE=tvb
INITRD_ARCH=arm
KERNEL_IMAGE_TYPE=Image
BRANCH=legacy### boot environment:
verbosity=1
extraargs=coherent_pool=2M
bootlogo=false
overlay_prefix=rk322x
fdtfile=rk322x-box.dtb
rootdev=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
rootfstype=ext4
overlays=nand led-conf2
usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u### lsusb:
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub### lscpu:
Architecture: armv7l
Byte Order: Little Endian
CPU(s): 4
On-line CPU(s) list: 0-3
Thread(s) per core: 1
Core(s) per socket: 4
Socket(s): 1
Vendor ID: ARM
Model: 5
Model name: Cortex-A7
Stepping: r0p5
CPU max MHz: 1200.0000
CPU min MHz: 408.0000
BogoMIPS: 70.58
Flags: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm### cpuinfo:
processor : 0
model name : ARMv7 Processor rev 5 (v7l)
BogoMIPS : 70.58
Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xc07
CPU revision : 5processor : 1
model name : ARMv7 Processor rev 5 (v7l)
BogoMIPS : 70.58
Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xc07
CPU revision : 5processor : 2
model name : ARMv7 Processor rev 5 (v7l)
BogoMIPS : 70.58
Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xc07
CPU revision : 5processor : 3
model name : ARMv7 Processor rev 5 (v7l)
BogoMIPS : 70.58
Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xc07
CPU revision : 5Hardware : Generic DT based system
Revision : 0000
Serial : 7064501d8f6edfc9### meminfo:
MemTotal: 985420 kB
MemFree: 897640 kB
MemAvailable: 925372 kB
Buffers: 8892 kB
Cached: 30720 kB
SwapCached: 0 kB
Active: 29196 kB
Inactive: 18884 kB
Active(anon): 8796 kB
Inactive(anon): 5700 kB
Active(file): 20400 kB
Inactive(file): 13184 kB
Unevictable: 0 kB
Mlocked: 0 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 985420 kB
LowFree: 897640 kB
SwapTotal: 492708 kB
SwapFree: 492708 kB
Dirty: 184 kB
Writeback: 0 kB
AnonPages: 8624 kB
Mapped: 10088 kB
Shmem: 5792 kB
Slab: 19320 kB
SReclaimable: 10352 kB
SUnreclaim: 8968 kB
KernelStack: 1072 kB
PageTables: 528 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 985416 kB
Committed_AS: 32300 kB
VmallocTotal: 245760 kB
VmallocUsed: 0 kB
VmallocChunk: 0 kB
CmaTotal: 16384 kB
CmaFree: 12208 kB### virtual memory:
vm.admin_reserve_kbytes = 8192
vm.block_dump = 0
vm.dirty_background_bytes = 0
vm.dirty_background_ratio = 10
vm.dirty_bytes = 0
vm.dirty_expire_centisecs = 3000
vm.dirty_ratio = 20
vm.dirtytime_expire_seconds = 43200
vm.dirty_writeback_centisecs = 500
vm.drop_caches = 0
vm.extra_free_kbytes = 0
vm.highmem_is_dirtyable = 0
vm.laptop_mode = 0
vm.legacy_va_layout = 0
vm.lowmem_reserve_ratio = 32 32
vm.max_map_count = 65530
vm.min_free_kbytes = 3924
vm.mmap_min_addr = 32768
vm.mmap_rnd_bits = 8
vm.nr_pdflush_threads = 0
vm.oom_dump_tasks = 1
vm.oom_kill_allocating_task = 0
vm.overcommit_kbytes = 0
vm.overcommit_memory = 0
vm.overcommit_ratio = 50
vm.page-cluster = 0
vm.panic_on_oom = 0
vm.percpu_pagelist_fraction = 0
vm.stat_interval = 1
vm.swappiness = 100
vm.user_reserve_kbytes = 30421
vm.vfs_cache_pressure = 100### ip addr:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 5e:6a:0f:af:62:4f brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 06:5a:0e:81:f7:7c brd ff:ff:ff:ff:ff:ff
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1
link/sit 0.0.0.0 brd 0.0.0.0
5: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 98:c9:7c:3a:d9:d2 brd ff:ff:ff:ff:ff:ff### partitions:
major minor #blocks name
179 0 60620800 mmcblk0
179 1 60010496 mmcblk0p1
253 0 492712 zram0
253 1 51200 zram1### df:
udev 471M 0 471M 0% /dev
tmpfs 97M 2.8M 94M 3% /run
/dev/mmcblk0p1 56G 1.4G 54G 3% /
tmpfs 482M 0 482M 0% /dev/shm
tmpfs 5.0M 4.0K 5.0M 1% /run/lock
tmpfs 482M 0 482M 0% /sys/fs/cgroup
tmpfs 482M 0 482M 0% /tmp
/dev/zram1 49M 1.8M 44M 4% /var/log### lsblk:
NAME FSTYPE SIZE MOUNTPOINT UUID
mmcblk0 57.8G
└─mmcblk0p1 ext4 57.2G / 2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
zram1 50M /var/log### zramctl:
NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT
/dev/zram1 lz4 50M 1.8M 505.8K 824K 4 /var/log
/dev/zram0 lzo 481.2M 4K 76B 4K 4 [SWAP]### mtab:
/dev/mmcblk0p1 / ext4 rw,noatime,errors=remount-ro,commit=600 0 0
/dev/mmcblk0p1 /var/log.hdd ext4 rw,noatime,errors=remount-ro,commit=600 0 0
/dev/zram1 /var/log ext4 rw,relatime,discard 0 0### mmc0:59b4 info:
cid: 1d41445344202020100000003901513f
csd: 400e00325b590001ce7f7f800a4000cf
scr: 0245804300000000
date: 01/2021
name: SD
type: SD
preferred_erase_size: 4194304
fwrev: 0x0
hwrev: 0x1
oemid: 0x4144
manfid: 0x00001d
serial: 0x00000039
uevent: DRIVER=mmcblk MMC_TYPE=SD MMC_NAME=SD MODALIAS=mmc:block
erase_size: 512### Boot system health:
Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St.
07:17:09: 1200MHz 0.60 46% 25% 16% 0% 4% 0% 75.0°C 0/4
07:17:10: 1200MHz 0.60 56% 23% 31% 1% 0% 0% 73.0°C 0/4
07:17:10: 1200MHz 0.60 34% 19% 13% 0% 0% 0% 72.0°C 0/4
07:17:11: 816MHz 0.60 33% 20% 11% 1% 0% 0% 70.0°C 0/4
07:17:11: 1008MHz 0.60 36% 23% 10% 2% 0% 0% 71.0°C 0/4
-
Hi there,
sorry for being late writing, lots of things to do, still need to fin FTDI adapter to read serial, but for now, i was able to boot armbian with "rdkdevicetool ef" with an SD. Some info and some simple benchmarks (with paired or comparative performance cpus), seems that NAND is not detected, only 64GB SD Card from wich Arbmbian is booted. For me its a good candidate for network server where low power is a must (solar powered instalations on mountains), trying to make HA distributed network services (dhcp, radius, php, mariadb, dns, ...). It went little bit hot (/sys/class/thermal/thermal_zone0/temp ) but think it is not reading real temp, as it does not get lower than 70° and went up to 91° while benchmarking but box was not so hot on hand touch.
MXQ PRO 4K 5G, announced with 4GB Ram and 32GB Rom, Rk3229 and eMMC, finally, it has: 1GB RAM, 8GB NAND (unuseable for now), RK3228A:
lshw
server1
description: ARMv7 Processor rev 5 (v7l)
product: Generic RK322x TV Box board
serial: 7064501d8f6edfc9
width: 32 bits
capabilities: smp
*-core
description: Motherboard
physical id: 0
*-cpu:0
description: CPU
product: cpu
physical id: 0
bus info: cpu@0
size: 1200MHz
capacity: 1200MHz
capabilities: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm cpufreq
*-cpu:1
description: CPU
product: cpu
physical id: 1
bus info: cpu@1
size: 1200MHz
capacity: 1200MHz
capabilities: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm cpufreq
*-cpu:2
description: CPU
product: cpu
physical id: 2
bus info: cpu@2
size: 1200MHz
capacity: 1200MHz
capabilities: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm cpufreq
*-cpu:3
description: CPU
product: cpu
physical id: 3
bus info: cpu@3
size: 1200MHz
capacity: 1200MHz
capabilities: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm cpufreq
*-memory
description: System memory
physical id: 4
size: 962MiB
*-usbhost:0
product: Generic Platform OHCI controller
vendor: Linux 4.4.194-rk322x ohci_hcd
physical id: 2
bus info: usb@7
logical name: usb7
version: 4.04
capabilities: usb-1.10
configuration: driver=hub slots=1 speed=12Mbit/s
*-usbhost:1
product: Generic Platform OHCI controller
vendor: Linux 4.4.194-rk322x ohci_hcd
physical id: 3
bus info: usb@6
logical name: usb6
version: 4.04
capabilities: usb-1.10
configuration: driver=hub slots=1 speed=12Mbit/s
*-usbhost:2
product: Generic Platform OHCI controller
vendor: Linux 4.4.194-rk322x ohci_hcd
physical id: 4
bus info: usb@5
logical name: usb5
version: 4.04
capabilities: usb-1.10
configuration: driver=hub slots=1 speed=12Mbit/s
*-usbhost:3
product: EHCI Host Controller
vendor: Linux 4.4.194-rk322x ehci_hcd
physical id: 5
bus info: usb@4
logical name: usb4
version: 4.04
capabilities: usb-2.00
configuration: driver=hub slots=1 speed=480Mbit/s
*-usbhost:4
product: EHCI Host Controller
vendor: Linux 4.4.194-rk322x ehci_hcd
physical id: 6
bus info: usb@3
logical name: usb3
version: 4.04
capabilities: usb-2.00
configuration: driver=hub slots=1 speed=480Mbit/s
*-usbhost:5
product: EHCI Host Controller
vendor: Linux 4.4.194-rk322x ehci_hcd
physical id: 7
bus info: usb@2
logical name: usb2
version: 4.04
capabilities: usb-2.00
configuration: driver=hub slots=1 speed=480Mbit/s
*-usbhost:6
product: DWC OTG Controller
vendor: Linux 4.4.194-rk322x dwc2_hsotg
physical id: 1
bus info: usb@1
logical name: usb1
version: 4.04
capabilities: usb-2.00
configuration: driver=hub slots=1 speed=480Mbit/s
*-network:0
description: Wireless interface
physical id: 8
logical name: wlan0
serial: 98:c9:7c:3a:d9:d2
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=ssv6x5x driverversion=4.4.194-rk322x firmware=N/A link=no multicast=yes wireless=IEEE 802.11abgn
*-network:1 DISABLED
description: Ethernet interface
physical id: 9
logical name: dummy0
serial: 8a:92:1d:67:3d:b2
capabilities: ethernet physical
configuration: broadcast=yes driver=dummy driverversion=1.0
*-network:2
description: Ethernet interface
physical id: a
logical name: docker0
serial: 02:42:39:76:24:61
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A ip=172.17.0.1 link=no multicast=yes
*-network:3
description: Ethernet interface
physical id: b
logical name: eth0
serial: 06:5a:0e:81:f7:7c
size: 100Mbit/s
capacity: 100Mbit/s
capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=st_gmac driverversion=March_2013 duplex=full ip=172.16.5.26 link=yes multicast=yes port=MII speed=100Mbit/s
lscpu
Architecture: armv7l
Byte Order: Little Endian
CPU(s): 4
On-line CPU(s) list: 0-3
Thread(s) per core: 1
Core(s) per socket: 4
Socket(s): 1
Vendor ID: ARM
Model: 5
Model name: Cortex-A7
Stepping: r0p5
CPU max MHz: 1200.0000
CPU min MHz: 408.0000
BogoMIPS: 35.29
Flags: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 57.8G 0 disk
└─mmcblk0p1 179:1 0 57.2G 0 part /
zram0 253:0 0 481.2M 0 disk [SWAP]
zram1 253:1 0 50M 0 disk /var/log-CPU Blowfish-
Rk3228A 4x 1200.00 MHz 12.23
Intel(R) Pentium(R) 4 CPU 3.20GHz 2x 3200.00 MHz 12.06
-CPU CryptoHash-
Rk3228A 4x 1200.00 MHz 105.23
Intel(R) Atom(TM) CPU330 @ 1.60GHz 4x 1596.00 MHz 105.57
Intel(R) Core(TM)2 Duo CPU P7350@ 2.00GHz 2x 2000.00 MHz 103.95
-CPU Fibonacci-
Rk3228A 4x 1200.00 MHz 3.40
AMD Phenom(tm) 9150e Quad-Core Processor 4x 900.00 MHz 3.28
Intel(R) Core(TM)2 Quad CPUQ6700@ 2.66GHz 4x 2669.00 MHz 3.54
-CPU N-Queens-
Rk3228A 4x 1200.00 MHz 18.34
Intel(R) Core(TM)2 Quad CPUQ9400@ 2.66GHz 4x 2003.00 MHz 18.25
-FPU FFT-
Rk3228A 4x 1200.00 MHz 14.10
Intel(R) Pentium(R) M processor 1600MHz 1x 1600.00 MHz 13.50
-FPU Raytracing-
Rk3228A 4x 1200.00 MHz 9.56
AMD Athlon(tm) 64 X2 Dual Core Processor 6400+ 2x 1000.00 MHz 10.93
-
Hi,
@jock Multitool and Libreelec boot correctly, and both show 980MB RAM, so yes, it has 1GB available.
rdkdeveltool detects NAND as SAMSUNG with 7301MB.
@fabiobassa just tell me what can be helpfull and will do and post about it. Need to look for any of the USB-Uart devices i should have somewhere
Im unable to boot Armbian.
Multitool boots but any option says that eMMC is not detected, so nothing to do there.
I used Usb OTG option, so i went and wrote u-boot img to 0x4000 with rdkdeveltool (i made a backup before), and tried different armbian images (focal and buster with 4.4 and the one with 5.10) to boot, on SDCard reader, on OTG usb with reader, but nothing boots. Still multool boots ok, but no eMMC detected, stock android is no more loading. Original Firmware and/or NAND data is not important for me, i would like to boot from SD and work there, as i'm looking for cheap low power simple task server (No UI, no GPU, no wifi, just ethernet, cpu and ram), but dont know what else to try.
Any suggestions ? Maybe i should try to
Best Regards,
Beretas
-
Hi there,
hope everyone is ok. I have learned a lot from this forum, and think its time to help/share on something. Just got new boxes and want to share info with you and im open to try/test whatever is needed. So:
MXQ Pro 4K 5G Android TV Box, 4Gb Ram, 32Gb Rom, 20 USD
Board: R329Q_V8.1 2020.06.15
Processor on stick: RK3229, under the heatskin: RK3228A
RAM: 4Gb, 4x Hynx H5TC2G43BFR-H9A (DDR3L 1333 Cl9-9-9) (it is supposed that each one should be 2Gb is what SK Hynx tells about this serial, each 4x512Mb)
ROM: 32Gb, RQueenston K9GCGD8U0F (cant find anything about it, seems like Samsung NAND PN, stick says eMMC)
Wifi: SV6256P, Dual Band 802.11 a/b/g/n
Will try to play with it today, and see what i can do, will post about it later.
Images (cant attach them):
https://ibb.co/6s2kpFQ
https://ibb.co/dW9TqwZ
https://ibb.co/YNJcZBh
https://ibb.co/4fdf3BY
https://ibb.co/5GwK1HP
https://ibb.co/w4M12HJ
https://ibb.co/W6SfX9t
https://ibb.co/9hHPGDd
https://ibb.co/F4MnfH6
CSC Armbian for RK322x TV box boards
in Rockchip CPU Boxes
Posted
@jock
don't know if i did it as it should, but upgrade_tool was giving me an error:
upgrade_tool ul rk322x_loader_v1.10.256.bin
Not found config.ini
Program Data in /home/me/rkbin/tools
Loading loader...
Support Type:RK322A Loader ver:2.56 Loader Time:2021-03-13 16:06:57
Prepare IDB Fail
so checked:
rkdeveloptool ld
DevNo=1 Vid=0x2207,Pid=0x320b,LocationID=301 Maskrom
and did:
rkdeveloptool ul rk322x_loader_v1.10.256.bin
Upgrading loader succeeded.
armbianmonitor -U
1
2 ### Activated 1 lzo zram swap devices with 481 MB each
3
4 ### Activated Armbian ramlog partition with lz4 compression
5
6 ### Activated lzo compressed /tmp
7
8 Fri 07 May 2021 08:24:09 PM UTC | rk322x-box | 21.05.1 | armhf | armv7l | 4.4.194-rk322x
9
10 ### dmesg:
11
12 [ 0.000000] Booting Linux on physical CPU 0xf00
13 [ 0.000000] Initializing cgroup subsys cpuset
14 [ 0.000000] Initializing cgroup subsys cpu
15 [ 0.000000] Initializing cgroup subsys cpuacct
16 [ 0.000000] Linux version 4.4.194-rk322x (root@hirsute) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) ) #3 SMP Thu May 6 22:00:38 UTC 2021
17 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
18 [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
19 [ 0.000000] Machine model: Generic RK322x TV Box board
20 [ 0.000000] cma: Reserved 16 MiB at 0x9f000000
21 [ 0.000000] Memory policy: Data cache writealloc
22 [ 0.000000] On node 0 totalpages: 253952
23 [ 0.000000] free_area_init_node: node 0, pgdat b1253b40, node_mem_map ee6f1000
24 [ 0.000000] Normal zone: 2304 pages used for memmap
25 [ 0.000000] Normal zone: 0 pages reserved
26 [ 0.000000] Normal zone: 253952 pages, LIFO batch:31
27 [ 0.000000] psci: probing for conduit method from DT.
28 [ 0.000000] psci: PSCIv1.0 detected in firmware.
29 [ 0.000000] psci: Using standard PSCI v0.2 function IDs
30 [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
31 [ 0.000000] PERCPU: Embedded 14 pages/cpu @ee68f000 s24856 r8192 d24296 u57344
32 [ 0.000000] pcpu-alloc: s24856 r8192 d24296 u57344 alloc=14*4096
33 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
34 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251648
35 [ 0.000000] Kernel command line: earlyprintk root=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db console=ttyS2,115200n8 console=tty1 rootwait rootfstype=ext4 consoleblank=0 loglevel=1 ubootpart=73c5b759-01 usb-storage.quirks= coherent_pool=2M cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
36 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
37 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
38 [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
39 [ 0.000000] Memory: 962664K/1015808K available (12862K kernel code, 919K rwdata, 3240K rodata, 808K init, 1219K bss, 36760K reserved, 16384K cma-reserved, 0K highmem)
40 [ 0.000000] Virtual kernel memory layout:
41 vector : 0xffff0000 - 0xffff1000 ( 4 kB)
42 fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
43 vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
44 lowmem : 0xb0000000 - 0xf0000000 (1024 MB)
45 pkmap : 0xafe00000 - 0xb0000000 ( 2 MB)
46 modules : 0xaf000000 - 0xafe00000 ( 14 MB)
47 .text : 0xb0008000 - 0xb0c97c6c (12864 kB)
48 .init : 0xb10b0000 - 0xb117a000 ( 808 kB)
49 .data : 0xb117a000 - 0xb125fe94 ( 920 kB)
50 .bss : 0xb1261000 - 0xb1391f14 (1220 kB)
51 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
52 [ 0.000000] Hierarchical RCU implementation.
53 [ 0.000000] Build-time adjustment of leaf fanout to 32.
54 [ 0.000000] NR_IRQS:16 nr_irqs:16 16
55 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
56 [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
57 [ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
58 [ 0.000022] Switching to timer-based delay loop, resolution 41ns
59 [ 0.001779] Console: colour dummy device 80x30
60 [ 0.001962] console [tty1] enabled
61 [ 0.001987] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
62 [ 0.002005] pid_max: default: 32768 minimum: 301
63 [ 0.002135] Security Framework initialized
64 [ 0.002148] Yama: becoming mindful.
65 [ 0.002223] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
66 [ 0.002239] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
67 [ 0.003122] Initializing cgroup subsys io
68 [ 0.003156] Initializing cgroup subsys memory
69 [ 0.003198] Initializing cgroup subsys devices
70 [ 0.003218] Initializing cgroup subsys freezer
71 [ 0.003235] Initializing cgroup subsys net_cls
72 [ 0.003253] Initializing cgroup subsys perf_event
73 [ 0.003270] Initializing cgroup subsys net_prio
74 [ 0.003299] Initializing cgroup subsys pids
75 [ 0.003366] CPU: Testing write buffer coherency: ok
76 [ 0.003413] ftrace: allocating 41892 entries in 123 pages
77 [ 0.082701] /cpus/cpu@f00 missing clock-frequency property
78 [ 0.082733] /cpus/cpu@f01 missing clock-frequency property
79 [ 0.082751] /cpus/cpu@f02 missing clock-frequency property
80 [ 0.082771] /cpus/cpu@f03 missing clock-frequency property
81 [ 0.082783] CPU0: update cpu_capacity 430
82 [ 0.082794] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
83 [ 0.082880] Setting up static identity map for 0x60008280 - 0x600082d8
84 [ 0.094092] CPU1: update cpu_capacity 430
85 [ 0.094100] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
86 [ 0.103560] CPU2: update cpu_capacity 430
87 [ 0.103569] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
88 [ 0.113014] CPU3: update cpu_capacity 430
89 [ 0.113022] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
90 [ 0.113160] Brought up 4 CPUs
91 [ 0.113199] SMP: Total of 4 processors activated (192.00 BogoMIPS).
92 [ 0.113207] CPU: All CPU(s) started in SVC mode.
93 [ 0.114723] devtmpfs: initialized
94 [ 0.134213] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
95 [ 0.134801] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
96 [ 0.134840] futex hash table entries: 1024 (order: 4, 65536 bytes)
97 [ 0.136177] xor: measuring software checksum speed
98 [ 0.174729] arm4regs : 1011.000 MB/sec
99 [ 0.214834] 8regs : 705.000 MB/sec
100 [ 0.254937] 32regs : 684.000 MB/sec
101 [ 0.295037] neon : 1018.000 MB/sec
102 [ 0.295047] xor: using function: neon (1018.000 MB/sec)
103 [ 0.295089] pinctrl core: initialized pinctrl subsystem
104 [ 0.296629] NET: Registered protocol family 16
105 [ 0.299160] DMA: preallocated 2048 KiB pool for atomic coherent allocations
106 [ 0.311190] cpuidle: using governor ladder
107 [ 0.323205] cpuidle: using governor menu
108 [ 0.339880] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0
109 [ 0.340041] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1
110 [ 0.340194] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2
111 [ 0.340355] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3
112 [ 0.346585] console [pstore-1] enabled
113 [ 0.346596] pstore: Registered ramoops as persistent store backend
114 [ 0.346608] ramoops: attached 0xf0000@0x62e00000, ecc: 0/0
115 [ 0.349934] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
116 [ 0.349954] hw-breakpoint: maximum watchpoint size is 8 bytes.
117 [ 0.350174] sip_firmware_init: set rockchip sip version v2 failed
118 [ 0.448055] raid6: int32x1 gen() 133 MB/s
119 [ 0.516169] raid6: int32x1 xor() 131 MB/s
120 [ 0.584392] raid6: int32x2 gen() 166 MB/s
121 [ 0.652660] raid6: int32x2 xor() 137 MB/s
122 [ 0.720808] raid6: int32x4 gen() 163 MB/s
123 [ 0.789056] raid6: int32x4 xor() 137 MB/s
124 [ 0.857209] raid6: int32x8 gen() 166 MB/s
125 [ 0.925467] raid6: int32x8 xor() 113 MB/s
126 [ 0.993597] raid6: neonx1 gen() 382 MB/s
127 [ 1.061712] raid6: neonx1 xor() 290 MB/s
128 [ 1.129929] raid6: neonx2 gen() 519 MB/s
129 [ 1.198064] raid6: neonx2 xor() 376 MB/s
130 [ 1.266274] raid6: neonx4 gen() 581 MB/s
131 [ 1.334481] raid6: neonx4 xor() 400 MB/s
132 [ 1.402677] raid6: neonx8 gen() 559 MB/s
133 [ 1.470929] raid6: neonx8 xor() 391 MB/s
134 [ 1.470941] raid6: using algorithm neonx4 gen() 581 MB/s
135 [ 1.470951] raid6: .... xor() 400 MB/s, rmw enabled
136 [ 1.470962] raid6: using intx1 recovery algorithm
137 [ 1.471951] rockchip-pm rockchip-suspend: not set wakeup-config
138 [ 1.471975] rockchip-pm rockchip-suspend: not set pwm-regulator-config
139 [ 1.472341] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@0[0]'
140 [ 1.472830] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@1[0]'
141 [ 1.473453] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc-host-regulator[0]' - status (0)
142 [ 1.474050] of_get_named_gpiod_flags: parsed 'gpio' property of node '/otg-vbus-regulator[0]' - status (0)
143 [ 1.474556] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]'
144 [ 1.475466] iommu: Adding device 20020000.vpu-service to group 0
145 [ 1.475573] iommu: Adding device 20030000.rkvdec to group 1
146 [ 1.475669] iommu: Adding device 20050000.vop to group 2
147 [ 1.475761] iommu: Adding device 20070000.iep to group 3
148 [ 1.476298] rk_iommu 20020800.iommu: can't get sclk
149 [ 1.476889] rk_iommu 20030480.iommu: can't get sclk
150 [ 1.477137] rk_iommu 20053f00.iommu: can't get sclk
151 [ 1.477282] rk_iommu 20070800.iommu: can't get aclk
152 [ 1.477301] rk_iommu 20070800.iommu: can't get hclk
153 [ 1.477317] rk_iommu 20070800.iommu: can't get sclk
154 [ 1.478063] SCSI subsystem initialized
155 [ 1.478478] usbcore: registered new interface driver usbfs
156 [ 1.478577] usbcore: registered new interface driver hub
157 [ 1.478693] usbcore: registered new device driver usb
158 [ 1.478969] media: Linux media interface: v0.10
159 [ 1.479076] Linux video capture interface: v2.00
160 [ 1.479329] pps_core: LinuxPPS API ver. 1 registered
161 [ 1.479345] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
162 [ 1.479387] PTP clock support registered
163 [ 1.481295] Advanced Linux Sound Architecture Driver Initialized.
164 [ 1.482283] Bluetooth: Core ver 2.21
165 [ 1.482350] NET: Registered protocol family 31
166 [ 1.482364] Bluetooth: HCI device and connection manager initialized
167 [ 1.482385] Bluetooth: HCI socket layer initialized
168 [ 1.482403] Bluetooth: L2CAP socket layer initialized
169 [ 1.482456] Bluetooth: SCO socket layer initialized
170 [ 1.483263] NetLabel: Initializing
171 [ 1.483285] NetLabel: domain hash size = 128
172 [ 1.483294] NetLabel: protocols = UNLABELED CIPSOv4
173 [ 1.483367] NetLabel: unlabeled traffic allowed by default
174 [ 1.484706] clocksource: Switched to clocksource arch_sys_counter
175 [ 1.579545] NET: Registered protocol family 2
176 [ 1.580387] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
177 [ 1.580503] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
178 [ 1.580940] TCP: Hash tables configured (established 8192 bind 8192)
179 [ 1.581043] UDP hash table entries: 512 (order: 2, 24576 bytes)
180 [ 1.581113] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
181 [ 1.581465] NET: Registered protocol family 1
182 [ 1.582099] RPC: Registered named UNIX socket transport module.
183 [ 1.582122] RPC: Registered udp transport module.
184 [ 1.582133] RPC: Registered tcp transport module.
185 [ 1.582143] RPC: Registered tcp NFSv4.1 backchannel transport module.
186 [ 1.582467] Trying to unpack rootfs image as initramfs...
187 [ 1.955293] Freeing initrd memory: 5564K
188 [ 1.956316] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
189 [ 1.959287] Initialise system trusted keyring
190 [ 1.973170] VFS: Disk quotas dquot_6.6.0
191 [ 1.973484] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
192 [ 1.976164] squashfs: version 4.0 (2009/01/31) Phillip Lougher
193 [ 1.979591] NFS: Registering the id_resolver key type
194 [ 1.979662] Key type id_resolver registered
195 [ 1.979674] Key type id_legacy registered
196 [ 1.979709] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
197 [ 1.979818] ntfs: driver 2.1.32 [Flags: R/W].
198 [ 1.980867] JFS: nTxBlock = 7692, nTxLock = 61538
199 [ 1.989484] SGI XFS with security attributes, no debug enabled
200 [ 1.998636] NET: Registered protocol family 38
201 [ 1.998688] Key type asymmetric registered
202 [ 1.998708] Asymmetric key parser 'x509' registered
203 [ 1.999105] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
204 [ 1.999503] io scheduler noop registered
205 [ 1.999534] io scheduler deadline registered
206 [ 1.999617] io scheduler cfq registered (default)
207 [ 2.002806] phy phy-11000000.syscon:usb2-phy@800.2: Failed to get VBUS supply regulator
208 [ 2.007885] rk-vcodec 20020000.vpu-service: no regulator for vcodec
209 [ 2.008286] rk-vcodec 20020000.vpu-service: probe device
210 [ 2.008741] rk-vcodec 20020000.vpu-service: drm allocator with mmu enabled
211 [ 2.009933] rk-vcodec 20020000.vpu-service: could not find power_model node
212 [ 2.009958] rk-vcodec 20020000.vpu-service: init success
213 [ 2.010276] rk-vcodec 20030000.rkvdec: vcodec regulator not ready, retry
214 [ 2.014549] dma-pl330 110f0000.pdma: Loaded driver for PL330 DMAC-241330
215 [ 2.014579] dma-pl330 110f0000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
216 [ 2.015700] rockchip-system-monitor rockchip-system-monitor: system monitor probe
217 [ 2.016181] pwm-regulator vdd-arm-regulator: GPIO lookup for consumer enable
218 [ 2.016201] pwm-regulator vdd-arm-regulator: using device tree for GPIO lookup
219 [ 2.016218] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-arm-regulator[0]'
220 [ 2.016233] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-arm-regulator[0]'
221 [ 2.016247] pwm-regulator vdd-arm-regulator: using lookup tables for GPIO lookup
222 [ 2.016262] pwm-regulator vdd-arm-regulator: lookup for GPIO enable failed
223 [ 2.016983] pwm-regulator vdd-log-regulator: GPIO lookup for consumer enable
224 [ 2.017005] pwm-regulator vdd-log-regulator: using device tree for GPIO lookup
225 [ 2.017021] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log-regulator[0]'
226 [ 2.017036] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log-regulator[0]'
227 [ 2.017049] pwm-regulator vdd-log-regulator: using lookup tables for GPIO lookup
228 [ 2.017065] pwm-regulator vdd-log-regulator: lookup for GPIO enable failed
229 [ 2.018107] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
230 [ 2.018893] 11030000.serial: ttyS2 at MMIO 0x11030000 (irq = 30, base_baud = 1500000) is a 16550A
231 [ 2.019718] console [ttyS2] enabled
232 [ 2.021574] [drm] Initialized drm 1.1.0 20060810
233 [ 2.024025] [drm] Rockchip DRM driver version: v1.0.1
234 [ 2.024262] rockchip-drm display-subsystem: devfreq is not set
235 [ 2.025076] rockchip-drm display-subsystem: bound 20050000.vop (ops 0xb0d1b2b0)
236 [ 2.025464] i2c i2c-0: of_i2c: modalias failure on /hdmi@200a0000/ports
237 [ 2.025491] dwhdmi-rockchip 200a0000.hdmi: registered DesignWare HDMI I2C bus driver
238 [ 2.025601] dwhdmi-rockchip 200a0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (inno_dw_hdmi_phy)
239 [ 2.026868] rockchip-drm display-subsystem: bound 200a0000.hdmi (ops 0xb0d13808)
240 [ 2.026893] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
241 [ 2.026904] [drm] No driver support for vblank timestamp query.
