@sven-ola
Have you tried booting from a microSD card?
I downloaded Armbian-unofficial_26.02.0-trunk_Orangepirv2_trixie_current_6.18.18_gnome_desktop.img and flashed it to my microSD card, but it won't boot.
log:
sys: 0x200
try sd...
bm:3
j...
U-Boot SPL 2022.10_armbian-2022.10-Sd61c-P155c-H452d-V4161-B61c5-R448a (Mar 17 2026 - 03:52:17 +0000)
[ 0.381] DDR type LPDDR4X
[ 0.383] set ddr tx odt to 80ohm!
[ 0.393] lpddr silicon init consume 11ms
[ 0.394] Change DDR data rate to 2400MT/s
[ 0.633] Boot from fit configuration x1_orangepi-rv2
[ 0.635] ## Checking hash(es) for config conf_18 ... OK
[ 0.641] ## Checking hash(es) for Image uboot ... crc32+ OK
[ 0.652] ## Checking hash(es) for Image fdt_18 ... crc32+ OK
[ 0.674] ## Checking hash(es) for config config_1 ... OK
[ 0.677] ## Checking hash(es) for Image opensbi ... crc32+ OK
[ 0.725]
U-Boot 2022.10_armbian-2022.10-Sd61c-P155c-H452d-V4161-B61c5-R448a (Mar 17 2026 - 03:52:17 +0000)
[ 0.732] CPU: rv64imafdcv
[ 0.734] Model: ky x1 orangepi-rv2 board
[ 0.738] DRAM: 2 GiB
[ 0.830] Core: 414 devices, 29 uclasses, devicetree: board
[ 0.843] WDT: Started PMIC_WDT with servicing (60s timeout)
[ 0.848] WDT: Started watchdog@D4080000 with servicing (60s timeout)
[ 0.857] MMC:
[ 0.956] *** Warning - bad CRC, using default environment
[ 0.961] initialize_console_log_buffer
[ 0.962] Have allocated memory for console log buffer
[ 0.967] In: serial
[ 0.969] Out: serial
[ 0.971] Err: serial
[ 1.116] k1x_qspi spi@d420c000: qspi iobase:0x0x00000000d420c000, ahb_addr:0x0x00000000b8000000, max_hz:26500000Hz
[ 1.124] k1x_qspi spi@d420c000: rx buf size:128, tx buf size:256, ahb buf size=512
[ 1.131] k1x_qspi spi@d420c000: AHB read enabled
[ 1.136] k1x_qspi spi@d420c000: bus clock: 26500000Hz, PMUap reg[0xd4282860]:0x0000075b
[ 1.143] k1x_qspi spi@d420c000: AHB buf size: 512
[ 1.148] SF: Detected XM25QU128C with page size 256 Bytes, erase size 64 KiB, total 16 MiB
List of MTD devices:
[ 1.159] * nor0
[ 1.160] - device: flash@0
[ 1.163] - parent: spi@d420c000
[ 1.166] - driver: jedec_spi_nor
[ 1.170] - path: /soc/spi@d420c000/flash@0
[ 1.173] - type: NOR flash
[ 1.176] - block size: 0x10000 bytes
[ 1.180] - min I/O: 0x1 bytes
[ 1.183] - 0x000000000000-0x000001000000 : "nor0"
[ 1.188] - 0x000000000000-0x000000010000 : "bootinfo"
[ 1.193] - 0x000000010000-0x000000020000 : "private"
[ 1.198] - 0x000000020000-0x000000060000 : "fsbl"
[ 1.203] - 0x000000060000-0x000000070000 : "env"
[ 1.208] - 0x000000070000-0x0000000a0000 : "opensbi"
[ 1.213] - 0x0000000a0000-0x000001000000 : "uboot"
[ 1.219] Failed to get fastboot key config: -19
[ 1.222] Failed to probe HUSB239: -19
[ 1.227] RGMII interface
[ 1.228] eth0: ethernet@cac80000
[ 1.231] MAC mapping file path not set in environment
[ 1.236] K1X: :_load_env_from_blk
[ 1.247] Can't set block device
[ 1.248] Net: eth0: ethernet@cac80000
[ 1.254] Hit any key to stop autoboot: 0
Loading K1-X Environment ...
