Jump to content


  • Posts

  • Joined

  • Last visited

 Content Type 


Member Map




Everything posted by MR01

  1. Remember that with IP will change after 72h of system-up, just remove ,72h for always. Probably my mistake, should be all if i remember right, anyway im using it as cheap low latency powerfull wifi-eth for my gaming pc.
  2. When i had the same problem i just expanded the partition with gparted.
  3. To update the Lima driver question ON or OFF dmesg | grep lima [ 7.913523] lima ff300000.gpu: gp - mali450 version major 0 minor 0 [ 7.913612] lima ff300000.gpu: pp0 - mali450 version major 0 minor 0 [ 7.913675] lima ff300000.gpu: pp1 - mali450 version major 0 minor 0 [ 7.913731] lima ff300000.gpu: l2 cache 8K, 4-way, 64byte cache line, 128bit external bus [ 7.913746] lima ff300000.gpu: l2 cache 64K, 4-way, 64byte cache line, 128bit external bus [ 7.915008] lima ff300000.gpu: bus rate = 491520000 [ 7.915046] lima ff300000.gpu: mod rate = 491520000 [ 7.917641] [drm] Initialized lima 1.1.0 20191231 for ff300000.gpu on minor 1
  4. i only have /etc/X11/xorg.conf.d/01-armbian-defaults.conf I dont think i removed or deleted it by accident because i never installed DE in this installation of minimal.
  5. Chrome probably is missing OpenGL/OpenGL ES features that mainline kernel miss. My bad on 3D with Lima driver.
  6. I did install lightdm+lxde[core-minimal] on debian minimal without big problems. But i removed all after finding out that hw accelleration didnt work on 5.15 kernel, so chrome will not run at all for example, and i old kernel was not running my usb dongle by default.
  7. The user @hannah had the same AP6330 and bth BCM4330B1 in a s905x3 box and fixed with meson-sm1-sei610-x96maxplus.dtb Im adding this info for future reference and fixing/implementation @jock meson-sm1-sei610-x96maxplus.dtb
  8. AP6330 with a metal plate. Seems recognized and working NOW, yesterday didnt and i tried many times with many reboots, the only thing i did in late night (so right before now dmesg) was set in rc.local "ifconfig wlan0 down" because im using a powerfull external usb dongle. So maybe when wifi is off bth works? Im not fond of kernel/drivers in general so maybe is no-sense. I dont plan to use bth anyway. Ps: im using this box as a powerfull switch WIFI>ETH because my house is on 2 plans and my only telephone port is in the plan down my actual pc and there must be the router....plus every plan is electrically "indipendent" with 2 different save-life (so i dont even try to use powerline), so for better signal i will put the box in a better position with a ethernet cable running side-wall from the box to my pc dmesg.txt
  9. I made a guide after resolving the problem on my own after many not working guides.
  10. i have the same board of @markst precisely a X88-PRO-B-RK3318-D4-V1.2, but selled with a different name (QPLOVE Q9 4/128 [ram/emmc]) so maybe something is different, wifi works bth not. And as the others guys with 4gb ram i can only use 2gb of ram. Firmware: BCM4330/4 wl0
  11. There is no correlation just a problem in find and activate the right driver, the hw/chip of the usb bth dongle is present in the kernel linux while the internal chip not. Did you try with console commands? Did you try to disconnect the usb and still use bth?
  12. @awawa@markst I found out how POWEROFF the RED led of SPIDF echo 1 > /sys/class/leds/working/brightness Strange as it can be 1 = OFF and 0 = ON @jock Grazie ancora per tutto quello che fai!!
  13. Hi i have also a x88 Pro board, wifi now works i had 5.15.35 from start but no one said the trick of double rk3318-config with the reboot so i found it out only now. i found this in xda forum, leading the idea that bcm4334W is compatible with bcm43342A, fixing wifi+bth on android. I dont know how/where get that .hcd, did you guys tried that already? Thanks a lot to @jock and @awawa ^^
  14. Hello im new and im Italian so i hope you will not hate me if i write not perfectly (Who said Google Translate?? No No No) This Guide is for a "client to client" setup of the box, we will internally switch Wifi to Eth, so a working computer can access internet from its eth port even if the router signal source is wireless. Router AP -----> ARM BOX [WIFI internal or usb dongle] ===>> internal eth0 ------> ethernet cable --> client eth port Make sure WiFi in arm box is connected using nmtui command FROM NOW ON <WIFI CARD> is the wifi adapter name es: replace "<WIFI CARD>" with "wlx0013eff301ee" Execute: sudo apt-get update && sudo apt-get install dnsmasq iptables iptables-persistent -y say no to save actual iptables rules (we dont have any yet) Edit /etc/network/interfaces comment if exist the part of eth0 "iface eth0" to "#iface eth0" add those lines allow-hotplug eth0 iface eth0 inet static address netmask network broadcast dns-nameservers #########{Static}########### up ip addr add dev eth0 execute those commands REMEMBER TO REPLACE <WIFI CARD> ip addr add dev eth0 iptables -A FORWARD -o <WIFI CARD> -i eth0 -s -m conntrack --ctstate NEW -j ACCEPT iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT iptables -t nat -F POSTROUTING iptables -t nat -A POSTROUTING -o <WIFI CARD> -j MASQUERADE sh -c "iptables-save > /etc/iptables.ipv4.nat" sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" /etc/init.d/dnsmasq stop cp /etc/dnsmasq.conf /etc/dnsmasq.conf-backup Edit /etc/dnsmasq.conf inserting interface=eth0 listen-address= bind-interfaces server= domain-needed bogus-priv dhcp-range=,,72h Edit /etc/sysctl.conf inserting net.ipv4.conf.default.forwarding=1 net.ipv4.conf.all.forwarding=1 Edit /etc/rc.local inserting before "exit 0" iptables-restore < /etc/iptables.ipv4.nat execute those commands systemctl enable dnsmasq systemctl enable iptables Explainations: We set static net to eht0 then we set routing in iptables [forward and back] wlan<->eth then we make this setup persistent so that will persist after reboot. Working on my RK3318 Armbian bullseye 5.15 minimal and USB3 dongle RTL8814AU (also tested with a 8812au)
  • Create New...