242 [ 2.027017] rockchip-drm display-subsystem: failed to parse display resources
243 [ 2.649880] rockchip-vop 20050000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p60, type: 11
244 [ 2.650488] dwhdmi-rockchip 200a0000.hdmi: HDMI infoframe: Auxiliary Video Information (AVI), version 2, length 13
245 [ 2.650496] dwhdmi-rockchip 200a0000.hdmi: colorspace: RGB
246 [ 2.650502] dwhdmi-rockchip 200a0000.hdmi: scan mode: Underscan
247 [ 2.650509] dwhdmi-rockchip 200a0000.hdmi: colorimetry: No Data
248 [ 2.650515] dwhdmi-rockchip 200a0000.hdmi: picture aspect: 16:9
249 [ 2.650522] dwhdmi-rockchip 200a0000.hdmi: active aspect: Same as Picture
250 [ 2.650528] dwhdmi-rockchip 200a0000.hdmi: itc: IT Content
251 [ 2.650535] dwhdmi-rockchip 200a0000.hdmi: extended colorimetry: xvYCC 601
252 [ 2.650541] dwhdmi-rockchip 200a0000.hdmi: quantization range: Full
253 [ 2.650547] dwhdmi-rockchip 200a0000.hdmi: nups: Unknown Non-uniform Scaling
254 [ 2.650554] dwhdmi-rockchip 200a0000.hdmi: video code: 16
255 [ 2.650560] dwhdmi-rockchip 200a0000.hdmi: ycc quantization range: Full
256 [ 2.650567] dwhdmi-rockchip 200a0000.hdmi: hdmi content type: Graphics
257 [ 2.650573] dwhdmi-rockchip 200a0000.hdmi: pixel repeat: 0
258 [ 2.650580] dwhdmi-rockchip 200a0000.hdmi: bar top 0, bottom 0, left 0, right 0
259 [ 2.724866] Console: switching to colour frame buffer device 240x67
260 [ 2.774870] rockchip-drm display-subsystem: fb0: frame buffer device
261 [ 2.793287] Registered IR keymap rc-cec
262 [ 2.793539] rc rc0: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0
263 [ 2.794213] input: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0/input0
264 [ 2.796546] brd: module loaded
265 [ 2.808098] loop: module loaded
266 [ 2.808187] lkdtm: No crash points registered, enable through debugfs
267 [ 2.810801] libphy: Fixed MDIO Bus: probed
268 [ 2.810834] tun: Universal TUN/TAP device driver, 1.6
269 [ 2.810846] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
270 [ 2.811181] CAN device driver interface
271 [ 2.812582] rk_gmac-dwmac 30200000.ethernet: clock input or output? (output).
272 [ 2.812610] rk_gmac-dwmac 30200000.ethernet: TX delay(0x30).
273 [ 2.812626] rk_gmac-dwmac 30200000.ethernet: RX delay(0x10).
274 [ 2.812667] rk_gmac-dwmac 30200000.ethernet: integrated PHY? (yes).
275 [ 2.812986] rk_gmac-dwmac 30200000.ethernet: cannot get clock clk_mac_speed
276 [ 2.818073] rk_gmac-dwmac 30200000.ethernet: init for RMII
277 [ 2.852817] stmmac - user ID: 0x10, Synopsys ID: 0x35
278 [ 2.852832] Ring mode enabled
279 [ 2.852843] DMA HW capability register supported
280 [ 2.852852] Normal descriptors
281 [ 2.852864] RX Checksum Offload Engine supported (type 2)
282 [ 2.852874] TX Checksum insertion supported
283 [ 2.852882] Wake-Up On Lan supported
284 [ 2.852978] rk_gmac-dwmac 30200000.ethernet: rk_get_eth_addr: mac address: f6:b4:e0:5a:1e:3a
285 [ 2.852992] eth%d: device MAC address f6:b4:e0:5a:1e:3a
286 [ 2.853001] Enable RX Mitigation via HW Watchdog Timer
287 [ 2.853195] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@30200000[0]' - status (0)
288 [ 3.262396] libphy: stmmac: probed
289 [ 3.262427] eth%d: PHY ID 1234d400 at 0 IRQ POLL (stmmac-0:00) active
290 [ 3.262440] eth%d: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
291 [ 3.262453] eth%d: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
292 [ 3.262466] eth%d: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
293 [ 3.262478] eth%d: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
294 [ 3.262490] eth%d: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
295 [ 3.262503] eth%d: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
296 [ 3.262515] eth%d: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
297 [ 3.262527] eth%d: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
298 [ 3.262540] eth%d: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
299 [ 3.262552] eth%d: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
300 [ 3.262565] eth%d: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
301 [ 3.262577] eth%d: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
302 [ 3.262589] eth%d: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
303 [ 3.262601] eth%d: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
304 [ 3.262614] eth%d: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
305 [ 3.262626] eth%d: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
306 [ 3.262639] eth%d: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
307 [ 3.262651] eth%d: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
308 [ 3.262664] eth%d: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
309 [ 3.262676] eth%d: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
310 [ 3.262688] eth%d: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
311 [ 3.262700] eth%d: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
312 [ 3.262713] eth%d: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
313 [ 3.262725] eth%d: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
314 [ 3.262737] eth%d: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
315 [ 3.262750] eth%d: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
316 [ 3.262762] eth%d: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
317 [ 3.262775] eth%d: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
318 [ 3.262787] eth%d: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
319 [ 3.262799] eth%d: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
320 [ 3.262811] eth%d: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
321 [ 3.264246] PPP generic driver version 2.4.2
322 [ 3.264631] Atmel at76x USB Wireless LAN Driver 0.17 loading
323 [ 3.264845] usbcore: registered new interface driver at76c50x-usb
324 [ 3.264986] usbcore: registered new interface driver rtl8187
325 [ 3.265105] usbcore: registered new interface driver rndis_wlan
326 [ 3.265213] usbcore: registered new interface driver zd1201
327 [ 3.265601] usbcore: registered new interface driver rt2800usb
328 [ 3.265715] Rockchip WiFi SYS interface (V1.00) ...
329 [ 3.265794] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
330 [ 3.265882] usbcore: registered new interface driver pegasus
331 [ 3.265970] usbcore: registered new interface driver rtl8150
332 [ 3.266051] usbcore: registered new interface driver r8152
333 [ 3.266150] usbcore: registered new interface driver asix
334 [ 3.266232] usbcore: registered new interface driver ax88179_178a
335 [ 3.266314] usbcore: registered new interface driver cdc_ether
336 [ 3.266395] usbcore: registered new interface driver dm9601
337 [ 3.266504] usbcore: registered new interface driver smsc75xx
338 [ 3.266609] usbcore: registered new interface driver smsc95xx
339 [ 3.266700] usbcore: registered new interface driver net1080
340 [ 3.266785] usbcore: registered new interface driver rndis_host
341 [ 3.266868] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
342 [ 3.267004] usbcore: registered new interface driver cdc_ncm
343 [ 3.267088] usbcore: registered new interface driver cdc_mbim
344 [ 3.267594] 30040000.usb supply vusb_d not found, using dummy regulator
345 [ 3.267703] 30040000.usb supply vusb_a not found, using dummy regulator
346 [ 3.280924] dwc2 30040000.usb: DWC OTG Controller
347 [ 3.280976] dwc2 30040000.usb: new USB bus registered, assigned bus number 1
348 [ 3.281033] dwc2 30040000.usb: irq 49, io mem 0x30040000
349 [ 3.281387] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
350 [ 3.281406] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
351 [ 3.281421] usb usb1: Product: DWC OTG Controller
352 [ 3.281435] usb usb1: Manufacturer: Linux 4.4.194-rk322x dwc2_hsotg
353 [ 3.281448] usb usb1: SerialNumber: 30040000.usb
354 [ 3.282404] hub 1-0:1.0: USB hub found
355 [ 3.282476] hub 1-0:1.0: 1 port detected
356 [ 3.283996] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
357 [ 3.284024] ehci-platform: EHCI generic platform driver
358 [ 3.286535] ehci-platform 30080000.usb: EHCI Host Controller
359 [ 3.286893] ehci-platform 30080000.usb: new USB bus registered, assigned bus number 2
360 [ 3.287195] ehci-platform 30080000.usb: irq 50, io mem 0x30080000
361 [ 3.296729] ehci-platform 30080000.usb: USB 2.0 started, EHCI 1.00
362 [ 3.297029] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
363 [ 3.297048] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
364 [ 3.297062] usb usb2: Product: EHCI Host Controller
365 [ 3.297076] usb usb2: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
366 [ 3.297090] usb usb2: SerialNumber: 30080000.usb
367 [ 3.298049] hub 2-0:1.0: USB hub found
368 [ 3.298121] hub 2-0:1.0: 1 port detected
369 [ 3.300814] ehci-platform 300c0000.usb: EHCI Host Controller
370 [ 3.301185] ehci-platform 300c0000.usb: new USB bus registered, assigned bus number 3
371 [ 3.301463] ehci-platform 300c0000.usb: irq 52, io mem 0x300c0000
372 [ 3.312728] ehci-platform 300c0000.usb: USB 2.0 started, EHCI 1.00
373 [ 3.313048] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
374 [ 3.313069] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
375 [ 3.313083] usb usb3: Product: EHCI Host Controller
376 [ 3.313097] usb usb3: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
377 [ 3.313110] usb usb3: SerialNumber: 300c0000.usb
378 [ 3.314053] hub 3-0:1.0: USB hub found
379 [ 3.314125] hub 3-0:1.0: 1 port detected
380 [ 3.316811] ehci-platform 30100000.usb: EHCI Host Controller
381 [ 3.317204] ehci-platform 30100000.usb: new USB bus registered, assigned bus number 4
382 [ 3.317504] ehci-platform 30100000.usb: irq 54, io mem 0x30100000
383 [ 3.328726] ehci-platform 30100000.usb: USB 2.0 started, EHCI 1.00
384 [ 3.329020] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
385 [ 3.329040] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
386 [ 3.329054] usb usb4: Product: EHCI Host Controller
387 [ 3.329068] usb usb4: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
388 [ 3.329081] usb usb4: SerialNumber: 30100000.usb
389 [ 3.330064] hub 4-0:1.0: USB hub found
390 [ 3.330145] hub 4-0:1.0: 1 port detected
391 [ 3.330952] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
392 [ 3.331023] ohci-platform: OHCI generic platform driver
393 [ 3.331422] ohci-platform 300a0000.usb: Generic Platform OHCI controller
394 [ 3.331812] ohci-platform 300a0000.usb: new USB bus registered, assigned bus number 5
395 [ 3.332078] ohci-platform 300a0000.usb: irq 51, io mem 0x300a0000
396 [ 3.388987] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
397 [ 3.389011] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
398 [ 3.389026] usb usb5: Product: Generic Platform OHCI controller
399 [ 3.389040] usb usb5: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
400 [ 3.389053] usb usb5: SerialNumber: 300a0000.usb
401 [ 3.390047] hub 5-0:1.0: USB hub found
402 [ 3.390121] hub 5-0:1.0: 1 port detected
403 [ 3.390965] ohci-platform 300e0000.usb: Generic Platform OHCI controller
404 [ 3.391338] ohci-platform 300e0000.usb: new USB bus registered, assigned bus number 6
405 [ 3.391585] ohci-platform 300e0000.usb: irq 53, io mem 0x300e0000
406 [ 3.448990] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
407 [ 3.449014] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
408 [ 3.449029] usb usb6: Product: Generic Platform OHCI controller
409 [ 3.449043] usb usb6: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
410 [ 3.449056] usb usb6: SerialNumber: 300e0000.usb
411 [ 3.449983] hub 6-0:1.0: USB hub found
412 [ 3.450054] hub 6-0:1.0: 1 port detected
413 [ 3.450865] ohci-platform 30120000.usb: Generic Platform OHCI controller
414 [ 3.451214] ohci-platform 30120000.usb: new USB bus registered, assigned bus number 7
415 [ 3.451496] ohci-platform 30120000.usb: irq 55, io mem 0x30120000
416 [ 3.509022] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
417 [ 3.509044] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
418 [ 3.509059] usb usb7: Product: Generic Platform OHCI controller
419 [ 3.509073] usb usb7: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
420 [ 3.509087] usb usb7: SerialNumber: 30120000.usb
421 [ 3.510041] hub 7-0:1.0: USB hub found
422 [ 3.510116] hub 7-0:1.0: 1 port detected
423 [ 3.511018] usbcore: registered new interface driver cdc_acm
424 [ 3.511035] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
425 [ 3.511144] usbcore: registered new interface driver cdc_wdm
426 [ 3.511437] usbcore: registered new interface driver usb-storage
427 [ 3.511619] usbcore: registered new interface driver usbserial
428 [ 3.511709] usbcore: registered new interface driver usbserial_generic
429 [ 3.511772] usbserial: USB Serial support registered for generic
430 [ 3.511881] usbcore: registered new interface driver keyspan
431 [ 3.511941] usbserial: USB Serial support registered for Keyspan - (without firmware)
432 [ 3.511999] usbserial: USB Serial support registered for Keyspan 1 port adapter
433 [ 3.512056] usbserial: USB Serial support registered for Keyspan 2 port adapter
434 [ 3.512112] usbserial: USB Serial support registered for Keyspan 4 port adapter
435 [ 3.512224] usbcore: registered new interface driver option
436 [ 3.512285] usbserial: USB Serial support registered for GSM modem (1-port)
437 [ 3.513083] usbcore: registered new interface driver oti6858
438 [ 3.513153] usbserial: USB Serial support registered for oti6858
439 [ 3.513257] usbcore: registered new interface driver qcserial
440 [ 3.513317] usbserial: USB Serial support registered for Qualcomm USB modem
441 [ 3.513501] usbcore: registered new interface driver sierra
442 [ 3.513562] usbserial: USB Serial support registered for Sierra USB modem
443 [ 3.514940] usbcore: registered new interface driver iforce
444 [ 3.515105] usbcore: registered new interface driver xpad
445 [ 3.515375] usbcore: registered new interface driver usbtouchscreen
446 [ 3.516553] i2c /dev entries driver
447 [ 3.518560] IR NEC protocol handler initialized
448 [ 3.518586] IR RC5(x/sz) protocol handler initialized
449 [ 3.518604] IR RC6 protocol handler initialized
450 [ 3.518621] IR JVC protocol handler initialized
451 [ 3.518638] IR Sony protocol handler initialized
452 [ 3.518655] IR SANYO protocol handler initialized
453 [ 3.518671] IR Sharp protocol handler initialized
454 [ 3.518689] IR MCE Keyboard/mouse protocol handler initialized
455 [ 3.518706] IR XMP protocol handler initialized
456 [ 3.520440] usbcore: registered new interface driver uvcvideo
457 [ 3.520454] USB Video Class driver (1.1.1)
458 [ 3.522438] Boot mode: normal
459 [ 3.523612] rockchip-thermal 11150000.tsadc: tsadc is probed successfully!
460 [ 3.525347] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
461 [ 3.525686] Bluetooth: Virtual HCI driver ver 1.5
462 [ 3.525967] Bluetooth: HCI UART driver ver 2.3
463 [ 3.525986] Bluetooth: HCI UART protocol H4 registered
464 [ 3.525997] Bluetooth: HCI UART protocol LL registered
465 [ 3.526008] Bluetooth: HCI UART protocol ATH3K registered
466 [ 3.526019] Bluetooth: HCI UART protocol Three-wire (H5) registered
467 [ 3.526191] Bluetooth: HCI UART protocol BCM registered
468 [ 3.526342] usbcore: registered new interface driver bfusb
469 [ 3.526486] usbcore: registered new interface driver btusb
470 [ 3.526509] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
471 [ 3.527107] cpu cpu0: leakage=6
472 [ 3.527139] cpu cpu0: leakage-volt-sel=0
473 [ 3.527346] cpu cpu0: Failed to get pvtm
474 [ 3.528790] cpu cpu0: avs=0
475 [ 3.529142] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
476 [ 3.529175] cpu cpu0: failed to read out thermal zone (-22)
477 [ 3.529882] cpu cpu0: failed to find power_model node
478 [ 3.530525] pwrseq_simple sdio-pwrseq: GPIO lookup for consumer reset
479 [ 3.530544] pwrseq_simple sdio-pwrseq: using device tree for GPIO lookup
480 [ 3.530566] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0)
481 [ 3.530918] Synopsys Designware Multimedia Card Interface Driver
482 [ 3.531521] dwmmc_rockchip 30000000.dwmmc: IDMAC supports 32-bit address mode.
483 [ 3.531624] dwmmc_rockchip 30000000.dwmmc: Using internal DMA controller.
484 [ 3.531641] dwmmc_rockchip 30000000.dwmmc: Version ID is 270a
485 [ 3.531702] dwmmc_rockchip 30000000.dwmmc: DW MMC controller at irq 45,32 bit host data width,256 deep fifo
486 [ 3.531783] dwmmc_rockchip 30000000.dwmmc: No vmmc regulator found
487 [ 3.531795] dwmmc_rockchip 30000000.dwmmc: No vqmmc regulator found
488 [ 3.531817] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer cd
489 [ 3.531826] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
490 [ 3.531853] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/dwmmc@30000000[0]' - status (0)
491 [ 3.531888] gpio-49 (cd): gpiod_set_debounce: missing set() or set_debounce() operations
492 [ 3.531899] dwmmc_rockchip 30000000.dwmmc: Got CD GPIO
493 [ 3.531911] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer wp
494 [ 3.531920] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
495 [ 3.531930] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30000000[0]'
496 [ 3.531940] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30000000[0]'
497 [ 3.531949] dwmmc_rockchip 30000000.dwmmc: using lookup tables for GPIO lookup
498 [ 3.531959] dwmmc_rockchip 30000000.dwmmc: lookup for GPIO wp failed
499 [ 3.544783] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
500 [ 3.557691] dwmmc_rockchip 30000000.dwmmc: 1 slots initialized
501 [ 3.558045] dwmmc_rockchip 30010000.dwmmc: num-slots property not found, assuming 1 slot is available
502 [ 3.558129] dwmmc_rockchip 30010000.dwmmc: IDMAC supports 32-bit address mode.
503 [ 3.558228] dwmmc_rockchip 30010000.dwmmc: Using internal DMA controller.
504 [ 3.558246] dwmmc_rockchip 30010000.dwmmc: Version ID is 270a
505 [ 3.558307] dwmmc_rockchip 30010000.dwmmc: DW MMC controller at irq 46,32 bit host data width,256 deep fifo
506 [ 3.558357] dwmmc_rockchip 30010000.dwmmc: No vmmc regulator found
507 [ 3.558368] dwmmc_rockchip 30010000.dwmmc: No vqmmc regulator found
508 [ 3.558387] dwmmc_rockchip 30010000.dwmmc: GPIO lookup for consumer wp
509 [ 3.558397] dwmmc_rockchip 30010000.dwmmc: using device tree for GPIO lookup
510 [ 3.558409] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30010000[0]'
511 [ 3.558419] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30010000[0]'
512 [ 3.558428] dwmmc_rockchip 30010000.dwmmc: using lookup tables for GPIO lookup
513 [ 3.558438] dwmmc_rockchip 30010000.dwmmc: lookup for GPIO wp failed
514 [ 3.558506] dwmmc_rockchip 30010000.dwmmc: allocated mmc-pwrseq
515 [ 3.571289] mmc_host mmc1: Bus speed (slot 0) = 976562Hz (slot req 400000Hz, actual 244140HZ div = 2)
516 [ 3.583981] dwmmc_rockchip 30010000.dwmmc: 1 slots initialized
517 [ 3.584379] dwmmc_rockchip 30020000.dwmmc: IDMAC supports 32-bit address mode.
518 [ 3.584485] dwmmc_rockchip 30020000.dwmmc: Using internal DMA controller.
519 [ 3.584503] dwmmc_rockchip 30020000.dwmmc: Version ID is 270a
520 [ 3.584567] dwmmc_rockchip 30020000.dwmmc: DW MMC controller at irq 47,32 bit host data width,256 deep fifo
521 [ 3.584618] dwmmc_rockchip 30020000.dwmmc: No vmmc regulator found
522 [ 3.584630] dwmmc_rockchip 30020000.dwmmc: No vqmmc regulator found
523 [ 3.584648] dwmmc_rockchip 30020000.dwmmc: GPIO lookup for consumer wp
524 [ 3.584658] dwmmc_rockchip 30020000.dwmmc: using device tree for GPIO lookup
525 [ 3.584670] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30020000[0]'
526 [ 3.584755] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30020000[0]'
527 [ 3.584768] dwmmc_rockchip 30020000.dwmmc: using lookup tables for GPIO lookup
528 [ 3.584856] dwmmc_rockchip 30020000.dwmmc: lookup for GPIO wp failed
529 [ 3.589423] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
530 [ 3.589511] mmc0: new high speed SDXC card at address 59b4
531 [ 3.590261] mmcblk0: mmc0:59b4 SD 57.8 GiB
532 [ 3.591842] mmcblk0: p1
533 [ 3.596776] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
534 [ 3.609278] dwmmc_rockchip 30020000.dwmmc: 1 slots initialized
535 [ 3.610378] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/working[0]' - status (0)
536 [ 3.611509] ledtrig-cpu: registered to indicate activity on CPUs
537 [ 3.611856] hidraw: raw HID events driver (C) Jiri Kosina
538 [ 3.613166] usbcore: registered new interface driver usbhid
539 [ 3.613198] usbhid: USB HID core driver
540 [ 3.614288] ashmem: initialized
541 [ 3.619794] rknandbase v1.2 2018-05-08
542 [ 3.620469] rknand 30030000.nandc: rknand_probe clk rate = 150000000
543 [ 3.621104] ftl_init fffffffe
544 [ 3.621130] rk_ftl_init fail
545 [ 3.623345] usbcore: registered new interface driver snd-usb-audio
546 [ 3.623618] usbcore: registered new interface driver snd-ua101
547 [ 3.623986] usbcore: registered new interface driver snd-usb-caiaq
548 [ 3.624325] usbcore: registered new interface driver snd-usb-6fire
549 [ 3.624608] usbcore: registered new interface driver snd-usb-hiface
550 [ 3.625007] usbcore: registered new interface driver snd-bcd2000
551 [ 3.625239] usbcore: registered new interface driver snd_usb_pod
552 [ 3.625529] usbcore: registered new interface driver snd_usb_podhd
553 [ 3.625743] usbcore: registered new interface driver snd_usb_toneport
554 [ 3.626016] usbcore: registered new interface driver snd_usb_variax
555 [ 3.630762] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
556 [ 3.634004] mmc1: new high speed SDIO card at address 0001
557 [ 3.640960] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
558 [ 3.641612] u32 classifier
559 [ 3.641641] input device check on
560 [ 3.641659] Actions configured
561 [ 3.641701] Netfilter messages via NETLINK v0.30.
562 [ 3.641764] nfnl_acct: registering with nfnetlink.
563 [ 3.641965] nf_conntrack version 0.5.0 (15384 buckets, 61536 max)
564 [ 3.643647] Initializing XFRM netlink socket
565 [ 3.646051] NET: Registered protocol family 10
566 [ 3.648678] ip6_tables: (C) 2000-2006 Netfilter Core Team
567 [ 3.649563] sit: IPv6 over IPv4 tunneling driver
568 [ 3.651343] NET: Registered protocol family 17
569 [ 3.651435] NET: Registered protocol family 15
570 [ 3.651567] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
571 [ 3.651677] Bridge firewalling registered
572 [ 3.651717] can: controller area network core (rev 20120528 abi 9)
573 [ 3.651900] NET: Registered protocol family 29
574 [ 3.651949] can: raw protocol (rev 20120528)
575 [ 3.651986] can: broadcast manager protocol (rev 20120528 t)
576 [ 3.652035] can: netlink gateway (rev 20130117) max_hops=1
577 [ 3.653050] Bluetooth: RFCOMM TTY layer initialized
578 [ 3.653112] Bluetooth: RFCOMM socket layer initialized
579 [ 3.653174] Bluetooth: RFCOMM ver 1.11
580 [ 3.653236] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
581 [ 3.653276] Bluetooth: HIDP socket layer initialized
582 [ 3.653444] 8021q: 802.1Q VLAN Support v1.8
583 [ 3.653533] lib80211: common routines for IEEE802.11 drivers
584 [ 3.653669] lib80211_crypt: registered algorithm 'NULL'
585 [ 3.653722] lib80211_crypt: registered algorithm 'WEP'
586 [ 3.653764] lib80211_crypt: registered algorithm 'CCMP'
587 [ 3.653805] lib80211_crypt: registered algorithm 'TKIP'
588 [ 3.653839] [WLAN_RFKILL]: Enter rfkill_wlan_init
589 [ 3.654367] [BT_RFKILL]: Enter rfkill_rk_init
590 [ 3.654866] Key type dns_resolver registered
591 [ 3.655564] flash vendor_init_thread!
592 [ 3.655600] flash vendor storage:20170308 ret = -1
593 [ 3.655776] Error: Driver 'sc031gs' is already registered, aborting...
594 [ 3.657774] Registering SWP/SWPB emulation handler
595 [ 3.660145] registered taskstats version 1
596 [ 3.660210] Loading compiled-in X.509 certificates
597 [ 3.666633] Btrfs loaded
598 [ 3.668471] rga2: Driver loaded successfully ver:4.01
599 [ 3.668989] rga2: Module initialized.
600 [ 3.669067] pvtm list NULL
601 [ 3.671176] rk-vcodec 20030000.rkvdec: leakage=5
602 [ 3.671236] rk-vcodec 20030000.rkvdec: leakage-volt-sel=0
603 [ 3.671431] rk-vcodec 20030000.rkvdec: Failed to get pvtm
604 [ 3.672284] rk-vcodec 20030000.rkvdec: avs=0
605 [ 3.672970] rk-vcodec 20030000.rkvdec: probe device
606 [ 3.673800] rk-vcodec 20030000.rkvdec: drm allocator with mmu enabled
607 [ 3.676167] rk-vcodec 20030000.rkvdec: init success
608 [ 3.678287] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/hdmi-sound[0]'
609 [ 3.678330] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/hdmi-sound[0]'
610 [ 3.680312] asoc-simple-card hdmi-sound: i2s-hifi <-> 100c0000.i2s0 mapping ok
611 [ 3.683752] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]'
612 [ 3.683794] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]'
613 [ 3.685049] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
614 [ 3.685773] asoc-simple-card spdif-sound: dit-hifi <-> 100d0000.spdif mapping ok
615 [ 3.687928] hctosys: unable to open rtc device (rtc0)
616 [ 3.701531] ALSA device list:
617 [ 3.701557] #0: DW-I2S-HDMI
618 [ 3.701566] #1: SPDIF
619 [ 3.702585] Freeing unused kernel memory: 808K
620 [ 3.702597] This architecture does not have kernel memory protection.
621 [ 3.728900] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
622 [ 3.884792] usb 7-1: new low-speed USB device number 2 using ohci-platform
623 [ 4.089840] usb 7-1: New USB device found, idVendor=04f3, idProduct=0103
624 [ 4.089865] usb 7-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
625 [ 4.099819] input: HID 04f3:0103 as /devices/platform/30120000.usb/usb7/7-1/7-1:1.0/0003:04F3:0103.0001/input/input1
626 [ 4.100977] hid-generic 0003:04F3:0103.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 04f3:0103] on usb-30120000.usb-1/input0
627 [ 4.110398] input: HID 04f3:0103 as /devices/platform/30120000.usb/usb7/7-1/7-1:1.1/0003:04F3:0103.0002/input/input2
628 [ 4.110995] hid-generic 0003:04F3:0103.0002: input,hidraw1: USB HID v1.11 Device [HID 04f3:0103] on usb-30120000.usb-1/input1
629 [ 4.296583] rockchip-vop 20050000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p60, type: 11
630 [ 4.297367] dwhdmi-rockchip 200a0000.hdmi: HDMI infoframe: Auxiliary Video Information (AVI), version 2, length 13
631 [ 4.297388] dwhdmi-rockchip 200a0000.hdmi: colorspace: RGB
632 [ 4.297399] dwhdmi-rockchip 200a0000.hdmi: scan mode: Underscan
633 [ 4.297409] dwhdmi-rockchip 200a0000.hdmi: colorimetry: No Data
634 [ 4.297418] dwhdmi-rockchip 200a0000.hdmi: picture aspect: 16:9
635 [ 4.297427] dwhdmi-rockchip 200a0000.hdmi: active aspect: Same as Picture
636 [ 4.297437] dwhdmi-rockchip 200a0000.hdmi: itc: IT Content
637 [ 4.297446] dwhdmi-rockchip 200a0000.hdmi: extended colorimetry: xvYCC 601
638 [ 4.297456] dwhdmi-rockchip 200a0000.hdmi: quantization range: Full
639 [ 4.297465] dwhdmi-rockchip 200a0000.hdmi: nups: Unknown Non-uniform Scaling
640 [ 4.297474] dwhdmi-rockchip 200a0000.hdmi: video code: 16
641 [ 4.297484] dwhdmi-rockchip 200a0000.hdmi: ycc quantization range: Full
642 [ 4.297493] dwhdmi-rockchip 200a0000.hdmi: hdmi content type: Graphics
643 [ 4.297502] dwhdmi-rockchip 200a0000.hdmi: pixel repeat: 0
644 [ 4.297512] dwhdmi-rockchip 200a0000.hdmi: bar top 0, bottom 0, left 0, right 0
645 [ 4.875166] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
646 [ 5.621861] systemd[1]: System time before build time, advancing clock.