[ 2.260]
[ 2.261] Running NVMe Scan ...
[ 2.272] pcie_dw_k1x pcie@ca400000: has no power-on-status flag, use default.
[ 2.277] Now init Rterm...
[ 2.279] pcie prot id = 1, porta_init_done = 0
[ 2.283] Now waiting portA resister tuning done...
[ 2.288] porta redonly_reg2: 00005d37
[ 2.292] pcie_rcal = 0x00005d37
[ 2.295] pcie port id = 1, lane num = 2
[ 2.298] Now int init_puphy...
[ 2.301] waiting pll lock...
[ 2.304] Now finish init_puphy....
[ 2.307] pcie_dw_k1x pcie@ca400000: Unable to get phy0
[ 2.312] pcie_dw_k1x pcie@ca400000: Unable to get phy1
[ 2.317] pcie_dw_k1x pcie@ca400000: PCIe interface power on, set gpio 116 to 1
[ 3.426] PCIE-0: Link down
[ 3.438] pcie_dw_k1x pcie@ca800000: has no power on gpio.
[ 3.441] pcie_dw_k1x pcie@ca800000: has no power-on-status flag, use default.
[ 3.448] Now init Rterm...
[ 3.450] pcie prot id = 2, porta_init_done = 0
[ 3.455] Now waiting portA resister tuning done...
[ 3.459] porta redonly_reg2: 00005d37
[ 3.463] pcie_rcal = 0x00005d37
[ 3.466] pcie port id = 2, lane num = 2
[ 3.470] Now int init_puphy...
[ 3.472] waiting pll lock...
[ 3.475] Now finish init_puphy....
[ 3.479] pcie_dw_k1x pcie@ca800000: Unable to get phy0
[ 3.484] pcie_dw_k1x pcie@ca800000: Unable to get phy1
[ 4.590] PCIE-1: Link down
[ 4.642] pcie_dw_k1x pcie@ca400000: has no power-on-status flag, use default.
[ 4.646] Now init Rterm...
[ 4.648] pcie prot id = 1, porta_init_done = 0
[ 4.653] Now waiting portA resister tuning done...
[ 4.657] porta redonly_reg2: 00005d37
[ 4.661] pcie_rcal = 0x00005d37
[ 4.664] pcie port id = 1, lane num = 2
[ 4.668] Now int init_puphy...
[ 4.671] waiting pll lock...
[ 4.673] Now finish init_puphy....
[ 4.677] pcie_dw_k1x pcie@ca400000: Unable to get phy0
[ 4.682] pcie_dw_k1x pcie@ca400000: Unable to get phy1
[ 4.687] pcie_dw_k1x pcie@ca400000: PCIe interface power on, set gpio 116 to 1
[ 5.795] PCIE-0: Link down
[ 5.807] pcie_dw_k1x pcie@ca800000: has no power on gpio.
[ 5.810] pcie_dw_k1x pcie@ca800000: has no power-on-status flag, use default.
[ 5.817] Now init Rterm...
[ 5.819] pcie prot id = 2, porta_init_done = 0
[ 5.824] Now waiting portA resister tuning done...
[ 5.828] porta redonly_reg2: 00005d37
[ 5.832] pcie_rcal = 0x00005d37
[ 5.835] pcie port id = 2, lane num = 2
[ 5.839] Now int init_puphy...
[ 5.841] waiting pll lock...
[ 5.844] Now finish init_puphy....
[ 5.848] pcie_dw_k1x pcie@ca800000: Unable to get phy0
[ 5.853] pcie_dw_k1x pcie@ca800000: Unable to get phy1
[ 6.959] PCIE-1: Link down
[ 6.963]
no nvme partition table available
[ 6.964] Couldn't find partition nvme 0:1
[ 6.968] Couldn't find partition nvme 0:1
[ 6.972] Couldn't find partition nvme 0:1
[ 6.976] Couldn't find partition nvme 0:1
[ 6.980] Couldn't find partition nvme 0:1
=>
