bartek666666

Okay, I'm a noob but finally it works. .dts for anyone that is curious. now i just need to enable LCD in u-boot
 
/dts-v1/; #include "sun4i-a10.dtsi" #include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/pwm/pwm.h> / { model = "Cubietech Cubieboard"; compatible = "cubietech,a10-cubieboard", "allwinner,sun4i-a10"; aliases { serial0 = &uart0; }; chosen { stdout-path = "serial0:115200n8"; }; hdmi-connector { compatible = "hdmi-connector"; type = "a"; port { hdmi_con_in: endpoint { remote-endpoint = <&hdmi_out_con>; }; }; }; }; &ahci { target-supply = <&reg_ahci_5v>; status = "okay"; }; &codec { status = "okay"; }; &cpu0 { cpu-supply = <&reg_dcdc2>; }; &de { status = "okay"; }; &ehci0 { status = "okay"; }; &ehci1 { status = "okay"; }; &emac { phy-handle = <&phy1>; status = "okay"; }; &emac_sram { status = "okay"; }; &hdmi { status = "okay"; }; &hdmi_out { hdmi_out_con: endpoint { remote-endpoint = <&hdmi_con_in>; }; }; &i2c0 { status = "okay"; axp209: pmic@34 { reg = <0x34>; interrupts = <0>; }; }; &i2c1 { status = "okay"; }; &ir0 { pinctrl-names = "default"; pinctrl-0 = <&ir0_rx_pins>; status = "okay"; }; &mdio { status = "okay"; phy1: ethernet-phy@1 { reg = <1>; }; }; &mmc0 { vmmc-supply = <&reg_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; &ohci0 { status = "okay"; }; &ohci1 { status = "okay"; }; &otg_sram { status = "okay"; }; &pio { usb0_id_detect_pin: usb0-id-detect-pin { pins = "PH4"; function = "gpio_in"; bias-pull-up; }; usb0_vbus_detect_pin: usb0-vbus-detect-pin { pins = "PH5"; function = "gpio_in"; bias-pull-down; }; }; &reg_ahci_5v { status = "okay"; }; #include "axp209.dtsi" &ac_power_supply { status = "okay"; }; &reg_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1400000>; regulator-name = "vdd-cpu"; }; &reg_dcdc3 { regulator-always-on; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1250000>; regulator-name = "vdd-int-dll"; }; &reg_ldo1 { regulator-name = "vdd-rtc"; }; &reg_ldo2 { regulator-always-on; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; regulator-name = "avcc"; }; &reg_usb0_vbus { status = "okay"; }; &reg_usb1_vbus { status = "okay"; }; &reg_usb2_vbus { status = "okay"; }; &spi0 { pinctrl-names = "default"; pinctrl-0 = <&spi0_pi_pins>, <&spi0_cs0_pi_pin>; status = "okay"; }; &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; &usb_otg { dr_mode = "host"; status = "okay"; }; &usbphy { pinctrl-names = "default"; pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */ usb0_vbus_det-gpio = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */ usb0_vbus-supply = <&reg_usb0_vbus>; usb1_vbus-supply = <&reg_usb1_vbus>; usb2_vbus-supply = <&reg_usb2_vbus>; status = "okay"; };