647 [ 5.647052] systemd[1]: Inserted module 'autofs4'
648 [ 5.653466] ip_tables: (C) 2000-2006 Netfilter Core Team
649 [ 5.664336] cgroup: cgroup2: unknown option "nsdelegate"
650 [ 5.681137] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
651 [ 5.682750] systemd[1]: Detected architecture arm.
652 [ 5.697591] systemd[1]: Set hostname to <rk322x-box>.
653 [ 5.926013] ttyS2 - failed to request DMA, use interrupt mode
654 [ 6.049694] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
655 [ 6.049758] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
656 [ 6.490178] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
657 [ 6.504004] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
658 [ 6.508467] systemd[1]: Created slice system-serial\x2dgetty.slice.
659 [ 6.509546] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
660 [ 6.509661] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
661 [ 6.510447] systemd[1]: Listening on Syslog Socket.
662 [ 6.511122] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
663 [ 6.511542] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
664 [ 6.523987] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
665 [ 6.524154] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
666 [ 6.524268] systemd[1]: Reached target Swap.
667 [ 6.525056] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
668 [ 6.526058] systemd[1]: Listening on Journal Socket.
669 [ 6.527248] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
670 [ 6.533047] systemd[1]: Mounting Kernel Debug File System...
671 [ 6.534745] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
672 [ 6.541983] systemd[1]: Starting Create list of required static device nodes for the current kernel...
673 [ 6.544409] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
674 [ 6.545046] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
675 [ 6.552303] systemd[1]: Starting Set the console keyboard layout...
676 [ 6.553537] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
677 [ 6.561849] systemd[1]: Starting Nameserver information manager...
678 [ 6.562972] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
679 [ 6.565151] systemd[1]: Listening on udev Control Socket.
680 [ 6.566760] systemd[1]: Reached target Remote File Systems.
681 [ 6.568101] systemd[1]: Reached target Paths.
682 [ 6.587700] systemd[1]: Starting Restore / save the current clock...
683 [ 6.589796] systemd[1]: Listening on udev Kernel Socket.
684 [ 6.599947] systemd[1]: Starting udev Coldplug all Devices...
685 [ 6.605107] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
686 [ 6.629831] systemd[1]: Starting Load Kernel Modules...
687 [ 6.631984] systemd[1]: Listening on Journal Socket (/dev/log).
688 [ 6.633277] systemd[1]: Reached target Local Encrypted Volumes.
689 [ 6.636298] systemd[1]: Listening on fsck to fsckd communication Socket.
690 [ 6.638256] systemd[1]: Listening on initctl Compatibility Named Pipe.
691 [ 6.649790] systemd[1]: Mounting POSIX Message Queue File System...
692 [ 6.651267] systemd[1]: Reached target System Time Synchronized.
693 [ 6.656409] systemd[1]: Created slice User and Session Slice.
694 [ 6.659160] systemd[1]: Reached target Slices.
695 [ 6.660371] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
696 [ 6.671165] systemd[1]: Starting Remount Root and Kernel File Systems...
697 [ 6.676849] vendor storage:20190527 ret = -1
698 [ 6.696104] systemd[1]: Mounted Kernel Debug File System.
699 [ 6.702431] systemd[1]: Started Create list of required static device nodes for the current kernel.
700 [ 6.728094] systemd[1]: Started Restore / save the current clock.
701 [ 6.730583] systemd[1]: Mounted POSIX Message Queue File System.
702 [ 6.744204] systemd[1]: Started Load Kernel Modules.
703 [ 6.759422] systemd[1]: Started Nameserver information manager.
704 [ 6.763659] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
705 [ 6.772624] systemd[1]: Starting Apply Kernel Variables...
706 [ 6.778356] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
707 [ 6.797687] systemd[1]: Mounting Kernel Configuration File System...
708 [ 6.816782] systemd[1]: Started Remount Root and Kernel File Systems.
709 [ 6.821187] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
710 [ 6.828487] systemd[1]: Starting Load/Save Random Seed...
711 [ 6.861758] systemd[1]: Starting Create System Users...
712 [ 6.879397] systemd[1]: Started Apply Kernel Variables.
713 [ 6.881319] systemd[1]: Mounted Kernel Configuration File System.
714 [ 6.959097] systemd[1]: Started Load/Save Random Seed.
715 [ 7.081052] systemd[1]: Started Set the console keyboard layout.
716 [ 7.138365] systemd[1]: Started Create System Users.
717 [ 7.145541] systemd[1]: Starting Create Static Device Nodes in /dev...
718 [ 7.217529] systemd[1]: Started Create Static Device Nodes in /dev.
719 [ 7.218879] systemd[1]: Reached target Local File Systems (Pre).
720 [ 7.225893] systemd[1]: Mounting /tmp...
721 [ 7.234095] systemd[1]: Starting udev Kernel Device Manager...
722 [ 7.247948] systemd[1]: Mounted /tmp.
723 [ 7.249641] systemd[1]: Reached target Local File Systems.
724 [ 7.257763] systemd[1]: Starting Armbian ZRAM config...
725 [ 7.259121] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
726 [ 7.267847] systemd[1]: Starting Set console font and keymap...
727 [ 7.293094] systemd[1]: Starting Mark the need to relabel after reboot...
728 [ 7.306834] systemd[1]: Started udev Coldplug all Devices.
729 [ 7.320573] systemd[1]: Started Mark the need to relabel after reboot.
730 [ 7.332500] systemd[1]: Started Set console font and keymap.
731 [ 7.353978] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
732 [ 7.387568] systemd[1]: Started Helper to synchronize boot up for ifupdown.
733 [ 7.403454] systemd[1]: Starting Raise network interfaces...
734 [ 7.433969] random: nonblocking pool is initialized
735 [ 7.477712] systemd[1]: Started udev Kernel Device Manager.
736 [ 7.573129] zram: Added device: zram0
737 [ 7.578812] zram: Added device: zram1
738 [ 7.585451] zram: Added device: zram2
739 [ 7.841365] zram0: detected capacity change from 0 to 504537088
740 [ 7.901782] systemd[1]: Found device /dev/ttyS2.
741 [ 7.917606] rk3228-codec 12010000.codec: GPIO lookup for consumer spk-en
742 [ 7.917649] rk3228-codec 12010000.codec: using device tree for GPIO lookup
743 [ 7.917690] of_get_named_gpiod_flags: can't parse 'spk-en-gpios' property of node '/codec@12010000[0]'
744 [ 7.917749] of_get_named_gpiod_flags: parsed 'spk-en-gpio' property of node '/codec@12010000[0]' - status (0)
745 [ 7.917848] rk3228-codec 12010000.codec: spk_depop_time use default value.
746 [ 7.919527] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound[0]'
747 [ 7.919580] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound[0]'
748 [ 7.920420] Adding 492708k swap on /dev/zram0. Priority:5 extents:1 across:492708k SS
749 [ 7.945367] asoc-simple-card sound: rk3228-hifi <-> 100b0000.i2s1 mapping ok
750 [ 7.959856] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '22:00:07', on 'May 6 2021'.
751 [ 7.960233] mali-utgard 20001000.gpu: mali_platform_device->num_resources = 13
752 [ 7.960263] mali-utgard 20001000.gpu: resource[0].start = 0x0x20001000
753 [ 7.960277] mali-utgard 20001000.gpu: resource[1].start = 0x0x20000000
754 [ 7.960288] mali-utgard 20001000.gpu: resource[2].start = 0x0x20003000
755 [ 7.960298] mali-utgard 20001000.gpu: resource[3].start = 0x0x20008000
756 [ 7.960310] mali-utgard 20001000.gpu: resource[4].start = 0x0x20004000
757 [ 7.960320] mali-utgard 20001000.gpu: resource[5].start = 0x0x2000a000
758 [ 7.960330] mali-utgard 20001000.gpu: resource[6].start = 0x0x20005000
759 [ 7.960364] mali-utgard 20001000.gpu: resource[7].start = 0x0x00000020
760 [ 7.960393] mali-utgard 20001000.gpu: resource[8].start = 0x0x00000021
761 [ 7.960417] mali-utgard 20001000.gpu: resource[9].start = 0x0x00000022
762 [ 7.960430] mali-utgard 20001000.gpu: resource[10].start = 0x0x00000021
763 [ 7.960442] mali-utgard 20001000.gpu: resource[11].start = 0x0x00000022
764 [ 7.960453] mali-utgard 20001000.gpu: resource[12].start = 0x0x00000021
765 [ 7.960467] D : [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 623; [Func] : mali_platform_device_init(); to add platform_specific_data to platform_device_of_mali.
766 [ 7.967250] mali-utgard 20001000.gpu: leakage=5
767 [ 7.967292] mali-utgard 20001000.gpu: leakage-volt-sel=0
768 [ 7.967471] mali-utgard 20001000.gpu: Failed to get pvtm
769 [ 7.968147] mali-utgard 20001000.gpu: avs=0
770 [ 7.974575] mali-utgard 20001000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
771 [ 8.012095] Mali: Mali device driver loaded
772 [ 8.072922] devfreq 20001000.gpu: Couldn't update frequency transition information.
773 [ 8.207670] gpio_ir_recv ir-receiver: GPIO lookup for consumer (null)
774 [ 8.207704] gpio_ir_recv ir-receiver: using device tree for GPIO lookup
775 [ 8.207759] of_get_named_gpiod_flags: parsed 'gpios' property of node '/ir-receiver[0]' - status (0)
776 [ 8.207911] Registered IR keymap rc-rktvbox
777 [ 8.208213] rc rc1: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1
778 [ 8.209167] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1/input3
779 [ 8.485667] systemd[1]: Started Raise network interfaces.
780 [ 8.674338] zram1: detected capacity change from 0 to 52428800
781 [ 8.758278] cfg80211: World regulatory domain updated:
782 [ 8.758296] cfg80211: DFS Master region: unset
783 [ 8.758297] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
784 [ 8.758311] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
785 [ 8.758320] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
786 [ 8.758324] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
787 [ 8.758330] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
788 [ 8.758338] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
789 [ 8.758343] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
790 [ 8.758348] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
791 [ 8.758352] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
792 [ 8.830930] zram2: detected capacity change from 0 to 504537088
793 [ 8.888281] systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
794 [ 8.906424] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
795 [ 8.907888] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
796 [ 8.908302] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
797 [ 8.909136] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
798 [ 8.909557] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
799 [ 8.911107] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
800 [ 8.912024] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
801 [ 8.912929] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
802 [ 8.915473] EXT4-fs (zram2): mounted filesystem without journal. Opts: discard
803 [ 8.955804] systemd[1]: Started Armbian ZRAM config.
804 [ 8.974142] systemd[1]: Starting Armbian memory supported logging...
805 [ 9.093290] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
806 [ 12.698524] systemd[1]: Started Armbian memory supported logging.
807 [ 12.714247] systemd[1]: Starting Journal Service...
808 [ 13.176468] systemd[1]: Started Journal Service.
809 [ 13.257243] systemd-journald[570]: Received request to flush runtime journal from PID 1
810
811 ### armbian-release:
812
813 # PLEASE DO NOT EDIT THIS FILE
814 BOARD=rk322x-box
815 BOARD_NAME="rk322x-box"
816 BOARDFAMILY=rk322x
817 BUILD_REPOSITORY_URL=git@github.com:armbian/build.git
818 BUILD_REPOSITORY_COMMIT=08297378c-dirty
819 DISTRIBUTION_CODENAME=buster
820 DISTRIBUTION_STATUS=supported
821 VERSION=21.05.1
822 LINUXFAMILY=rk322x
823 ARCH=arm
824 IMAGE_TYPE=stable
825 BOARD_TYPE=tvb
826 INITRD_ARCH=arm
827 KERNEL_IMAGE_TYPE=Image
828
829 ### boot environment:
830
831 verbosity=1
832 extraargs=coherent_pool=2M
833 bootlogo=false
834 overlay_prefix=rk322x
835 fdtfile=rk322x-box.dtb
836 rootdev=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
837 rootfstype=ext4
838
839 ### lsusb:
840
841 Fri 07 May 2021 08:24:09 PM UTC | rk322x-box | 21.05.1 | armhf | armv7l | 4.4.194-rk322x
842 Bus 007 Device 002: ID 04f3:0103 Elan Microelectronics Corp. ActiveJet K-2024 Multimedia Keyboard
843 Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
844 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
845 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
846 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
847 Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
848 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
849 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
850
851 ### lscpu:
852
853 Architecture: armv7l
854 Byte Order: Little Endian
855 CPU(s): 4
856 On-line CPU(s) list: 0-3
857 Thread(s) per core: 1
858 Core(s) per socket: 4
859 Socket(s): 1
860 Vendor ID: ARM
861 Model: 5
862 Model name: Cortex-A7
863 Stepping: r0p5
864 CPU max MHz: 1200.0000
865 CPU min MHz: 408.0000
866 BogoMIPS: 70.58
867 Flags: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
868
869 ### cpuinfo:
870
871 processor : 0
872 model name : ARMv7 Processor rev 5 (v7l)
873 BogoMIPS : 70.58
874 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
875 CPU implementer : 0x41
876 CPU architecture: 7
877 CPU variant : 0x0
878 CPU part : 0xc07
879 CPU revision : 5
880
881 processor : 1
882 model name : ARMv7 Processor rev 5 (v7l)
883 BogoMIPS : 70.58
884 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
885 CPU implementer : 0x41
886 CPU architecture: 7
887 CPU variant : 0x0
888 CPU part : 0xc07
889 CPU revision : 5
890
891 processor : 2
892 model name : ARMv7 Processor rev 5 (v7l)
893 BogoMIPS : 70.58
894 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
895 CPU implementer : 0x41
896 CPU architecture: 7
897 CPU variant : 0x0
898 CPU part : 0xc07
899 CPU revision : 5
900
901 processor : 3
902 model name : ARMv7 Processor rev 5 (v7l)
903 BogoMIPS : 70.58
904 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
905 CPU implementer : 0x41
906 CPU architecture: 7
907 CPU variant : 0x0
908 CPU part : 0xc07
909 CPU revision : 5
910
911 Hardware : Generic DT based system
912 Revision : 0000
913 Serial : cd1d5ffa03aecfa2
914
915 ### meminfo:
916
917 MemTotal: 985420 kB
918 MemFree: 897072 kB
919 MemAvailable: 923752 kB
920 Buffers: 8768 kB
921 Cached: 34840 kB
922 SwapCached: 0 kB
923 Active: 28284 kB
924 Inactive: 21916 kB
925 Active(anon): 6748 kB
926 Inactive(anon): 10764 kB
927 Active(file): 21536 kB
928 Inactive(file): 11152 kB
929 Unevictable: 0 kB
930 Mlocked: 0 kB
931 HighTotal: 0 kB
932 HighFree: 0 kB
933 LowTotal: 985420 kB
934 LowFree: 897072 kB
935 SwapTotal: 492708 kB
936 SwapFree: 492708 kB
937 Dirty: 816 kB
938 Writeback: 0 kB
939 AnonPages: 6704 kB
940 Mapped: 8312 kB
941 Shmem: 10908 kB
942 Slab: 18744 kB
943 SReclaimable: 10068 kB
944 SUnreclaim: 8676 kB
945 KernelStack: 1016 kB
946 PageTables: 312 kB
947 NFS_Unstable: 0 kB
948 Bounce: 0 kB
949 WritebackTmp: 0 kB
950 CommitLimit: 985416 kB
951 Committed_AS: 28668 kB
952 VmallocTotal: 245760 kB
953 VmallocUsed: 0 kB
954 VmallocChunk: 0 kB
955 CmaTotal: 16384 kB
956 CmaFree: 12200 kB
957
958 ### virtual memory:
959
960 vm.admin_reserve_kbytes = 8192
961 vm.block_dump = 0
962 vm.dirty_background_bytes = 0
963 vm.dirty_background_ratio = 10
964 vm.dirty_bytes = 0
965 vm.dirty_expire_centisecs = 3000
966 vm.dirty_ratio = 20
967 vm.dirtytime_expire_seconds = 43200
968 vm.dirty_writeback_centisecs = 500
969 vm.drop_caches = 0
970 vm.extra_free_kbytes = 0
971 vm.highmem_is_dirtyable = 0
972
973 ### [resize2fs] Leaving 1% spare area. Start resizing partition /dev/mmcblk0p1 now:
974
975 vm.laptop_mode = 0
976 major minor #blocks name
977
978 1 0 4096 ram0
979 179 0 60620800 mmcblk0
980 179 1 1290240 mmcblk0p1
981 253 0 492712 zram0
982 253 1 51200 zram1
983 253 2 492712 zram2
984
985 Executing fdisk, fsck and partprobe:
986 vm.legacy_va_layout = 0
987 vm.lowmem_reserve_ratio = 32 32
988
989 Welcome to fdisk (util-linux 2.33.1).
990 Changes will remain in memory only, until you decide to write them.
991 Be careful before using the write command.
992
993
994 Command (m for help): Selected partition 1
995 Partition 1 has been deleted.
996
997 Command (m for help): Partition type
998 p primary (0 primary, 0 extended, 4 free)
999 e extended (container for logical partitions)
1000 Select (default p): Partition number (1-4, default 1): First sector (2048-121241599, default 2048): Last sector, +/-sectors or +/-size{K,M,G,T,P} (8192-121241599, default 121241599): vm.max_map_count = 65530
1001
1002 Created a new partition 1 of type 'Linux' and of size 57.2 GiB.
1003 Partition #1 contains a ext4 signature.
1004
1005 Command (m for help): vm.min_free_kbytes = 3924
1006 vm.mmap_min_addr = 32768
1007 vm.mmap_rnd_bits = 8
1008 vm.nr_pdflush_threads = 0
1009 vm.oom_dump_tasks = 1
1010
1011 The partition table has been altered.
1012 Syncing disks.
1013
1014 vm.oom_kill_allocating_task = 0
1015 vm.overcommit_kbytes = 0
1016 vm.overcommit_memory = 0
1017 vm.overcommit_ratio = 50
1018 vm.page-cluster = 0
1019 vm.panic_on_oom = 0
1020 vm.percpu_pagelist_fraction = 0
1021 New partition table:
1022
1023 major minor #blocks name
1024
1025 1 0 4096 ram0
1026 179 0 60620800 mmcblk0
1027 179 1 60010496 mmcblk0p1
1028 253 0 492712 zram0
1029 253 1 51200 zram1
1030 253 2 492712 zram2
1031
1032 Now trying to resize ext4 filesystem on /dev/mmcblk0p1 to the limits:
1033
1034 vm.stat_interval = 1
1035 resize2fs 1.44.5 (15-Dec-2018)
1036 vm.swappiness = 100
1037 vm.user_reserve_kbytes = 30422
1038 vm.vfs_cache_pressure = 100
1039
1040 ### ip addr:
1041
1042 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
1043 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
1044 inet XXX.XXX.0.1/8 scope host lo
1045 valid_lft forever preferred_lft forever
1046 inet6 ::1/128 scope host
1047 valid_lft forever preferred_lft forever
1048 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
1049 link/ether 62:4f:b2:6d:a6:71 brd ff:ff:ff:ff:ff:ff
1050 3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
1051 link/ether f6:b4:e0:5a:1e:3a brd ff:ff:ff:ff:ff:ff
1052 4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1
1053 link/sit XXX.XXX.0.0 brd XXX.XXX.0.0
1054
1055 ### partitions:
1056
1057 major minor #blocks name
1058
1059 179 0 60620800 mmcblk0
1060 179 1 60010496 mmcblk0p1
1061 253 0 492712 zram0
1062 253 1 51200 zram1
1063 253 2 492712 zram2
1064
1065 ### df:
1066
1067 udev 471M 0 471M 0% /dev
1068 tmpfs 97M 2.8M 94M 3% /run
1069 /dev/mmcblk0p1 2.0G 1.1G 882M 54% /
1070 tmpfs 482M 0 482M 0% /dev/shm
1071 tmpfs 5.0M 4.0K 5.0M 1% /run/lock
1072 tmpfs 482M 0 482M 0% /sys/fs/cgroup
1073 /dev/zram2 467M 756K 432M 1% /tmp
1074 /dev/zram1 49M 640K 45M 2% /var/log
1075
1076 ### lsblk:
1077
1078 NAME FSTYPE SIZE MOUNTPOINT UUID
1079 mmcblk0 57.8G
1080 └─mmcblk0p1 ext4 57.2G / 2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
1081 zram1 50M /var/log
1082 zram2 481.2M /tmp
1083
1084 ### zramctl:
1085
1086 NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT
1087 /dev/zram2 lzo 481.2M 444K 6.2K 96K 4 /tmp
1088 /dev/zram1 lz4 50M 724K 148.6K 428K 4 /var/log
1089 /dev/zram0 lzo 481.2M 4K 76B 4K 4 [SWAP]
1090
1091 ### mtab:
1092
1093 /dev/mmcblk0p1 / ext4 rw,noatime,errors=remount-ro,commit=600 0 0
1094 /dev/mmcblk0p1 /var/log.hdd ext4 rw,noatime,errors=remount-ro,commit=600 0 0
1095 /dev/zram1 /var/log ext4 rw,relatime,discard 0 0
1096 /dev/zram2 /tmp ext4 rw,nosuid,relatime,discard 0 0
1097
1098 ### mmc0:59b4 info:
1099
1100 cid: 1d41445344202020100000002c015287
1101 csd: 400e00325b590001ce7f7f800a4000cf
1102 scr: 0245804300000000
1103 date: 02/2021
1104 name: SD
1105 type: SD
1106 preferred_erase_size: 4194304
1107 fwrev: 0x0
1108 hwrev: 0x1
1109 oemid: 0x4144
1110 manfid: 0x00001d
1111 serial: 0x0000002c
1112 uevent: DRIVER=mmcblk MMC_TYPE=SD MMC_NAME=SD MODALIAS=mmc:block
1113 erase_size: 512
1114
1115 ### Boot system health:
1116
1117 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St.
1118 20:24:12: 1200MHz 0.69 50% 28% 17% 0% 2% 1% 54.0°C 0/4
1119 20:24:12: 1200MHz 0.69 78% 35% 12% 2% 19% 9% 54.0°C 0/4
1120 20:24:12: 1200MHz 0.69 68% 34% 12% 1% 9% 10% 53.0°C 0/4
1121 20:24:13: 1200MHz 0.69 76% 33% 13% 1% 17% 10% 53.0°C 0/4
1122 20:24:13: 1200MHz 0.69 75% 36% 11% 1% 16% 9% 54.0°C 0/4
1123 Filesystem at /dev/mmcblk0p1 is mounted on /; on-line resizing required
1124 old_desc_blocks = 1, new_desc_blocks = 4
1125 The filesystem on /dev/mmcblk0p1 is now 15002624 (4k) blocks long.
1126
1127
1128 ### [resize2fs] Start resizing ext4 partition /dev/mmcblk0p1 now
1129
1130 resize2fs 1.44.5 (15-Dec-2018)
1131 The filesystem is already 15002624 (4k) blocks long. Nothing to do!
1132
1133
1134 ### quick iozone test: 4 690 823 4215 4523 4502 1097
1135
1136 ### [firstrun] Recreated SSH keys (entropy: 1943 1894)
1137
1138 ### Activated 1 lzo zram swap devices with 481 MB each
1139
1140 ### Activated Armbian ramlog partition with lz4 compression
1141
1142 Fri 07 May 2021 08:33:23 PM UTC | rk322x-box | 21.05.1 | armhf | armv7l | 4.4.194-rk322x
1143
1144 ### dmesg:
1145
1146 [ 0.000000] Booting Linux on physical CPU 0xf00
1147 [ 0.000000] Initializing cgroup subsys cpuset
1148 [ 0.000000] Initializing cgroup subsys cpu
1149 [ 0.000000] Initializing cgroup subsys cpuacct
1150 [ 0.000000] Linux version 4.4.194-rk322x (root@hirsute) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) ) #3 SMP Thu May 6 22:00:38 UTC 2021
1151 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
1152 [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
1153 [ 0.000000] Machine model: Generic RK322x TV Box board
1154 [ 0.000000] cma: Reserved 16 MiB at 0x9f000000
1155 [ 0.000000] Memory policy: Data cache writealloc
1156 [ 0.000000] On node 0 totalpages: 253952
1157 [ 0.000000] free_area_init_node: node 0, pgdat b1253b40, node_mem_map ee6f1000
1158 [ 0.000000] Normal zone: 2304 pages used for memmap
1159 [ 0.000000] Normal zone: 0 pages reserved
1160 [ 0.000000] Normal zone: 253952 pages, LIFO batch:31
1161 [ 0.000000] psci: probing for conduit method from DT.
1162 [ 0.000000] psci: PSCIv1.0 detected in firmware.
1163 [ 0.000000] psci: Using standard PSCI v0.2 function IDs
1164 [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
1165 [ 0.000000] PERCPU: Embedded 14 pages/cpu @ee68f000 s24856 r8192 d24296 u57344
1166 [ 0.000000] pcpu-alloc: s24856 r8192 d24296 u57344 alloc=14*4096
1167 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
1168 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251648
1169 [ 0.000000] Kernel command line: earlyprintk root=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db console=ttyS2,115200n8 console=tty1 rootwait rootfstype=ext4 consoleblank=0 loglevel=1 ubootpart=73c5b759-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u coherent_pool=2M cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
1170 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
1171 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
1172 [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
1173 [ 0.000000] Memory: 962664K/1015808K available (12862K kernel code, 919K rwdata, 3240K rodata, 808K init, 1219K bss, 36760K reserved, 16384K cma-reserved, 0K highmem)
1174 [ 0.000000] Virtual kernel memory layout:
1175 vector : 0xffff0000 - 0xffff1000 ( 4 kB)
1176 fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
1177 vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
1178 lowmem : 0xb0000000 - 0xf0000000 (1024 MB)
1179 pkmap : 0xafe00000 - 0xb0000000 ( 2 MB)
1180 modules : 0xaf000000 - 0xafe00000 ( 14 MB)
1181 .text : 0xb0008000 - 0xb0c97c6c (12864 kB)
1182 .init : 0xb10b0000 - 0xb117a000 ( 808 kB)
1183 .data : 0xb117a000 - 0xb125fe94 ( 920 kB)
1184 .bss : 0xb1261000 - 0xb1391f14 (1220 kB)
1185 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
1186 [ 0.000000] Hierarchical RCU implementation.
1187 [ 0.000000] Build-time adjustment of leaf fanout to 32.
1188 [ 0.000000] NR_IRQS:16 nr_irqs:16 16
1189 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
1190 [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
1191 [ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
1192 [ 0.000023] Switching to timer-based delay loop, resolution 41ns
1193 [ 0.001779] Console: colour dummy device 80x30
1194 [ 0.001963] console [tty1] enabled
1195 [ 0.001989] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
1196 [ 0.002007] pid_max: default: 32768 minimum: 301
1197 [ 0.002137] Security Framework initialized
1198 [ 0.002151] Yama: becoming mindful.
1199 [ 0.002226] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
1200 [ 0.002242] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
1201 [ 0.003125] Initializing cgroup subsys io
1202 [ 0.003159] Initializing cgroup subsys memory
1203 [ 0.003202] Initializing cgroup subsys devices
1204 [ 0.003222] Initializing cgroup subsys freezer
1205 [ 0.003239] Initializing cgroup subsys net_cls
1206 [ 0.003256] Initializing cgroup subsys perf_event
1207 [ 0.003273] Initializing cgroup subsys net_prio
1208 [ 0.003303] Initializing cgroup subsys pids
1209 [ 0.003371] CPU: Testing write buffer coherency: ok
1210 [ 0.003420] ftrace: allocating 41892 entries in 123 pages
1211 [ 0.082730] /cpus/cpu@f00 missing clock-frequency property
1212 [ 0.082762] /cpus/cpu@f01 missing clock-frequency property
1213 [ 0.082781] /cpus/cpu@f02 missing clock-frequency property
1214 [ 0.082800] /cpus/cpu@f03 missing clock-frequency property
1215 [ 0.082813] CPU0: update cpu_capacity 430
1216 [ 0.082825] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
1217 [ 0.082909] Setting up static identity map for 0x60008280 - 0x600082d8
1218 [ 0.094124] CPU1: update cpu_capacity 430
1219 [ 0.094133] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
1220 [ 0.103630] CPU2: update cpu_capacity 430
1221 [ 0.103638] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
1222 [ 0.113070] CPU3: update cpu_capacity 430
1223 [ 0.113078] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
1224 [ 0.113211] Brought up 4 CPUs
1225 [ 0.113251] SMP: Total of 4 processors activated (192.00 BogoMIPS).
1226 [ 0.113259] CPU: All CPU(s) started in SVC mode.
1227 [ 0.114773] devtmpfs: initialized
1228 [ 0.134250] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
1229 [ 0.134837] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
1230 [ 0.134876] futex hash table entries: 1024 (order: 4, 65536 bytes)
1231 [ 0.136210] xor: measuring software checksum speed
1232 [ 0.174761] arm4regs : 1011.000 MB/sec
1233 [ 0.214864] 8regs : 705.000 MB/sec
1234 [ 0.254967] 32regs : 684.000 MB/sec
1235 [ 0.295067] neon : 1018.000 MB/sec
1236 [ 0.295077] xor: using function: neon (1018.000 MB/sec)
1237 [ 0.295119] pinctrl core: initialized pinctrl subsystem
1238 [ 0.296661] NET: Registered protocol family 16
1239 [ 0.299189] DMA: preallocated 2048 KiB pool for atomic coherent allocations
1240 [ 0.311220] cpuidle: using governor ladder
1241 [ 0.323236] cpuidle: using governor menu
1242 [ 0.339952] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0
1243 [ 0.340115] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1
1244 [ 0.340270] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2
1245 [ 0.340429] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3
1246 [ 0.346645] console [pstore-1] enabled
1247 [ 0.346657] pstore: Registered ramoops as persistent store backend
1248 [ 0.346669] ramoops: attached 0xf0000@0x62e00000, ecc: 0/0
1249 [ 0.349994] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
1250 [ 0.350014] hw-breakpoint: maximum watchpoint size is 8 bytes.
1251 [ 0.350233] sip_firmware_init: set rockchip sip version v2 failed
1252 [ 0.448081] raid6: int32x1 gen() 133 MB/s
1253 [ 0.516228] raid6: int32x1 xor() 131 MB/s
1254 [ 0.584427] raid6: int32x2 gen() 166 MB/s
1255 [ 0.652490] raid6: int32x2 xor() 136 MB/s
1256 [ 0.720835] raid6: int32x4 gen() 163 MB/s
1257 [ 0.788980] raid6: int32x4 xor() 137 MB/s
1258 [ 0.857229] raid6: int32x8 gen() 166 MB/s
1259 [ 0.925492] raid6: int32x8 xor() 113 MB/s
1260 [ 0.993629] raid6: neonx1 gen() 382 MB/s
1261 [ 1.061769] raid6: neonx1 xor() 290 MB/s
1262 [ 1.129953] raid6: neonx2 gen() 519 MB/s
1263 [ 1.198081] raid6: neonx2 xor() 376 MB/s
1264 [ 1.266291] raid6: neonx4 gen() 581 MB/s
1265 [ 1.334496] raid6: neonx4 xor() 400 MB/s
1266 [ 1.402796] raid6: neonx8 gen() 560 MB/s
1267 [ 1.470953] raid6: neonx8 xor() 391 MB/s
1268 [ 1.470965] raid6: using algorithm neonx4 gen() 581 MB/s
1269 [ 1.470975] raid6: .... xor() 400 MB/s, rmw enabled
1270 [ 1.470985] raid6: using intx1 recovery algorithm
1271 [ 1.471975] rockchip-pm rockchip-suspend: not set wakeup-config
1272 [ 1.471997] rockchip-pm rockchip-suspend: not set pwm-regulator-config
1273 [ 1.472371] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@0[0]'
1274 [ 1.472858] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@1[0]'
1275 [ 1.473478] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc-host-regulator[0]' - status (0)
1276 [ 1.474078] of_get_named_gpiod_flags: parsed 'gpio' property of node '/otg-vbus-regulator[0]' - status (0)
1277 [ 1.474586] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]'
1278 [ 1.475495] iommu: Adding device 20020000.vpu-service to group 0
1279 [ 1.475604] iommu: Adding device 20030000.rkvdec to group 1
1280 [ 1.475698] iommu: Adding device 20050000.vop to group 2
1281 [ 1.475791] iommu: Adding device 20070000.iep to group 3
1282 [ 1.476316] rk_iommu 20020800.iommu: can't get sclk
1283 [ 1.476908] rk_iommu 20030480.iommu: can't get sclk
1284 [ 1.477149] rk_iommu 20053f00.iommu: can't get sclk
1285 [ 1.477296] rk_iommu 20070800.iommu: can't get aclk
1286 [ 1.477315] rk_iommu 20070800.iommu: can't get hclk
1287 [ 1.477331] rk_iommu 20070800.iommu: can't get sclk
1288 [ 1.478081] SCSI subsystem initialized
1289 [ 1.478495] usbcore: registered new interface driver usbfs
1290 [ 1.478593] usbcore: registered new interface driver hub
1291 [ 1.478708] usbcore: registered new device driver usb
1292 [ 1.478934] media: Linux media interface: v0.10
1293 [ 1.479097] Linux video capture interface: v2.00
1294 [ 1.479350] pps_core: LinuxPPS API ver. 1 registered
1295 [ 1.479365] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
1296 [ 1.479409] PTP clock support registered
1297 [ 1.481330] Advanced Linux Sound Architecture Driver Initialized.
1298 [ 1.482326] Bluetooth: Core ver 2.21
1299 [ 1.482394] NET: Registered protocol family 31
1300 [ 1.482407] Bluetooth: HCI device and connection manager initialized
1301 [ 1.482428] Bluetooth: HCI socket layer initialized
1302 [ 1.482445] Bluetooth: L2CAP socket layer initialized
1303 [ 1.482499] Bluetooth: SCO socket layer initialized
1304 [ 1.483348] NetLabel: Initializing
1305 [ 1.483369] NetLabel: domain hash size = 128
1306 [ 1.483378] NetLabel: protocols = UNLABELED CIPSOv4
1307 [ 1.483452] NetLabel: unlabeled traffic allowed by default
1308 [ 1.484791] clocksource: Switched to clocksource arch_sys_counter
1309 [ 1.579727] NET: Registered protocol family 2
1310 [ 1.580572] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
1311 [ 1.580687] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
1312 [ 1.581121] TCP: Hash tables configured (established 8192 bind 8192)
1313 [ 1.581227] UDP hash table entries: 512 (order: 2, 24576 bytes)
1314 [ 1.581296] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
1315 [ 1.581643] NET: Registered protocol family 1
1316 [ 1.582312] RPC: Registered named UNIX socket transport module.
1317 [ 1.582336] RPC: Registered udp transport module.
1318 [ 1.582347] RPC: Registered tcp transport module.
1319 [ 1.582357] RPC: Registered tcp NFSv4.1 backchannel transport module.
1320 [ 1.582675] Trying to unpack rootfs image as initramfs...
1321 [ 1.955432] Freeing initrd memory: 5564K
1322 [ 1.956457] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
1323 [ 1.959405] Initialise system trusted keyring
1324 [ 1.973283] VFS: Disk quotas dquot_6.6.0
1325 [ 1.973596] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
1326 [ 1.976249] squashfs: version 4.0 (2009/01/31) Phillip Lougher
1327 [ 1.979676] NFS: Registering the id_resolver key type
1328 [ 1.979740] Key type id_resolver registered
1329 [ 1.979752] Key type id_legacy registered
1330 [ 1.979788] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
1331 [ 1.979901] ntfs: driver 2.1.32 [Flags: R/W].
1332 [ 1.980944] JFS: nTxBlock = 7692, nTxLock = 61538
1333 [ 1.989607] SGI XFS with security attributes, no debug enabled
1334 [ 1.998768] NET: Registered protocol family 38
1335 [ 1.998821] Key type asymmetric registered
1336 [ 1.998842] Asymmetric key parser 'x509' registered
1337 [ 1.999241] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
1338 [ 1.999655] io scheduler noop registered
1339 [ 1.999686] io scheduler deadline registered
1340 [ 1.999768] io scheduler cfq registered (default)
1341 [ 2.002955] phy phy-11000000.syscon:usb2-phy@800.2: Failed to get VBUS supply regulator
1342 [ 2.008001] rk-vcodec 20020000.vpu-service: no regulator for vcodec
1343 [ 2.008404] rk-vcodec 20020000.vpu-service: probe device
1344 [ 2.008871] rk-vcodec 20020000.vpu-service: drm allocator with mmu enabled
1345 [ 2.010094] rk-vcodec 20020000.vpu-service: could not find power_model node
1346 [ 2.010121] rk-vcodec 20020000.vpu-service: init success
1347 [ 2.010441] rk-vcodec 20030000.rkvdec: vcodec regulator not ready, retry
1348 [ 2.014706] dma-pl330 110f0000.pdma: Loaded driver for PL330 DMAC-241330
1349 [ 2.014733] dma-pl330 110f0000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
1350 [ 2.015854] rockchip-system-monitor rockchip-system-monitor: system monitor probe
1351 [ 2.016335] pwm-regulator vdd-arm-regulator: GPIO lookup for consumer enable
1352 [ 2.016355] pwm-regulator vdd-arm-regulator: using device tree for GPIO lookup
1353 [ 2.016372] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-arm-regulator[0]'
1354 [ 2.016387] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-arm-regulator[0]'
1355 [ 2.016400] pwm-regulator vdd-arm-regulator: using lookup tables for GPIO lookup
1356 [ 2.016415] pwm-regulator vdd-arm-regulator: lookup for GPIO enable failed
1357 [ 2.017132] pwm-regulator vdd-log-regulator: GPIO lookup for consumer enable
1358 [ 2.017157] pwm-regulator vdd-log-regulator: using device tree for GPIO lookup
1359 [ 2.017173] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log-regulator[0]'
1360 [ 2.017188] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log-regulator[0]'
1361 [ 2.017201] pwm-regulator vdd-log-regulator: using lookup tables for GPIO lookup
1362 [ 2.017216] pwm-regulator vdd-log-regulator: lookup for GPIO enable failed
1363 [ 2.018254] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
1364 [ 2.019047] 11030000.serial: ttyS2 at MMIO 0x11030000 (irq = 30, base_baud = 1500000) is a 16550A
1365 [ 2.019870] console [ttyS2] enabled
1366 [ 2.021716] [drm] Initialized drm 1.1.0 20060810
1367 [ 2.024197] [drm] Rockchip DRM driver version: v1.0.1
1368 [ 2.024432] rockchip-drm display-subsystem: devfreq is not set
1369 [ 2.025238] rockchip-drm display-subsystem: bound 20050000.vop (ops 0xb0d1b2b0)
1370 [ 2.025627] i2c i2c-0: of_i2c: modalias failure on /hdmi@200a0000/ports
1371 [ 2.025654] dwhdmi-rockchip 200a0000.hdmi: registered DesignWare HDMI I2C bus driver
1372 [ 2.025764] dwhdmi-rockchip 200a0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (inno_dw_hdmi_phy)
1373 [ 2.027025] rockchip-drm display-subsystem: bound 200a0000.hdmi (ops 0xb0d13808)
1374 [ 2.027050] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
1375 [ 2.027060] [drm] No driver support for vblank timestamp query.
1376 [ 2.027175] rockchip-drm display-subsystem: failed to parse display resources
1377 [ 2.027238] rockchip-drm display-subsystem: No connectors reported connected with modes
1378 [ 2.027325] [drm] Cannot find any crtc or sizes - going 1024x768
1379 [ 2.049646] Console: switching to colour frame buffer device 128x48
1380 [ 2.065034] rockchip-drm display-subsystem: fb0: frame buffer device
1381 [ 2.081353] Registered IR keymap rc-cec
1382 [ 2.081622] rc rc0: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0
1383 [ 2.082282] input: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0/input0
1384 [ 2.084408] brd: module loaded
1385 [ 2.095567] loop: module loaded
1386 [ 2.095658] lkdtm: No crash points registered, enable through debugfs
1387 [ 2.098209] libphy: Fixed MDIO Bus: probed
1388 [ 2.098241] tun: Universal TUN/TAP device driver, 1.6
1389 [ 2.098253] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
1390 [ 2.098601] CAN device driver interface
1391 [ 2.099992] rk_gmac-dwmac 30200000.ethernet: clock input or output? (output).
1392 [ 2.100020] rk_gmac-dwmac 30200000.ethernet: TX delay(0x30).
1393 [ 2.100035] rk_gmac-dwmac 30200000.ethernet: RX delay(0x10).
1394 [ 2.100077] rk_gmac-dwmac 30200000.ethernet: integrated PHY? (yes).
1395 [ 2.100248] rk_gmac-dwmac 30200000.ethernet: cannot get clock clk_mac_speed
1396 [ 2.105327] rk_gmac-dwmac 30200000.ethernet: init for RMII
1397 [ 2.140929] stmmac - user ID: 0x10, Synopsys ID: 0x35
1398 [ 2.140945] Ring mode enabled
1399 [ 2.140956] DMA HW capability register supported
1400 [ 2.140965] Normal descriptors
1401 [ 2.140977] RX Checksum Offload Engine supported (type 2)
1402 [ 2.140986] TX Checksum insertion supported
1403 [ 2.140994] Wake-Up On Lan supported
1404 [ 2.141087] rk_gmac-dwmac 30200000.ethernet: rk_get_eth_addr: mac address: f6:b4:e0:5a:1e:3a
1405 [ 2.141101] eth%d: device MAC address f6:b4:e0:5a:1e:3a
1406 [ 2.141110] Enable RX Mitigation via HW Watchdog Timer
1407 [ 2.141312] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@30200000[0]' - status (0)
1408 [ 2.546537] libphy: stmmac: probed
1409 [ 2.546567] eth%d: PHY ID 1234d400 at 0 IRQ POLL (stmmac-0:00) active
1410 [ 2.546580] eth%d: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
1411 [ 2.546593] eth%d: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
1412 [ 2.546606] eth%d: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
1413 [ 2.546619] eth%d: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
1414 [ 2.546631] eth%d: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
1415 [ 2.546643] eth%d: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
1416 [ 2.546656] eth%d: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
1417 [ 2.546668] eth%d: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
1418 [ 2.546681] eth%d: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
1419 [ 2.546693] eth%d: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
1420 [ 2.546706] eth%d: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
1421 [ 2.546718] eth%d: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
1422 [ 2.546731] eth%d: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
1423 [ 2.546743] eth%d: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
1424 [ 2.546756] eth%d: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
1425 [ 2.546768] eth%d: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
1426 [ 2.546780] eth%d: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
1427 [ 2.546793] eth%d: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
1428 [ 2.546805] eth%d: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
1429 [ 2.546818] eth%d: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
1430 [ 2.546830] eth%d: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
1431 [ 2.546842] eth%d: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
1432 [ 2.546855] eth%d: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
1433 [ 2.546867] eth%d: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
1434 [ 2.546879] eth%d: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
1435 [ 2.546892] eth%d: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
1436 [ 2.546904] eth%d: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
1437 [ 2.546916] eth%d: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
1438 [ 2.546929] eth%d: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
1439 [ 2.546941] eth%d: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
1440 [ 2.546953] eth%d: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
1441 [ 2.548402] PPP generic driver version 2.4.2
1442 [ 2.548852] Atmel at76x USB Wireless LAN Driver 0.17 loading
1443 [ 2.548999] usbcore: registered new interface driver at76c50x-usb
1444 [ 2.549132] usbcore: registered new interface driver rtl8187
1445 [ 2.549250] usbcore: registered new interface driver rndis_wlan
1446 [ 2.549372] usbcore: registered new interface driver zd1201
1447 [ 2.549774] usbcore: registered new interface driver rt2800usb
1448 [ 2.549890] Rockchip WiFi SYS interface (V1.00) ...
1449 [ 2.549957] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
1450 [ 2.550043] usbcore: registered new interface driver pegasus
1451 [ 2.550130] usbcore: registered new interface driver rtl8150
1452 [ 2.550213] usbcore: registered new interface driver r8152
1453 [ 2.550326] usbcore: registered new interface driver asix
1454 [ 2.550411] usbcore: registered new interface driver ax88179_178a
1455 [ 2.550492] usbcore: registered new interface driver cdc_ether
1456 [ 2.550573] usbcore: registered new interface driver dm9601
1457 [ 2.550676] usbcore: registered new interface driver smsc75xx
1458 [ 2.550781] usbcore: registered new interface driver smsc95xx
1459 [ 2.550863] usbcore: registered new interface driver net1080
1460 [ 2.550946] usbcore: registered new interface driver rndis_host
1461 [ 2.551056] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
1462 [ 2.551198] usbcore: registered new interface driver cdc_ncm
1463 [ 2.551285] usbcore: registered new interface driver cdc_mbim
1464 [ 2.551779] 30040000.usb supply vusb_d not found, using dummy regulator
1465 [ 2.551878] 30040000.usb supply vusb_a not found, using dummy regulator
1466 [ 2.565079] dwc2 30040000.usb: DWC OTG Controller
1467 [ 2.565131] dwc2 30040000.usb: new USB bus registered, assigned bus number 1
1468 [ 2.565189] dwc2 30040000.usb: irq 49, io mem 0x30040000
1469 [ 2.565526] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
1470 [ 2.565544] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
1471 [ 2.565558] usb usb1: Product: DWC OTG Controller
1472 [ 2.565572] usb usb1: Manufacturer: Linux 4.4.194-rk322x dwc2_hsotg
1473 [ 2.565586] usb usb1: SerialNumber: 30040000.usb
1474 [ 2.566577] hub 1-0:1.0: USB hub found
1475 [ 2.566646] hub 1-0:1.0: 1 port detected
1476 [ 2.568184] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
1477 [ 2.568211] ehci-platform: EHCI generic platform driver
1478 [ 2.570749] ehci-platform 30080000.usb: EHCI Host Controller
1479 [ 2.571136] ehci-platform 30080000.usb: new USB bus registered, assigned bus number 2
1480 [ 2.571421] ehci-platform 30080000.usb: irq 50, io mem 0x30080000
1481 [ 2.580838] ehci-platform 30080000.usb: USB 2.0 started, EHCI 1.00
1482 [ 2.581137] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
1483 [ 2.581156] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
1484 [ 2.581171] usb usb2: Product: EHCI Host Controller
1485 [ 2.581184] usb usb2: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
1486 [ 2.581198] usb usb2: SerialNumber: 30080000.usb
1487 [ 2.582175] hub 2-0:1.0: USB hub found
1488 [ 2.582248] hub 2-0:1.0: 1 port detected
1489 [ 2.585146] ehci-platform 300c0000.usb: EHCI Host Controller
1490 [ 2.585568] ehci-platform 300c0000.usb: new USB bus registered, assigned bus number 3
1491 [ 2.585844] ehci-platform 300c0000.usb: irq 52, io mem 0x300c0000
1492 [ 2.596837] ehci-platform 300c0000.usb: USB 2.0 started, EHCI 1.00
1493 [ 2.597150] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
1494 [ 2.597170] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
1495 [ 2.597184] usb usb3: Product: EHCI Host Controller
1496 [ 2.597198] usb usb3: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
1497 [ 2.597212] usb usb3: SerialNumber: 300c0000.usb
1498 [ 2.598182] hub 3-0:1.0: USB hub found
1499 [ 2.598249] hub 3-0:1.0: 1 port detected
1500 [ 2.601161] ehci-platform 30100000.usb: EHCI Host Controller
1501 [ 2.601536] ehci-platform 30100000.usb: new USB bus registered, assigned bus number 4
1502 [ 2.601832] ehci-platform 30100000.usb: irq 54, io mem 0x30100000
1503 [ 2.612832] ehci-platform 30100000.usb: USB 2.0 started, EHCI 1.00
1504 [ 2.613121] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
1505 [ 2.613140] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
1506 [ 2.613154] usb usb4: Product: EHCI Host Controller
1507 [ 2.613168] usb usb4: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
1508 [ 2.613181] usb usb4: SerialNumber: 30100000.usb
1509 [ 2.614183] hub 4-0:1.0: USB hub found
1510 [ 2.614253] hub 4-0:1.0: 1 port detected
1511 [ 2.615062] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
1512 [ 2.615135] ohci-platform: OHCI generic platform driver
1513 [ 2.615531] ohci-platform 300a0000.usb: Generic Platform OHCI controller
1514 [ 2.615937] ohci-platform 300a0000.usb: new USB bus registered, assigned bus number 5
1515 [ 2.616205] ohci-platform 300a0000.usb: irq 51, io mem 0x300a0000
1516 [ 2.673081] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
1517 [ 2.673104] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
1518 [ 2.673118] usb usb5: Product: Generic Platform OHCI controller
1519 [ 2.673132] usb usb5: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
1520 [ 2.673146] usb usb5: SerialNumber: 300a0000.usb
1521 [ 2.674183] hub 5-0:1.0: USB hub found
1522 [ 2.674256] hub 5-0:1.0: 1 port detected
1523 [ 2.675105] ohci-platform 300e0000.usb: Generic Platform OHCI controller
1524 [ 2.675482] ohci-platform 300e0000.usb: new USB bus registered, assigned bus number 6
1525 [ 2.675730] ohci-platform 300e0000.usb: irq 53, io mem 0x300e0000
1526 [ 2.733079] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
1527 [ 2.733101] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
1528 [ 2.733116] usb usb6: Product: Generic Platform OHCI controller
1529 [ 2.733130] usb usb6: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
1530 [ 2.733143] usb usb6: SerialNumber: 300e0000.usb
1531 [ 2.734120] hub 6-0:1.0: USB hub found
1532 [ 2.734196] hub 6-0:1.0: 1 port detected
1533 [ 2.734977] ohci-platform 30120000.usb: Generic Platform OHCI controller
1534 [ 2.735357] ohci-platform 30120000.usb: new USB bus registered, assigned bus number 7
1535 [ 2.735617] ohci-platform 30120000.usb: irq 55, io mem 0x30120000
1536 [ 2.793111] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
1537 [ 2.793133] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
1538 [ 2.793148] usb usb7: Product: Generic Platform OHCI controller
1539 [ 2.793161] usb usb7: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
1540 [ 2.793175] usb usb7: SerialNumber: 30120000.usb
1541 [ 2.794149] hub 7-0:1.0: USB hub found
1542 [ 2.794217] hub 7-0:1.0: 1 port detected
1543 [ 2.795120] usbcore: registered new interface driver cdc_acm
1544 [ 2.795137] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
1545 [ 2.795245] usbcore: registered new interface driver cdc_wdm
1546 [ 2.795548] usbcore: registered new interface driver usb-storage
1547 [ 2.795723] usbcore: registered new interface driver usbserial
1548 [ 2.795801] usbcore: registered new interface driver usbserial_generic
1549 [ 2.795865] usbserial: USB Serial support registered for generic
1550 [ 2.795977] usbcore: registered new interface driver keyspan
1551 [ 2.796038] usbserial: USB Serial support registered for Keyspan - (without firmware)
1552 [ 2.796095] usbserial: USB Serial support registered for Keyspan 1 port adapter
1553 [ 2.796152] usbserial: USB Serial support registered for Keyspan 2 port adapter
1554 [ 2.796210] usbserial: USB Serial support registered for Keyspan 4 port adapter
1555 [ 2.796322] usbcore: registered new interface driver option
1556 [ 2.796390] usbserial: USB Serial support registered for GSM modem (1-port)
1557 [ 2.797142] usbcore: registered new interface driver oti6858
1558 [ 2.797216] usbserial: USB Serial support registered for oti6858
1559 [ 2.797321] usbcore: registered new interface driver qcserial
1560 [ 2.797384] usbserial: USB Serial support registered for Qualcomm USB modem
1561 [ 2.797544] usbcore: registered new interface driver sierra
1562 [ 2.797605] usbserial: USB Serial support registered for Sierra USB modem
1563 [ 2.799079] usbcore: registered new interface driver iforce
1564 [ 2.799236] usbcore: registered new interface driver xpad
1565 [ 2.799548] usbcore: registered new interface driver usbtouchscreen
1566 [ 2.800730] i2c /dev entries driver
1567 [ 2.802747] IR NEC protocol handler initialized
1568 [ 2.802775] IR RC5(x/sz) protocol handler initialized
1569 [ 2.802793] IR RC6 protocol handler initialized
1570 [ 2.802809] IR JVC protocol handler initialized
1571 [ 2.802827] IR Sony protocol handler initialized
1572 [ 2.802843] IR SANYO protocol handler initialized
1573 [ 2.802860] IR Sharp protocol handler initialized
1574 [ 2.802878] IR MCE Keyboard/mouse protocol handler initialized
1575 [ 2.802895] IR XMP protocol handler initialized
1576 [ 2.804609] usbcore: registered new interface driver uvcvideo
1577 [ 2.804623] USB Video Class driver (1.1.1)
1578 [ 2.806591] Boot mode: normal
1579 [ 2.807776] rockchip-thermal 11150000.tsadc: tsadc is probed successfully!
1580 [ 2.809531] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
1581 [ 2.809885] Bluetooth: Virtual HCI driver ver 1.5
1582 [ 2.810150] Bluetooth: HCI UART driver ver 2.3
1583 [ 2.810168] Bluetooth: HCI UART protocol H4 registered
1584 [ 2.810179] Bluetooth: HCI UART protocol LL registered
1585 [ 2.810190] Bluetooth: HCI UART protocol ATH3K registered
1586 [ 2.810201] Bluetooth: HCI UART protocol Three-wire (H5) registered
1587 [ 2.810366] Bluetooth: HCI UART protocol BCM registered
1588 [ 2.810516] usbcore: registered new interface driver bfusb
1589 [ 2.810660] usbcore: registered new interface driver btusb
1590 [ 2.810683] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
1591 [ 2.811283] cpu cpu0: leakage=6
1592 [ 2.811316] cpu cpu0: leakage-volt-sel=0
1593 [ 2.811522] cpu cpu0: Failed to get pvtm
1594 [ 2.812946] cpu cpu0: avs=0
1595 [ 2.813023] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
1596 [ 2.813047] cpu cpu0: failed to read out thermal zone (-22)
1597 [ 2.813682] cpu cpu0: failed to find power_model node
1598 [ 2.814317] pwrseq_simple sdio-pwrseq: GPIO lookup for consumer reset
1599 [ 2.814335] pwrseq_simple sdio-pwrseq: using device tree for GPIO lookup
1600 [ 2.814357] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0)
1601 [ 2.814698] Synopsys Designware Multimedia Card Interface Driver
1602 [ 2.815311] dwmmc_rockchip 30000000.dwmmc: IDMAC supports 32-bit address mode.
1603 [ 2.815434] dwmmc_rockchip 30000000.dwmmc: Using internal DMA controller.
1604 [ 2.815451] dwmmc_rockchip 30000000.dwmmc: Version ID is 270a
1605 [ 2.815514] dwmmc_rockchip 30000000.dwmmc: DW MMC controller at irq 45,32 bit host data width,256 deep fifo
1606 [ 2.815582] dwmmc_rockchip 30000000.dwmmc: No vmmc regulator found
1607 [ 2.815593] dwmmc_rockchip 30000000.dwmmc: No vqmmc regulator found
1608 [ 2.815615] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer cd
1609 [ 2.815625] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
1610 [ 2.815652] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/dwmmc@30000000[0]' - status (0)
1611 [ 2.815687] gpio-49 (cd): gpiod_set_debounce: missing set() or set_debounce() operations
1612 [ 2.815698] dwmmc_rockchip 30000000.dwmmc: Got CD GPIO
1613 [ 2.815710] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer wp
1614 [ 2.815719] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
1615 [ 2.815729] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30000000[0]'
1616 [ 2.815739] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30000000[0]'
1617 [ 2.815748] dwmmc_rockchip 30000000.dwmmc: using lookup tables for GPIO lookup
1618 [ 2.815758] dwmmc_rockchip 30000000.dwmmc: lookup for GPIO wp failed
1619 [ 2.828573] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
1620 [ 2.841476] dwmmc_rockchip 30000000.dwmmc: 1 slots initialized
1621 [ 2.841827] dwmmc_rockchip 30010000.dwmmc: num-slots property not found, assuming 1 slot is available
1622 [ 2.841913] dwmmc_rockchip 30010000.dwmmc: IDMAC supports 32-bit address mode.
1623 [ 2.842002] dwmmc_rockchip 30010000.dwmmc: Using internal DMA controller.
1624 [ 2.842018] dwmmc_rockchip 30010000.dwmmc: Version ID is 270a
1625 [ 2.842072] dwmmc_rockchip 30010000.dwmmc: DW MMC controller at irq 46,32 bit host data width,256 deep fifo
1626 [ 2.842123] dwmmc_rockchip 30010000.dwmmc: No vmmc regulator found
1627 [ 2.842133] dwmmc_rockchip 30010000.dwmmc: No vqmmc regulator found
1628 [ 2.842151] dwmmc_rockchip 30010000.dwmmc: GPIO lookup for consumer wp
1629 [ 2.842161] dwmmc_rockchip 30010000.dwmmc: using device tree for GPIO lookup
1630 [ 2.842174] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30010000[0]'
1631 [ 2.842184] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30010000[0]'
1632 [ 2.842193] dwmmc_rockchip 30010000.dwmmc: using lookup tables for GPIO lookup
1633 [ 2.842203] dwmmc_rockchip 30010000.dwmmc: lookup for GPIO wp failed
1634 [ 2.842270] dwmmc_rockchip 30010000.dwmmc: allocated mmc-pwrseq
1635 [ 2.855029] mmc_host mmc1: Bus speed (slot 0) = 976562Hz (slot req 400000Hz, actual 244140HZ div = 2)
1636 [ 2.867671] dwmmc_rockchip 30010000.dwmmc: 1 slots initialized
1637 [ 2.868039] dwmmc_rockchip 30020000.dwmmc: IDMAC supports 32-bit address mode.
1638 [ 2.868207] dwmmc_rockchip 30020000.dwmmc: Using internal DMA controller.
1639 [ 2.868226] dwmmc_rockchip 30020000.dwmmc: Version ID is 270a
1640 [ 2.868302] dwmmc_rockchip 30020000.dwmmc: DW MMC controller at irq 47,32 bit host data width,256 deep fifo
1641 [ 2.868353] dwmmc_rockchip 30020000.dwmmc: No vmmc regulator found
1642 [ 2.868364] dwmmc_rockchip 30020000.dwmmc: No vqmmc regulator found
1643 [ 2.868381] dwmmc_rockchip 30020000.dwmmc: GPIO lookup for consumer wp
1644 [ 2.868392] dwmmc_rockchip 30020000.dwmmc: using device tree for GPIO lookup
1645 [ 2.868404] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30020000[0]'
1646 [ 2.868416] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30020000[0]'
1647 [ 2.868425] dwmmc_rockchip 30020000.dwmmc: using lookup tables for GPIO lookup
1648 [ 2.868436] dwmmc_rockchip 30020000.dwmmc: lookup for GPIO wp failed
1649 [ 2.873208] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
1650 [ 2.873297] mmc0: new high speed SDXC card at address 59b4
1651 [ 2.874020] mmcblk0: mmc0:59b4 SD 57.8 GiB
1652 [ 2.875707] mmcblk0: p1
1653 [ 2.880885] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
1654 [ 2.893078] dwmmc_rockchip 30020000.dwmmc: 1 slots initialized
1655 [ 2.893904] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/working[0]' - status (0)
1656 [ 2.894468] ledtrig-cpu: registered to indicate activity on CPUs
1657 [ 2.894753] hidraw: raw HID events driver (C) Jiri Kosina
1658 [ 2.895461] usbcore: registered new interface driver usbhid
1659 [ 2.895482] usbhid: USB HID core driver
1660 [ 2.896081] ashmem: initialized
1661 [ 2.899645] rknandbase v1.2 2018-05-08
1662 [ 2.900075] rknand 30030000.nandc: rknand_probe clk rate = 150000000
1663 [ 2.900425] ftl_init fffffffe
1664 [ 2.900443] rk_ftl_init fail
1665 [ 2.901918] usbcore: registered new interface driver snd-usb-audio
1666 [ 2.902126] usbcore: registered new interface driver snd-ua101
1667 [ 2.902307] usbcore: registered new interface driver snd-usb-caiaq
1668 [ 2.902475] usbcore: registered new interface driver snd-usb-6fire
1669 [ 2.902656] usbcore: registered new interface driver snd-usb-hiface
1670 [ 2.902793] usbcore: registered new interface driver snd-bcd2000
1671 [ 2.902929] usbcore: registered new interface driver snd_usb_pod
1672 [ 2.903066] usbcore: registered new interface driver snd_usb_podhd
1673 [ 2.903214] usbcore: registered new interface driver snd_usb_toneport
1674 [ 2.903352] usbcore: registered new interface driver snd_usb_variax
1675 [ 2.910997] u32 classifier
1676 [ 2.911023] input device check on
1677 [ 2.911037] Actions configured
1678 [ 2.911067] Netfilter messages via NETLINK v0.30.
1679 [ 2.911111] nfnl_acct: registering with nfnetlink.
1680 [ 2.911255] nf_conntrack version 0.5.0 (15384 buckets, 61536 max)
1681 [ 2.912033] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
1682 [ 2.912597] Initializing XFRM netlink socket
1683 [ 2.914348] NET: Registered protocol family 10
1684 [ 2.914643] mmc1: new high speed SDIO card at address 0001
1685 [ 2.916264] ip6_tables: (C) 2000-2006 Netfilter Core Team
1686 [ 2.916934] sit: IPv6 over IPv4 tunneling driver
1687 [ 2.918266] NET: Registered protocol family 17
1688 [ 2.918333] NET: Registered protocol family 15
1689 [ 2.918431] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
1690 [ 2.918508] Bridge firewalling registered
1691 [ 2.918533] can: controller area network core (rev 20120528 abi 9)
1692 [ 2.918651] NET: Registered protocol family 29
1693 [ 2.918682] can: raw protocol (rev 20120528)
1694 [ 2.918708] can: broadcast manager protocol (rev 20120528 t)
1695 [ 2.918741] can: netlink gateway (rev 20130117) max_hops=1
1696 [ 2.919389] Bluetooth: RFCOMM TTY layer initialized
1697 [ 2.919436] Bluetooth: RFCOMM socket layer initialized
1698 [ 2.919486] Bluetooth: RFCOMM ver 1.11
1699 [ 2.919529] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
1700 [ 2.919557] Bluetooth: HIDP socket layer initialized
1701 [ 2.919674] 8021q: 802.1Q VLAN Support v1.8
1702 [ 2.919746] lib80211: common routines for IEEE802.11 drivers
1703 [ 2.919766] lib80211_crypt: registered algorithm 'NULL'
1704 [ 2.919795] lib80211_crypt: registered algorithm 'WEP'
1705 [ 2.919822] lib80211_crypt: registered algorithm 'CCMP'
1706 [ 2.919850] lib80211_crypt: registered algorithm 'TKIP'
1707 [ 2.919873] [WLAN_RFKILL]: Enter rfkill_wlan_init
1708 [ 2.920277] [BT_RFKILL]: Enter rfkill_rk_init
1709 [ 2.920623] Key type dns_resolver registered
1710 [ 2.921186] flash vendor_init_thread!
1711 [ 2.921213] flash vendor storage:20170308 ret = -1
1712 [ 2.921304] Error: Driver 'sc031gs' is already registered, aborting...
1713 [ 2.922511] Registering SWP/SWPB emulation handler
1714 [ 2.924174] registered taskstats version 1
1715 [ 2.924218] Loading compiled-in X.509 certificates
1716 [ 2.924965] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
1717 [ 2.927498] Btrfs loaded
1718 [ 2.928447] rga2: Driver loaded successfully ver:4.01
1719 [ 2.928675] rga2: Module initialized.
1720 [ 2.928712] pvtm list NULL
1721 [ 2.929795] rk-vcodec 20030000.rkvdec: leakage=5
1722 [ 2.929826] rk-vcodec 20030000.rkvdec: leakage-volt-sel=0
1723 [ 2.929934] rk-vcodec 20030000.rkvdec: Failed to get pvtm
1724 [ 2.930315] rk-vcodec 20030000.rkvdec: avs=0
1725 [ 2.930577] rk-vcodec 20030000.rkvdec: probe device
1726 [ 2.930986] rk-vcodec 20030000.rkvdec: drm allocator with mmu enabled
1727 [ 2.932120] rk-vcodec 20030000.rkvdec: init success
1728 [ 2.933118] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/hdmi-sound[0]'
1729 [ 2.933139] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/hdmi-sound[0]'
1730 [ 2.934032] asoc-simple-card hdmi-sound: i2s-hifi <-> 100c0000.i2s0 mapping ok
1731 [ 2.935701] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]'
1732 [ 2.935723] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]'
1733 [ 2.936652] asoc-simple-card spdif-sound: dit-hifi <-> 100d0000.spdif mapping ok
1734 [ 2.938841] hctosys: unable to open rtc device (rtc0)
1735 [ 2.952163] ALSA device list:
1736 [ 2.952191] #0: DW-I2S-HDMI
1737 [ 2.952200] #1: SPDIF
1738 [ 2.953302] Freeing unused kernel memory: 808K
1739 [ 2.953318] This architecture does not have kernel memory protection.
1740 [ 2.964935] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
1741 [ 3.008966] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
1742 [ 4.072272] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
1743 [ 4.825632] systemd[1]: System time before build time, advancing clock.
1744 [ 4.848081] systemd[1]: Inserted module 'autofs4'
1745 [ 4.853698] ip_tables: (C) 2000-2006 Netfilter Core Team
1746 [ 4.862762] cgroup: cgroup2: unknown option "nsdelegate"
1747 [ 4.877222] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
1748 [ 4.878341] systemd[1]: Detected architecture arm.
1749 [ 4.889759] systemd[1]: Set hostname to <rk322x-box>.
1750 [ 5.062845] ttyS2 - failed to request DMA, use interrupt mode
1751 [ 5.234923] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
1752 [ 5.234968] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
1753 [ 5.652492] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1754 [ 5.677076] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
1755 [ 5.677220] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1756 [ 5.678018] systemd[1]: Listening on Journal Socket (/dev/log).
1757 [ 5.678862] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1758 [ 5.681623] systemd[1]: Created slice User and Session Slice.
1759 [ 5.682278] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1760 [ 5.682668] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
1761 [ 5.683346] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1762 [ 5.684091] systemd[1]: Listening on Journal Socket.
1763 [ 5.685237] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1764 [ 5.691662] systemd[1]: Mounting Kernel Debug File System...
1765 [ 5.692565] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1766 [ 5.698908] systemd[1]: Starting Nameserver information manager...
1767 [ 5.699853] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
1768 [ 5.703647] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1769 [ 5.710999] systemd[1]: Starting Load Kernel Modules...
1770 [ 5.712002] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1771 [ 5.712158] systemd[1]: Reached target Paths.
1772 [ 5.713035] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
1773 [ 5.714056] systemd[1]: Listening on udev Control Socket.
1774 [ 5.716596] systemd[1]: Created slice system-getty.slice.
1775 [ 5.718129] systemd[1]: Listening on udev Kernel Socket.
1776 [ 5.726627] systemd[1]: Starting udev Coldplug all Devices...
1777 [ 5.730725] systemd[1]: Created slice system-serial\x2dgetty.slice.
1778 [ 5.739260] systemd[1]: Mounting POSIX Message Queue File System...
1779 [ 5.740367] systemd[1]: Reached target Slices.
1780 [ 5.752702] systemd[1]: Starting Set the console keyboard layout...
1781 [ 5.753988] systemd[1]: Reached target System Time Synchronized.
1782 [ 5.756479] systemd[1]: Listening on Syslog Socket.
1783 [ 5.769727] systemd[1]: Starting Restore / save the current clock...
1784 [ 5.770996] systemd[1]: Reached target Local Encrypted Volumes.
1785 [ 5.772304] systemd[1]: Reached target Swap.
1786 [ 5.773519] systemd[1]: Reached target Remote File Systems.
1787 [ 5.774695] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
1788 [ 5.777500] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
1789 [ 5.778686] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
1790 [ 5.780225] systemd[1]: Listening on fsck to fsckd communication Socket.
1791 [ 5.781380] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
1792 [ 5.790280] systemd[1]: Starting Remount Root and Kernel File Systems...
1793 [ 5.791968] systemd[1]: Listening on initctl Compatibility Named Pipe.
1794 [ 5.801558] systemd[1]: Starting Create list of required static device nodes for the current kernel...
1795 [ 5.811015] systemd[1]: Mounted Kernel Debug File System.
1796 [ 5.821394] systemd[1]: Started Load Kernel Modules.
1797 [ 5.846467] systemd[1]: Mounted POSIX Message Queue File System.
1798 [ 5.852598] systemd[1]: Started Create list of required static device nodes for the current kernel.
1799 [ 5.858918] systemd[1]: Started Nameserver information manager.
1800 [ 5.871172] systemd[1]: Started Restore / save the current clock.
1801 [ 5.887090] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
1802 [ 5.890866] systemd[1]: Starting Apply Kernel Variables...
1803 [ 5.899201] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
1804 [ 5.907670] systemd[1]: Mounting Kernel Configuration File System...
1805 [ 5.944910] vendor storage:20190527 ret = -1
1806 [ 5.946183] systemd[1]: Started Remount Root and Kernel File Systems.
1807 [ 5.953458] systemd[1]: Mounted Kernel Configuration File System.
1808 [ 5.974461] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
1809 [ 5.980941] systemd[1]: Starting Create System Users...
1810 [ 5.994239] systemd[1]: Starting Load/Save Random Seed...
1811 [ 6.010377] systemd[1]: Started Apply Kernel Variables.
1812 [ 6.066076] systemd[1]: Started Create System Users.
1813 [ 6.075492] systemd[1]: Started Load/Save Random Seed.
1814 [ 6.087933] systemd[1]: Starting Create Static Device Nodes in /dev...
1815 [ 6.171244] systemd[1]: Started Create Static Device Nodes in /dev.
1816 [ 6.182173] systemd[1]: Starting udev Kernel Device Manager...
1817 [ 6.227943] systemd[1]: Started Set the console keyboard layout.
1818 [ 6.234314] systemd[1]: Reached target Local File Systems (Pre).
1819 [ 6.247954] systemd[1]: Mounting /tmp...
1820 [ 6.268045] systemd[1]: Mounted /tmp.
1821 [ 6.276029] systemd[1]: Reached target Local File Systems.
1822 [ 6.282780] systemd[1]: Condition check resulted in Mark the need to relabel after reboot being skipped.
1823 [ 6.283200] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
1824 [ 6.292213] systemd[1]: Starting Armbian ZRAM config...
1825 [ 6.311363] systemd[1]: Starting Set console font and keymap...
1826 [ 6.331789] systemd[1]: Started udev Kernel Device Manager.
1827 [ 6.365376] systemd[1]: Started Set console font and keymap.
1828 [ 6.405915] systemd[1]: Started udev Coldplug all Devices.
1829 [ 6.428070] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
1830 [ 6.484556] systemd[1]: Started Helper to synchronize boot up for ifupdown.
1831 [ 6.501330] systemd[1]: Starting Raise network interfaces...
1832 [ 6.646941] zram: Added device: zram0
1833 [ 6.650419] zram: Added device: zram1
1834 [ 6.655207] zram: Added device: zram2
1835 [ 6.707878] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '22:00:07', on 'May 6 2021'.
1836 [ 6.708138] mali-utgard 20001000.gpu: mali_platform_device->num_resources = 13
1837 [ 6.708158] mali-utgard 20001000.gpu: resource[0].start = 0x0x20001000
1838 [ 6.708170] mali-utgard 20001000.gpu: resource[1].start = 0x0x20000000
1839 [ 6.708180] mali-utgard 20001000.gpu: resource[2].start = 0x0x20003000
1840 [ 6.708190] mali-utgard 20001000.gpu: resource[3].start = 0x0x20008000
1841 [ 6.708200] mali-utgard 20001000.gpu: resource[4].start = 0x0x20004000
1842 [ 6.708210] mali-utgard 20001000.gpu: resource[5].start = 0x0x2000a000
1843 [ 6.708220] mali-utgard 20001000.gpu: resource[6].start = 0x0x20005000
1844 [ 6.708230] mali-utgard 20001000.gpu: resource[7].start = 0x0x00000020
1845 [ 6.708246] mali-utgard 20001000.gpu: resource[8].start = 0x0x00000021
1846 [ 6.708263] mali-utgard 20001000.gpu: resource[9].start = 0x0x00000022
1847 [ 6.708273] mali-utgard 20001000.gpu: resource[10].start = 0x0x00000021
1848 [ 6.708282] mali-utgard 20001000.gpu: resource[11].start = 0x0x00000022
1849 [ 6.708293] mali-utgard 20001000.gpu: resource[12].start = 0x0x00000021
1850 [ 6.708304] D : [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 623; [Func] : mali_platform_device_init(); to add platform_specific_data to platform_device_of_mali.
1851 [ 6.708580] mali-utgard 20001000.gpu: leakage=5
1852 [ 6.708608] mali-utgard 20001000.gpu: leakage-volt-sel=0
1853 [ 6.708714] mali-utgard 20001000.gpu: Failed to get pvtm
1854 [ 6.709307] mali-utgard 20001000.gpu: avs=0
1855 [ 6.709674] mali-utgard 20001000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
1856 [ 6.718545] Mali: Mali device driver loaded
1857 [ 6.726957] systemd[1]: Found device /dev/ttyS2.
1858 [ 6.728437] rk3228-codec 12010000.codec: GPIO lookup for consumer spk-en
1859 [ 6.728444] rk3228-codec 12010000.codec: using device tree for GPIO lookup
1860 [ 6.728453] of_get_named_gpiod_flags: can't parse 'spk-en-gpios' property of node '/codec@12010000[0]'
1861 [ 6.728483] of_get_named_gpiod_flags: parsed 'spk-en-gpio' property of node '/codec@12010000[0]' - status (0)
1862 [ 6.728535] rk3228-codec 12010000.codec: spk_depop_time use default value.
1863 [ 6.733468] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound[0]'
1864 [ 6.733476] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound[0]'
1865 [ 6.760145] asoc-simple-card sound: rk3228-hifi <-> 100b0000.i2s1 mapping ok
1866 [ 6.809012] devfreq 20001000.gpu: Couldn't update frequency transition information.
1867 [ 6.903195] gpio_ir_recv ir-receiver: GPIO lookup for consumer (null)
1868 [ 6.903233] gpio_ir_recv ir-receiver: using device tree for GPIO lookup
1869 [ 6.903291] of_get_named_gpiod_flags: parsed 'gpios' property of node '/ir-receiver[0]' - status (0)
1870 [ 6.903429] Registered IR keymap rc-rktvbox
1871 [ 6.903698] rc rc1: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1
1872 [ 6.904275] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1/input1
1873 [ 7.093272] zram0: detected capacity change from 0 to 504537088
1874 [ 7.435941] systemd[1]: Started Raise network interfaces.
1875 [ 7.550331] systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
1876 [ 7.555428] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
1877 [ 7.555983] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
1878 [ 7.556459] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
1879 [ 7.556673] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
1880 [ 7.557195] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
1881 [ 7.557431] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
1882 [ 7.557561] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
1883 [ 7.557874] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
1884 [ 7.862425] cfg80211: World regulatory domain updated:
1885 [ 7.862456] cfg80211: DFS Master region: unset
1886 [ 7.862467] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
1887 [ 7.862485] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
1888 [ 7.862502] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
1889 [ 7.862515] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
1890 [ 7.862531] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
1891 [ 7.862546] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
1892 [ 7.862560] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
1893 [ 7.862574] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
1894 [ 7.862587] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
1895 [ 8.174155] Adding 492708k swap on /dev/zram0. Priority:5 extents:1 across:492708k SS
1896 [ 8.403888] zram1: detected capacity change from 0 to 52428800
1897 [ 10.495965] systemd[1]: Started Armbian ZRAM config.
1898 [ 10.514681] systemd[1]: Starting Armbian memory supported logging...
1899 [ 10.639460] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
1900 [ 14.202643] systemd[1]: Started Armbian memory supported logging.
1901 [ 14.216753] systemd[1]: Starting Journal Service...
1902 [ 14.625873] systemd[1]: Started Journal Service.
1903 [ 14.697141] systemd-journald[574]: Received request to flush runtime journal from PID 1
1904
1905 ### armbian-release:
1906
1907 # PLEASE DO NOT EDIT THIS FILE
1908 BOARD=rk322x-box
1909 BOARD_NAME="rk322x-box"
1910 BOARDFAMILY=rk322x
1911 BUILD_REPOSITORY_URL=git@github.com:armbian/build.git
1912 BUILD_REPOSITORY_COMMIT=08297378c-dirty
1913 DISTRIBUTION_CODENAME=buster
1914 DISTRIBUTION_STATUS=supported
1915 VERSION=21.05.1
1916 LINUXFAMILY=rk322x
1917 ARCH=arm
1918 IMAGE_TYPE=stable
1919 BOARD_TYPE=tvb
1920 INITRD_ARCH=arm
1921 KERNEL_IMAGE_TYPE=Image
1922
1923 ### boot environment:
1924
1925 verbosity=1
1926 extraargs=coherent_pool=2M
1927 bootlogo=false
1928 overlay_prefix=rk322x
1929 fdtfile=rk322x-box.dtb
1930 rootdev=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
1931 rootfstype=ext4
1932 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u
1933
1934 ### lsusb:
1935
1936 Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
1937 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
1938 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
1939 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
1940 Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
1941 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
1942 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
1943
1944 ### lscpu:
1945
1946 Architecture: armv7l
1947 Byte Order: Little Endian
1948 CPU(s): 4
1949 On-line CPU(s) list: 0-3
1950 Thread(s) per core: 1
1951 Core(s) per socket: 4
1952 Socket(s): 1
1953 Vendor ID: ARM
1954 Model: 5
1955 Model name: Cortex-A7
1956 Stepping: r0p5
1957 CPU max MHz: 1200.0000
1958 CPU min MHz: 408.0000
1959 BogoMIPS: 70.58
1960 Flags: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
1961
1962 ### cpuinfo:
1963
1964 processor : 0
1965 model name : ARMv7 Processor rev 5 (v7l)
1966 BogoMIPS : 70.58
1967 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
1968 CPU implementer : 0x41
1969 CPU architecture: 7
1970 CPU variant : 0x0
1971 CPU part : 0xc07
1972 CPU revision : 5
1973
1974 processor : 1
1975 model name : ARMv7 Processor rev 5 (v7l)
1976 BogoMIPS : 70.58
1977 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
1978 CPU implementer : 0x41
1979 CPU architecture: 7
1980 CPU variant : 0x0
1981 CPU part : 0xc07
1982 CPU revision : 5
1983
1984 processor : 2
1985 model name : ARMv7 Processor rev 5 (v7l)
1986 BogoMIPS : 70.58
1987 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
1988 CPU implementer : 0x41
1989 CPU architecture: 7
1990 CPU variant : 0x0
1991 CPU part : 0xc07
1992 CPU revision : 5
1993
1994 processor : 3
1995 model name : ARMv7 Processor rev 5 (v7l)
1996 BogoMIPS : 70.58
1997 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
1998 CPU implementer : 0x41
1999 CPU architecture: 7
2000 CPU variant : 0x0
2001 CPU part : 0xc07
2002 CPU revision : 5
2003
2004 Hardware : Generic DT based system
2005 Revision : 0000
2006 Serial : cd1d5ffa03aecfa2
2007
2008 ### meminfo:
2009
2010 MemTotal: 985420 kB
2011 MemFree: 905472 kB
2012 MemAvailable: 931444 kB
2013 Buffers: 8720 kB
2014 Cached: 29232 kB
2015 SwapCached: 0 kB
2016 Active: 27008 kB
2017 Inactive: 16840 kB
2018 Active(anon): 6112 kB
2019 Inactive(anon): 5708 kB
2020 Active(file): 20896 kB
2021 Inactive(file): 11132 kB
2022 Unevictable: 0 kB
2023 Mlocked: 0 kB
2024 HighTotal: 0 kB
2025 HighFree: 0 kB
2026 LowTotal: 985420 kB
2027 LowFree: 905472 kB
2028 SwapTotal: 492708 kB
2029 SwapFree: 492708 kB
2030 Dirty: 1276 kB
2031 Writeback: 0 kB
2032 AnonPages: 5988 kB
2033 Mapped: 7952 kB
2034 Shmem: 5836 kB
2035 Slab: 18256 kB
2036 SReclaimable: 9972 kB
2037 SUnreclaim: 8284 kB
2038 KernelStack: 928 kB
2039 PageTables: 232 kB
2040 NFS_Unstable: 0 kB
2041 Bounce: 0 kB
2042 WritebackTmp: 0 kB
2043 CommitLimit: 985416 kB
2044 Committed_AS: 21552 kB
2045 VmallocTotal: 245760 kB
2046 VmallocUsed: 0 kB
2047 VmallocChunk: 0 kB
2048 CmaTotal: 16384 kB
2049 CmaFree: 12204 kB
2050
2051 ### virtual memory:
2052
2053 vm.admin_reserve_kbytes = 8192
2054 vm.block_dump = 0
2055 vm.dirty_background_bytes = 0
2056 vm.dirty_background_ratio = 10
2057 vm.dirty_bytes = 0
2058 vm.dirty_expire_centisecs = 3000
2059 vm.dirty_ratio = 20
2060 vm.dirtytime_expire_seconds = 43200
2061 vm.dirty_writeback_centisecs = 500
2062 vm.drop_caches = 0
2063 vm.extra_free_kbytes = 0
2064 vm.highmem_is_dirtyable = 0
2065 vm.laptop_mode = 0
2066 vm.legacy_va_layout = 0
2067 vm.lowmem_reserve_ratio = 32 32
2068 vm.max_map_count = 65530
2069 vm.min_free_kbytes = 3924
2070 vm.mmap_min_addr = 32768
2071 vm.mmap_rnd_bits = 8
2072 vm.nr_pdflush_threads = 0
2073 vm.oom_dump_tasks = 1
2074 vm.oom_kill_allocating_task = 0
2075 vm.overcommit_kbytes = 0
2076 vm.overcommit_memory = 0
2077 vm.overcommit_ratio = 50
2078 vm.page-cluster = 0
2079 vm.panic_on_oom = 0
2080 vm.percpu_pagelist_fraction = 0
2081 vm.stat_interval = 1
2082 vm.swappiness = 100
2083 vm.user_reserve_kbytes = 30422
2084 vm.vfs_cache_pressure = 100
2085
2086 ### ip addr:
2087
2088 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
2089 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2090 inet XXX.XXX.0.1/8 scope host lo
2091 valid_lft forever preferred_lft forever
2092 inet6 ::1/128 scope host
2093 valid_lft forever preferred_lft forever
2094 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
2095 link/ether f2:16:49:d5:79:1e brd ff:ff:ff:ff:ff:ff
2096 3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
2097 link/ether f6:b4:e0:5a:1e:3a brd ff:ff:ff:ff:ff:ff
2098 4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1
2099 link/sit XXX.XXX.0.0 brd XXX.XXX.0.0
2100
2101 ### partitions:
2102
2103 major minor #blocks name
2104
2105 179 0 60620800 mmcblk0
2106 179 1 60010496 mmcblk0p1
2107 253 0 492712 zram0
2108 253 1 51200 zram1
2109
2110 ### df:
2111
2112 udev 471M 0 471M 0% /dev
2113 tmpfs 97M 2.8M 94M 3% /run
2114 /dev/mmcblk0p1 56G 1.1G 55G 2% /
2115 tmpfs 482M 0 482M 0% /dev/shm
2116 tmpfs 5.0M 4.0K 5.0M 1% /run/lock
2117 tmpfs 482M 0 482M 0% /sys/fs/cgroup
2118 tmpfs 482M 0 482M 0% /tmp
2119 /dev/zram1 49M 1.3M 44M 3% /var/log
2120
2121 ### lsblk:
2122
2123 NAME FSTYPE SIZE MOUNTPOINT UUID
2124 mmcblk0 57.8G
2125 └─mmcblk0p1 ext4 57.2G / 2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
2126 zram1 50M /var/log
2127
2128 ### zramctl:
2129
2130 NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT
2131 /dev/zram1 lz4 50M 132K 868B 32K 4 /var/log
2132 /dev/zram0 lzo 481.2M 4K 76B 4K 4 [SWAP]
2133
2134 ### mtab:
2135
2136 /dev/mmcblk0p1 / ext4 rw,noatime,errors=remount-ro,commit=600 0 0
2137 /dev/mmcblk0p1 /var/log.hdd ext4 rw,noatime,errors=remount-ro,commit=600 0 0
2138 /dev/zram1 /var/log ext4 rw,relatime,discard 0 0
2139
2140 ### mmc0:59b4 info:
2141
2142 cid: 1d41445344202020100000002c015287
2143 csd: 400e00325b590001ce7f7f800a4000cf
2144 scr: 0245804300000000
2145 date: 02/2021
2146 name: SD
2147 type: SD
2148 preferred_erase_size: 4194304
2149 fwrev: 0x0
2150 hwrev: 0x1
2151 oemid: 0x4144
2152 manfid: 0x00001d
2153 serial: 0x0000002c
2154 uevent: DRIVER=mmcblk MMC_TYPE=SD MMC_NAME=SD MODALIAS=mmc:block
2155 erase_size: 512
2156
2157 ### Boot system health:
2158
2159 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St.
2160 20:33:25: 1200MHz 1.28 38% 21% 14% 0% 2% 0% 45.8°C 0/4
2161 20:33:25: 1200MHz 1.28 56% 23% 31% 1% 0% 0% 45.0°C 0/4
2162 20:33:26: 816MHz 1.28 34% 20% 12% 1% 0% 0% 43.0°C 0/4
2163 20:33:26: 1008MHz 1.28 33% 19% 11% 1% 0% 0% 43.0°C 0/4
2164 20:33:27: 816MHz 1.28 34% 18% 14% 2% 0% 0% 43.0°C 0/4
2165
2166 ### Activated 1 lzo zram swap devices with 481 MB each
2167
2168 ### Activated Armbian ramlog partition with lz4 compression
2169
2170 Thu 03 Jun 2021 10:37:05 PM UTC | rk322x-box | 21.05.1 | armhf | armv7l | 4.4.194-rk322x
2171
2172 ### dmesg:
2173
2174 [ 0.000000] Booting Linux on physical CPU 0xf00
2175 [ 0.000000] Initializing cgroup subsys cpuset
2176 [ 0.000000] Initializing cgroup subsys cpu
2177 [ 0.000000] Initializing cgroup subsys cpuacct
2178 [ 0.000000] Linux version 4.4.194-rk322x (root@hirsute) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) ) #3 SMP Thu May 6 22:00:38 UTC 2021
2179 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
2180 [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
2181 [ 0.000000] Machine model: Generic RK322x TV Box board
2182 [ 0.000000] cma: Reserved 16 MiB at 0x9f000000
2183 [ 0.000000] Memory policy: Data cache writealloc
2184 [ 0.000000] On node 0 totalpages: 253952
2185 [ 0.000000] free_area_init_node: node 0, pgdat b1253b40, node_mem_map ee6f1000
2186 [ 0.000000] Normal zone: 2304 pages used for memmap
2187 [ 0.000000] Normal zone: 0 pages reserved
2188 [ 0.000000] Normal zone: 253952 pages, LIFO batch:31
2189 [ 0.000000] psci: probing for conduit method from DT.
2190 [ 0.000000] psci: PSCIv1.0 detected in firmware.
2191 [ 0.000000] psci: Using standard PSCI v0.2 function IDs
2192 [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
2193 [ 0.000000] PERCPU: Embedded 14 pages/cpu @ee68f000 s24856 r8192 d24296 u57344
2194 [ 0.000000] pcpu-alloc: s24856 r8192 d24296 u57344 alloc=14*4096
2195 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
2196 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251648
2197 [ 0.000000] Kernel command line: earlyprintk root=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db console=ttyS2,115200n8 console=tty1 rootwait rootfstype=ext4 consoleblank=0 loglevel=1 ubootpart=73c5b759-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u coherent_pool=2M cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
2198 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
2199 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
2200 [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
2201 [ 0.000000] Memory: 962664K/1015808K available (12862K kernel code, 919K rwdata, 3240K rodata, 808K init, 1219K bss, 36760K reserved, 16384K cma-reserved, 0K highmem)
2202 [ 0.000000] Virtual kernel memory layout:
2203 vector : 0xffff0000 - 0xffff1000 ( 4 kB)
2204 fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
2205 vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
2206 lowmem : 0xb0000000 - 0xf0000000 (1024 MB)
2207 pkmap : 0xafe00000 - 0xb0000000 ( 2 MB)
2208 modules : 0xaf000000 - 0xafe00000 ( 14 MB)
2209 .text : 0xb0008000 - 0xb0c97c6c (12864 kB)
2210 .init : 0xb10b0000 - 0xb117a000 ( 808 kB)
2211 .data : 0xb117a000 - 0xb125fe94 ( 920 kB)
2212 .bss : 0xb1261000 - 0xb1391f14 (1220 kB)
2213 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
2214 [ 0.000000] Hierarchical RCU implementation.
2215 [ 0.000000] Build-time adjustment of leaf fanout to 32.
2216 [ 0.000000] NR_IRQS:16 nr_irqs:16 16
2217 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
2218 [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
2219 [ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
2220 [ 0.000023] Switching to timer-based delay loop, resolution 41ns
2221 [ 0.001792] Console: colour dummy device 80x30
2222 [ 0.001976] console [tty1] enabled
2223 [ 0.002001] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
2224 [ 0.002018] pid_max: default: 32768 minimum: 301
2225 [ 0.002150] Security Framework initialized
2226 [ 0.002164] Yama: becoming mindful.
2227 [ 0.002239] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
2228 [ 0.002255] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
2229 [ 0.003142] Initializing cgroup subsys io
2230 [ 0.003175] Initializing cgroup subsys memory
2231 [ 0.003217] Initializing cgroup subsys devices
2232 [ 0.003237] Initializing cgroup subsys freezer
2233 [ 0.003254] Initializing cgroup subsys net_cls
2234 [ 0.003271] Initializing cgroup subsys perf_event
2235 [ 0.003289] Initializing cgroup subsys net_prio
2236 [ 0.003318] Initializing cgroup subsys pids
2237 [ 0.003386] CPU: Testing write buffer coherency: ok
2238 [ 0.003434] ftrace: allocating 41892 entries in 123 pages
2239 [ 0.082718] /cpus/cpu@f00 missing clock-frequency property
2240 [ 0.082751] /cpus/cpu@f01 missing clock-frequency property
2241 [ 0.082770] /cpus/cpu@f02 missing clock-frequency property
2242 [ 0.082789] /cpus/cpu@f03 missing clock-frequency property
2243 [ 0.082802] CPU0: update cpu_capacity 430
2244 [ 0.082813] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
2245 [ 0.082895] Setting up static identity map for 0x60008280 - 0x600082d8
2246 [ 0.094098] CPU1: update cpu_capacity 430
2247 [ 0.094107] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
2248 [ 0.103563] CPU2: update cpu_capacity 430
2249 [ 0.103572] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
2250 [ 0.113014] CPU3: update cpu_capacity 430
2251 [ 0.113021] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
2252 [ 0.113154] Brought up 4 CPUs
2253 [ 0.113194] SMP: Total of 4 processors activated (192.00 BogoMIPS).
2254 [ 0.113203] CPU: All CPU(s) started in SVC mode.
2255 [ 0.114720] devtmpfs: initialized
2256 [ 0.134345] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
2257 [ 0.134927] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
2258 [ 0.134968] futex hash table entries: 1024 (order: 4, 65536 bytes)
2259 [ 0.136300] xor: measuring software checksum speed
2260 [ 0.174743] arm4regs : 1011.000 MB/sec
2261 [ 0.214847] 8regs : 705.000 MB/sec
2262 [ 0.254950] 32regs : 684.000 MB/sec
2263 [ 0.295051] neon : 1018.000 MB/sec
2264 [ 0.295061] xor: using function: neon (1018.000 MB/sec)
2265 [ 0.295101] pinctrl core: initialized pinctrl subsystem
2266 [ 0.296656] NET: Registered protocol family 16
2267 [ 0.299187] DMA: preallocated 2048 KiB pool for atomic coherent allocations
2268 [ 0.311205] cpuidle: using governor ladder
2269 [ 0.323217] cpuidle: using governor menu
2270 [ 0.339630] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0
2271 [ 0.339792] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1
2272 [ 0.339953] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2
2273 [ 0.340104] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3
2274 [ 0.346648] console [pstore-1] enabled
2275 [ 0.346660] pstore: Registered ramoops as persistent store backend
2276 [ 0.346672] ramoops: attached 0xf0000@0x62e00000, ecc: 0/0
2277 [ 0.350043] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
2278 [ 0.350064] hw-breakpoint: maximum watchpoint size is 8 bytes.
2279 [ 0.350273] sip_firmware_init: set rockchip sip version v2 failed
2280 [ 0.448073] raid6: int32x1 gen() 133 MB/s
2281 [ 0.516162] raid6: int32x1 xor() 131 MB/s
2282 [ 0.584418] raid6: int32x2 gen() 166 MB/s
2283 [ 0.652687] raid6: int32x2 xor() 137 MB/s
2284 [ 0.720838] raid6: int32x4 gen() 163 MB/s
2285 [ 0.788992] raid6: int32x4 xor() 137 MB/s
2286 [ 0.857228] raid6: int32x8 gen() 166 MB/s
2287 [ 0.925497] raid6: int32x8 xor() 113 MB/s
2288 [ 0.993623] raid6: neonx1 gen() 382 MB/s
2289 [ 1.061750] raid6: neonx1 xor() 290 MB/s
2290 [ 1.129947] raid6: neonx2 gen() 519 MB/s
2291 [ 1.198094] raid6: neonx2 xor() 376 MB/s
2292 [ 1.266296] raid6: neonx4 gen() 581 MB/s
2293 [ 1.334511] raid6: neonx4 xor() 400 MB/s
2294 [ 1.402798] raid6: neonx8 gen() 560 MB/s
2295 [ 1.470954] raid6: neonx8 xor() 391 MB/s
2296 [ 1.470966] raid6: using algorithm neonx4 gen() 581 MB/s
2297 [ 1.470976] raid6: .... xor() 400 MB/s, rmw enabled
2298 [ 1.470986] raid6: using intx1 recovery algorithm
2299 [ 1.471964] rockchip-pm rockchip-suspend: not set wakeup-config
2300 [ 1.471988] rockchip-pm rockchip-suspend: not set pwm-regulator-config
2301 [ 1.472350] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@0[0]'
2302 [ 1.472838] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulators/regulator@1[0]'
2303 [ 1.473475] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc-host-regulator[0]' - status (0)
2304 [ 1.474074] of_get_named_gpiod_flags: parsed 'gpio' property of node '/otg-vbus-regulator[0]' - status (0)
2305 [ 1.474568] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]'
2306 [ 1.475480] iommu: Adding device 20020000.vpu-service to group 0
2307 [ 1.475602] iommu: Adding device 20030000.rkvdec to group 1
2308 [ 1.475698] iommu: Adding device 20050000.vop to group 2
2309 [ 1.475791] iommu: Adding device 20070000.iep to group 3
2310 [ 1.476314] rk_iommu 20020800.iommu: can't get sclk
2311 [ 1.476889] rk_iommu 20030480.iommu: can't get sclk
2312 [ 1.477146] rk_iommu 20053f00.iommu: can't get sclk
2313 [ 1.477291] rk_iommu 20070800.iommu: can't get aclk
2314 [ 1.477310] rk_iommu 20070800.iommu: can't get hclk
2315 [ 1.477326] rk_iommu 20070800.iommu: can't get sclk
2316 [ 1.478077] SCSI subsystem initialized
2317 [ 1.478490] usbcore: registered new interface driver usbfs
2318 [ 1.478591] usbcore: registered new interface driver hub
2319 [ 1.478709] usbcore: registered new device driver usb
2320 [ 1.478929] media: Linux media interface: v0.10
2321 [ 1.479086] Linux video capture interface: v2.00
2322 [ 1.479340] pps_core: LinuxPPS API ver. 1 registered
2323 [ 1.479355] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
2324 [ 1.479397] PTP clock support registered
2325 [ 1.481305] Advanced Linux Sound Architecture Driver Initialized.
2326 [ 1.482296] Bluetooth: Core ver 2.21
2327 [ 1.482365] NET: Registered protocol family 31
2328 [ 1.482378] Bluetooth: HCI device and connection manager initialized
2329 [ 1.482399] Bluetooth: HCI socket layer initialized
2330 [ 1.482416] Bluetooth: L2CAP socket layer initialized
2331 [ 1.482471] Bluetooth: SCO socket layer initialized
2332 [ 1.483320] NetLabel: Initializing
2333 [ 1.483341] NetLabel: domain hash size = 128
2334 [ 1.483350] NetLabel: protocols = UNLABELED CIPSOv4
2335 [ 1.483425] NetLabel: unlabeled traffic allowed by default
2336 [ 1.484764] clocksource: Switched to clocksource arch_sys_counter
2337 [ 1.579751] NET: Registered protocol family 2
2338 [ 1.580616] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
2339 [ 1.580732] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
2340 [ 1.581168] TCP: Hash tables configured (established 8192 bind 8192)
2341 [ 1.581265] UDP hash table entries: 512 (order: 2, 24576 bytes)
2342 [ 1.581334] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
2343 [ 1.581684] NET: Registered protocol family 1
2344 [ 1.582353] RPC: Registered named UNIX socket transport module.
2345 [ 1.582376] RPC: Registered udp transport module.
2346 [ 1.582387] RPC: Registered tcp transport module.
2347 [ 1.582397] RPC: Registered tcp NFSv4.1 backchannel transport module.
2348 [ 1.582718] Trying to unpack rootfs image as initramfs...
2349 [ 1.955842] Freeing initrd memory: 5564K
2350 [ 1.956989] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
2351 [ 1.959892] Initialise system trusted keyring
2352 [ 1.973812] VFS: Disk quotas dquot_6.6.0
2353 [ 1.974119] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
2354 [ 1.976802] squashfs: version 4.0 (2009/01/31) Phillip Lougher
2355 [ 1.980139] NFS: Registering the id_resolver key type
2356 [ 1.980230] Key type id_resolver registered
2357 [ 1.980242] Key type id_legacy registered
2358 [ 1.980278] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
2359 [ 1.980389] ntfs: driver 2.1.32 [Flags: R/W].
2360 [ 1.981436] JFS: nTxBlock = 7692, nTxLock = 61538
2361 [ 1.990031] SGI XFS with security attributes, no debug enabled
2362 [ 1.998857] NET: Registered protocol family 38
2363 [ 1.998908] Key type asymmetric registered
2364 [ 1.998929] Asymmetric key parser 'x509' registered
2365 [ 1.999327] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
2366 [ 1.999702] io scheduler noop registered
2367 [ 1.999731] io scheduler deadline registered
2368 [ 1.999832] io scheduler cfq registered (default)
2369 [ 2.003035] phy phy-11000000.syscon:usb2-phy@800.2: Failed to get VBUS supply regulator
2370 [ 2.008053] rk-vcodec 20020000.vpu-service: no regulator for vcodec
2371 [ 2.008451] rk-vcodec 20020000.vpu-service: probe device
2372 [ 2.008928] rk-vcodec 20020000.vpu-service: drm allocator with mmu enabled
2373 [ 2.010127] rk-vcodec 20020000.vpu-service: could not find power_model node
2374 [ 2.010153] rk-vcodec 20020000.vpu-service: init success
2375 [ 2.010596] rk-vcodec 20030000.rkvdec: vcodec regulator not ready, retry
2376 [ 2.014832] dma-pl330 110f0000.pdma: Loaded driver for PL330 DMAC-241330
2377 [ 2.014859] dma-pl330 110f0000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
2378 [ 2.015962] rockchip-system-monitor rockchip-system-monitor: system monitor probe
2379 [ 2.016426] pwm-regulator vdd-arm-regulator: GPIO lookup for consumer enable
2380 [ 2.016444] pwm-regulator vdd-arm-regulator: using device tree for GPIO lookup
2381 [ 2.016461] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-arm-regulator[0]'
2382 [ 2.016477] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-arm-regulator[0]'
2383 [ 2.016490] pwm-regulator vdd-arm-regulator: using lookup tables for GPIO lookup
2384 [ 2.016505] pwm-regulator vdd-arm-regulator: lookup for GPIO enable failed
2385 [ 2.017208] pwm-regulator vdd-log-regulator: GPIO lookup for consumer enable
2386 [ 2.017231] pwm-regulator vdd-log-regulator: using device tree for GPIO lookup
2387 [ 2.017247] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log-regulator[0]'
2388 [ 2.017261] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log-regulator[0]'
2389 [ 2.017275] pwm-regulator vdd-log-regulator: using lookup tables for GPIO lookup
2390 [ 2.017290] pwm-regulator vdd-log-regulator: lookup for GPIO enable failed
2391 [ 2.018346] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
2392 [ 2.019147] 11030000.serial: ttyS2 at MMIO 0x11030000 (irq = 30, base_baud = 1500000) is a 16550A
2393 [ 2.019973] console [ttyS2] enabled
2394 [ 2.021808] [drm] Initialized drm 1.1.0 20060810
2395 [ 2.024178] [drm] Rockchip DRM driver version: v1.0.1
2396 [ 2.024432] rockchip-drm display-subsystem: devfreq is not set
2397 [ 2.025216] rockchip-drm display-subsystem: bound 20050000.vop (ops 0xb0d1b2b0)
2398 [ 2.025614] i2c i2c-0: of_i2c: modalias failure on /hdmi@200a0000/ports
2399 [ 2.025641] dwhdmi-rockchip 200a0000.hdmi: registered DesignWare HDMI I2C bus driver
2400 [ 2.025761] dwhdmi-rockchip 200a0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (inno_dw_hdmi_phy)
2401 [ 2.026998] rockchip-drm display-subsystem: bound 200a0000.hdmi (ops 0xb0d13808)
2402 [ 2.027022] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
2403 [ 2.027034] [drm] No driver support for vblank timestamp query.
2404 [ 2.027148] rockchip-drm display-subsystem: failed to parse display resources
2405 [ 2.027211] rockchip-drm display-subsystem: No connectors reported connected with modes
2406 [ 2.027295] [drm] Cannot find any crtc or sizes - going 1024x768
2407 [ 2.049574] Console: switching to colour frame buffer device 128x48
2408 [ 2.064926] rockchip-drm display-subsystem: fb0: frame buffer device
2409 [ 2.081300] Registered IR keymap rc-cec
2410 [ 2.081555] rc rc0: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0
2411 [ 2.082225] input: RC for dw_hdmi as /devices/platform/200a0000.hdmi/rc/rc0/input0
2412 [ 2.084363] brd: module loaded
2413 [ 2.095588] loop: module loaded
2414 [ 2.095679] lkdtm: No crash points registered, enable through debugfs
2415 [ 2.098200] libphy: Fixed MDIO Bus: probed
2416 [ 2.098233] tun: Universal TUN/TAP device driver, 1.6
2417 [ 2.098244] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
2418 [ 2.098599] CAN device driver interface
2419 [ 2.099947] rk_gmac-dwmac 30200000.ethernet: clock input or output? (output).
2420 [ 2.099975] rk_gmac-dwmac 30200000.ethernet: TX delay(0x30).
2421 [ 2.099990] rk_gmac-dwmac 30200000.ethernet: RX delay(0x10).
2422 [ 2.100047] rk_gmac-dwmac 30200000.ethernet: integrated PHY? (yes).
2423 [ 2.100219] rk_gmac-dwmac 30200000.ethernet: cannot get clock clk_mac_speed
2424 [ 2.105298] rk_gmac-dwmac 30200000.ethernet: init for RMII
2425 [ 2.140889] stmmac - user ID: 0x10, Synopsys ID: 0x35
2426 [ 2.140906] Ring mode enabled
2427 [ 2.140916] DMA HW capability register supported
2428 [ 2.140926] Normal descriptors
2429 [ 2.140937] RX Checksum Offload Engine supported (type 2)
2430 [ 2.140946] TX Checksum insertion supported
2431 [ 2.140954] Wake-Up On Lan supported
2432 [ 2.141049] rk_gmac-dwmac 30200000.ethernet: rk_get_eth_addr: mac address: f6:b4:e0:5a:1e:3a
2433 [ 2.141062] eth%d: device MAC address f6:b4:e0:5a:1e:3a
2434 [ 2.141072] Enable RX Mitigation via HW Watchdog Timer
2435 [ 2.141267] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@30200000[0]' - status (0)
2436 [ 2.546294] libphy: stmmac: probed
2437 [ 2.546324] eth%d: PHY ID 1234d400 at 0 IRQ POLL (stmmac-0:00) active
2438 [ 2.546338] eth%d: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
2439 [ 2.546351] eth%d: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
2440 [ 2.546364] eth%d: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
2441 [ 2.546376] eth%d: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
2442 [ 2.546388] eth%d: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
2443 [ 2.546401] eth%d: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
2444 [ 2.546413] eth%d: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
2445 [ 2.546425] eth%d: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
2446 [ 2.546437] eth%d: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
2447 [ 2.546450] eth%d: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
2448 [ 2.546462] eth%d: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
2449 [ 2.546475] eth%d: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
2450 [ 2.546487] eth%d: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
2451 [ 2.546500] eth%d: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
2452 [ 2.546512] eth%d: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
2453 [ 2.546524] eth%d: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
2454 [ 2.546536] eth%d: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
2455 [ 2.546549] eth%d: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
2456 [ 2.546561] eth%d: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
2457 [ 2.546574] eth%d: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
2458 [ 2.546586] eth%d: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
2459 [ 2.546598] eth%d: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
2460 [ 2.546611] eth%d: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
2461 [ 2.546623] eth%d: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
2462 [ 2.546635] eth%d: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
2463 [ 2.546648] eth%d: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
2464 [ 2.546660] eth%d: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
2465 [ 2.546672] eth%d: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
2466 [ 2.546684] eth%d: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
2467 [ 2.546696] eth%d: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
2468 [ 2.546708] eth%d: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
2469 [ 2.548146] PPP generic driver version 2.4.2
2470 [ 2.548542] Atmel at76x USB Wireless LAN Driver 0.17 loading
2471 [ 2.548681] usbcore: registered new interface driver at76c50x-usb
2472 [ 2.548887] usbcore: registered new interface driver rtl8187
2473 [ 2.549012] usbcore: registered new interface driver rndis_wlan
2474 [ 2.549122] usbcore: registered new interface driver zd1201
2475 [ 2.549500] usbcore: registered new interface driver rt2800usb
2476 [ 2.549628] Rockchip WiFi SYS interface (V1.00) ...
2477 [ 2.549698] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
2478 [ 2.549784] usbcore: registered new interface driver pegasus
2479 [ 2.549871] usbcore: registered new interface driver rtl8150
2480 [ 2.549955] usbcore: registered new interface driver r8152
2481 [ 2.550056] usbcore: registered new interface driver asix
2482 [ 2.550138] usbcore: registered new interface driver ax88179_178a
2483 [ 2.550219] usbcore: registered new interface driver cdc_ether
2484 [ 2.550311] usbcore: registered new interface driver dm9601
2485 [ 2.550419] usbcore: registered new interface driver smsc75xx
2486 [ 2.550526] usbcore: registered new interface driver smsc95xx
2487 [ 2.550608] usbcore: registered new interface driver net1080
2488 [ 2.550690] usbcore: registered new interface driver rndis_host
2489 [ 2.550774] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
2490 [ 2.550913] usbcore: registered new interface driver cdc_ncm
2491 [ 2.551006] usbcore: registered new interface driver cdc_mbim
2492 [ 2.551481] 30040000.usb supply vusb_d not found, using dummy regulator
2493 [ 2.551579] 30040000.usb supply vusb_a not found, using dummy regulator
2494 [ 2.564723] dwc2 30040000.usb: DWC OTG Controller
2495 [ 2.564835] dwc2 30040000.usb: new USB bus registered, assigned bus number 1
2496 [ 2.564895] dwc2 30040000.usb: irq 48, io mem 0x30040000
2497 [ 2.565264] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
2498 [ 2.565282] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
2499 [ 2.565296] usb usb1: Product: DWC OTG Controller
2500 [ 2.565310] usb usb1: Manufacturer: Linux 4.4.194-rk322x dwc2_hsotg
2501 [ 2.565323] usb usb1: SerialNumber: 30040000.usb
2502 [ 2.566309] hub 1-0:1.0: USB hub found
2503 [ 2.566382] hub 1-0:1.0: 1 port detected
2504 [ 2.567890] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
2505 [ 2.567919] ehci-platform: EHCI generic platform driver
2506 [ 2.570433] ehci-platform 30080000.usb: EHCI Host Controller
2507 [ 2.570799] ehci-platform 30080000.usb: new USB bus registered, assigned bus number 2
2508 [ 2.571097] ehci-platform 30080000.usb: irq 49, io mem 0x30080000
2509 [ 2.580807] ehci-platform 30080000.usb: USB 2.0 started, EHCI 1.00
2510 [ 2.581149] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
2511 [ 2.581168] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
2512 [ 2.581182] usb usb2: Product: EHCI Host Controller
2513 [ 2.581196] usb usb2: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
2514 [ 2.581210] usb usb2: SerialNumber: 30080000.usb
2515 [ 2.582183] hub 2-0:1.0: USB hub found
2516 [ 2.582253] hub 2-0:1.0: 1 port detected
2517 [ 2.585160] ehci-platform 300c0000.usb: EHCI Host Controller
2518 [ 2.585553] ehci-platform 300c0000.usb: new USB bus registered, assigned bus number 3
2519 [ 2.585848] ehci-platform 300c0000.usb: irq 51, io mem 0x300c0000
2520 [ 2.596808] ehci-platform 300c0000.usb: USB 2.0 started, EHCI 1.00
2521 [ 2.597096] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
2522 [ 2.597115] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
2523 [ 2.597130] usb usb3: Product: EHCI Host Controller
2524 [ 2.597144] usb usb3: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
2525 [ 2.597157] usb usb3: SerialNumber: 300c0000.usb
2526 [ 2.598133] hub 3-0:1.0: USB hub found
2527 [ 2.598202] hub 3-0:1.0: 1 port detected
2528 [ 2.601121] ehci-platform 30100000.usb: EHCI Host Controller
2529 [ 2.601512] ehci-platform 30100000.usb: new USB bus registered, assigned bus number 4
2530 [ 2.601797] ehci-platform 30100000.usb: irq 53, io mem 0x30100000
2531 [ 2.612808] ehci-platform 30100000.usb: USB 2.0 started, EHCI 1.00
2532 [ 2.613102] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
2533 [ 2.613120] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
2534 [ 2.613136] usb usb4: Product: EHCI Host Controller
2535 [ 2.613149] usb usb4: Manufacturer: Linux 4.4.194-rk322x ehci_hcd
2536 [ 2.613163] usb usb4: SerialNumber: 30100000.usb
2537 [ 2.614137] hub 4-0:1.0: USB hub found
2538 [ 2.614205] hub 4-0:1.0: 1 port detected
2539 [ 2.615019] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
2540 [ 2.615093] ohci-platform: OHCI generic platform driver
2541 [ 2.615499] ohci-platform 300a0000.usb: Generic Platform OHCI controller
2542 [ 2.615895] ohci-platform 300a0000.usb: new USB bus registered, assigned bus number 5
2543 [ 2.616154] ohci-platform 300a0000.usb: irq 50, io mem 0x300a0000
2544 [ 2.673054] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
2545 [ 2.673078] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
2546 [ 2.673092] usb usb5: Product: Generic Platform OHCI controller
2547 [ 2.673106] usb usb5: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
2548 [ 2.673120] usb usb5: SerialNumber: 300a0000.usb
2549 [ 2.674144] hub 5-0:1.0: USB hub found
2550 [ 2.674212] hub 5-0:1.0: 1 port detected
2551 [ 2.675068] ohci-platform 300e0000.usb: Generic Platform OHCI controller
2552 [ 2.675453] ohci-platform 300e0000.usb: new USB bus registered, assigned bus number 6
2553 [ 2.675712] ohci-platform 300e0000.usb: irq 52, io mem 0x300e0000
2554 [ 2.733047] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
2555 [ 2.733071] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
2556 [ 2.733086] usb usb6: Product: Generic Platform OHCI controller
2557 [ 2.733100] usb usb6: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
2558 [ 2.733113] usb usb6: SerialNumber: 300e0000.usb
2559 [ 2.734095] hub 6-0:1.0: USB hub found
2560 [ 2.734171] hub 6-0:1.0: 1 port detected
2561 [ 2.734967] ohci-platform 30120000.usb: Generic Platform OHCI controller
2562 [ 2.735326] ohci-platform 30120000.usb: new USB bus registered, assigned bus number 7
2563 [ 2.735592] ohci-platform 30120000.usb: irq 54, io mem 0x30120000
2564 [ 2.793061] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
2565 [ 2.793085] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
2566 [ 2.793100] usb usb7: Product: Generic Platform OHCI controller
2567 [ 2.793114] usb usb7: Manufacturer: Linux 4.4.194-rk322x ohci_hcd
2568 [ 2.793127] usb usb7: SerialNumber: 30120000.usb
2569 [ 2.794092] hub 7-0:1.0: USB hub found
2570 [ 2.794161] hub 7-0:1.0: 1 port detected
2571 [ 2.795073] usbcore: registered new interface driver cdc_acm
2572 [ 2.795089] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
2573 [ 2.795197] usbcore: registered new interface driver cdc_wdm
2574 [ 2.795505] usbcore: registered new interface driver usb-storage
2575 [ 2.795676] usbcore: registered new interface driver usbserial
2576 [ 2.795755] usbcore: registered new interface driver usbserial_generic
2577 [ 2.795827] usbserial: USB Serial support registered for generic
2578 [ 2.795933] usbcore: registered new interface driver keyspan
2579 [ 2.795994] usbserial: USB Serial support registered for Keyspan - (without firmware)
2580 [ 2.796052] usbserial: USB Serial support registered for Keyspan 1 port adapter
2581 [ 2.796111] usbserial: USB Serial support registered for Keyspan 2 port adapter
2582 [ 2.796169] usbserial: USB Serial support registered for Keyspan 4 port adapter
2583 [ 2.796285] usbcore: registered new interface driver option
2584 [ 2.796345] usbserial: USB Serial support registered for GSM modem (1-port)
2585 [ 2.797098] usbcore: registered new interface driver oti6858
2586 [ 2.797170] usbserial: USB Serial support registered for oti6858
2587 [ 2.797275] usbcore: registered new interface driver qcserial
2588 [ 2.797351] usbserial: USB Serial support registered for Qualcomm USB modem
2589 [ 2.797514] usbcore: registered new interface driver sierra
2590 [ 2.797575] usbserial: USB Serial support registered for Sierra USB modem
2591 [ 2.799054] usbcore: registered new interface driver iforce
2592 [ 2.799220] usbcore: registered new interface driver xpad
2593 [ 2.799521] usbcore: registered new interface driver usbtouchscreen
2594 [ 2.800691] i2c /dev entries driver
2595 [ 2.802700] IR NEC protocol handler initialized
2596 [ 2.802726] IR RC5(x/sz) protocol handler initialized
2597 [ 2.802744] IR RC6 protocol handler initialized
2598 [ 2.802761] IR JVC protocol handler initialized
2599 [ 2.802778] IR Sony protocol handler initialized
2600 [ 2.802795] IR SANYO protocol handler initialized
2601 [ 2.802812] IR Sharp protocol handler initialized
2602 [ 2.802829] IR MCE Keyboard/mouse protocol handler initialized
2603 [ 2.802847] IR XMP protocol handler initialized
2604 [ 2.804548] usbcore: registered new interface driver uvcvideo
2605 [ 2.804562] USB Video Class driver (1.1.1)
2606 [ 2.806500] Boot mode: normal
2607 [ 2.807651] rockchip-thermal 11150000.tsadc: tsadc is probed successfully!
2608 [ 2.809380] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
2609 [ 2.809739] Bluetooth: Virtual HCI driver ver 1.5
2610 [ 2.810017] Bluetooth: HCI UART driver ver 2.3
2611 [ 2.810035] Bluetooth: HCI UART protocol H4 registered
2612 [ 2.810046] Bluetooth: HCI UART protocol LL registered
2613 [ 2.810057] Bluetooth: HCI UART protocol ATH3K registered
2614 [ 2.810068] Bluetooth: HCI UART protocol Three-wire (H5) registered
2615 [ 2.810245] Bluetooth: HCI UART protocol BCM registered
2616 [ 2.810397] usbcore: registered new interface driver bfusb
2617 [ 2.810542] usbcore: registered new interface driver btusb
2618 [ 2.810564] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
2619 [ 2.811144] cpu cpu0: leakage=6
2620 [ 2.811176] cpu cpu0: leakage-volt-sel=0
2621 [ 2.811382] cpu cpu0: Failed to get pvtm
2622 [ 2.812729] cpu cpu0: avs=0
2623 [ 2.812882] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
2624 [ 2.812908] cpu cpu0: failed to read out thermal zone (-22)
2625 [ 2.813537] cpu cpu0: failed to find power_model node
2626 [ 2.814170] pwrseq_simple sdio-pwrseq: GPIO lookup for consumer reset
2627 [ 2.814190] pwrseq_simple sdio-pwrseq: using device tree for GPIO lookup
2628 [ 2.814212] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0)
2629 [ 2.814559] Synopsys Designware Multimedia Card Interface Driver
2630 [ 2.815161] dwmmc_rockchip 30000000.dwmmc: IDMAC supports 32-bit address mode.
2631 [ 2.815281] dwmmc_rockchip 30000000.dwmmc: Using internal DMA controller.
2632 [ 2.815299] dwmmc_rockchip 30000000.dwmmc: Version ID is 270a
2633 [ 2.815364] dwmmc_rockchip 30000000.dwmmc: DW MMC controller at irq 45,32 bit host data width,256 deep fifo
2634 [ 2.815415] dwmmc_rockchip 30000000.dwmmc: No vmmc regulator found
2635 [ 2.815426] dwmmc_rockchip 30000000.dwmmc: No vqmmc regulator found
2636 [ 2.815447] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer cd
2637 [ 2.815457] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
2638 [ 2.815483] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/dwmmc@30000000[0]' - status (0)
2639 [ 2.815520] gpio-49 (cd): gpiod_set_debounce: missing set() or set_debounce() operations
2640 [ 2.815531] dwmmc_rockchip 30000000.dwmmc: Got CD GPIO
2641 [ 2.815543] dwmmc_rockchip 30000000.dwmmc: GPIO lookup for consumer wp
2642 [ 2.815552] dwmmc_rockchip 30000000.dwmmc: using device tree for GPIO lookup
2643 [ 2.815562] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30000000[0]'
2644 [ 2.815572] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30000000[0]'
2645 [ 2.815581] dwmmc_rockchip 30000000.dwmmc: using lookup tables for GPIO lookup
2646 [ 2.815591] dwmmc_rockchip 30000000.dwmmc: lookup for GPIO wp failed
2647 [ 2.828408] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
2648 [ 2.841349] dwmmc_rockchip 30000000.dwmmc: 1 slots initialized
2649 [ 2.841723] dwmmc_rockchip 30010000.dwmmc: num-slots property not found, assuming 1 slot is available
2650 [ 2.841808] dwmmc_rockchip 30010000.dwmmc: IDMAC supports 32-bit address mode.
2651 [ 2.841895] dwmmc_rockchip 30010000.dwmmc: Using internal DMA controller.
2652 [ 2.841912] dwmmc_rockchip 30010000.dwmmc: Version ID is 270a
2653 [ 2.841969] dwmmc_rockchip 30010000.dwmmc: DW MMC controller at irq 46,32 bit host data width,256 deep fifo
2654 [ 2.842020] dwmmc_rockchip 30010000.dwmmc: No vmmc regulator found
2655 [ 2.842030] dwmmc_rockchip 30010000.dwmmc: No vqmmc regulator found
2656 [ 2.842048] dwmmc_rockchip 30010000.dwmmc: GPIO lookup for consumer wp
2657 [ 2.842058] dwmmc_rockchip 30010000.dwmmc: using device tree for GPIO lookup
2658 [ 2.842070] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@30010000[0]'
2659 [ 2.842081] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@30010000[0]'
2660 [ 2.842090] dwmmc_rockchip 30010000.dwmmc: using lookup tables for GPIO lookup
2661 [ 2.842100] dwmmc_rockchip 30010000.dwmmc: lookup for GPIO wp failed
2662 [ 2.842168] dwmmc_rockchip 30010000.dwmmc: allocated mmc-pwrseq
2663 [ 2.854929] mmc_host mmc1: Bus speed (slot 0) = 976562Hz (slot req 400000Hz, actual 244140HZ div = 2)
2664 [ 2.867574] dwmmc_rockchip 30010000.dwmmc: 1 slots initialized
2665 [ 2.868170] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/auxiliary[0]' - status (0)
2666 [ 2.868383] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/working[0]' - status (0)
2667 [ 2.868716] ledtrig-cpu: registered to indicate activity on CPUs
2668 [ 2.868902] hidraw: raw HID events driver (C) Jiri Kosina
2669 [ 2.869375] usbcore: registered new interface driver usbhid
2670 [ 2.869389] usbhid: USB HID core driver
2671 [ 2.870090] ashmem: initialized
2672 [ 2.873455] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
2673 [ 2.873639] mmc0: new high speed SDXC card at address 59b4
2674 [ 2.874497] rknandbase v1.2 2018-05-08
2675 [ 2.874922] mmcblk0: mmc0:59b4 SD 57.8 GiB
2676 [ 2.875894] rknand 30030000.nandc: rknand_probe clk rate = 150000000
2677 [ 2.876261] No.1 FLASH ID:ec de 94 c3 a4 ca
2678 [ 2.876336] No.1 FLASH ID:ec de 94 c3 a4 ca
2679 [ 2.877084] mmcblk0: p1
2680 [ 2.879482] FlashLoadPhyInfo fail 800!!
2681 [ 2.879515] ftl_init ffffffff
2682 [ 2.879527] rk_ftl_init fail
2683 [ 2.881132] usbcore: registered new interface driver snd-usb-audio
2684 [ 2.881348] usbcore: registered new interface driver snd-ua101
2685 [ 2.881536] usbcore: registered new interface driver snd-usb-caiaq
2686 [ 2.881712] usbcore: registered new interface driver snd-usb-6fire
2687 [ 2.881894] usbcore: registered new interface driver snd-usb-hiface
2688 [ 2.882030] usbcore: registered new interface driver snd-bcd2000
2689 [ 2.882170] usbcore: registered new interface driver snd_usb_pod
2690 [ 2.882320] usbcore: registered new interface driver snd_usb_podhd
2691 [ 2.882465] usbcore: registered new interface driver snd_usb_toneport
2692 [ 2.882604] usbcore: registered new interface driver snd_usb_variax
2693 [ 2.890402] u32 classifier
2694 [ 2.890431] input device check on
2695 [ 2.890443] Actions configured
2696 [ 2.890474] Netfilter messages via NETLINK v0.30.
2697 [ 2.890521] nfnl_acct: registering with nfnetlink.
2698 [ 2.890663] nf_conntrack version 0.5.0 (15384 buckets, 61536 max)
2699 [ 2.891868] Initializing XFRM netlink socket
2700 [ 2.893552] NET: Registered protocol family 10
2701 [ 2.895406] ip6_tables: (C) 2000-2006 Netfilter Core Team
2702 [ 2.895853] sit: IPv6 over IPv4 tunneling driver
2703 [ 2.897238] NET: Registered protocol family 17
2704 [ 2.897320] NET: Registered protocol family 15
2705 [ 2.897425] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
2706 [ 2.897504] Bridge firewalling registered
2707 [ 2.897530] can: controller area network core (rev 20120528 abi 9)
2708 [ 2.897652] NET: Registered protocol family 29
2709 [ 2.897687] can: raw protocol (rev 20120528)
2710 [ 2.897712] can: broadcast manager protocol (rev 20120528 t)
2711 [ 2.897747] can: netlink gateway (rev 20130117) max_hops=1
2712 [ 2.898410] Bluetooth: RFCOMM TTY layer initialized
2713 [ 2.898454] Bluetooth: RFCOMM socket layer initialized
2714 [ 2.898503] Bluetooth: RFCOMM ver 1.11
2715 [ 2.898546] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
2716 [ 2.898575] Bluetooth: HIDP socket layer initialized
2717 [ 2.898692] 8021q: 802.1Q VLAN Support v1.8
2718 [ 2.898755] lib80211: common routines for IEEE802.11 drivers
2719 [ 2.898773] lib80211_crypt: registered algorithm 'NULL'
2720 [ 2.898802] lib80211_crypt: registered algorithm 'WEP'
2721 [ 2.898830] lib80211_crypt: registered algorithm 'CCMP'
2722 [ 2.898858] lib80211_crypt: registered algorithm 'TKIP'
2723 [ 2.898882] [WLAN_RFKILL]: Enter rfkill_wlan_init
2724 [ 2.899289] [BT_RFKILL]: Enter rfkill_rk_init
2725 [ 2.899649] Key type dns_resolver registered
2726 [ 2.900099] flash vendor_init_thread!
2727 [ 2.900127] flash vendor storage:20170308 ret = -1
2728 [ 2.900216] Error: Driver 'sc031gs' is already registered, aborting...
2729 [ 2.901511] Registering SWP/SWPB emulation handler
2730 [ 2.903071] registered taskstats version 1
2731 [ 2.903115] Loading compiled-in X.509 certificates
2732 [ 2.907601] Btrfs loaded
2733 [ 2.909098] rga2: Driver loaded successfully ver:4.01
2734 [ 2.909422] rga2: Module initialized.
2735 [ 2.909477] pvtm list NULL
2736 [ 2.910963] rk-vcodec 20030000.rkvdec: leakage=5
2737 [ 2.911007] rk-vcodec 20030000.rkvdec: leakage-volt-sel=0
2738 [ 2.911169] rk-vcodec 20030000.rkvdec: Failed to get pvtm
2739 [ 2.911754] rk-vcodec 20030000.rkvdec: avs=0
2740 [ 2.912150] rk-vcodec 20030000.rkvdec: probe device
2741 [ 2.912837] rk-vcodec 20030000.rkvdec: drm allocator with mmu enabled
2742 [ 2.914517] rk-vcodec 20030000.rkvdec: init success
2743 [ 2.915888] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/hdmi-sound[0]'
2744 [ 2.915917] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/hdmi-sound[0]'
2745 [ 2.917283] asoc-simple-card hdmi-sound: i2s-hifi <-> 100c0000.i2s0 mapping ok
2746 [ 2.919892] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]'
2747 [ 2.919923] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]'
2748 [ 2.920146] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
2749 [ 2.922378] mmc1: new high speed SDIO card at address 0001
2750 [ 2.923944] asoc-simple-card spdif-sound: dit-hifi <-> 100d0000.spdif mapping ok
2751 [ 2.926340] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/reset[0]' - status (0)
2752 [ 2.926423] gpio-121 (reset): gpiod_set_debounce: missing set() or set_debounce() operations
2753 [ 2.926808] input: gpio-keys as /devices/platform/gpio-keys/input/input1
2754 [ 2.927250] hctosys: unable to open rtc device (rtc0)
2755 [ 2.940289] ALSA device list:
2756 [ 2.940318] #0: DW-I2S-HDMI
2757 [ 2.940327] #1: SPDIF
2758 [ 2.941400] Freeing unused kernel memory: 808K
2759 [ 2.941415] This architecture does not have kernel memory protection.
2760 [ 4.071143] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
2761 [ 4.820521] systemd[1]: System time before build time, advancing clock.
2762 [ 4.845773] systemd[1]: Inserted module 'autofs4'
2763 [ 4.851274] ip_tables: (C) 2000-2006 Netfilter Core Team
2764 [ 4.860403] cgroup: cgroup2: unknown option "nsdelegate"
2765 [ 4.874979] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
2766 [ 4.876092] systemd[1]: Detected architecture arm.
2767 [ 4.887668] systemd[1]: Set hostname to <rk322x-box>.
2768 [ 5.083690] ttyS2 - failed to request DMA, use interrupt mode
2769 [ 5.220216] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
2770 [ 5.220262] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
2771 [ 5.630486] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2772 [ 5.643573] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2773 [ 5.644028] systemd[1]: Listening on initctl Compatibility Named Pipe.
2774 [ 5.645171] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2775 [ 5.645293] systemd[1]: Reached target System Time Synchronized.
2776 [ 5.645869] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2777 [ 5.649867] systemd[1]: Created slice system-getty.slice.
2778 [ 5.650536] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2779 [ 5.650644] systemd[1]: Reached target Remote File Systems.
2780 [ 5.651236] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
2781 [ 5.651366] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2782 [ 5.652224] systemd[1]: Listening on Journal Socket.
2783 [ 5.653451] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2784 [ 5.658758] systemd[1]: Mounting Kernel Debug File System...
2785 [ 5.662725] random: systemd: uninitialized urandom read (16 bytes read, 40 bits of entropy available)
2786 [ 5.668528] systemd[1]: Starting Load Kernel Modules...
2787 [ 5.669469] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
2788 [ 5.675896] systemd[1]: Starting Nameserver information manager...
2789 [ 5.677124] random: systemd: uninitialized urandom read (16 bytes read, 41 bits of entropy available)
2790 [ 5.684099] systemd[1]: Starting Set the console keyboard layout...
2791 [ 5.685249] systemd[1]: Reached target Swap.
2792 [ 5.704211] systemd[1]: Starting Restore / save the current clock...
2793 [ 5.705289] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
2794 [ 5.705939] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
2795 [ 5.707092] systemd[1]: Reached target Local Encrypted Volumes.
2796 [ 5.708160] systemd[1]: Reached target Paths.
2797 [ 5.709969] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
2798 [ 5.711731] systemd[1]: Created slice system-serial\x2dgetty.slice.
2799 [ 5.721312] systemd[1]: Starting Create list of required static device nodes for the current kernel...
2800 [ 5.723608] systemd[1]: Listening on fsck to fsckd communication Socket.
2801 [ 5.724454] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
2802 [ 5.734187] systemd[1]: Starting Remount Root and Kernel File Systems...
2803 [ 5.736380] systemd[1]: Listening on Journal Socket (/dev/log).
2804 [ 5.739020] systemd[1]: Listening on udev Control Socket.
2805 [ 5.741060] systemd[1]: Listening on udev Kernel Socket.
2806 [ 5.763431] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
2807 [ 5.765607] systemd[1]: Created slice User and Session Slice.
2808 [ 5.766469] systemd[1]: Reached target Slices.
2809 [ 5.773734] systemd[1]: Starting udev Coldplug all Devices...
2810 [ 5.775836] systemd[1]: Listening on Syslog Socket.
2811 [ 5.782906] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
2812 [ 5.792661] systemd[1]: Mounting POSIX Message Queue File System...
2813 [ 5.802261] systemd[1]: Mounted Kernel Debug File System.
2814 [ 5.808327] systemd[1]: Started Load Kernel Modules.
2815 [ 5.813318] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
2816 [ 5.838230] systemd[1]: Started Restore / save the current clock.
2817 [ 5.842571] systemd[1]: Started Create list of required static device nodes for the current kernel.
2818 [ 5.846788] systemd[1]: Started Remount Root and Kernel File Systems.
2819 [ 5.852567] systemd[1]: Mounted POSIX Message Queue File System.
2820 [ 5.862034] systemd[1]: Started Nameserver information manager.
2821 [ 5.878083] systemd[1]: Starting Load/Save Random Seed...
2822 [ 5.890071] systemd[1]: Starting Create System Users...
2823 [ 5.908210] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
2824 [ 5.920947] vendor storage:20190527 ret = -1
2825 [ 5.927178] systemd[1]: Mounting Kernel Configuration File System...
2826 [ 5.933727] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
2827 [ 5.953432] systemd[1]: Starting Apply Kernel Variables...
2828 [ 5.970359] systemd[1]: Started Load/Save Random Seed.
2829 [ 5.986815] systemd[1]: Mounted Kernel Configuration File System.
2830 [ 6.029997] systemd[1]: Started Apply Kernel Variables.
2831 [ 6.041048] systemd[1]: Started Create System Users.
2832 [ 6.054789] systemd[1]: Starting Create Static Device Nodes in /dev...
2833 [ 6.123988] systemd[1]: Started Set the console keyboard layout.
2834 [ 6.144354] systemd[1]: Started Create Static Device Nodes in /dev.
2835 [ 6.149973] systemd[1]: Reached target Local File Systems (Pre).
2836 [ 6.160736] systemd[1]: Mounting /tmp...
2837 [ 6.172405] systemd[1]: Starting udev Kernel Device Manager...
2838 [ 6.183601] systemd[1]: Mounted /tmp.
2839 [ 6.189832] systemd[1]: Reached target Local File Systems.
2840 [ 6.201172] systemd[1]: Starting Set console font and keymap...
2841 [ 6.206734] systemd[1]: Condition check resulted in Mark the need to relabel after reboot being skipped.
2842 [ 6.207113] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
2843 [ 6.213326] systemd[1]: Starting Armbian ZRAM config...
2844 [ 6.236213] systemd[1]: Started Set console font and keymap.
2845 [ 6.357992] systemd[1]: Started udev Kernel Device Manager.
2846 [ 6.381725] systemd[1]: Started udev Coldplug all Devices.
2847 [ 6.396356] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
2848 [ 6.440938] systemd[1]: Started Helper to synchronize boot up for ifupdown.
2849 [ 6.457849] systemd[1]: Starting Raise network interfaces...
2850 [ 6.547378] zram: Added device: zram0
2851 [ 6.548924] zram: Added device: zram1
2852 [ 6.550497] zram: Added device: zram2
2853 [ 6.744103] rk3228-codec 12010000.codec: GPIO lookup for consumer spk-en
2854 [ 6.744135] rk3228-codec 12010000.codec: using device tree for GPIO lookup
2855 [ 6.744152] of_get_named_gpiod_flags: can't parse 'spk-en-gpios' property of node '/codec@12010000[0]'
2856 [ 6.744187] of_get_named_gpiod_flags: parsed 'spk-en-gpio' property of node '/codec@12010000[0]' - status (0)
2857 [ 6.744255] rk3228-codec 12010000.codec: spk_depop_time use default value.
2858 [ 6.745309] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound[0]'
2859 [ 6.745348] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound[0]'
2860 [ 6.765854] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '22:00:07', on 'May 6 2021'.
2861 [ 6.766188] mali-utgard 20001000.gpu: mali_platform_device->num_resources = 13
2862 [ 6.766218] mali-utgard 20001000.gpu: resource[0].start = 0x0x20001000
2863 [ 6.766230] mali-utgard 20001000.gpu: resource[1].start = 0x0x20000000
2864 [ 6.766240] mali-utgard 20001000.gpu: resource[2].start = 0x0x20003000
2865 [ 6.766252] mali-utgard 20001000.gpu: resource[3].start = 0x0x20008000
2866 [ 6.766262] mali-utgard 20001000.gpu: resource[4].start = 0x0x20004000
2867 [ 6.766273] mali-utgard 20001000.gpu: resource[5].start = 0x0x2000a000
2868 [ 6.766284] mali-utgard 20001000.gpu: resource[6].start = 0x0x20005000
2869 [ 6.766295] mali-utgard 20001000.gpu: resource[7].start = 0x0x00000020
2870 [ 6.766304] mali-utgard 20001000.gpu: resource[8].start = 0x0x00000021
2871 [ 6.766315] mali-utgard 20001000.gpu: resource[9].start = 0x0x00000022
2872 [ 6.766326] mali-utgard 20001000.gpu: resource[10].start = 0x0x00000021
2873 [ 6.766398] mali-utgard 20001000.gpu: resource[11].start = 0x0x00000022
2874 [ 6.766410] mali-utgard 20001000.gpu: resource[12].start = 0x0x00000021
2875 [ 6.766423] D : [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 623; [Func] : mali_platform_device_init(); to add platform_specific_data to platform_device_of_mali.
2876 [ 6.766835] mali-utgard 20001000.gpu: leakage=5
2877 [ 6.766876] mali-utgard 20001000.gpu: leakage-volt-sel=0
2878 [ 6.767000] mali-utgard 20001000.gpu: Failed to get pvtm
2879 [ 6.767586] mali-utgard 20001000.gpu: avs=0
2880 [ 6.768017] mali-utgard 20001000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0
2881 [ 6.784685] Mali: Mali device driver loaded
2882 [ 6.788072] systemd[1]: Found device /dev/ttyS2.
2883 [ 6.818379] asoc-simple-card sound: rk3228-hifi <-> 100b0000.i2s1 mapping ok
2884 [ 6.864981] devfreq 20001000.gpu: Couldn't update frequency transition information.
2885 [ 6.875521] zram0: detected capacity change from 0 to 504537088
2886 [ 6.893686] generic_wifi_init_module
2887 [ 6.960636] gpio_ir_recv ir-receiver: GPIO lookup for consumer (null)
2888 [ 6.960668] gpio_ir_recv ir-receiver: using device tree for GPIO lookup
2889 [ 6.960713] of_get_named_gpiod_flags: parsed 'gpios' property of node '/ir-receiver[0]' - status (0)
2890 [ 6.961006] Registered IR keymap rc-rktvbox
2891 [ 6.961276] rc rc1: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1
2892 [ 6.961786] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1/input2
2893 [ 7.173027]
2894 *** sta_cfg_set, (null) ***
2895
2896 [ 7.173075] redirect to /lib/firmware/ssv6051-wifi.cfg
2897 [ 7.181393] ssv6xxx_sdio_init
2898 [ 7.183442] =======================================
2899 [ 7.183482] == RUN SDIO ==
2900 [ 7.183507] =======================================
2901 [ 7.183536] ssv6xxx_set_sdio_clk:set sdio clk 25000000Hz
2902 [ 7.183637] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
2903 [ 7.239355] SSV6XXX_SDIO mmc1:0001:1: vendor = 0x3030 device = 0x3030
2904 [ 7.274694] ssv6xxx_sdio_power_on
2905 [ 7.301205] SSV6XXX_SDIO mmc1:0001:1: dataIOPort 0x10000 regIOPort 0x10020
2906 [ 7.301783] ssv6xxx_dev_probe(): ssv6200 device found !
2907 [ 7.311890] ssv6xxx_sdio_irq_disable
2908 [ 7.312321] Read open File fail[/data/wifimac]!!!!
2909 [ 7.312391] Write open File fail!!!![/data/wifimac]
2910 [ 7.312404] MAC address from Software MAC mode[2]
2911 [ 7.312413] EFUSE configuration
2912 [ 7.312421] Read efuse chip identity[00000000]
2913 [ 7.312429] r_calbration_result- 0
2914 [ 7.312437] sar_result- 0
2915 [ 7.312445] crystal_frequency_offset- 0
2916 [ 7.312452] tx_power_index_1- 0
2917 [ 7.312459] tx_power_index_2- 0
2918 [ 7.312469] MAC address - 00:00:00:00:00:00
2919 [ 7.321278] Registering Vendor80211
2920 [ 7.321321] Register SSV cfg80211 vendor cmd(0x67) interface
2921 [ 7.321625] [MT-ENCRYPT]: create kthread ecd80000 for CPU 0, ret = 0
2922 [ 7.321849] SSV WLAN driver ssv6200: Crypto task 451 running with priority 120.
2923 [ 7.321949] [MT-ENCRYPT]: create kthread ecd807c0 for CPU 1, ret = 0
2924 [ 7.323446] [MT-ENCRYPT]: create kthread ecd80f80 for CPU 2, ret = 0
2925 [ 7.323700] [MT-ENCRYPT]: create kthread ecd81740 for CPU 3, ret = 0
2926 [ 7.323964] SSV6XXX TX Task started.
2927 [ 7.324037] Pre-load cipher
2928 [ 7.324153] flash_file /tmp/flash.bin not found, disable sar
2929 [ 7.324171] SSV6051Q setting
2930 [ 7.324183] SSV6XXX_IQK_CFG_XTAL_24M
2931 [ 7.324194] SSV6051Q setting [0x5B606C72]
2932 [ 7.324202] TX power setting 0x5b606c72
2933 [ 7.324209] Volt regulator LDO
2934 [ 7.325035] SSV WLAN driver ssv6200: Crypto task 454 running with priority 120.
2935 [ 7.326159] reset PLL
2936 [ 7.327638] SSV WLAN driver ssv6200: Crypto task 456 running with priority 120.
2937 [ 7.332910] SSV WLAN driver ssv6200: Crypto task 452 running with priority 120.
2938 [ 7.336533] SSV6XXX RX Task started.
2939 [ 7.342562] @@@@@@@@@@@@
2940 [ 7.342589] SDIO issue -- please check 0xCE01008C 00000000!!
2941 [ 7.342600] It shouble be 0xEAAAAAAA!!
2942 [ 7.342607] @@@@@@@@@@@@
2943 [ 7.372070] calibation fail:[1]
2944 [ 7.399362] calibation fail:[2]
2945 [ 7.424234] calibation fail:[3]
2946 [ 7.434415] systemd[1]: Started Raise network interfaces.
2947 [ 7.448020] calibation fail:[4]
2948 [ 7.471499] calibation fail:[5]
2949 [ 7.496995] calibation fail:[6]
2950 [ 7.522221] calibation fail:[7]
2951 [ 7.548498] calibation fail:[8]
2952 [ 7.569835] systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
2953 [ 7.572199] calibation fail:[9]
2954 [ 7.575265] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
2955 [ 7.575619] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
2956 [ 7.575791] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
2957 [ 7.575893] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
2958 [ 7.576086] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
2959 [ 7.576198] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
2960 [ 7.576732] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
2961 [ 7.577126] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
2962 [ 7.594425] calibation fail:[10]
2963 [ 7.616389] calibation fail:[11]
2964 [ 7.638369] calibation fail:[12]
2965 [ 7.660302] calibation fail:[13]
2966 [ 7.682244] calibation fail:[14]
2967 [ 7.704171] calibation fail:[15]
2968 [ 7.726146] calibation fail:[16]
2969 [ 7.748066] calibation fail:[17]
2970 [ 7.769992] calibation fail:[18]
2971 [ 7.792546] calibation fail:[19]
2972 [ 7.815394] calibation fail:[20]
2973 [ 7.837530] calibation fail:[21]
2974 [ 7.859444] cfg80211: World regulatory domain updated:
2975 [ 7.859468] cfg80211: DFS Master region: unset
2976 [ 7.859476] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
2977 [ 7.859488] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
2978 [ 7.859500] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
2979 [ 7.859509] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
2980 [ 7.859520] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
2981 [ 7.859530] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
2982 [ 7.859540] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
2983 [ 7.859549] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
2984 [ 7.859559] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
2985 [ 7.859874] calibation fail:[22]
2986 [ 7.882030] calibation fail:[23]
2987 [ 7.904012] calibation fail:[24]
2988 [ 7.927441] calibation fail:[25]
2989 [ 7.933025] Adding 492708k swap on /dev/zram0. Priority:5 extents:1 across:492708k SS
2990 [ 7.952077] calibation fail:[26]
2991 [ 7.976481] calibation fail:[27]
2992 [ 7.999422] calibation fail:[28]
2993 [ 7.999744] random: nonblocking pool is initialized
2994 [ 8.023032] calibation fail:[29]
2995 [ 8.046502] calibation fail:[30]
2996 [ 8.070022] calibation fail:[31]
2997 [ 8.093541] calibation fail:[32]
2998 [ 8.116945] calibation fail:[33]
2999 [ 8.124087] zram1: detected capacity change from 0 to 52428800
3000 [ 8.139905] calibation fail:[34]
3001 [ 8.163117] calibation fail:[35]
3002 [ 8.186577] calibation fail:[36]
3003 [ 8.193169] systemd[1]: Started Armbian ZRAM config.
3004 [ 8.203367] systemd[1]: Starting Armbian memory supported logging...
3005 [ 8.210324] calibation fail:[37]
3006 [ 8.234175] calibation fail:[38]
3007 [ 8.258050] calibation fail:[39]
3008 [ 8.282077] calibation fail:[40]
3009 [ 8.304081] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
3010 [ 8.306197] calibation fail:[41]
3011 [ 8.331237] calibation fail:[42]
3012 [ 8.354738] calibation fail:[43]
3013 [ 8.379478] calibation fail:[44]
3014 [ 8.404364] calibation fail:[45]
3015 [ 8.429018] calibation fail:[46]
3016 [ 8.453027] calibation fail:[47]
3017 [ 8.477046] calibation fail:[48]
3018 [ 8.501016] calibation fail:[49]
3019 [ 8.525037] calibation fail:[50]
3020 [ 8.549027] calibation fail:[51]
3021 [ 8.573009] calibation fail:[52]
3022 [ 8.596649] calibation fail:[53]
3023 [ 8.621507] calibation fail:[54]
3024 [ 8.646447] calibation fail:[55]
3025 [ 8.671267] calibation fail:[56]
3026 [ 8.695259] calibation fail:[57]
3027 [ 8.719706] calibation fail:[58]
3028 [ 8.744073] calibation fail:[59]
3029 [ 8.768323] calibation fail:[60]
3030 [ 8.791360] calibation fail:[61]
3031 [ 8.814241] calibation fail:[62]
3032 [ 8.837387] calibation fail:[63]
3033 [ 8.860588] calibation fail:[64]
3034 [ 8.883569] calibation fail:[65]
3035 [ 8.905924] calibation fail:[66]
3036 [ 8.928287] calibation fail:[67]
3037 [ 8.950851] calibation fail:[68]
3038 [ 8.973274] calibation fail:[69]
3039 [ 8.995692] calibation fail:[70]
3040 [ 9.018129] calibation fail:[71]
3041 [ 9.040516] calibation fail:[72]
3042 [ 9.062958] calibation fail:[73]
3043 [ 9.085386] calibation fail:[74]
3044 [ 9.107775] calibation fail:[75]
3045 [ 9.130226] calibation fail:[76]
3046 [ 9.152635] calibation fail:[77]
3047 [ 9.175095] calibation fail:[78]
3048 [ 9.197482] calibation fail:[79]
3049 [ 9.219864] calibation fail:[80]
3050 [ 9.242287] calibation fail:[81]
3051 [ 9.264676] calibation fail:[82]
3052 [ 9.287096] calibation fail:[83]
3053 [ 9.309521] calibation fail:[84]
3054 [ 9.331939] calibation fail:[85]
3055 [ 9.354328] calibation fail:[86]
3056 [ 9.376732] calibation fail:[87]
3057 [ 9.399221] calibation fail:[88]
3058 [ 9.421594] calibation fail:[89]
3059 [ 9.444025] calibation fail:[90]
3060 [ 9.466435] calibation fail:[91]
3061 [ 9.488859] calibation fail:[92]
3062 [ 9.511270] calibation fail:[93]
3063 [ 9.533657] calibation fail:[94]
3064 [ 9.556093] calibation fail:[95]
3065 [ 9.578544] calibation fail:[96]
3066 [ 9.600910] calibation fail:[97]
3067 [ 9.623356] calibation fail:[98]
3068 [ 9.645758] calibation fail:[99]
3069 [ 9.668122] calibation fail:[100]
3070 [ 9.669771] ieee80211 phy0: Selected rate control algorithm 'ssv6xxx_rate_control'
3071 [ 9.671321] ieee80211 phy0: SSV6200 of South Silicon Valley
3072 [ 9.675507] systemd[1]: Starting Load/Save RF Kill Switch Status...
3073 [ 10.200341] systemd[1]: Started Load/Save RF Kill Switch Status.
3074 [ 11.826590] systemd[1]: Started Armbian memory supported logging.
3075 [ 11.838053] systemd[1]: Starting Journal Service...
3076 [ 12.265003] systemd[1]: Started Journal Service.
3077 [ 12.336318] systemd-journald[592]: Received request to flush runtime journal from PID 1
3078
3079 ### armbian-release:
3080
3081 # PLEASE DO NOT EDIT THIS FILE
3082 BOARD=rk322x-box
3083 BOARD_NAME="rk322x-box"
3084 BOARDFAMILY=rk322x
3085 BUILD_REPOSITORY_URL=git@github.com:armbian/build.git
3086 BUILD_REPOSITORY_COMMIT=08297378c-dirty
3087 DISTRIBUTION_CODENAME=buster
3088 DISTRIBUTION_STATUS=supported
3089 VERSION=21.05.1
3090 LINUXFAMILY=rk322x
3091 ARCH=arm
3092 IMAGE_TYPE=stable
3093 BOARD_TYPE=tvb
3094 INITRD_ARCH=arm
3095 KERNEL_IMAGE_TYPE=Image
3096
3097 ### boot environment:
3098
3099 verbosity=1
3100 extraargs=coherent_pool=2M
3101 bootlogo=false
3102 overlay_prefix=rk322x
3103 fdtfile=rk322x-box.dtb
3104 rootdev=UUID=2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
3105 rootfstype=ext4
3106 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u
3107 overlays=nand led-conf2
3108
3109 ### lsusb:
3110
3111 Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3112 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3113 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3114 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3115 Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3116 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3117 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3118
3119 ### lscpu:
3120
3121 Architecture: armv7l
3122 Byte Order: Little Endian
3123 CPU(s): 4
3124 On-line CPU(s) list: 0-3
3125 Thread(s) per core: 1
3126 Core(s) per socket: 4
3127 Socket(s): 1
3128 Vendor ID: ARM
3129 Model: 5
3130 Model name: Cortex-A7
3131 Stepping: r0p5
3132 CPU max MHz: 1200.0000
3133 CPU min MHz: 408.0000
3134 BogoMIPS: 70.58
3135 Flags: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
3136
3137 ### cpuinfo:
3138
3139 processor : 0
3140 model name : ARMv7 Processor rev 5 (v7l)
3141 BogoMIPS : 70.58
3142 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
3143 CPU implementer : 0x41
3144 CPU architecture: 7
3145 CPU variant : 0x0
3146 CPU part : 0xc07
3147 CPU revision : 5
3148
3149 processor : 1
3150 model name : ARMv7 Processor rev 5 (v7l)
3151 BogoMIPS : 70.58
3152 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
3153 CPU implementer : 0x41
3154 CPU architecture: 7
3155 CPU variant : 0x0
3156 CPU part : 0xc07
3157 CPU revision : 5
3158
3159 processor : 2
3160 model name : ARMv7 Processor rev 5 (v7l)
3161 BogoMIPS : 70.58
3162 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
3163 CPU implementer : 0x41
3164 CPU architecture: 7
3165 CPU variant : 0x0
3166 CPU part : 0xc07
3167 CPU revision : 5
3168
3169 processor : 3
3170 model name : ARMv7 Processor rev 5 (v7l)
3171 BogoMIPS : 70.58
3172 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
3173 CPU implementer : 0x41
3174 CPU architecture: 7
3175 CPU variant : 0x0
3176 CPU part : 0xc07
3177 CPU revision : 5
3178
3179 Hardware : Generic DT based system
3180 Revision : 0000
3181 Serial : cd1d5ffa03aecfa2
3182
3183 ### meminfo:
3184
3185 MemTotal: 985420 kB
3186 MemFree: 900356 kB
3187 MemAvailable: 927648 kB
3188 Buffers: 8744 kB
3189 Cached: 30396 kB
3190 SwapCached: 0 kB
3191 Active: 28892 kB
3192 Inactive: 18748 kB
3193 Active(anon): 8632 kB
3194 Inactive(anon): 5732 kB
3195 Active(file): 20260 kB
3196 Inactive(file): 13016 kB
3197 Unevictable: 0 kB
3198 Mlocked: 0 kB
3199 HighTotal: 0 kB
3200 HighFree: 0 kB
3201 LowTotal: 985420 kB
3202 LowFree: 900356 kB
3203 SwapTotal: 492708 kB
3204 SwapFree: 492708 kB
3205 Dirty: 1704 kB
3206 Writeback: 0 kB
3207 AnonPages: 8568 kB
3208 Mapped: 10620 kB
3209 Shmem: 5868 kB
3210 Slab: 18884 kB
3211 SReclaimable: 10120 kB
3212 SUnreclaim: 8764 kB
3213 KernelStack: 1128 kB
3214 PageTables: 696 kB
3215 NFS_Unstable: 0 kB
3216 Bounce: 0 kB
3217 WritebackTmp: 0 kB
3218 CommitLimit: 985416 kB
3219 Committed_AS: 31508 kB
3220 VmallocTotal: 245760 kB
3221 VmallocUsed: 0 kB
3222 VmallocChunk: 0 kB
3223 CmaTotal: 16384 kB
3224 CmaFree: 12208 kB
3225
3226 ### virtual memory:
3227
3228 vm.admin_reserve_kbytes = 8192
3229 vm.block_dump = 0
3230 vm.dirty_background_bytes = 0
3231 vm.dirty_background_ratio = 10
3232 vm.dirty_bytes = 0
3233 vm.dirty_expire_centisecs = 3000
3234 vm.dirty_ratio = 20
3235 vm.dirtytime_expire_seconds = 43200
3236 vm.dirty_writeback_centisecs = 500
3237 vm.drop_caches = 0
3238 vm.extra_free_kbytes = 0
3239 vm.highmem_is_dirtyable = 0
3240 vm.laptop_mode = 0
3241 vm.legacy_va_layout = 0
3242 vm.lowmem_reserve_ratio = 32 32
3243 vm.max_map_count = 65530
3244 vm.min_free_kbytes = 3924
3245 vm.mmap_min_addr = 32768
3246 vm.mmap_rnd_bits = 8
3247 vm.nr_pdflush_threads = 0
3248 vm.oom_dump_tasks = 1
3249 vm.oom_kill_allocating_task = 0
3250 vm.overcommit_kbytes = 0
3251 vm.overcommit_memory = 0
3252 vm.overcommit_ratio = 50
3253 vm.page-cluster = 0
3254 vm.panic_on_oom = 0
3255 vm.percpu_pagelist_fraction = 0
3256 vm.stat_interval = 1
3257 vm.swappiness = 100
3258 vm.user_reserve_kbytes = 30419
3259 vm.vfs_cache_pressure = 100
3260
3261 ### ip addr:
3262
3263 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
3264 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
3265 inet XXX.XXX.0.1/8 scope host lo
3266 valid_lft forever preferred_lft forever
3267 inet6 ::1/128 scope host
3268 valid_lft forever preferred_lft forever
3269 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
3270 link/ether e2:c8:cc:5f:46:26 brd ff:ff:ff:ff:ff:ff
3271 3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
3272 link/ether f6:b4:e0:5a:1e:3a brd ff:ff:ff:ff:ff:ff
3273 4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1
3274 link/sit XXX.XXX.0.0 brd XXX.XXX.0.0
3275 5: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
3276 link/ether 70:73:72:f7:f1:cf brd ff:ff:ff:ff:ff:ff
3277
3278 ### partitions:
3279
3280 major minor #blocks name
3281
3282 179 0 60620800 mmcblk0
3283 179 1 60010496 mmcblk0p1
3284 253 0 492712 zram0
3285 253 1 51200 zram1
3286
3287 ### df:
3288
3289 udev 471M 0 471M 0% /dev
3290 tmpfs 97M 2.8M 94M 3% /run
3291 /dev/mmcblk0p1 56G 1.1G 55G 2% /
3292 tmpfs 482M 0 482M 0% /dev/shm
3293 tmpfs 5.0M 4.0K 5.0M 1% /run/lock
3294 tmpfs 482M 0 482M 0% /sys/fs/cgroup
3295 tmpfs 482M 0 482M 0% /tmp
3296 /dev/zram1 49M 1.7M 44M 4% /var/log
3297
3298 ### lsblk:
3299
3300 NAME FSTYPE SIZE MOUNTPOINT UUID
3301 mmcblk0 57.8G
3302 └─mmcblk0p1 ext4 57.2G / 2ca5ad18-5d1f-4279-8d1e-6c805b6be8db
3303 zram1 50M /var/log
3304
3305 ### zramctl:
3306
3307 NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT
3308 /dev/zram1 lz4 50M 132K 867B 32K 4 /var/log
3309 /dev/zram0 lzo 481.2M 4K 76B 4K 4 [SWAP]
3310
3311 ### mtab:
3312
3313 /dev/mmcblk0p1 / ext4 rw,noatime,errors=remount-ro,commit=600 0 0
3314 /dev/mmcblk0p1 /var/log.hdd ext4 rw,noatime,errors=remount-ro,commit=600 0 0
3315 /dev/zram1 /var/log ext4 rw,relatime,discard 0 0
3316
3317 ### mmc0:59b4 info:
3318
3319 cid: 1d41445344202020100000002c015287
3320 csd: 400e00325b590001ce7f7f800a4000cf
3321 scr: 0245804300000000
3322 date: 02/2021
3323 name: SD
3324 type: SD
3325 preferred_erase_size: 4194304
3326 fwrev: 0x0
3327 hwrev: 0x1
3328 oemid: 0x4144
3329 manfid: 0x00001d
3330 serial: 0x0000002c
3331 uevent: DRIVER=mmcblk MMC_TYPE=SD MMC_NAME=SD MODALIAS=mmc:block
3332 erase_size: 512
3333
3334 ### Boot system health:
3335
3336 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St.
3337 22:37:08: 1200MHz 1.44 48% 29% 16% 0% 2% 0% 61.0°C 0/4
3338 22:37:08: 1200MHz 1.80 58% 25% 31% 1% 0% 0% 60.0°C 0/4
3339 22:37:08: 816MHz 1.80 34% 20% 12% 1% 0% 0% 58.0°C 0/4
3340 22:37:09: 816MHz 1.80 33% 20% 11% 1% 0% 0% 57.0°C 0/4
3341 22:37:09: 816MHz 1.80 35% 19% 15% 1% 0% 0% 58.0°C 0/4
3342
3343 ### lsusb:
3344
3345 Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3346 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3347 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3348 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3349 Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3350 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3351 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3352
3353 /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
3354 /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
3355 /: Bus 05.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
3356 /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
3357 /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
3358 /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
3359 /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
3360
3361 ### Installed packages:
3362
3363 ii armbian-bsp-cli-rk322x-box 21.05.1 armhf Tweaks for Armbian buster on rk322x-box
3364 ii armbian-config 21.05.1 all Armbian configuration utility
3365 ii armbian-firmware 21.05.1 all Linux firmware
3366 ii armbian-zsh 21.05.1 all Armbian improved ZShell
3367 ii hostapd 3:2.9-102~armbian20.05.2+1 armhf IEEE 802.11 AP and IEEE 802.1X/WPA/WPA2/EAP Authenticator
3368 ii htop 3.1.0-0~armbian20.08.2+1 armhf interactive processes viewer
3369 ii linux-base 4.6 all Linux image base package
3370 ii linux-dtb-legacy-rk322x 21.05.1 armhf Linux DTB, version 4.4.194-rk322x
3371 ii linux-image-legacy-rk322x 21.05.1 armhf Linux kernel, version 4.4.194-rk322x
3372 ii linux-libc-dev:armhf 4.19.181-1 armhf Linux support headers for userspace development
3373 ii linux-u-boot-rk322x-box-legacy 21.05.1 armhf Uboot loader 2021.04
3374
3375 ### Loaded modules:
3376
3377 Module Size Used by
3378 lz4 16384 4
3379 lz4_compress 16384 1 lz4
3380 gpio_ir_recv 16384 0
3381 ssv6051 212992 0
3382 lzo 16384 4
3383 mali 229376 0
3384 snd_soc_rk3228 16384 1
3385 zram 24576 2
3386 ip_tables 24576 0
3387 autofs4 32768 0
3388
3389 ### nand-sata-install.log:
3390
3391 Thu 03 Jun 2021 10:36:28 PM UTC: Start nand-sata-install.
3392
3393 ### Current system health:
3394
3395 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St.
3396 22:57:07: 1200MHz 4.09 14% 2% 11% 0% 0% 0% 57.0°C 0/4
3397 22:57:07: 1200MHz 4.09 6% 5% 0% 1% 0% 0% 57.0°C 0/4
3398 22:57:07: 1200MHz 4.09 6% 4% 0% 1% 0% 0% 57.0°C 0/4
3399 22:57:08: 1200MHz 4.09 7% 5% 0% 2% 0% 0% 56.0°C 0/4
3400 22:57:08: 1200MHz 4.09 6% 5% 0% 1% 0% 0% 56.0°C 0/4
3401 22:57:11: 1200MHz 4.09 14% 2% 11% 0% 0% 0% 64.0°C 0/4
3402 22:57:12: 1200MHz 4.48 87% 0% 87% 0% 0% 0% 60.0°C 0/4
3403 22:57:12: 1200MHz 4.48 6% 5% 0% 1% 0% 0% 59.0°C 0/4
3404 22:57:13: 1200MHz 4.48 6% 5% 0% 0% 0% 0% 58.0°C 0/4
3405 22:57:13: 1200MHz 4.48 6% 5% 0% 1% 0% 0% 58.0°C 0/4
3406
3407 ### resolv.conf
3408
3409 -rw-r--r-- 1 root root 74 Jun 3 22:37 /etc/resolv.conf
3410 # Generated by NetworkManager
3411 nameserver XXX.XXX.9.196
3412 nameserver XXX.XXX.9.164
3413
3414 ### Current sysinfo:
3415
3416 Linux 4.4.194-rk322x (rk322x-box) 06/03/2021 _armv7l_ (4 CPU)
3417
3418 avg-cpu: %user %nice %system %iowait %steal %idle
3419 11.40 0.01 2.22 0.71 0.00 85.66
3420
3421 Device tps kB_read/s kB_wrtn/s kB_read kB_wrtn
3422 ram0 0.00 0.00 0.00 0 0
3423 mmcblk0 10.55 138.04 243.77 165753 292712
3424 mmcblk0p1 10.42 135.43 243.77 162617 292712
3425 zram0 0.47 1.89 0.00 2264 4
3426 zram1 0.62 0.37 2.11 444 2532
3427 zram2 0.00 0.00 0.00 0 0
3428
3429 procs -----------------------memory---------------------- ---swap-- -----io---- -system-- --------cpu--------
3430 r b swpd free buff cache si so bi bo in cs us sy id wa st
3431 0 0 0 596672 33188 293000 0 0 35 62 280 286 11 2 86 1 0
3432
3433 total used free shared buff/cache available
3434 Mem: 962Mi 61Mi 582Mi 7.0Mi 318Mi 878Mi
3435 Swap: 481Mi 0B 481Mi
3436
3437 NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT
3438 /dev/zram1 lz4 50M 2.1M 574.4K 932K 4 /var/log
3439 /dev/zram0 lzo 481.2M 4K 76B 4K 4 [SWAP]
3440
3441 22:57:14 up 20 min, 1 user, load average: 4.48, 4.53, 3.43
3442
3443 [ 8.163117] calibation fail:[35]
3444 [ 8.186577] calibation fail:[36]
3445 [ 8.193169] systemd[1]: Started Armbian ZRAM config.
3446 [ 8.203367] systemd[1]: Starting Armbian memory supported logging...
3447 [ 8.210324] calibation fail:[37]
3448 [ 8.234175] calibation fail:[38]
3449 [ 8.258050] calibation fail:[39]
3450 [ 8.282077] calibation fail:[40]
3451 [ 8.304081] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
3452 [ 8.306197] calibation fail:[41]
3453 [ 8.331237] calibation fail:[42]
3454 [ 8.354738] calibation fail:[43]
3455 [ 8.379478] calibation fail:[44]
3456 [ 8.404364] calibation fail:[45]
3457 [ 8.429018] calibation fail:[46]
3458 [ 8.453027] calibation fail:[47]
3459 [ 8.477046] calibation fail:[48]
3460 [ 8.501016] calibation fail:[49]
3461 [ 8.525037] calibation fail:[50]
3462 [ 8.549027] calibation fail:[51]
3463 [ 8.573009] calibation fail:[52]
3464 [ 8.596649] calibation fail:[53]
3465 [ 8.621507] calibation fail:[54]
3466 [ 8.646447] calibation fail:[55]
3467 [ 8.671267] calibation fail:[56]
3468 [ 8.695259] calibation fail:[57]
3469 [ 8.719706] calibation fail:[58]
3470 [ 8.744073] calibation fail:[59]
3471 [ 8.768323] calibation fail:[60]
3472 [ 8.791360] calibation fail:[61]
3473 [ 8.814241] calibation fail:[62]
3474 [ 8.837387] calibation fail:[63]
3475 [ 8.860588] calibation fail:[64]
3476 [ 8.883569] calibation fail:[65]
3477 [ 8.905924] calibation fail:[66]
3478 [ 8.928287] calibation fail:[67]
3479 [ 8.950851] calibation fail:[68]
3480 [ 8.973274] calibation fail:[69]
3481 [ 8.995692] calibation fail:[70]
3482 [ 9.018129] calibation fail:[71]
3483 [ 9.040516] calibation fail:[72]
3484 [ 9.062958] calibation fail:[73]
3485 [ 9.085386] calibation fail:[74]
3486 [ 9.107775] calibation fail:[75]
3487 [ 9.130226] calibation fail:[76]
3488 [ 9.152635] calibation fail:[77]
3489 [ 9.175095] calibation fail:[78]
3490 [ 9.197482] calibation fail:[79]
3491 [ 9.219864] calibation fail:[80]
3492 [ 9.242287] calibation fail:[81]
3493 [ 9.264676] calibation fail:[82]
3494 [ 9.287096] calibation fail:[83]
3495 [ 9.309521] calibation fail:[84]
3496 [ 9.331939] calibation fail:[85]
3497 [ 9.354328] calibation fail:[86]
3498 [ 9.376732] calibation fail:[87]
3499 [ 9.399221] calibation fail:[88]
3500 [ 9.421594] calibation fail:[89]
3501 [ 9.444025] calibation fail:[90]
3502 [ 9.466435] calibation fail:[91]
3503 [ 9.488859] calibation fail:[92]
3504 [ 9.511270] calibation fail:[93]
3505 [ 9.533657] calibation fail:[94]
3506 [ 9.556093] calibation fail:[95]
3507 [ 9.578544] calibation fail:[96]
3508 [ 9.600910] calibation fail:[97]
3509 [ 9.623356] calibation fail:[98]
3510 [ 9.645758] calibation fail:[99]
3511 [ 9.668122] calibation fail:[100]
3512 [ 9.669771] ieee80211 phy0: Selected rate control algorithm 'ssv6xxx_rate_control'
3513 [ 9.671321] ieee80211 phy0: SSV6200 of South Silicon Valley
3514 [ 9.675507] systemd[1]: Starting Load/Save RF Kill Switch Status...
3515 [ 10.200341] systemd[1]: Started Load/Save RF Kill Switch Status.
3516 [ 11.826590] systemd[1]: Started Armbian memory supported logging.
3517 [ 11.838053] systemd[1]: Starting Journal Service...
3518 [ 12.265003] systemd[1]: Started Journal Service.
3519 [ 12.336318] systemd-journald[592]: Received request to flush runtime journal from PID 1
3520 [ 13.400283] nr_pdflush_threads exported in /proc is scheduled for removal
3521 [ 23.703735] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
3522 [ 23.830223] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
3523 [ 23.830642] SVN version 16529
3524 [ 23.830662] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3525 [ 23.830671] COMPILER HOST icomm-buildserver-T320
3526 [ 23.830678] COMPILER DATE 12-08-2017-10:34:54
3527 [ 23.830685] COMPILER OS linux
3528 [ 23.830692] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3529 [ 23.830852] CHIP TAG: 0
3530 [ 23.831190] CHIP ID: SSV6006C0
3531 [ 23.833749] 0x800e0000
3532 [ 23.858257] ERROR!!Please check interface!
3533 [ 23.858283] [0xca000200]: 0x0c000000!=0x00000000
3534 [ 23.858290] SOS!SOS!
3535 [ 23.858296] Initialize ssv6200 mac fail!!
3536 [ 24.020558] SVN version 16529
3537 [ 24.020598] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3538 [ 24.020621] COMPILER HOST icomm-buildserver-T320
3539 [ 24.020638] COMPILER DATE 12-08-2017-10:34:54
3540 [ 24.020653] COMPILER OS linux
3541 [ 24.020662] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3542 [ 24.032908] CHIP TAG: 0
3543 [ 24.035074] CHIP ID: SSV6006C0
3544 [ 24.046396] 0x800e0000
3545 [ 24.089463] ERROR!!Please check interface!
3546 [ 24.089491] [0xca000200]: 0x0c000000!=0x00000000
3547 [ 24.089498] SOS!SOS!
3548 [ 24.089505] Initialize ssv6200 mac fail!!
3549 [ 24.094865] SVN version 16529
3550 [ 24.094889] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3551 [ 24.094898] COMPILER HOST icomm-buildserver-T320
3552 [ 24.094905] COMPILER DATE 12-08-2017-10:34:54
3553 [ 24.094912] COMPILER OS linux
3554 [ 24.094918] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3555 [ 24.095663] CHIP TAG: 0
3556 [ 24.101513] CHIP ID: SSV6006C0
3557 [ 24.106158] 0x800e0000
3558 [ 24.142696] ERROR!!Please check interface!
3559 [ 24.142722] [0xca000200]: 0x0c000000!=0x00000000
3560 [ 24.142729] SOS!SOS!
3561 [ 24.142736] Initialize ssv6200 mac fail!!
3562 [ 25.765283] rk_gmac-dwmac 30200000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
3563 [ 34.049409] SVN version 16529
3564 [ 34.049434] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3565 [ 34.049443] COMPILER HOST icomm-buildserver-T320
3566 [ 34.049450] COMPILER DATE 12-08-2017-10:34:54
3567 [ 34.049456] COMPILER OS linux
3568 [ 34.049463] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3569 [ 34.049726] CHIP TAG: 0
3570 [ 34.049997] CHIP ID: SSV6006C0
3571 [ 34.053238] 0x800e0000
3572 [ 34.095744] ERROR!!Please check interface!
3573 [ 34.095770] [0xca000200]: 0x0c000000!=0x00000000
3574 [ 34.095777] SOS!SOS!
3575 [ 34.095784] Initialize ssv6200 mac fail!!
3576 [ 34.098424] SVN version 16529
3577 [ 34.098448] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3578 [ 34.098460] COMPILER HOST icomm-buildserver-T320
3579 [ 34.098473] COMPILER DATE 12-08-2017-10:34:54
3580 [ 34.098480] COMPILER OS linux
3581 [ 34.098487] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3582 [ 34.098723] CHIP TAG: 0
3583 [ 34.098998] CHIP ID: SSV6006C0
3584 [ 34.102525] 0x800e0000
3585 [ 34.144416] ERROR!!Please check interface!
3586 [ 34.144442] [0xca000200]: 0x0c000000!=0x00000000
3587 [ 34.144449] SOS!SOS!
3588 [ 34.144456] Initialize ssv6200 mac fail!!
3589 [ 44.051925] SVN version 16529
3590 [ 44.051960] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3591 [ 44.051974] COMPILER HOST icomm-buildserver-T320
3592 [ 44.051988] COMPILER DATE 12-08-2017-10:34:54
3593 [ 44.052000] COMPILER OS linux
3594 [ 44.052013] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3595 [ 44.052343] CHIP TAG: 0
3596 [ 44.052736] CHIP ID: SSV6006C0
3597 [ 44.057460] 0x800e0000
3598 [ 44.122949] ERROR!!Please check interface!
3599 [ 44.122982] [0xca000200]: 0x0c000000!=0x00000000
3600 [ 44.122996] SOS!SOS!
3601 [ 44.123008] Initialize ssv6200 mac fail!!
3602 [ 44.126948] SVN version 16529
3603 [ 44.126982] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3604 [ 44.126997] COMPILER HOST icomm-buildserver-T320
3605 [ 44.127010] COMPILER DATE 12-08-2017-10:34:54
3606 [ 44.127023] COMPILER OS linux
3607 [ 44.127036] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3608 [ 44.127338] CHIP TAG: 0
3609 [ 44.127849] CHIP ID: SSV6006C0
3610 [ 44.132891] 0x800e0000
3611 [ 44.198420] ERROR!!Please check interface!
3612 [ 44.198456] [0xca000200]: 0x0c000000!=0x00000000
3613 [ 44.198469] SOS!SOS!
3614 [ 44.198481] Initialize ssv6200 mac fail!!
3615 [ 54.050317] SVN version 16529
3616 [ 54.050351] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3617 [ 54.050365] COMPILER HOST icomm-buildserver-T320
3618 [ 54.050379] COMPILER DATE 12-08-2017-10:34:54
3619 [ 54.050391] COMPILER OS linux
3620 [ 54.050404] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3621 [ 54.050715] CHIP TAG: 0
3622 [ 54.051106] CHIP ID: SSV6006C0
3623 [ 54.056114] 0x800e0000
3624 [ 54.119955] ERROR!!Please check interface!
3625 [ 54.119989] [0xca000200]: 0x0c000000!=0x00000000
3626 [ 54.120001] SOS!SOS!
3627 [ 54.120014] Initialize ssv6200 mac fail!!
3628 [ 54.123923] SVN version 16529
3629 [ 54.123963] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3630 [ 54.123980] COMPILER HOST icomm-buildserver-T320
3631 [ 54.123994] COMPILER DATE 12-08-2017-10:34:54
3632 [ 54.124007] COMPILER OS linux
3633 [ 54.124021] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3634 [ 54.124399] CHIP TAG: 0
3635 [ 54.124851] CHIP ID: SSV6006C0
3636 [ 54.129682] 0x800e0000
3637 [ 54.195350] ERROR!!Please check interface!
3638 [ 54.195385] [0xca000200]: 0x0c000000!=0x00000000
3639 [ 54.195398] SOS!SOS!
3640 [ 54.195410] Initialize ssv6200 mac fail!!
3641 [ 64.045337] SVN version 16529
3642 [ 64.045361] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3643 [ 64.045370] COMPILER HOST icomm-buildserver-T320
3644 [ 64.045377] COMPILER DATE 12-08-2017-10:34:54
3645 [ 64.045383] COMPILER OS linux
3646 [ 64.045390] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3647 [ 64.045604] CHIP TAG: 0
3648 [ 64.045838] CHIP ID: SSV6006C0
3649 [ 64.049446] 0x800e0000
3650 [ 64.098162] ERROR!!Please check interface!
3651 [ 64.098191] [0xca000200]: 0x0c000000!=0x00000000
3652 [ 64.098200] SOS!SOS!
3653 [ 64.098212] Initialize ssv6200 mac fail!!
3654 [ 64.101684] SVN version 16529
3655 [ 64.101719] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3656 [ 64.101733] COMPILER HOST icomm-buildserver-T320
3657 [ 64.101740] COMPILER DATE 12-08-2017-10:34:54
3658 [ 64.101748] COMPILER OS linux
3659 [ 64.101756] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3660 [ 64.102055] CHIP TAG: 0
3661 [ 64.102466] CHIP ID: SSV6006C0
3662 [ 64.106790] 0x800e0000
3663 [ 64.148371] ERROR!!Please check interface!
3664 [ 64.148396] [0xca000200]: 0x0c000000!=0x00000000
3665 [ 64.148404] SOS!SOS!
3666 [ 64.148411] Initialize ssv6200 mac fail!!
3667 [ 74.059189] SVN version 16529
3668 [ 74.059224] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3669 [ 74.059239] COMPILER HOST icomm-buildserver-T320
3670 [ 74.059253] COMPILER DATE 12-08-2017-10:34:54
3671 [ 74.059265] COMPILER OS linux
3672 [ 74.059278] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3673 [ 74.059727] CHIP TAG: 0
3674 [ 74.060248] CHIP ID: SSV6006C0
3675 [ 74.065159] 0x800e0000
3676 [ 74.127242] ERROR!!Please check interface!
3677 [ 74.127275] [0xca000200]: 0x0c000000!=0x00000000
3678 [ 74.127288] SOS!SOS!
3679 [ 74.127301] Initialize ssv6200 mac fail!!
3680 [ 74.131431] SVN version 16529
3681 [ 74.131463] SVN ROOT URL http://XXX.XXX.15.30/svn/software/project/release/android/box/rk3x28/6051.Q0.1009.21.400401/ssv6xxx
3682 [ 74.131478] COMPILER HOST icomm-buildserver-T320
3683 [ 74.131491] COMPILER DATE 12-08-2017-10:34:54
3684 [ 74.131503] COMPILER OS linux
3685 [ 74.131517] COMPILER OS ARCH x86_64-linux-gnu-thread-multi
3686 [ 74.131976] CHIP TAG: 0
3687 [ 74.132472] CHIP ID: SSV6006C0
3688 [ 74.137520] 0x800e0000
3689 [ 74.197666] ERROR!!Please check interface!
3690 [ 74.197701] [0xca000200]: 0x0c000000!=0x00000000
3691 [ 74.197714] SOS!SOS!
3692 [ 74.197726] Initialize ssv6200 mac fail!!
3693
3694
3695 vm.admin_reserve_kbytes = 8192
3696 vm.block_dump = 0
3697 vm.dirty_background_bytes = 0
3698 vm.dirty_background_ratio = 10
3699 vm.dirty_bytes = 0
3700 vm.dirty_expire_centisecs = 3000
3701 vm.dirty_ratio = 20
3702 vm.dirtytime_expire_seconds = 43200
3703 vm.dirty_writeback_centisecs = 500
3704 vm.drop_caches = 0
3705 vm.extra_free_kbytes = 0
3706 vm.highmem_is_dirtyable = 0
3707 vm.laptop_mode = 0
3708 vm.legacy_va_layout = 0
3709 vm.lowmem_reserve_ratio = 32 32
3710 vm.max_map_count = 65530
3711 vm.min_free_kbytes = 3924
3712 vm.mmap_min_addr = 32768
3713 vm.mmap_rnd_bits = 8
3714 vm.nr_pdflush_threads = 0
3715 vm.oom_dump_tasks = 1
3716 vm.oom_kill_allocating_task = 0
3717 vm.overcommit_kbytes = 0
3718 vm.overcommit_memory = 0
3719 vm.overcommit_ratio = 50
3720 vm.page-cluster = 0
3721 vm.panic_on_oom = 0
3722 vm.percpu_pagelist_fraction = 0
3723 vm.stat_interval = 1
3724 vm.swappiness = 100
3725 vm.user_reserve_kbytes = 30419
3726 vm.vfs_cache_pressure = 100
3727
3728 ### interrupts:
3729 CPU0 CPU1 CPU2 CPU3
3730 16: 0 0 0 0 GIC 29 Edge arch_timer
3731 17: 57476 53456 53017 55292 GIC 30 Edge arch_timer
3732 20: 0 0 0 0 GIC 75 Level rk_timer
3733 21: 0 0 0 0 GIC 32 Level 110f0000.pdma
3734 22: 0 0 0 0 GIC 33 Level 110f0000.pdma
3735 30: 11 0 0 0 GIC 89 Level serial
3736 31: 0 0 0 0 GIC 90 Level rockchip_thermal
3737 32: 0 0 0 0 GIC 38 Level Mali_GP
3738 33: 0 0 0 0 GIC 37 Level Mali_GP_MMU, Mali_PP0_MMU, Mali_PP1_MMU
3739 34: 0 0 0 0 GIC 36 Level Mali_PP0, Mali_PP1
3740 35: 0 0 0 0 GIC 41 Level 20020000.vpu-service
3741 36: 0 0 0 0 GIC 43 Level 20020000.vpu-service
3742 38: 0 0 0 0 GIC 39 Level 20030000.rkvdec
3743 40: 0 0 0 0 GIC 64 Level 20050000.vop
3744 41: 0 0 0 0 GIC 65 Level rga
3745 43: 0 0 0 0 GIC 67 Level 200a0000.hdmi, dw-hdmi-cec
3746 45: 695051 0 0 0 GIC 44 Level dw-mci
3747 46: 51216 0 0 0 GIC 45 Level dw-mci
3748 47: 22 0 0 0 GIC 47 Level nandc
3749 48: 0 0 0 0 GIC 55 Level 30040000.usb, dwc2_hsotg:usb1
3750 49: 0 0 0 0 GIC 48 Level ehci_hcd:usb2
3751 50: 0 0 0 0 GIC 49 Level ohci_hcd:usb5
3752 51: 0 0 0 0 GIC 51 Level ehci_hcd:usb3
3753 52: 0 0 0 0 GIC 52 Level ohci_hcd:usb6
3754 53: 0 0 0 0 GIC 98 Level ehci_hcd:usb4
3755 54: 0 0 0 0 GIC 99 Level ohci_hcd:usb7
3756 55: 12581 0 0 0 GIC 56 Level eth0
3757 104: 0 0 0 0 gpio1 11 Edge gpio-ir-recv-irq
3758 110: 0 0 0 0 gpio1 17 Edge �
3759 182: 0 0 0 0 gpio3 25 Edge reset
3760 189: 0 0 0 0 GIC 94 Level rockchip_usb2phy
3761 190: 0 0 0 0 GIC 100 Level rockchip_usb2phy
3762 IPI0: 0 0 0 0 CPU wakeup interrupts
3763 IPI1: 0 0 0 0 Timer broadcast interrupts
3764 IPI2: 13364 290985 32142 27986 Rescheduling interrupts
3765 IPI3: 12 1338 209 12 Function call interrupts
3766 IPI4: 0 0 0 0 CPU stop interrupts
3767 IPI5: 0 0 0 0 IRQ work interrupts
3768 IPI6: 0 0 0 0 completion interrupts
3769 Err: 0
Please upload the whole output above to an online pasteboard service
and provide the URL in the forum where you have been asked for this.